QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete satisfaction through direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Model No. WEBE11880
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal
USERÕS MANUAL
PATENT PENDING
2
Warning Decal Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Adjusting the Weight Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Exercise Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Table of Contents
The decals shown below have been placed on the weight bench. If a decal is missing, or if it is not legible, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays), to order a replacement decal. Apply the replacement decal to the location shown.
Warning Decal Placement
Note: A Part List, Exploded Drawing and Part Identification Chart is attached to the center of this manual.
Remove these four pages before beginning assembly.
3
1. Read all instructions in this manual before
using the weight bench.
2. Use the weight bench only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
6. Keep children under the age of 12 and pets
away from the weight bench at all times.
7. Always use an equal amount of weight on
each side of the barbell (not included).
8. Do not use a barbell (not included) that is
longer than five feet with the weight bench.
9. When you are using the leg lever, place a
barbell (not included) with the same amount
of weight on the weight rests to balance the
bench.
10. Always wear athletic shoes for foot protection while exercising.
11. Keep hands and feet away from moving parts.
12. The weight bench is designed to support a
maximum of 360 pounds, including the user,
a weight bar, and weights. Do not place more
than 110 pounds, including a barbell and
weights, on the weight rests; do not place
more than 50 pounds on the leg lever for
normal use.
13. When using the backrest in an inclined position, make sure that the support rod is fully
inserted into the uprights and that the locking hook is in place.
14. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
15. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental or institutional setting.
16. When you are using the lat bar, always stand
clear of the lat upright since the weight carriage will swing around the upright as it is
raised.
17. Always disconnect the lat bar from the
weight bench when you are performing an
exercise that does not use the lat bar.
18. Never let go of the lat bar when you have
weights raised. The weight carriage will fall
with great force that may cause injury or
damage the weight bench.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
To reduce the risk of serious injury, read the following important
precautions before using the weight bench.
WARNING:
Important Precautions
4
Thank you for selecting the versatile WEIDER¨T28
Weight Bench. The WEIDER¨T28 is designed to help
you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic muscle size and strength or a healthier cardiovascular system, the T28 Weight Bench will help you achieve the
specific results you want.
For your benefit, read this manual carefully before
using the WEIDER¨T28 Weight Bench. If you have
additional questions, please call our Customer Service
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is WEBE11880. The
serial number can be found on a decal attached to the
WEIDER¨T28 Weight Bench (see the front cover of
this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Before You Begin
Seat
Weight Tube
Lat Upright
Weight Rest
Right
Side
Left Side
Leg Lever
Weight Tube
Upright
Foam Pads
Lat Bar
Cable
Weight Carriage
Carriage Pin
Backrest
5
1. Before assembling this product, make sure you
have read and understand the information in the
box above.
Place the Seat Base (50) on the floor next to the
Tower Base (57), as shown in drawing 1.
See drawing 1A. Slide two 5/16Ó x 1 1/2Ó Bolts (56)
through the holes in the indicated bracket on the Seat
Base (50). Slide a 1/2Ó Spacer (54) onto each Bolt.
Slide the Seat Base (50) up next to the Tower Base
(57), and slide the two 5/16Ó x 1 1/2Ó Bolts (56)
through the indicated holes in the Tower Base.
Slide a 5/16Ó Washer (53) onto each of the 5/16Ó x 1
1/2Ó Bolts (56) and secure the Bolts with two 5/16Ó
Nylon Locknuts (15). Do not tighten the Nylon
Locknuts yet.
1
1A
Before beginning assembly, carefully read the
following information and instructions:
¥ Assembly requires two people.
¥ Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
¥ For help identifying the small parts, use the PART
IDENTIFICATION CHART on page 5.
¥ As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
The following tools (not included) are required
for assembly:
¥ Two (2) adjustable wrenches
¥ One (1) rubber mallet
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ Lubricant, such as grease or petroleum jelly
plus soapy water.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
Assembly
Make Things Easier for Yourself!
Everything in this manual is designed to ensure
that the assembly of our products can be completed successfully by anyone. However, it is important to recognize that your new equipment is a
sophisticated product with many small parts and
consequently, the assembly process will take
time. Most people find that by setting aside plenty
of time, and by deciding to make the task enjoyable, assembly will go smoothly.
57
54
15
53
56
56
50
50
54
53
57
6
2. Identify the Right Base Extension (33) by looking at
the indicated holes. Orient the Base Extension as
shown in the drawing. Note: See the drawing on
page 4 to identify the right and left side of the
bench.
Attach the Upright (49) and the Right Base Extension
(33) to the indicated bracket on the Tower Base (57)
with two 3/8Ó x 3 1/4Ó Bolts (32) and two 3/8Ó Jamnuts
(11). Do not tighten the Jamnuts yet.
49
32
11
57
Holes
33
3. Lubricate the inside of the Weight Carriage (23). Slide
the Weight Carriage onto the Lat Upright (34) and
lock it in the indicated position with the Carriage Pin
(38).
Attach the Lat Upright (34) and the Left Base
Extension (27) to the indicated bracket on the Tower
Base (57) with two 3/8Ó x 3 1/4Ó Bolts (32) and two
3/8Ó Jamnuts (11). Do not tighten the Jamnuts yet.
3
34
38
57
11
27
23
32
2
4. Press a 1 1/2Ó x 1 1/2Ó Outer Cap (58) onto each end
of the Stabilizer (21).
Insert two 5/16Ó x 2Ó Carriage Bolts (22) up trough the
Stabilizer (21). Note: The rubber bumpers on the
Stabilizer must be facing the floor.
Place the Stabilizer (21) on the floor next to the Seat
Base (50). Gently lift up the end of the Seat Base and
place the bracket over the 5/16Ó x 2Ó Carriage Bolts
(22) in the Stabilizer.
4
58
22
21
58
50
7
5. Press a 1 1/2Ó x 1 1/2Ó Inner Cap (7) into the end of
the Bench Frame (5). Place the bracket on the Bench
Frame over the 5/16Ó x 2Ó Carriage Bolts (22) in the
Stabilizer. Hand tighten two 5/16Ó Nylon Locknuts (15)
onto the Bolts. Do not tighten the Nylon Locknuts
yet.
See drawing 5A. Have one person hold up the end of
the Bench Frame (5) while the second person slides
the Bench Rod (8) through the indicated hole in the
Lat Upright (34) until the end of the Rod barely sticks
through the Upright.
Line up a Bench Spacer (4) with the Bench Rod (8)
and slide the Rod through the Spacer. Slide the
Bench Rod through the pre-assembled Bench Frame
Bushings (6) on the Bench Frame. Slide the Bench
Rod through the second Bench Spacer (4) and then
into the Upright (49).
Secure the end of the Bench Rod (8) going into the
Upright (49) with a 1Ó Washer (51), a 5/16Ó Washer
(53) and a Bench Rod Bolt (41).
Secure the end of the Bench Rod (8) going through
the Lat Upright (34) with a 1Ó Washer (51), a 5/16Ó
Washer (53) and a Bench Rod Bolt (41).
Go back and tighten all Locknuts and Jamnuts
5
5A
15
5
7
50
34
49
4
4
5
6
8
51
41
53
41
51
53
22
21
15
6. Attach a Backrest Bracket (2) to the Backrest (1)
with two 1/4Ó x 1/2Ó Screws (3). Make sure the
Backrest Bracket is oriented as shown (note the
position of the indicated hole). Do not tighten
the Screws yet.
6a. Refer to drawing 6a. Hold the Backrest (1) in a
vertical position as shown and slide the end of the
attached Backrest Bracket (2) onto the welded rod
on the Bench Frame (5). Hold the other Backrest
Bracket (2) at an angle as shown and slide it onto
the rod.
Refer to drawing 6b. Attach the Backrest Bracket
(2) to the Backrest (1) with two 1/4Ó x 1/2Ó Screws
(3). Note: The Screw nearest the rod should be
attached first.
Fully tighten all four 1/4Ó x 1/2Ó Screws (3) used
in steps 6 and 6a.
6a
1
6
1
3
3
2
1
3
2
5
Rod
Hole
2
6b
8
8. Press a 1 1/2Ó x 1 1/2Ó Inner Cap (7) into each end of
the Leg Lever (14).
Slide the Weight Tube (17) into the Leg Lever (14)
and secure it with a 5/16Ó x 2Ó Bolt (19) and a 5/16Ó
Nylon Locknut (15). Do not overtighten the Nylon
Locknut.
Press a 1Ó Outer Cap (18) onto the indicated end of
the Weight Tube. Press a 1Ó Inner Cap (16) into the
indicated end of the Weight Tube. Slide a Weight
Stop (55) onto the Weight Tube.
Lubricate the 3/8Ó x 2 1/4Ó Bolt (10). Attach the Leg
Lever (14) to the bracket on the Bench Frame (5) with
the Bolt and a 3/8Ó Jamnut (11). Do not overtighten
the Nylon Locknut, it must be easy to pivot the
Leg Lever.
8
14
7
55
16
17
7
15
10
19
5
18
11
7. Attach the Seat (9) to the indicated bracket on the
Bench Frame (5) with two 1/4Ó x 1/2Ó Screws (3).
7
Bracket
Lubricate
3
9. Press a 3/4Ó Inner Cap (12) into each end of the two
Pad Tubes (20).
Slide the Pad Tubes (20) into the indicated holes in
the Leg Lever (14).
Slide a Foam Pad (13) onto each end of both Pad
Tubes (20).
9
12
13
13
20
12
14
13
13
10. Locate the Cable (40). Note that one end of the Cable
has a ball and the other a closed loop.
Attach the closed loop on the Cable (40) to the bracket on the Weight Carriage (23) with a 3/8Ó x 1Ó Lat
Bolt (26), a 3/8Ó Washer (31) and a 3/8Ó Jamnut (11).
Wrap the Cable (40) around a Pulley (42) in the direction shown. Attach the Pulley and a Cable Trap (47)
to the bracket on the Lat Upright (34) with a 3/8Ó x 1
1/2Ó Pulley Bolt (46) , and a Square Nut (30). Note:
The Square Nut fits into the bracket on the Lat
Upright. It will be easier to hold the Nut with a
pair of needle nose pliers while threading the Bolt
into it. Make sure the Cable Trap is oriented as
shown.
10
47
30
42
23
11
31
26
46
34
40
9
5
Front View
Bracket
30
34
42
47
46
9
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 10 for important information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise poster to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
Adjusting the Weight Bench
USING THE LAT BAR
To use the Lat Bar (36), first remove the Support Rod (25)
and lower the Backrest (1) to the horizontal position.
Remove the Carriage Pin (38) and lower the Weight
Carriage (23) to the lowest position. Slide the desired
weights (not included) onto the weight tube on the Weight
Carriage. Attach the Lat Bar (36) to the Cable (40) with a
Cable Clip (37).
37
40
34
36
38
23
11. Wrap the Cable (40) around a Pulley (42) in the direction shown. Attach the Pulley to the Lat Upright (34)
with a 3/8Ó x 4 1/2Ó Pulley Bolt (44), a 3/8Ó Washer
(31), a Pulley Spacer (48) and a 3/8Ó Jamnut (11).
Note: Make sure the Cable is between the Pulley
and the welded pin on the Lat Upright.
Press a 3/4Ó Inner Cap (12) into each end of the
Support Rod (25)
Make sure all parts are properly tightened before
using the weight bench. The use of all remaining
parts will be explained in Adjusting the Weight
Bench beginning below.
11
44
42
48
40
11
31
34
25
12
12
ADJUSTING THE BACKREST
The Backrest (1) can be used in a level position or an
inclined position. To use the Backrest in a level position,
let the Backrest Brackets (2, not shown) rest on the
Bench Spacers (4).
To use the Backrest (1) in an inclined position, lift one
end of the Backrest. Insert the Support Rod (25) into the
holes in the Uprights (49, 34). Rotate the Support Rod
until the welded hook locks into place around the Upright
(49). Rest the Backrest Brackets (2, not shown) on the
Support Rod.
25
34
49
1
4
WARNING: Do not place more than 50 pounds on
the weight carriage. When you are using the lat bar,
always stand clear of the lat upright since the
weight carriage will swing around the upright as it
is raised. Always lower the lat bar slowly, or the
weight carriage will fall with great force.
Always disconnect the lat bar from the weight
bench when you are performing an exercise that
does not use the lat bar.
Locking
Hook
Welded Pin
10
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
The only way to increase the size and strength of
your muscles is to push them close to their maximum
capacity. When you progressively increase the intensity of your exercise, your muscles will continually
adapt and grow. You can tailor the individual exercise
to the proper intensity level in two ways:
¥ by changing the amount of weight used
¥ by changing the number of repetitions or sets per-
formed (A ÒrepetitionÓ is one complete cycle of an
exercise, such as one sit-up. A ÒsetÓ is a series of
repetitions).
The proper amount of weight for each exercise obviously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight.
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a moderate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross Training
Many people desire a complete and well-balanced fit-
ness program, and cross training is a very efficient
way to accomplish this. One example of a balanced
program is:
¥ Plan weight training workouts on Monday,
Wednesday and Friday.
¥ Plan 20 to 30 minutes of aerobic exercise, such as
cycling, running or swimming on Tuesday and
Thursday.
¥ Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exercise will reshape and strengthen your body plus
develop your heart and lungs.
PERSONALIZING YOUR EXERCISE PROGRAM
Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very important to avoid overdoing it during the first few months
of your exercise program. You should progress at
your own pace and be sensitive to your bodyÕs signals. If you experience pain or dizziness at any time
while exercising, stop immediately and begin cooling
down. Find out what is wrong before continuing.
Remember that adequate rest and a proper diet are
important factors in any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
Exercise Guidelines
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (14), slide the desired weights (not
included) onto the Weight Tube (17). Make sure the
Weight Stop (55) is mounted on the Weight Tube.
17
55
Weights
14
WARNING: Do not place more than 50 pounds on
the leg lever for normal use.
11
the most. To give balance and variety to your workouts, vary the exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise poster accompanying this manual, you will find photographs showing
the correct form for several exercises. A description of
each exercise is also provided, along with a list of the
muscles affected. Refer to the muscle chart below to
find the locations of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath!
You should rest for a short period of time after each
set. The ideal resting periods are:
¥ Rest three minutes after each set for a muscle build-
ing workout
¥ Rest one minute after each set for a toning workout
¥ Rest 30 seconds after each set for a weight loss
workout
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is very effective for increasing flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List
the date, the exercises performed, the weight plus the
numbers of sets and repetitions completed. Record
your weight and key body measurements at the end
of every month.
Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
Q. Triceps (back of arm)
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
N
O
P
Q
R
S
T
U
W
V
M
L
J
G
F
H
I
K
E
C
D
B
A
Part Identification Chart - Model No. WEBE11880
R0699A
3/8" Jam Nut (11)
5/16" Nylon Locknut (15)
5/16" Washer (53)
3/8" x 1" Lat Bolt (26)
3/8" x 1 1/2" Pulley Bolt (46)
5/16" x 2" Bolt (19)
5/16" x 2" Carriage Bolt (22)
Bench Rod Bolt (41)
Square Nut (30)
5/16" x 1 1/2" Bolt (56)
1/4 x 1/2Ó Screw (3)
3/8" x 2 1/4" Bolt (10)
3/8" x 3 1/4" Bolt (32)
3/8" x 4 1/2" Pulley Bolt (44)
3/8" Washer (31)
1" Washer (51)
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Key No. Qty. Description Key No. Qty. Description
Part List - Model No. WEBE11880
R0699A
1 1 Backrest
2 2 Backrest Bracket
3 6 1/4Ó x 1/2Ó Screw
4 2 Bench Spacer
5 1 Bench Frame
6 1 Bench Frame Bushing
7 3 1 1/2Ó x 1 1/2Ó Inner Cap
8 1 Bench Rod
9 1 Seat
10 1 3/8Ó x 2 1/4Ó Bolt
11 7 3/8Ó Jamnut
12 6 3/4Ó Inner Cap
13 4 Foam Pad
14 1 Leg Lever
15 5 5/16Ó Nylon Locknut
16 2 1Ó Inner Cap
17 1 Weight Tube
18 1 1Ó Outer Cap
19 1 5/16Ó x 2Ó Bolt
20 2 Pad Tube
21 1 Stabilizer
22 2 5/16Ó x 2Ó Carriage Bolt
23 1 Weight Carriage
24 4 Carriage Sleeve
25 1 Support Rod
26 1 3/8Ó x 1Ó Lat Bolt
27 1 Left Base Extension
28 7 Base Bumper
29 7 Bumper Screw
30 1 Square Nut
31 2 3/8Ó Washer
32 4 3/8Ó x 3 1/4Ó Bolt
33 1 Right Base Extension
34 1 Lat Upright
35 2 Handgrip
36 1 Lat Bar
37 1 Cable Clip
38 1 Carriage Pin
39 1 Carriage Pin Knob
40 1 Cable
41 2 Bench Rod Bolt
42 2 Pulley
43 1 Lat Tower Endcap
44 1 3/8Ó x 4 1/2Ó Pulley Bolt
45 3 Upright Endcap
46 1 3/8Ó x 1 1/2Ó Pulley Bolt
47 1 Cable Trap
48 1 Pulley Spacer
49 1 Upright
50 1 Seat Base
51 2 1Ó washer
52 2 1 1/2Ó x 2Ó Inner Cap
53 4 5/16Ó Washer
54 2 1/2Ó Spacer
55 1 Weight Stop
56 2 5/16Ó x 1 1/2Ó Bolt
57 1 Tower Base
58 2 1 1/2Ó x 1 1/2Ó Outer Cap
# 1 UserÕs Manual
# 1 Exercise Poster
25
11
32
34
35
40
36
37
35
11
42
44
31
46
47
42
48
30
40
26
31
11
12
12
43
45
28
29
33
28
29
11
32
27
24
24
23
20
13
12
14
1
2
2
3
8
5
6
4
7
9
10
11
3
15
21
22
58
58
3
28
29
28
29
39
38
53
52
52
49
50
51
45
41
45
28
29
28
29
12
13
18
7
15
19
16
17
7
55Ê
4
56
56
54
54
53
15
53
16
57
41
53
51
Exploded Drawing - Model No. WEBE11880
R0699A
Part No. 153351 J00206-C R0699A Printed in USA © 1999 ICON Health & Fitness, Inc.
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
1. The MODEL NUMBER of the product (WEBE11880).
2. The NAME of the product (WEIDER
¨
T28 Weight Bench).
3. The SERIAL NUMBER of the product (see the front cover of this manual).
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST on page 18 and the
EXPLODED DRAWING on page 19 of this manual).
Ordering Replacement Parts
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Limited Warranty
Loading...