Waring WDM360 User Manual [en, es, fr]

WDM360

Triple spindle drink mixer

malTeadora con Tres agiTadores

shaker à 3 agiTaTeurs

For your safety and continued enjoyment of this product,

always read the instruction book carefully before using.

Para su seguridad y para disfrutar plenamente de este producto,

siempre lea las instrucciones cuidadosamente antes de usarlo.

An que ce produit vous procure en toute sécurité beaucoup de satisfaction,

lisez toujours soigneusement les directives avant de l’utiliser.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS.

2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

3. Children should be supervised to ensure that they do not play with the appliance.

4. To protect against electrical hazards, do not put the Waring

Drink Mixer in water or other liquids.

5. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.

6. Avoid contact with moving parts.

7. Do not operate the Waring

Drink Mixer or any other electrical equipment with a damaged cord or plug, or after the unit malfunctions or is dropped or damaged in any manner. Return it to the nearest authorized service facility for examination, repair or adjustment.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot surfaces.

10. Put this booklet in a safe place. Do not discard.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

For your protection, the Waring® Drink Mixer is equipped with a 3-conductor cord set.

120-volt units are supplied with a molded 3-prong groundingtype plug, and should be used in combination with a properly connected grounding-type outlet as shown in Figure 1.

If a grounding type outlet is not available, an adapter, shown in Figure 2, may be obtained to enable a 2-slot wall outlet to be used with a 3-prong plug.

Referring to Figure 3, the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate.

CAUTION: Before using an adapter, it must be determined that the outlet cover plate screw is properly grounded. If in doubt, consult a licensed electrician.

Never use an adapter unless you are sure it is properly grounded.

NOTE: Use of an adapter is not permitted in Canada.

HOW TO USE YOUR WARING® DRINK MIXER

Your new Waring® Drink Mixer has an automatic ON/OFF switch (actuator), located behind the front tab of upper cup holder, that starts the motor when the mixing cup is placed in the proper position on the cup support. The cup support has two steps. To activate the automatic ON/OFF switch, the bottom of the mixing cup must be securely resting on the upper step of the cup support and the top rim of the mixing cup must go behind the front tab of upper cup holder.

The motor will continue to operate while the mixing cup remains on the mixer, activating the actuator.

Removal of the container will shut off the motor. The 3-speed switch on top of the Waring

Drink Mixer regulates the operating speed. Choose either LO (I), MED (II), or HI (III) speed. For mixing heavy drinks, use high speed only; for light drinks with more liquid, use low speed.

The drink mixer can be operated without engaging the ON/OFF cup actuator by using the PULSE

toggle switch. The Pulse switch will operate at whatever speed the 3-speed switch is set to. The PULSE

switch will only operate while pressed forward or

backwards. Keep a ﬁrm grip on the cup while using PULSE

Your Waring® Drink Mixer is supplied with 6 agitators, 3 standard and 3 “buttery” (with the movable aps). To switch agitators, simply hold the spindle shaft with one hand and turn the agitator in a clockwise direction. This will loosen the screw, and you can unscrew to remove. Insert replacement agitator and screw bottom screw back in. Tighten by turning the agitator in a counterclockwise direction. Use only standard metal mixing cups with the drink mixer.

CLEANING & SANITIZING INSTRUCTIONS

1. Rinse container thoroughly under running water. Add 8

ounces of clean rinse water to container. Place container in normal operating position on mixer and run on high speed for two (2) minutes. Empty container. Repeat process for all spindles.

2. UNPLUG MIXER POWER CORD FROM ELECTRICAL

OUTLET.

3. To remove bottom cup supports (C), simply push each

support up, then pull out.

4. To remove the upper cup holders (D), hold the notches on

both sides of the holder, then pull directly out from the base.

5. Wash, rinse, and sanitize the container supports, upper

cup holder and container. Sanitize these parts by immersing in sanitizing solution for two (2) minutes. Shake off excess moisture and allow parts to air dry.

6. Working from the top down, wash, rinse, and sanitize the

portion of the mixer housing situated directly over the container and the portion of the spindle above the agitator, using absorbent wiping cloths moistened with cleaning solution, rinse water and sanitizing solution.

7. Reassemble upper cup holder and cup supports to mixer

housing by reversing steps 3 and 4.

8. For each spindle wash, rinse, and sanitize the bottom of the

spindle and the agitator (Illustration A and B) as follows:

Plug the Waring

Drink Mixer cord into electrical outlet.

For each spindle, add 8 ounces of washing solution to

container and place in normal operating position on mixer. Run on high speed for a minimum of two (2) minutes. Empty container and repeat two-minute run with 8 ounces

of water. Empty container and repeat two-minute run with 8 ounces

of sanitizing solution. Empty container. Run motor for a few seconds with empty

container in normal operating position to spin off any excess

moisture. Do not rinse container, spindle or agitator after

sanitizing is completed. Allow all parts to air dry. Wash, rinse, and sanitize as outlined above prior to initial use and

whenever mixer will not be used again within a period of one hour to avoid bacteria build up.

Surfaces of the mixer housing that are outside of the food contact areas may be cleaned as required, using wiping cloths moistened with cleaning solution, rinse water and sanitizing solution.

UNPLUG POWER CORD FROM ELECTRICAL OUTLET BEFORE CLEANING HOUSING. Prevent liquid from running into housing by wringing all excess moisture from wiping cloths before using them.

Washing solutions based on non-sudsing detergents and chlorine-based sanitizing solutions having a minimum chlorine concentration of 100 PPM are recommended.

The following washing, rinsing, and sanitizing solutions, or their equivalents, may be used:

HELPFUL HINTS

1. Always unplug the Waring® Drink Mixer before

disassembling or assembling parts.

2. Be sure to keep all the instructions, parts lists, and service

information in a safe and handy place.

3. If using ice, only use crushed ice or small cubes in the

Waring

Drink Mixer.

4. Clean the Waring

Drink Mixer thoroughly before

initial use.

5. Keep containers clean. Wash, rinse and sanitize thoroughly

after use.

6. Be sure that all detachable parts are fastened tightly before

operating the Waring

Drink Mixer.

7. Operate the Waring

Drink Mixer only when it is fully

assembled.

8. To avoid splashing drinks of thin consistency, operate

on low speed.

LIMITED ONE YEAR WARRANTY

Waring warrants every new Waring® Drink Mixer to be free from defects in material and workmanship for a period of one year from the date of purchase when used with foodstuffs, nonabrasive liquids (other than detergents) and nonabrasive semiliquids, providing it has not been subject to loads in excess of the indicated rating. In addition, the motor in this appliance has a full three year warranty.

Under this warranty, the Waring Commercial Division will repair or replace any part that, upon our examination, is defective in materials or workmanship, provided the product is delivered

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE Washing: Calgon® Calgolac 1 Tablespoon/Gallon Hot (115°F) Rinsing: Plain Water Warm (95°F) Sanitizing: Clorox® Institutional 1 Tablespoon/Gallon Cold (50°F–70°F)

Bleach

+ 14 hidden pages