Page 1
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfaction through direct assistance
from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WEBE12810
Serial No.
Write the serial number in the
space above for reference.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
Serial Number Decal (under seat)
USER’S MANUAL
Patent Pending
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Page 2
WARNING DECAL PLACEMENT
2
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
The decal shown here has been placed on the
weight bench. If the decal is missing or illegible,
please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time, to
order a free replacement decal. Apply the
replacement decal in the location shown.
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
TABLE OF CONTENTS
Page 3
3
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Keep children under the age of 12 and pets
away from the weight bench at all times.
5. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
6. Make sure all parts are properly tightened
each time you use the weight bench. Replace
any worn parts immediately.
7. Always wear athletic shoes for foot protection while exercising.
8. Make sure that the adjustment knobs are
inserted completely and tightened into the
uprights before beginning any exercise.
9. When adjusting the backrest, make sure the
adjustment tube is securely seated in the
adjustment brackets.
10. Always remove the curl post from the front
leg before performing leg curls with the leg
lever.
11. Do not use a barbell that is longer than six
feet with the weight bench. Note: The weight
bench does not include weights or a barbell.
12. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
13. Always keep an equal amount of weight on
both ends of your barbell when you are using
it. When adding or removing weights, always
keep some weight on both ends of the barbell
to prevent the barbell from tipping.
14. Keep hands and feet away from moving parts.
15. The weight bench is designed to support a
maximum of 360 pounds, including the user,
a weight bar, and weights. Do not place more
that 110 pounds, including a weight bar and
weights, on the weight rests. Do not place
more than 50 pounds on the leg lever.
16. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
17. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
IMPORTANT PRECAUTIONS
Page 4
4
Thank you for selecting the versatile WEIDER®325
weight bench. The WEIDER
®
325 is designed to be
used with your own weight set (not included) to help
you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic
increase in muscle size and strength, or a healthier
cardiovascular system, the WEIDER®325 will help you
achieve the specific results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE12810. The serial number can be
found on a decal attached to the weight bench (see
the front cover of this manual).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
Seat
Leg Lever
Weight Tube
Curl Pad
Adjustment Tube
Backrest
Weight Rests
Adjustment
Knob
BEFORE YOU BEGIN
Right Side
Left Side
Note: The terms “right side” and “left side”
are determined relative to a person sitting on
the bench; they do not correspond to what is
right and left on the drawings in the manual.
Page 5
5
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST on page 14 of this manual. Note: Some small parts may
have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
PART IDENTIFICATION CHART
M8 x 60mm Bolt (30)
M10 Nylon Locknut (11)
M8 Nylon Locknut (25)
M10 Flat Washer (29)
M6 x 62mm Screw (38)
M8 x 58mm Carriage Bolt (36)
M8 Flat Washer (10)
M6 x 16mm Screw (31)
M6 x 38mm Screw (14)
M10 x 64mm Bolt (12)
M6 Flat Washer (26)
M8 x 68mm Bolt (22)
M10 x 168mm Bolt (8)
Page 6
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two people.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Make Things Easier for Yourself
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. Most people find that by setting
aside plenty of time, assembly will go smoothly.
ASSEMBLY
6
1. Before assembling the weight bench, make sure
that you have read and understand the information in the box above.
Press a 50mm Square Inner Cap (24) into the end
of the Bench Frame (1).
Attach the Bench Frame (1) to the Front Leg (2)
using two M8 x 60mm Bolts (30), two M8 Flat
Washers (10), and two M8 Nylon Locknuts (25).
2. Insert a 50mm Square Inner Cap (24) into the Left
Base Frame (3). Attach the Left Base Frame to the
Bench Frame (1) using an M8 x 58mm Carriage
Bolt (36), an M8 x 68mm Bolt (22), and two M8
Nylon Locknuts (25). Attach the Right Base Frame
(35) in the same manner.
Attach the Left Upright (4) to the Left Base Frame
(3) with two M8 x 58mm Carriage Bolts (36) and
two M8 Nylon Locknuts (25). Attach the Right
Upright (5) to the Right Base Frame (35) in the
same manner.
1
24
1
2
30
10
10
25
25
2
5
4
24
24
25
25
35
3
36
36
22
1
Page 7
7
3. Press 2 1/2” Square Bushings (23) onto the Left
and Right Uprights (4, 5). Slide the Weight Rests
(6) into the Uprights and secure them at the desired
height with two Adjustment Knobs (27). Both
Weight Rests should be set at the same height.
3
6
6
5
4
27
23
23
27
4. Press two 38mm Square Inner Caps (32) into the
ends of the Leg Lever (9). Press a 1” Round Inner
Cap (21) into the indicated end of the weight tube.
Slide a Weight Stop (34) over the weight tube.
Press a 1” Round Angle Cap (28) onto the opposite
end of the weight tube.
Insert 3/4” Round Inner Caps (18) into the ends of
two Pad Tubes (19). Slide the Pad Tubes into the
holes at the ends of the Leg Lever (9). Slide four
Foam Pads (33) onto the ends of the Pad Tubes.
4
33
32
34
Weight
Tube
32
33
33
21
33
18
18
19
19
28
9
5. Press two 3/4” Round Inner Caps (18) into the ends
of a Pad Tube (19). Slide the Pad Tube into the
large hole in the Front Leg (2) as shown. Slide a
Foam Pad (33) onto each end of the Pad Tube.
Attach the Leg Lever (9) to the Front Leg (2) using
an M10 x 64mm Bolt (12) and an M10 Nylon
Locknut (11). Do not overtighten the Nylon
Locknut; the Leg Lever must be able to pivot
freely.
5
33
33
12
9
11
18
19
2
Page 8
8
6. Press 1” Square Inner Caps (7) into the ends of
both Backrest Tubes (20). Lubricate the M10 x
168mm Bolt (8). Attach the Backrest Tubes to the
Bench Frame (1) with the Bolt, two M10 Flat
Washers (29), and an M10 Nylon Locknut (11). Do
not overtighten the Nylon Locknut; the Backrest
Tubes must be able to pivot freely.
Press two 25.4mm x 38.1mm Square Inner Caps
(39) into the Adjustment Tube (37). Slide the
Adjustment Tube into the adjustment brackets on
the Uprights (4, 5) with the pins on the Adjustment
Tube facing downward.
7. Attach the Seat (16) to the Bench Frame (1) using
two M6 x 16mm Screws (31), an M6 x 62mm Screw
(38), and an M6 Flat Washer (26).
6
7
8
29
29
1
11
39
Pin
Bracket
39
37
4
5
7
16
31
1
38
26
7
20
8. Attach the Backrest (15) to the Backrest Tubes (20)
using four M6 x 38mm Screws (14) and four M6
Flat Washers (26).
Make sure that the Backrest (15) is oriented so
that there is a gap between the Backrest and the
Seat (16).
8
26
20
15
16
14
14
26
9
9. Attach the Curl Pad (17) to the Curl Post (13) using
two M6 x 16mm Screws (31).
10. Make sure all parts of the weight bench are
properly tightened. The use of all remaining
parts will be explained in ADJUSTMENTS, beginning on the following page.
17
13
31
Page 9
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information
and refer to the accompanying exercise guide to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
9
ADJUSTING THE BACKREST
The Backrest (15) can be set to three different positions: a level position, a decline position, and an incline
position.
To change the position of the Backrest (15), move the
Adjustment Tube (37) to a different set of adjustment
brackets on the Uprights (4, 5).
Make sure that the Adjustment Tube (37) is securely
seated in the adjustment brackets.
15
Brackets
5
4
37
ADJUSTMENTS
15
FOLDING THE BACKREST
To perform squat exercises, you will need to fold the
Backrest (15) to the upright position.
To fold the Backrest (15), lift and pull it forward as far
as it will go. It will be held in place by its own weight.
WARNING: Always fold the
Backrest (15) out of the way when performing
squat exercises. Do not sit on the seat when the
Backrest is folded.
Always place 50 pounds on the leg lever to
balance the bench when performing squat exercises.
Do not stand with your back to the weight
bench when performing squat exercises. You
should be able to see the weight rests while
exercising so that you can safely return the barbell when you finish the exercise.
Page 10
10
ATTACHING WEIGHTS TO THE LEG LEVER
To use the the Leg Lever (9), slide the desired amount
of weight (not included) onto the weight tube on the Leg
Lever.
WARNING: Do not place more than
50 pounds on the Leg Lever (9).
9
Weight
Tube
ADJUSTING THE WEIGHT RESTS
To change the height of the Weight Rests (6), remove
your barbell from the Weight Rests. Then, remove
the Adjustment Knobs (27) from both Uprights (4, 5).
Position the Weight Rests at the desired height, so that
the holes in the Weight Rests and the Uprights are
aligned. Fully tighten the Adjustment Knobs into the
Weight Rests and the Uprights.
WARNING: Always set both Weight
Rests (6) at the same height. The Adjustment
Knobs (27) must be inserted through the Weight
Rests and the Uprights (4, 5) and be firmly tightened. Never tighten an Adjustment Knob into an
Upright before inserting the Weight Rest.
6
6
27
27
5
4
ATTACHING THE CURL POST
For some exercises, the Curl Post (13) must be
attached to the weight bench.
Insert the Curl Post (13) into the indicated hole in the
Front Leg (2). Align the holes in the Front Leg and the
Curl Post. Secure the Curl Post with an Adjustment
Knob (27). Make sure that you fully tighten the
Adjustment Knob.
27
13
2
Page 11
11
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your
muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You
can adjust the intensity level of an individual exercise
in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is
right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight.
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a moderate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross Training
Cross training is an efficient way to get a complete
and well-balanced fitness program. An example of a
balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exercise will reshape and strengthen your body, plus
develop your heart and lungs.
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed, is an individual matter. It is important to avoid
overdoing it during the first few months of your exercise program. You should progress at your own pace
and be sensitive to your body’s signals. If you experience pain or dizziness at any time while exercising,
stop immediately and begin cooling down. Find out
what is wrong before continuing. Remember that adequate rest and a proper diet are important factors in
any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise,
and moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
12 to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
Page 12
12
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning work-
out.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. The
chart on page 13 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the weight used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. The key to achieving the
greatest results is to make exercise a regular and
enjoyable part of your everyday life.
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
Q. Triceps (back of arm)
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
A
B
C
D
E
G
H
I
J
K
F
M
L
T
N
O
P
Q
R
S
U
V
W
Page 13
13
MONDAY
Date:
/ /
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
AEROBIC EXERCISE
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
FRIDAY
Date:
/ /
Make photocopies of this page for scheduling and recording your workouts.
Page 14
14
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
1 1 Bench Frame
2 1 Front Leg
3 1 Left Base Frame
4 1 Left Upright
5 1 Right Upright
6 2 Weight Rest
7 4 1” Square Inner Cap
8 1 M10 x 168mm Bolt
9 1 Leg Lever
10 2 M8 Flat Washer
11 2 M10 Nylon Locknut
12 1 M10 x 64mm Bolt
13 1 Curl Post
14 4 M6 x 38mm Screw
15 1 Backrest
16 1 Seat
17 1 Curl Pad
18 6 3/4” Round Inner Cap
19 3 Pad Tube
20 2 Backrest Tube
21 1 1” Round Inner Cap
22 2 M8 x 68mm Bolt
23 2 2 1/2” Square Bushing
24 3 50mm Square Inner Cap
25 10 M8 Nylon Locknut
26 5 M6 Flat Washer
27 3 Adjustment Knob
28 1 1” Round Angle Cap
29 2 M10 Flat Washer
30 2 M8 x 60mm Bolt
31 4 M6 x 16mm Screw
32 2 38mm Square Inner Cap
33 6 Foam Pad
34 1 Weight Stop
35 1 Right Base Frame
36 6 M8 x 58mm Carriage Bolt
37 1 Adjustment Tube
38 1 M6 x 62mm Screw
39 2 25.4mm x 38.1mm Square Inner
Cap
# 1 User’s Manual
# 1 Exercise Guide
Key No. Qty. Description Key No. Qty. Description
PART LIST—Model No. WEBE12810 R0701A
Page 15
15
EXPLODED DRAWING—Model No. WEBE12810 R0701A
39
33
32
34
21
9
32
33
18
11
30
10
28
18
19
13
19
10
17
18
12
35
36
2
18
31
27
25
6
23
18
5
19
25
31
33
36
18
25
25
24
33
27
25
1
26
38
31
11
29
22
7
24
14
36
25
16
29
25
20
37
15
8
14
26
3
2626
14
39
6
27
23
7
7
4
25
25
24
36
Page 16
Part No. 177212 R0701A Printed in China © 2001 ICON Health & Fitness, Inc.
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WEBE12810)
• The NAME of the product (WEIDER
®
325 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING on pages 14 and 15 of this manual).
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
LIMITED WARRANTY
ORDERING REPLACEMENT PARTS
Loading...