Watts U5B-Z3 User Manual
For Residential and Commercial Applications
ES-U5B
Job Name
–––––––––––––––––––––––––––––––––––––––––––
Contractor
––––––––––––––––––––––––––––––––––––––––––––
Job Location
–––––––––––––––––––––––––––––––––––––––––
Approval
–––––––––––––––––––––––––––––––––––––––––––––
Engineer
–––––––––––––––––––––––––––––––––––––––––––––
Contractor’s P.O. No.
–––––––––––––––––––––––––––––––––––
Approval
–––––––––––––––––––––––––––––––––––––––––––––
Representative
––––––––––––––––––––––––––––––––––––––––
Series U5B
Water Pressure Reducing Valves*
Sizes: 1⁄2" – 2" (15 – 50mm)
Series U5B Water Pressure Reducing Valves are designed to reduce incoming water pressure to a sensible level to protect plumbing system components and reduce water consumption. This series is suitable for
water supply pressures up to 300psi (20.7 bar) and may be adjusted from
25 – 75psi (172 – 517 kPa). The standard setting is 50psi (345 kPa). All
parts are quickly and easily serviceable without removing the valve from the
line. The U5B’s standard bypass feature permits the flow of water back
through the valve into the main when pressures, due to thermal expansion
on the outlet side of the valve, exceed the pressure in the main supply.
Features
• Standard construction includes Z3 sealed spring cage and stainless steel
corrosion resistant adjusting cage screws for accessable outdoor
or
pit installations
• Integral stainless steel strainer
• Replaceable seat module
• Bronze body construction
• Serviceable in line
• Bypass feature controls thermal expansion pressure (U5B-Z3)**
• High temperature resistant reinforced diaphragm for hot water
Models
U5B-Z3 NPT threaded female union inlet x NPT female outlet w/built in
thermal expansion bypass
U5B-S-Z3 Solder union inlet x NPT female outlet w/built in thermal
expansion bypass
5M3-Z6 Water meter threaded connections and 71⁄2" (190mm) lay
length for new or existing meter box installations. For
5
⁄8"
(16mm),
5
⁄8" x 3⁄4" (16 x 20mm) or 3⁄4" (20mm) meter
setters or resetters
U5B-QC-Z3 Quick-Connect Single-Union – Inlet end
Specifications
Standard Specifications: A Water Pressure Reducing Valve with integral
strainer shall be installed in the water service pipe near its entrance to the
building where supply main pressure exceeds 60psi (413 kPa) to reduce it
to 50psi (345 kPa) or lower. The valve shall feature a bronze body suitable
for water supply pressures up to 300psi (20.7 bar). Provision shall be made
to permit the bypass flow of water back through the valve into the main
when pressures, due to thermal expansion on the outlet side of the valve,
exceed the pressure in the main supply. Water Pressure Reducing Valve
with built-in bypass check valves will be acceptable. Approved valve shall
be listed to ASSE 1003 and IAPMO and certified to CSA B356. Valve shall be
a Watts Regulator Company Series U5B-Z3.
* A water saving test program concluded that reducing the supply pressure
from 80-50psi (551-345 kPa) resulted in a water savings of 30%.
** Note: The bypass feature will not prevent the pressure relief valve from opening
on the hot water supply system with pressure above 150psi (10.3 bar).
U5B-Z3
Sensitive spring and large diaphragm
area provide for accurate pressure
control and wide range of adjustment.
High temperature resisting
diaphragm for hot or cold water.
Bronze body construction
Stainless steel seat
Large integral
stainless steel
strainer screen
easily removed
for cleaning.
Disc holder removable
for replacement of disc
without dismantling
the valve - no special
tools required.
Suffix B Bypass feature
Spring (not shown)
“LP” Model only
Expanded
Pressure
Initial
Pressure
Reduced
Pressure
Inlet Seat and Disc
Suffix B
Thermal Expansion Bypass Check Valve Feature
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials
without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
Materials
Body: Bronze
Seat: Replaceable stainless steel
Integral Strainer: Stainless steel
Diaphragm: Reinforced EPDM
Valve Disc: EPDM
Note: for LP models where application temperatures exceed 160°F (71°C),
but not over 180°F (82°C), a Teflon
®
protector should be added to
sizes 1
1
⁄4" – 2" (32 – 50mm).
5M3-Z6 model provided with cast iron spring cage
Pressure – Temperature
Temperature Range: 33°F – 160°F (0.5°C – 71°C)
Maximum Working Pressure: 300psi (20.7 bar)
Adjustable Reduced Pressure Range: 25 – 75psi (172 – 517 kPa)
Standard Reduced Pressure Setting: 50psi (345 kPa)
Options
Add Suffix
G Gauge tapping
GG Gauge tapping and 160psi (11 bar) gauge
HP High pressure range 75 – 100psi (5.2 – 6.9 bar)
LP Low pressure range 10 – 35psi (69 – 241 kPa)
Standards
Meets requirements of ASSE Standard 1003; (ANSI A112.26.2); CSA
Standard B356; Southern Standard Plumbing Code and listed by IAPMO.
Teflon
®
is a registered trademark of the E.I. Dupont de Nemours & Company.
Capacity
MODEL SIZE (DN) DIMENSIONS WEIGHT
AA
1 CDGEtEsEQC FQC F *
in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kgs.
U5B-Z31⁄2 15 55⁄8 142.8 51⁄2 139.7 57⁄8 149.2 15⁄8 41.2 31⁄16 77.77⁄16 11.11⁄2 12.7 17⁄16 36 11⁄2 38 101⁄4 260.3 4 1.8
3
⁄4 20 63⁄16 157.1 61⁄4 158.7 67⁄8 174.6 17⁄8 47.6 31⁄2 88.91⁄2 12.73⁄4 19 19⁄16 40 111⁄16 42 111⁄2 292.1 5 2.3
125 65⁄8 168.2 63⁄4 171.4 73⁄8 187.3 2 50.8 4 101.69⁄16 14.27⁄8 22.2 111⁄16 43 13⁄4 45 121⁄8 307.9 6 2.7
11⁄4 32 715⁄16 190.5 711⁄16 195.2 83⁄8 212.7 21⁄4 57.1 41⁄2 113.35⁄8 15.8 1 25.4 133⁄8 339.7 9.4 4.3
11⁄2 40 97⁄16 239.7 93⁄4 247.6 93⁄8 238.1 27⁄8 73 43⁄4 120.65⁄8 15.8 11⁄8 28.5 15 381.0 14.4 6.5
250 107⁄8 276.2 111⁄2 292.1 121⁄4 311.1 31⁄4 82.5 6 152.45⁄8 15.8 13⁄8 34.9 181⁄4 463.5 23 10.4
* Dimension includes optional gauge
G
C (Max)
D
F* (Max)
A1
A
Es
Et
A - U5B-Z3
A1 - U5B-S-Z3
ET - NPT Engagement for tight joint
ES - Female sweat socket depth
EQC- Quick-Connect
EQC
FQC
kPa psi
172 25
138 20
103 15
69 10
34 5
00
kPa psi
172 25
138 20
103 15
69 10
34 5
00
10 30 50 70 90 110 gpm
38 114 190 266 342 418 lpm
0 10 20 30 40 50 gpm
0 38 76 114 152 190 lpm
Sizes 1⁄2", 3⁄4", 1" (15, 20, 25mm)
Reduced Pressure Fall-off
Reduced Pressure Fall-off
Sizes 11⁄4", 11⁄2", 2" (32, 40, 50mm)
1
⁄2"
3
⁄4"
1"
2"
11⁄2"
11⁄4"
Dimensions - Weights
ES-U5B 0948 © 2009 Watts
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
A Watts Water Technologies Company
Loading...