Walther LG300XT Carbontec Instruction Manual

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

and butt plate through rack mechanism and scale

• XT anti-vibration system

• Carbon as a carrier system ensures an extremely light and highly stable design

• The newly developed core made of special foam reduces vibrations considerably

• Optimized system bedding for tension-free rest in the stock

• Improved adjustment possibilities and reproducibility of these settings for cheek piece

Be sure to read the enclosed standard operating instructions before using the rifle.

By purchasing this sporting weapon you have chosen a product of the highest quality: an en-

hanced member of the time-proven LG 300 air gun series made by WALTHER. The following

features deserve special mention:

• Individually adjustable center of gravity position by means of moveable shaft weights

• Fore-end adjustable in height and inclination

• Improved grip

• Removable on-board computer with easy-to-read LCD display

-8-

at least 300 shots per cylinder (at 200 bar)

weights

approx. 4,360 with steel cylinder, without additional weights

1,053 –1,115 / 260 / 50

System pressure, bar 300 and 200

Working pressure, bar approx. 60

Firing capacity at least 600 shots per cylinder (at 300 bar)

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

Care of the carbon fiber stock:

Carbon is insensitive to all commonly used cleaning agents and weapon oils. It needs no

special care. Occasional wiping of the surface with a soft cloth is sufficient.

Technical data:

Caliber, mm 4.5 single-shot rifle

Weight, g approx. 3,960 with aluminum cylinder, without additional

Dimensions L/H/W,

mm

Sight length, mm 650 – 830

Trigger weight 50 - 120

Raised line of sight

Service booklet, for free annual main-

tenance

Accessories:

Additional weights

High-quality hard protective case

a knurled

screw.

-7-

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

Stock weights:

To insert additional weights into the fore-end, remove the compressed air cylinder. The

weights can be easily adjusted from the outside. Fix them in position using the key supplied or

-2-

LG300XT CARBONTEC

OPERATING INSTRUCTIONS – SUPPLEMENT

Stock adjustment:

The stock can be adjusted in a large number of ways, making it possible to adapt this sport-

ing weapon perfectly to one’s individual needs.

-5-

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

Chest rest:

The rests are variably adjustable to fit against the chest. The contact with the weapon

that one is accustomed to from a wood stock can be perfectly adjusted to one’s individual

needs. Loosen the screw (1) to set the inclination and direction of each eccentric rest

piece. In addition, the height and lateral position of the bar can be varied by loosening

the screw in the bar (2).

To adjust the

inclination of the

butt plate, loosen

the screws (3).

To move the

plate all the way

up, remove the

screws (3) and

move the plate

attachment up.

To move the butt

plate in a lateral

direction, loosen

the screws (4).

(Observe sports

ordinance!) For

additional ad-

justment possi-

bilities please see

the enclosed

MEC operating

instructions.

-4-

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

Stock length adjustment:

To adjust the length of the stock, loosen the screws (1) and turn the knurled screw (2). Then

retighten the clamping screws.

Butt plate adjustment:

(2). Then fix this

setting with the

socket head cap

screw (1). To

adjust the inclina-

tion, loosen the

socket head cap

screw (3) and

tighten it again

after the required

position has been

found. Change the

lateral position of

the cheek piece by

loosening the

screws (4). If a

larger lateral ad-

justment is re-

quired, remove the

screw (3) and

move the entire

cheek piece side-

-3-

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

Cheek piece adjustment

The cheek piece can be easily adjusted without dismantling. To change the height, loosen the

socket head cap screw (1) and set the cheek piece to the desired height using the knurled screw

ways. To change the longitudinal position of the cheek piece, remove the screws (4) all the

way, take off the cheek piece, move the sliding blocks and put the cheek piece back on.

-6-

LG300XT CARBONTEC

OPERATING INSTRUCTIONS - SUPPLEMENT

Fore-end adjustment

Loosen the screw (1) to turn the fore-end on the longitudinal axis. To adjust the height

and inclination of the fore-end, loosen the screws (2). Retighten them afterwards.