W box technologies 0E-13BF36, 0E-40D28WDR, 0E-13D28, 0E-21D28WDR, 0E-40BF36WDR User Manual
...
High-Resolution IR Camera
User Manual
If you have any questions, please call
W Box Tech Support 1-833-574-9124
for assistance.
E-mail：tech@wboxsupport.com
0E-13D28
0E-13BF36
0E-21D28WDR
0E-21BF36WDR
0E-40D28WDR
0E-40BF36WDR
High-Resolution IR Camera
User Manual
Hardware Connection
Issue V1.0 (2018-05-11) i
Precautions
Symbol
Description
It alerts you to fatal dangers which, if not avoided, may
cause deaths or severe injuries.
It alerts you to moderate dangers which, if not avoided,
may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may cause
device damage, data loss, device performance
deterioration, or unpredictable results.
It provides a tip that may help you resolve problems or
save time.
It provides additional information.
Fully understand this document before using this device, and strictly observe rules in
this document when using this device. If you install this device in public places,
provide the tip "You have entered the area of electronic surveillance" in an eyecatching place. Failure to correctly use electrical products may cause fire and severe
injuries. To prevent accidents, carefully read the following context:
Symbols
This document may contain the following symbols whose meanings are described
accordingly.
Precautions
To prevent electric shocks or other dangers, keep power plugs dry and clean.
Strictly observe installation requirements when installing the device. The
manufacturer shall not be held responsible for device damage caused by users' nonconformance to these requirements.
Hardware Connection
High-Resolution IR Camera
User Manual
ii Issue V1.0 (2018-05-11)
Strictly conform to local electrical safety standards and use power adapters that are
marked with the LPS standard when installing and using this device. Otherwise,
this device may be damaged.
Use accessories delivered with this device. The voltage must meet input voltage
requirements for this device.
If this device is installed in places with unsteady voltage, ground this device to
discharge high energy such as electrical surges in order to prevent the power supply
from burning out.
When this device is in use, ensure that no water or any liquid flows into the device.
If water or liquid unexpectedly flows into the device, immediately power off the
device and disconnect all cables (such as power cables and network cables) from
this device.
Do not focus strong light (such as lighted bulbs or sunlight) on this device.
Otherwise, the service life of the image sensor may be shortened.
If this device is installed in places where thunder and lightning frequently occur,
ground the device nearby to discharge high energy such as thunder strikes in order
to prevent device damage.
Avoid heavy loads, intensive shakes, and soaking to prevent damages during
transportation and storage. The warranty does not cover any device damage that is
caused during secondary packaging and transportation after the original packaging
is taken apart.
Protect this device from fall-down and intensive strikes, keep the device away from
magnetic field interference, and do not install the device in places with shaking
surfaces or under shocks.
Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight
neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
Do not jam the ventilation opening. Follow the installation instructions provided in
this document when installing the device.
Keep the device away from heat sources such as radiators, electric heaters, or other
heat equipment.
Keep the device away from moist, dusty, extremely hot or cold places, or places
with strong electric radiation.
If the device is installed outdoors, take insect- and moisture-proof measures to
avoid circuit board corrosion that can affect monitoring.
Remove the power plug if the device is idle for a long time.
Before unpacking, check whether the fragile sticker is damaged. If the fragile
sticker is damaged, contact customer services or sales personnel. The manufacturer
shall not be held responsible for any artificial damage of the fragile sticker.
High-Resolution IR Camera
User Manual
Hardware Connection
Issue V1.0 (2018-05-11) iii
Special Announcement
All complete products sold by the manufacturer are delivered along with nameplates,
operation instructions, and accessories after strict inspection. The manufacturer shall
not be held responsible for counterfeit products.
This manual may contain misprints, technology information that is not accurate enough,
or product function and operation description that is slightly inconsistent with the
actual product. The manufacturer will update this manual according to product function
enhancement or changes and regularly update the software and hardware described in
this manual. Update information will be added to new versions of this manual without
prior notice.
This manual is only for reference and does not ensure that the information is totally
consistent with the actual product. For consistency, see the actual product.
Hardware Connection
High-Resolution IR Camera
User Manual
iv Issue V1.0 (2018-05-11)
Contents
1 Hardware Connection ............................................................................................. 6
2 Eyeball Camera......................................................................................................... 7
2.1 Dimensions ..................................................................................................................... 7
2.2 Device Installation .......................................................................................................... 7
3 Bullet camera .......................................................................................................... 11
3.1 Dimensions .................................................................................................................... 11
3.2 Device Installation ........................................................................................................ 12
4 Web Operation ....................................................................................................... 15
4.1 Quick start .................................................................................................................... 15
4.1.1 Login and Logout ............................................................................................. 15
4.1.2 Changing the Password .................................................................................... 16
4.1.3 Main Page Layout ............................................................................................ 17
4.2 Browsing Real-Time Videos ......................................................................................... 19
4.3 Configuring the Device ................................................................................................ 21
4.3.1 Configuring the Device Information ................................................................ 21
4.4 Setting Video and Audio Stream Parameters ................................................................ 23
4.4.2 Setting SVC Stream Parameters ....................................................................... 27
4.4.3 Region of Interest ............................................................................................. 28
4.4.4 Setting Local Network Parameters ................................................................... 30
4.4.5 Configuring Device Ports ................................................................................. 33
4.4.6 Configuring the Date and Time ........................................................................ 34
4.4.7 Setting the Channel Name, Video System, and Source Resolution .................. 37
4.4.8 Setting OSD Parameters ................................................................................... 38
4.4.9 System Service ................................................................................................. 41
4.5 Configuring the Alarm Function................................................................................... 42
4.5.1 Setting Disk Alarm Parameters ........................................................................ 42
4.5.2 Setting Network Alarm Parameters .................................................................. 42
4.5.3 Setting Motion Alarm Parameters .................................................................... 43
4.5.4 Setting push message Parameters ..................................................................... 45
4.6 Configuring the Recording Function ............................................................................ 46
4.6.1 Configuring a Recording Policy ....................................................................... 46
High-Resolution IR Camera
User Manual
Hardware Connection
Issue V1.0 (2018-05-11) v
4.6.2 Configuring a Recording Directory .................................................................. 48
4.6.3 Configuring the SD Card or NAS Recording ................................................... 50
4.7 Configuring the Privacy Mask Function ....................................................................... 51
4.8 Configuring the Network Service ................................................................................. 53
4.8.1 Setting 802.1x Parameters ................................................................................ 53
4.8.2 Setting DDNS Parameters ................................................................................ 54
4.8.3 Setting PPPoE Parameters ................................................................................ 55
4.8.4 Setting Port Mapping Parameters ..................................................................... 56
4.8.5 Setting SMTP Parameters ................................................................................ 58
4.8.6 Setting FTP Parameters .................................................................................... 60
4.8.7 Setting IP Filter Parameters .............................................................................. 62
4.8.8 Setting CGI Alarm Service Center Parameters ................................................. 65
4.8.9 Setting SNMP Parameters ................................................................................ 68
4.9 Privilege Manager ........................................................................................................ 71
4.10 Configuring Protocol Parameters ............................................................................... 75
4.10.1 Checking Protocol Information ...................................................................... 75
4.10.2 Setting Security Authentication ...................................................................... 75
4.10.3 Setting Multicast Parameters .......................................................................... 76
4.11 Querying Operation Logs ........................................................................................... 78
4.11.2 Querying Operation Logs ............................................................................... 78
4.11.3 Querying Alarm Logs ..................................................................................... 79
4.11.4 Reporting Logs ............................................................................................... 81
4.12 Maintaining the Device .............................................................................................. 81
4.12.1 Restarting a Device ........................................................................................ 81
4.12.2 Updating the software package ...................................................................... 82
4.12.3 Restoring a Device to Factory Settings .......................................................... 83
4.13 Local Configuration ................................................................................................... 83
5 Technical Specifications ....................................................................................... 85
Hardware Connection
High-Resolution IR Camera
User Manual
6
Issue V1.0 (2018-05-11)
1 Hardware Connection
ID
Core
Description
1
Network access port
Connects to a standard Ethernet cable.
2
Power supply (DC 12V)
Connects to a 12V(-15%-+10% ) direct current
(DC) power supply.
Figure 1-1 shows the power and network cables.
Figure 1-1 Power and network cables
Table 1-1 shows the description of the cable.
Table 1-1 description of the cable
High-Resolution IR Camera
User Manual
Eyeball Camera
Issue V1.0 (2018-05-11) 7
2.1 Dimensions
Figure 2-1 shows the camera dimensions of 0E-13D28 and 0E-21D28WDR.
Figure 2-1 Dimensions of 0E-13D28 and 0E-21D28WDR (unit: mm)
Figure 2-2 shows the camera dimensions of 0E-40D28WDR.
2 Eyeball Camera
Figure 2-2 Dimensions of 0E-40D28WDR (unit: mm)
2.2 Device Installation
Step 1 Open a package, take out the camera, unscrew the camera compression ring, and
disassemble the camera, the camera components is shown in Figure 2-3.
Eyeball Camera
High-Resolution IR Camera
User Manual
8
Issue V1.0 (2018-05-11)
Figure 2-3 Camera components
Step 2 Use the base as drill template, drill holes on the ceiling or wall, and reserve the cable
entries of the video/power cables.
Figure 2-4 and Figure 2-5 shows the dimensions of the camera mounting base.
Figure 2-4 Dimensions of the 0E-HDD1MP28 and 0E-HDD2MP28 mounting base
High-Resolution IR Camera
User Manual
Eyeball Camera
Issue V1.0 (2018-05-11) 9
Figure 2-5 Dimensions of the 0E-HDDMO2812 mounting base
Step 3 Nail swell plastic buttons in to drilled holes, and fix the camera mounting base to the
ceiling (or wall) by use of self-tapping screws.
Step 4 Install the compression ring, the dome shell, and the dome shell fixed base on the
camera mounting base.
Figure 2-6 shows camera installation.
Figure 2-6 Camera installation
Step 5 Turn the main body, adjust the lens direction, and note the position of the dome cover
window.
Eyeball Camera
High-Resolution IR Camera
User Manual
10
Issue V1.0 (2018-05-11)
Connect the BNC connector of the power or video cable to a video signal cable and
connect the other connector to a low-voltage power cable. After installing the camera,
directly connect the video cable and power cable.
Adjust the position of the camera by triaxial rotation: rotating horizontally, rotating up
and down, and performing lens axial rotation, and adjust the camera direction and lens
alignment target.
Figure 2-7 shows monitoring direction adjustment.
Figure 2-7 Monitoring direction adjustment
Step 6 Use soft cloth to wipe the lens front glass which is likely to be soiled due to installation
for cleaning the camera, and complete product installation and debugging.
----End
High-Resolution IR Camera
User Manual
Bullet camera
Issue V1.0 (2018-05-11) 11
3.1 Dimensions
Figure 3-1 shows the dimensions of 0E-40BF36WDR.
Figure 3-1 dimensions of 0E-40BF36WDR
3 Bullet camera
Figure 3-2 shows the dimensions of 0E-13BF36 and 0E-21BF36WDR.
Bullet camera
High-Resolution IR Camera
User Manual
12
Issue V1.0 (2018-05-11)
Figure 3-2 dimensions of 0E-13BF36 and 0E-21BF36WDR
3.2 Device Installation
Step 1 Stick the Installation location sticker on the ceiling or wall, Drill three holes based on
the marks on the sticker. Drive the swell plastic buttons into the holes, as shown in
Figure 3-3.
Figure 3-3 Drilling holes
Step 2 Loosen the locking screw with L-Hex Wrench and rotate the camera, then attach the
camera to the surface, as shown in Figure 3-4.
High-Resolution IR Camera
User Manual
Bullet camera
Issue V1.0 (2018-05-11) 13
Figure 3-4 Installing camera
Step 3 Connect the Power and video cable, as shown in Figure 3-5.
Figure 3-5 Connecting cable
Step 4 Loosen the locking screw with L-Hex Wrench, rotate the camera to adjust the position
and image so that the camera faces the monitored area, then tighten the locking screw,
as shown in Figure 3-6.
To rotate the part 1 of the camera for 360°, loosen rotation lock.
To rotate the part 2 of the camera for180°, loosen screw 1.
To rotate the part 3 of the camera for 360°, loosen screw 2.
Bullet camera
High-Resolution IR Camera
User Manual
14
Issue V1.0 (2018-05-11)
Figure 3-6 Adjusting monitored area
----End
High-Resolution IR Camera
User Manual
Web Operation
Issue V1.0 (2018-05-11) 15
4 Web Operation
4.1 Quick start
4.1.1 Login and Logout
You must use Internet Explorer 7, and more to access the web management system;
otherwise, some functions may be unavailable.
Login
Step 1 Open Internet Explorer, enter the IP address of the IP camera (default value:
192.168.1.64) in the address box, and press Enter.
The login page is displayed, as shown in Figure 4-1.
Figure 4-1 Login page
Step 2 Enter the user name, and password.
Web Operation
High-Resolution IR Camera
User Manual
16
Issue V1.0 (2018-05-11)
The default user name is admin. The default password is admin.
Change the password to ensure system security.
You can change the system display language on the login page.
Step 3 Click .
The main page is displayed.
----End
Logout
To log out of the system, click in the upper right corner of the main page. The
login page is displayed after you log out of the system.
4.1.2 Changing the Password
Description
The change password page will be displayed as shown in Figure 4-2, when you login
the system for the first time.
Figure 4-2 Change the default password page
Or click to change the password for login the system, as show in Figure 4-3.
High-Resolution IR Camera
User Manual
Web Operation
Issue V1.0 (2018-05-11) 17
Figure 4-3 Change the password page
Step 1 Enter the old password, new password, and confirmation password.
Step 2 Click OK.
If the message "Change password success" is displayed, the password is successfully
changed. If the password fails to be changed, the cause is displayed. (For example, the
new password length couldn’t be less than eight.)
Step 3 Click OK.
The login page is displayed.
4.1.3 Main Page Layout
On the main page, you can view real-time videos, receive alarm and fault notifications,
set parameters, change the password, and log out of the system. Figure 4-4 shows the
main page layout. Table 4-1 describes the elements on the main page.
Web Operation
High-Resolution IR Camera
User Manual
18
Issue V1.0 (2018-05-11)
Figure 4-4 Main page layout
No.
Element
Description
1
Real-time video
area
Real-time videos are played in this area. You can also set
sensor parameters.
2
Playback
You can query the playback videos in this area.
NOTE
Only when the SD card or NAS have videos that you can
query the playback videos.
3
Device
configuration
You can choose a menu to set device parameters,
including the device information, audio and video
streams, alarm setting, and privacy mask function.
4
Alarm icon
When the device generates an alarm, the alarm icon
is displayed. You can click the icon to view the alarm
information.
NOTE
When the device accepts an alarm signal, the alarm icon will
display within 10s in the web management system.
Table 4-1 Elements on the main page
High-Resolution IR Camera
User Manual
Web Operation
Issue V1.0 (2018-05-11) 19
5
Fault icon
When the device encounters an exception, the fault icon
is displayed.
You can click the icon to view the fault information.
6
Change password
You can click to change the password.
7
Sign Out
You can click to return to the login page.
----End
4.2 Browsing Real-Time Videos
You can browse real-time videos in the web management system.
Preparation
You will be prompted with a message ”download and install the new plugin” as shown
in Figure 4-5 when you log in to the web management system for the first time:
Figure 4-5 Download the plug-ins page
Step 1 Click “ download and install the new plugin”, download and setup the plug-ins and
the install the plugin following the prompt.
Step 2 Reopen the browser after installing.
If the repair tips displayed when installing the control , please ignore the prompt, and
continue the installation.
Web Operation
High-Resolution IR Camera
User Manual
20
Issue V1.0 (2018-05-11)
----End
Description
To browse real-time videos, click Live Video. The Live Video page is displayed, as
shown in Figure 4-6.
Figure 4-6 Live Video page
On the Live Video page, you can perform the following operations:
Click to stop playing a video.
Click to play a video.
Double-click in the video area to enter the full-screen mode, and double-click again
to exit.
Switch among preset streams 1, 2, and 3. For details about how to configure
streams, see
Setting Video and Audio Stream Parameters.
Click to snapshot and save the photos.
High-Resolution IR Camera
User Manual
Web Operation
Issue V1.0 (2018-05-11) 21
Configure the sensor.
You can right-click in the video area. A shortcut menu is displayed and allows you
to enter the full-screen mode, set sensor parameters, zoom in or out, and return to
the default view.
To set sensor parameters, click to open the Sensor Setting page. On the
Sensor Setting page, you can adjust the time segment, image, scene, exposure,
white balance, focus setting, Iris setting, white balance, and noise filter as prompted.
4.3 Configuring the Device
4.3.1 Configuring the Device Information
Description
The device information includes:
Device ID, name, type, model, and MAC address.
Hardware and software versions.
Number of video channels, number of alarm input channels, number of alarm
output channels, and number of serial ports.
You can modify the device name. All other parameters can only be viewed.
When the device is upgraded, the device information is updated automatically.
Procedure
Step 1 Click Configuration > Device Info.
The Device Info page is displayed, as shown in Figure 4-7.
Web Operation
High-Resolution IR Camera
User Manual
22
Issue V1.0 (2018-05-11)
Figure 4-7 Device Info page
Parameter
Description
Setting
Device ID
Unique device identifier used by the
platform to distinguish the devices.
[Setting method]
These parameters
cannot be modified.
Device Name
Name of the device.
NOTE
The device name cannot exceed 32
bytes or 10 simplified characters;
otherwise, the modification fails.
[Setting method]
Enter a value
manually.
MAC Address
N/A
[Setting method]
These parameters
cannot be modified.
Camera Type
Product Model
Manufacturer Name
Step 2 View the device information, set the device ID and name according to Table 4-2.
Table 4-2 Device parameters
High-Resolution IR Camera
User Manual
Web Operation
Issue V1.0 (2018-05-11) 23
Parameter
Description
Setting
Hardware Version
Firmware Version
Video Channel(s)
Channel Quantity
Alarm Input Quantity
Alarm Output Quantity
Serial Port Quantity
Network card Quantity
Step 3 Click .
If the message "Apply success!" is displayed, click OK. The system saves the
settings.
If the message "Apply failed!" is displayed, you must apply for the Parameter
Configure permission from an administrator. For details, see 4.10.1
4.4 Setting Video and Audio Stream Parameters
Procedure
Step 1 Click Configuration > Stream > Base Stream.
The Stream Configuration page is displayed, as shown in Figure 4-8.
Web Operation
High-Resolution IR Camera
User Manual
24
Issue V1.0 (2018-05-11)
Figure 4-8 Stream Configuration page
Parameter
Description
Setting
Stream ID
The device supports 3 streams.
Streams 1 and 2 use the H.264 codec.
The maximum resolution can be set
for streams 1.
[Setting method]
Select a value from the
drop-down list box.
Name
Stream name.
NOTE
The stream name is combined with
Chinese character, number, character and
underline.
[Setting method]
Enter a value manually.
The value cannot
exceed 32 bytes.
[Default value]
stream1
Step 2 Set the parameters according to Table 4-3.
Table 4-3 Stream configuration parameters
High-Resolution IR Camera
User Manual
Web Operation
Issue V1.0 (2018-05-11) 25
Parameter
Description
Setting
Video Encode
Type
The video codec determines the image
quality and network bandwidth required
by a video. Currently, the following
codec standards are supported:
MJPEG
MJPEG is a standard intra-frame
compression codec. The compressed
image quality is good. No mosaic is
displayed on motion images. MJPEG
does not support proportional
compression and requires large storage
space. Recording and network
transmission occupy large hard disk
space and bandwidth. MJPEG is not
applicable to continuous recording for a
long period of time or network
transmission of videos. It can be used to
send alarm images.
H.264
H.264 consists of H.264 Base Profile,
H.264 Main Profile, and H.264 High
profile. The performance of H.264 High
Profile is higher than that of H.264
Main Profile, and the performance of
H.264 Main Profile is higher than that
of H.264 Base Profile. If a hardware
decoding device is used, select the
appropriate codec based on the decoding
performance of the device.
H.264 High Profile has the highest
requirements on the hardware
performance, and H.264 Base Profile
has the lowest requirements on the
hardware performance.
H.265
H.265 is the new video encoding
standard ,it's the improvement standard
from H.264. H.265 improves the
streams, encoding quality and algorithm
complexity to make configuration as
optimization.
[Setting method]
Select a value from the
drop-down list box.
[Default value]
H.264
NOTE
The H.264 High Profile
codec means high
requirements on the
hardware. If the hard
decoding capability is
low, use H.264 Main
Profile or H.264 Base
Profile.
Audio Encode
Type
The following audio codec standards are
supported:
[Setting method]
Select a value from the
Web Operation
High-Resolution IR Camera
User Manual
26
Issue V1.0 (2018-05-11)
Parameter
Description
Setting
G711_ULAW: mainly used in North
America and Japan.
G711_ALAW: mainly used in Europe
and other areas.
RAW_PCM: codec of the original
audio data. This codec is often used
for platform data.
drop-down list box.
Resolution
A higher resolution means better image
quality.
NOTE
IP cameras support the different
resolutions based on the model.
[Setting method]
Select a value from the
drop-down list box.
Frame
Rate(fps)
The frame rate is used to measure
displayed frames. A higher frame rate
means smoother videos. A video whose
frame rate is higher than 22.5 f/s is
considered as smooth by human eyes.
Frame rates for different frequencies are
as follows:
50 Hz: 1–25 f/s
60 Hz: 1–30 f/s
NOTE
The frequency is set on the Device
Configuration > Camera page. The
biggest MJPEG coding format frame rate
is 12 frames per second.
[Setting method]
Select a value from the
drop-down list box.
I Frame
Interval(Unit:Fr
ame)
I frames do not require other frames to
decode.
A smaller I frame interval means better
video quality but higher bandwidth.
[Setting method]
Select a value from the
drop-down list box.
Bit Rate Type
The bit rate is the number of bits
transmitted per unit of time.
The following bit rate types are
supported:
Constant bit rate (CBR)
The compression speed is fast; however,
improper bit rate may cause vague
motion images.
Variable bit rate (VBR)
[Setting method]
Select a value from the
drop-down list box.
Loading...