Weslo Momentum 610 User Manual

QUESTIONS?

As a manufacturer, we are com­mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.

CALL TOLL-FREE:

1-866-699-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

ON THE WEB:
www.wesloservice.com

CAUTION

Read all precautions and instruc­tions in this manual before using
this equipment. Keep this manu­al for future reference.

Model No. WLEL1405.1
Serial No.

Serial Number

Decal

USER’S MANUAL

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

2

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precau-

tions before using the elliptical exerciser.

1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser.

2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.

3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu­tional setting.

4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis­mount, and use it.

5. Inspect and properly tighten all parts regu­larly. Replace any worn parts immediately.

6. Keep children under 12 and pets away from
the elliptical exerciser at all times.

7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.

8. Wear appropriate exercise clothes when
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer­cising.

9. Hold the handlebars when mounting, dis­mounting, or using the elliptical exerciser.

10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin­ing heart rate trends in general.

11. Keep your back straight when using the ellip­tical exerciser; do not arch your back.

12. If you feel pain or dizziness while exercising,
stop immediately and cool down.

13. When you stop exercising, allow the pedals
to slowly come to a stop.

14. The decal shown on page 3 has been placed
on the elliptical exerciser. If a decal is miss­ing or illegible, call the toll-free telephone
number on the front cover of this manual
and order a free replacement decal. Apply
the decal in the location shown.

WARNING: Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob­lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

3

BEFORE YOU BEGIN

Congratulations for selecting the new WESLO

®

MOMENTUM 610 elliptical exerciser. The MOMEN­TUM 610 elliptical exerciser is an incredibly smooth
exerciser that moves your feet in a natural elliptical
path, minimizing the impact on your knees and
ankles. And the unique MOMENTUM 610 features
adjustable resistance and a simple-to-use console to
help you get the most from your exercise.

For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-

tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the

product model number and serial number before call­ing. The model number is WLEL1405.1. The serial
number can be found on a decal attached to the ellip­tical exerciser (see the front cover of this manual for
the location of the decal).

To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.wesloservice.com/registration.

Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.

Handlebar

FRONT

BACK

Pedal Arm

Pedal Disk

*No water bottle is included

Pedal

Console

Water Bottle Holder*

Resistance Knob

ASSEMBLY

To hire an authorized service technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included allen wrenches, assembly requires a Phillips screwdriver , an adjustable
wrench , and a rubber mallet .

As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST on page 14. The second number is the
quantity needed for assembly. Note: Some small parts may have been pre-assembled. If a part is not in the

parts bag, check to see if it has been pre-assembled.

4

1. Identify the Front Stabilizer (10), which is narrower than
the Rear Stabilizer (not shown). While another person
lifts the front of the Frame (1), attach the Front
Stabilizer to the Frame with two M10 x 75mm Carriage
Bolts (34) and two M10 Nylon Locknuts (33).

10

33

34

1

1

M6 Nylon

Locknut (27)–4

M4 x 12mm

Screw (43)–5

M6 x 38mm Button Bolt (50)–4

M10 Nylon

Locknut (33)–6

M6 x 45mm Flat Head

M10 Split

Washer (59)–2

Screw (36)–4

Wave Washer

(64)–2

Pedal Arm Bolt Set (40)–2

M10 x 75mm Carriage Bolt (34)–4M10 x 68mm Button Bolt (48)–2

M10

Washer (35)–2

M10 x 25mm

Patch Screw (22)–2

5

2. While another person lifts the back of the Frame (1),

attach the Rear Stabilizer (28) to the Frame with two
M10 x 75mm Carriage Bolts (34) and two M10 Nylon
Locknuts (33).

34

28

1

2

33

33

3. The Console (23) requires three “AA” batteries (not

included); alkaline batteries are recommended. Insert
three batteries into the battery compartment. Make

sure that the batteries are oriented as shown by
the diagram inside the battery compartment.

23

Batteries

3

4. While another person holds the Console (23) near the

Upright (2), connect the console wire to the Upper
Wire (44). Next, attach the ground wire to the Upright
with an M4 x 12mm Screw (43). Insert the console
wire and the Upper Wire into the Upright, and insert
the ground wire into the Console.

Next, attach the Console (23) to the Upright (2) with
four M4 x 12mm Screw (43). Be careful to avoid

pinching the console wire, the ground wire, or the
Upper Wire (44).

Turn the Resistance Knob (63) counterclockwise to
the lowest setting before going to the next step.

4

23

2

44

63

Console Wire

Ground Wire

43

43

5

1

2

33

Make sure that

the wires and
cables do not

get pinched

and damaged

during this

step.

44

53

48

55

63

59

5. While another person holds the Upright (2) near the

Frame (1), connect the Upper Wire (44) to the Reed
Switch Wire (53). Next, connect the Resistance Cable
(63) to the Lower Cable (55) in the following way:

• See drawing A. Pull up on the metal bracket on the
Lower Cable (55), and insert the tip of the
Resistance Cable (63) into the wire clip inside of the
metal bracket.

• See drawing B. Firmly pull the Resistance Cable
(63) and slide it into the metal bracket on the Lower
Cable (55) as shown.

• See drawing C. Using pliers, squeeze together the
prongs on the upper end of the metal bracket.

Push the excess cable and wire down into the Frame
(1). Next, slide the Upright (2) onto the Frame. Be
careful not to pinch the wires or cables. Attach the
Upright with two M10 x 68mm Button Bolts (48), two
M10 Split Washers (59), and two M10 Nylon Locknuts
(33). Do not tighten the Button Bolts yet.

55

55

Metal

Bracket

B

A

C

55

63

63

63

6

50

8

27

6. Identify the Left Handlebar (6), which is marked with a
sticker. Insert the Left Handlebar into one of the
Handlebar Arms (5); make sure that the Handlebar

Arm is turned so the hexagonal holes are on the
indicated side. Attach the Left Handlebar to the

Handlebar Arm with two M6 x 38mm Button Bolts (50)
and two M6 Nylon Locknuts (27). Make sure that the

Nylon Locknuts are inside of the hexagonal holes.
Do not fully tighten the Button Bolts yet.

Apply a small amount of the included grease to the left
axle on the Upright (2).

Make sure that there are two Small Handlebar
Bushings (49) in the Left Handlebar (6). Slide a
Handlebar Spacer (47) and the Left Handlebar onto the
left axle on the Upright (2) as shown. Make sure that the

Handlebar Spacer is turned so the curved side is fac­ing the Upright. Tap an Axle Cap (14) onto the axle.

Repeat this step to assemble the Right Handlebar (8)
and the other Handlebar Arm (5).

Grease

6

47

14

49

5

2

5

6

7

36

11

13

7. Identify the Left Pedal Arm (11). Attach a Pedal (13) to
the Left Pedal Arm with two M6 x 45mm Flat Head
Screws (36).

Attach the other Pedal to the Right Pedal Arm (not
shown) in the same way.

Hexagonal

Holes

7

9. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be

left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the ellip­tical exerciser.

8. Apply a small amount of grease to the axle on the left
Disc Crossbar (16). Slide the Left Pedal Arm (11) onto
the axle, and place a Wave Washer (64) on the end of
the axle. Next, slide an M10 Washer (35) onto an M10 x
25mm Patch Screw (22), and tighten the Patch Screw
into the axle.

Hold the lower end of the left Handlebar Arm (5) inside
of the bracket on the Left Pedal Arm (11). Next, apply
grease to a Pedal Arm Bolt Set (40). Attach the Left
Pedal Arm to the left Handlebar Arm with the Bolt Set.

Do not overtighten the Bolt Set; the Handlebar Arm
must pivot freely.

Attach the Right Pedal Arm (not shown) to the right
side of the elliptical exerciser in the same way.

See step 5. Tighten the M10 x 68mm Button Bolts (48).

See step 6. Tighten the M6 x 38mm Button Bolts (50)
in the Handlebar Arms (5).

Grease

Grease

22

35

11

5

8

16

40

40

64

8

HOW TO USE THE ELLIPTICAL EXERCISER

HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER

To mount the elliptical exerciser, hold the handlebars
and step onto the pedal that is in the lowest position.
Then, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:

The pedal disks can turn in either direction. It is
recommended that you move the pedal disks in
the direction shown by the arrow; however, for
variety, you may turn the pedal disks in the oppo­site direction.

To dismount the elliptical exerciser, wait until the ped­als come to a complete stop. Note: The elliptical

exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.

When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.

HOW TO ADJUST THE PEDALING RESISTANCE

As you exercise,
you can adjust the
resistance of the
pedals with the
resistance knob on
the upright. To
increase the resis­tance, turn the
knob clockwise; to
decrease the resis­tance, turn the
knob counterclock­wise.

Pedal Disk

Pedal

Handlebars

Resistance

Knob

9

FEATURES OF THE CONSOLE

The console features a selection of modes that pro­vide instant exercise feedback during your workouts.
The modes are described below.

• Speed—This mode displays your pedaling speed, in

miles per hour or kilometers per hour.

• Time—This mode displays the elapsed time. Note:

If you stop pedaling for a few seconds, the time
mode will pause.

• Distance—This mode displays the distance you

have pedaled, in miles or kilometers.

• Calories—This mode displays the approximate

number of calories you have burned.

• Fat Calories—This mode displays the approximate

number of fat calories you have burned (see FAT
BURNING on page 13).

• Pulse—This mode displays your heart rate when

you use the pulse sensor.

• Scan—This mode displays the speed, time, dis-

tance, calories, fat calories, and pulse modes, for a
few seconds each, in a repeating cycle. Note: The
pulse mode will be displayed only when the pulse
sensor is being used.

• Pace—The pace bar shows your pedaling pace, in

revolutions per minute (RPM). Note: The pace mode
will always be displayed while you are pedaling.

HOW TO OPERATE THE CONSOLE

Make sure there are batteries in the console (see
BATTERY REPLACEMENT on page 11). If there is a
sheet of clear plastic on the console, remove it.

Follow the steps below to operate the console.

1. To turn on the console, press the ON/RESET but­ton or begin pedaling. The entire display will briefly
appear; the console will then be ready for use.

2. Select one of the modes:

Scan mode—
When the power
is turned on, the
scan mode will be
selected automati­cally. One mode
indicator will
appear below the
word SCAN to
show that the
scan mode is
selected, and a second mode indicator will show
which mode is currently displayed. Note: If you
have selected a different mode, press the MODE
button repeatedly to reselect the scan mode.

Speed, time, dis­tance, calories,
or fat calories
mode—To select

one of these
modes for contin­uous display,
press the MODE
button repeatedly.
The mode indicators will show which mode is
selected. Make sure there is not a mode indicator
below the word SCAN.

To reset the display, press the ON/RESET button.

Note: The console can display speed and dis­tance in either miles or kilometers. To change
the unit of measurement, press the ON/RESET
button for about five seconds. The letters mph or

km/h will appear in the display to show which unit of
measurement is selected. When the batteries are
replaced, it may be necessary to reselect the
desired unit of measurement.

Mode Indicators

10

3. Measure your heart rate, if desired.

To measure your
heart rate, stop
pedaling and
place your thumb
on the pulse sen­sor as shown. Do

not press too
hard, or the cir­culation in your
thumb will be
restricted and
your pulse will
not be detected.

After a few sec­onds, the heart­shaped indicator
in the display will
flash steadily,
two dashes will
appear, and then
your heart rate
will be shown. Hold your thumb on the pulse sensor
for about 15 seconds for the most accurate reading.

If the displayed heart rate appears to be too high or
too low, or if your heart rate is not displayed, lift
your thumb off the pulse sensor for a few seconds.
Then, place your thumb on the pulse sensor as
described above.

Make sure you are applying the proper amount of
pressure to the pulse sensor. Try the pulse sensor
several times until you become familiar with it.
Remember to stand still while measuring your heart
rate.

4. To turn off the console, simply wait for a few min-

utes. The console has an “auto-off” feature. If

the pedals are not moved and the console but­tons are not pressed for a few minutes, the
power will turn off automatically to save the
batteries.

WARNING: The pulse sensor

is not a medical device. Various factors
may affect the accuracy of heart rate read­ings. The pulse sensor is intended only as
an exercise aid in determining heart rate
trends in general.

Pulse Sensor

11

Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. Important: Keep liq-

uids away from the console, place only a sealed
water bottle in the water bottle holder, and keep
the console out of direct sunlight. During storage,
remove the batteries from the console.

BATTERY REPLACEMENT

If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
step 4 on page 5 and remove the console from the
upright. Next, see step 3 on page 5 and insert three
batteries into the console. Reattach the console to the
upright, being careful not to pinch the wires.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, you must remove the Left Pedal Arm (11) and
the Left Side Shield (3).

Remove the Pedal Arm Bolt Set (40), the M10 x
25mm Patch Screw (22), the M10 Washer (35), and
the Wave Washer (64) from the Left Pedal Arm (11).
Remove the Left Pedal Arm. Next, remove the two M4
x 25mm Screws (56) and the four M4 x 16mm Screws
(42) from the Left Side Shield (3).

See the drawing below and locate the Reed Switch
(53). Loosen, but do not remove, the indicated M4 x
16mm Screw (42). Slide the Reed Switch slightly
toward or away from the Magnet (58) on the flywheel.
Then, retighten the Screw. Turn the left Pedal Disc (15)
for a moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjusted,
reattach the Left Side Shield (3) and the Left Pedal
Arm (11).

HOW TO ADJUST THE DRIVE BELT

If the pedals slip while you are pedaling, even when
the resistance is adjusted to the highest setting, the
Drive Belt (19) may need to be adjusted. To adjust the
Drive Belt, you must first remove the left side shield.
See HOW TO ADJUST THE REED SWITCH at the
left and remove the left side shield.

Next, loosen the
M8 x 22mm Flat
Head Screw
(41) and turn
the M10 x
60mm Bolt (62)
until the Drive
Belt (19) is tight.
When the Drive
Belt is tight,
tighten the Flat
Head Screw.
Reattach the left
side shield.

MAINTENANCE AND TROUBLESHOOTING

42

56

42

42

22

64

3

40

15

41

62

19

35

11

58

53

42

12

HOW TO ADJUST THE RESISTANCE STRAP

If the resistance knob is turned to the highest setting
and there is not enough pedaling resistance, the
resistance strap can be adjusted. To adjust the resis­tance strap, first remove the left side shield (see HOW
TO ADJUST THE REED SWITCH on page 11).

Next, turn the resistance knob to the lowest setting.
Open the Strap Clamp (26) and pull the end of the
Resistance Strap (18) downward slightly. Close the
Strap Clamp and turn the Flywheel (17) to make sure
that there is not too much resistance.

When the resistance strap is properly adjusted, re­attach the left side shield and the left pedal arm.

18

17

26

CONDITIONING GUIDELINES

The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom­mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.

To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lowest number is the recommended heart rate for
fat burning; the middle number is the recommended
heart rate for maximum fat burning; the highest num­ber is the recommended heart rate for aerobic exer­cise.

Fat Burning

To burn fat effectively, you must exercise at a relative­ly low intensity level for a sustained period of time.

During the first few minutes of exercise, your body
uses easily accessible

carbohydrate

calories for ener­gy. Only after the first few minutes of exercise does
your body begin to use stored

fat

calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num­ber in your training zone as you exercise. For maxi­mum fat burning, adjust the intensity of your exercise
until your heart rate is near the middle number in your
training zone as you exercise.

Aerobic Exercise

If your goal is to strengthen your cardiovascular sys­tem, your exercise must be “aerobic.” Aerobic exer­cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.

WORKOUT GUIDELINES

Each workout should include the following three parts:

A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa­ration for exercise.

Training zone exercise, consisting of 20 to 30 min­utes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise pro­gram, do not keep your heart rate in your training
zone for longer than 20 minutes.)

A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.

EXERCISE FREQUENCY

To maintain or improve your condition, plan three work­outs each week, with at least one day of rest between
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired. Remember, the key to success is make exer­cise a regular and enjoyable part of your everyday life.

WARNING: Before beginning

this or any exercise program, consult your
physician. This is especially important for
persons over the age of 35 or persons with
pre-existing health problems.

The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin­ing heart rate trends in general.

13

14

Note: # indicates a non-illustrated part. Specifications are subject to change without notice.

Key No. Qty. Description Key No. Qty. Description

PART LIST—Model No. WLEL1405.1 R0406A

1 1 Frame
2 1 Upright
3 1 Left Side Shield
4 1 Right Side Shield
5 2 Handlebar Arm
6 1 Left Handlebar
7 1 Idler Assembly
8 1 Right Handlebar

9 1 Hook
10 1 Front Stabilizer
11 1 Left Pedal Arm
12 1 Right Pedal Arm
13 2 Pedal
14 2 Axle Cap
15 2 Pedal Disc
16 2 Disc Crossbar
17 1 Flywheel
18 1 Resistance Strap
19 1 Drive Belt
20 1 Cable Clamp
21 4 Endcap
22 2 M10 x 25mm Patch Screw
23 1 Console
24 2 Handgrip
25 1 M6 x 16mm Bolt
26 1 Strap Clamp
27 5 M6 Nylon Locknut
28 1 Rear Stabilizer
29 2 Flywheel Bearing
30 2 Large Snap Ring
31 2 Large Bearing
32 1 Pedal Axle
33 7 M10 Nylon Locknut
34 4 M10 x 75mm Carriage Bolt
35 2 M10 Washer

36 4 M6 x 45mm Flat Head Screw
37 2 Pedal Arm Bushing
38 1 M8 Nylon Locknut
39 2 M10 Small Washer
40 2 Pedal Arm Bolt Set
41 1 M8 x 22mm Flat Head Screw
42 9 M4 x 16mm Screw
43 5 M4 x 12mm Screw
44 1 Upper Wire
45 1 Resistance Control/Cable
46 2 Handlebar Cap
47 2 Handlebar Spacer
48 2 M10 x 68mm Button Bolt
49 4 Small Handlebar Bushing
50 4 M6 x 38mm Button Bolt
51 8 M6 x 35mm Button Screw
52 1 M4 x 16mm Flat Head Screw
53 1 Reed Switch/Wire
54 1 Cable Clamp
55 1 Lower Cable
56 2 M4 x 25mm Screw
57 1 M10 Flat Head Bolt
58 1 Magnet
59 2 M10 Split Washer
60 4 Large Handlebar Bushing
61 2 5/16” x 25.4mm Hex Bolt
62 1 M10 x 60mm Bolt
63 1 Resistance Knob/Cable
64 2 Wave Washer
65 2 Inner Pedal Arm Bushing
66 1 M5 x 15mm Flat Head Screw

# 1 Allen Wrench
# 1 Grease
# 1 User’s Manual

EXPLODED DRAWING—Model No. WLEL1405.1 R0406A

15

50

5

60

36

42

27

65

42

13

4

51

25

42

22

35

64

37

42

48

45

27

60

63

8

49

42

14

60

42

56

3

42

40

39

40

20

12

18

50

5

17

24

46

24

46

6

43

49

27

49

14

44

60

47

33

21

23

43

49

47

66

2

59

59

40

21

11

40

19

35

34

64

22

36

37

51

51

13

15

10

51

65

42

55

53

61

54

33

16

52

41

31

30

57

39

26

33

29

32

7

62

1

58

21

38

29

33

31

33

30

16

33

9

61

21

28

51

15

34

Part No. 232332 R0406A Printed in China © 2006 ICON IP, Inc.

To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:

• the MODEL NUMBER of the product (WLEL1405.1)

• the NAME of the product (WESLO MOMENTUM 610 elliptical exerciser)

• the SERIAL NUMBER of the product (see the front cover of this manual)

• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING on
pages 14 and 15)

ORDERING REPLACEMENT PARTS

LIMITED WARRANTY

ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur­chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim­ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. For
in-home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con­nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci­dental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

WESLO is a registered trademark of ICON IP, Inc.