Waldorf RN8110GE, RN8110GEC, RNL8110GEC, RNL8110GE Installation And Operation Manual

Installation and Operation Manual

RN8110GE
RN8110GEC

Gas Target Top Range
Electric Ovens

Date Purchased

Serial Number

Dealer

Service Provider

229244-21

For use in GB & IE

RNL8110GE
RNL8110GEC

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previous ly in
writing by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.

© Copyright Moffat Ltd. January 2012.

MANUFACTURED BY

Moffat Limited

Christchurch
New Zealand

INTERNATIONAL CONTACTS

AUSTRALIA

Moffat Pty Limited
E.Mail: [e-mail]
Main Office: (tel): [phone]

(fax): [phone]

Service: (tel): 1800 622 216
Spares: (tel): 1800 337 963
Customer Service: (tel): 1800 335 315
(fax): 1800 350 281

CANADA

Serve Canada
Web: www.servecanada.com
E.Mail: [e-mail]
Sales: (tel): 800 551 8795 (Toll Free)
Service: (tel): 800 263 1455 (Toll Free)

NEW ZEALAND

Moffat Limited
Web: www.moffat.co.nz
E.Mail: [e-mail]
Main Office: (tel): 0800 663328

UNITED KINGDOM

Blue Seal
Web: www.blue-seal.co.uk
E.Mail: [e-mail]
Sales: (tel): [phone]

(fax): [phone]
Spares: (tel): [phone]
(fax): [phone]
Service: (tel): [phone]
(fax): [phone]

UNITED STATES

Moffat
Web: www.moffat.com
Sales: (tel): 800 551 8795 (Toll Free)

(tel): [phone]
(fax): [phone]
Service: (tel): 800 858 4477 (Toll Free)
(tel): [phone]
(fax): [phone]

REST OF WORLD

Moffat Limited
Web: www.moffat.co.nz
E.Mail: [e-mail]

Contents

Waldorf Gas Target Top Range Electric Ovens

RN(L)8110GE Gas Target Top Range Electric Static Oven.
RN(L)8110GEC Gas Target Top Range Electric Convection Oven.

Introduction .............................................................................................. 2

Specification .............................................................................................. 3

Model Numbers Covered in this Specification
General
Gas Supply Requirements
Gas Connection
Electrical Supply Requirements
Electrical Connection

Dimensions ................................................................................................ 5

Installation ................................................................................................ 6

Installation Requirements
Unpacking
Location
Clearances
Assembly
Rear Rollers Fitting
Gas Connection
Electrical Connection
Commissioning

Operation ................................................................................................. 11

Operation Guide
Description of Controls
Lighting Pilot Burner (Target Top)
Lighting Main Burner (Target Top)
Oven

Cleaning and Maintenance ...................................................................... 14

General
After Each Use
Daily Cleaning
Weekly Cleaning
Periodic Maintenance

Fault Finding ............................................................................................ 16

Wiring Schematic .................................................................................... 17

RN8110GE
RN8110GEC

Gas Conversion and Specifications ......................................................... 20

Conversion Procedure
Gas Specifications

Replacement Parts List ........................................................................... 24

Introduction

2

We are confident that you will be delighted with your WALDORF Gas Target Top Range Electric Oven, and
it will become a most valued appliance in your commercial kitchen.
To ensure you receive the utmost benefit from your new Waldorf appliance, there are two important things
you can do.

Firstly:

Please read the instruction book carefully and follow directions given. The time taken will be well spent.

Secondly:

If you are unsure of any aspect of the installation, instructions or performance of your appliance,
contact your WALDORF dealer promptly. In many cases a phone call could answer your question.

CE Only:

These instructions are only valid if the country code appears on the appliance. If the code does not
appear on the appliance, refer to the supplier of this appliance to obtain the technical instructions for
adapting the appliance to the conditions for use in that country.

GREAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK OF

FIRE.

 T

HE APPLIANCE MUST NOT BE LEFT ON UNATTENDED.

 I

T IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICE PERSON TO ENSURE

CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED.

 DO NOT

STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF THIS

OR ANY OTHER APPLIANCE.



DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

Warning



This appliance is for professional use and is only to be used by qualified
persons.



Only authorised service persons are to carry out installation, servicing or gas
conversion operations.



Components having adjustments protected (e.g. paint sealed) by the
manufacturer should not be adjusted by the user / operator.



DO NOT operate the appliance without the legs supplied fitted.

Caution

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY

DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE.

Warning

INSTRUCTIONS

TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS ARE TO BE POSTED IN A PROMINENT

LOCATION. THIS INFORMATION SHALL BE OBTAINED BY CONSULTING THE LOCAL GAS SUPPLIER.

Warning

Specifications

3

Model Numbers Covered in this Specification

RN[1]8110GE Gas Target Top Range Electric Static Oven - 900 mm.
RN[1]8110GEC Gas Target Top Range Electric Convection Oven - 900 mm.

NOTE:

[1]: - Back Options;

- - Standard Models.
L - Low Back Models.

General

A commercial heavy duty, gas fired Target Top Range / Electric Oven, having a high output, two
stage double-ring cast iron burner offering accurate temperature control and infinitely variable heat
with the heat radiating out from the centre of the Target Top. The Main Burner is located
underneath removable cast target top plates.
With heavy duty, high efficiency electric static or convection oven options, fitted with a 900mm,

6.5kW electric static oven and a 6.6kW Convection Oven created for compact modular kitchens.
Both ovens are fitted with 4.5kW bottom element and 2.0kW top element. The Convection oven is
fitted with a 100W oven fan motor.

Gas Supply Requirements

- Non CE Only (Australia / New Zealand):

- CE Only:

Appliance Classification

Category: II

2H3P.

Flue Type: A1.

* Measure burner operating pressure at target top hob manifold test point with target top burner

(Inner and outer ring) operating at full setting. Operating pressure is ex-factory set through
appliance regulator and not to be adjusted, apart from when carrying out gas conversion, if
required. (Refer to ‘Gas Conversion’ section for details).

Natural Gas LP Gas (Propane)

Input Rating 45 MJ/hr 45 MJ/hr
(N.H.G.C.) (42,650 BTU) 42,650 BTU)

Supply Pressure

1.13 - 3.40 kPa 2.75 - 4.50 kPa

(4.5” - 13.5” w.c.) (11” - 18.0” w.c.)

1.0 kPa (*) 2.6 kPa (*)
(4.0” w.c.) (10.0” w.c.)

Gas Connection ¾” BSP Male

Operating Pressure

Natural Gas (G20) Propane (G31)

Heat Input (nett)

Nominal 11.5 kW 11.5 kW
Reduced 4.7 kW 7.9 kW

Gas Rate (nett)

Nominal 1.22 m3/hr 0.89 kg/hr
Reduced 0.50 m3/hr 0.61 m3/hr

Supply Pressure 20 mbar 37 mbar
Burner Operating Pressure 9.9 mbar (*) 26.8 mbar (*)
Gas Connection

3

/4” B.S.P. Male

Specifications

4

Gas Connection

Gas supply connection point is located at rear of the appliance, 130mm from right hand side, 32mm
from rear, 655mm from floor and is reached from beneath appliance. An optional underside
connection is available. (Refer to the ‘Dimensions’ section).

Connection is ¾" BSP male thread.

Electrical Supply Requirements

Electrical Connection

Electrical supply connection point is located at rear of appliance, 80mm from right hand side, 466mm
from rear and 150mm from floor.

When connecting a this electric appliance to mains supply, ensure that the following is carried out:-

 An isolating switch is fitted within 2m of appliance, but not on appliance and in such a position

that user does not have to reach across cooking surface.

 Supply cord shall be oil-resistant, sheathed flexible cable and not lighter than ordinary

polychloroprene or other equivalent synthetic elastomer sheathed cord (as per AS / NZS 3191
part 2.10.11. or IEC 60245-IEC-57) e.g. HO5 RN-F Type.

 Branch supply line shall be individually overload protected to correct current rating and supply

chord shall be protected against any mechanical or thermal damage.

 A grommet is fitted around wiring entry hole into appliance.
 All wiring connections must be tight.

Refer to appropriate wiring standards for size of cable to be supplied to an appliance for current
drawn on that line.

MODEL

1-Phase Connection

1P+N+E

230-240V

3-Phase Connection

3P+N+E

400-415V

RN8110GE

6.5 kW,

26.6 Amps @ 235 V

6.5 kW

L1 - 8.2 Amps
L2 - 9.2 Amps
L3 - 9.2 Amps

RN8110GEC

6.8 kW,

27.9 Amps @ 235 V

6.8 kW

L1 - 9.5 Amps
L2 - 9.2 Amps
L3 - 9.2 Amps

THIS APPLIANCE MUST BE EARTHED. I F SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY A SUITABLY

QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.

Warning

Dimensions

5

RN(L)8110GE / GEC

Installation

6

Installation Requirements

NOTE:

 It is most important that this appliance is installed correctly and that operation is correct

before use. Installation shall comply with local gas, electrical and health and safety
requirements.

 This appliance shall be installed with sufficient ventilation to prevent the occurrence of

unacceptable concentrations of health harmful substances in the room, the appliance is
installed in.

Waldorf Target Top Range Electric Ovens are designed to provide years of satisfactory service, and correct
installation is essential to achieve the best performance, efficiency and trouble-free operation.
This appliance must be installed in accordance with National installation codes and in addition, in
accordance with relevant National / Local codes covering gas, electrical and fire safety.

Australia: - AS5601 - Gas Installations.
New Zealand: - NZS5261 - Gas Installation.
Australia / New Zealand: - AS / NZS3000 - Wiring Rules.
United Kingdom: - Gas Safety (Installation & Use) Regulations 1998.

- BS6173 - Installation of Catering Appliances.

- BS5440 1 & 2 - Installation Flueing & Ventilation.

- BS7671 - Requirements for Electrical Installation.

Ireland: - IS 820 - Non - Domestic Gas Installations.

Installations must be carried out by qualified persons only. Failure to install equipment to
relevant codes and manufacturer’s specifications shown in this section will void the warranty.

Components having adjustments protected (e.g. paint sealed) by manufacturer are only
to be adjusted by an authorised service agent. They are not to be adjusted by the installation
person.

Unpacking

 Remove all packaging and transit protection from appliance including all protective plastic

coating from exterior stainless steel panels.

 Check equipment and parts for damage. Report any damage immediately to carrier and distributor.
 Report any deficiencies to distributor who supplied the appliance.
 Check available gas and electrical supply is correct to as shown on rating plate located on front right

hand corner of bottom sill.

Location

1. Installation must allow for a sufficient flow of fresh air for combustion air supply.

2. Installation must include adequate ventilation means, to prevent dangerous build up of combustion
products.

3. Never directly connect a ventilation system to appliance flue outlet.

4. Any gas burning appliance requires adequate clearance and ventilation for optimum and trouble-free
operation. Minimum installation clearances shown overleaf are to be adhered to.

5. Position appliance in its approximate working position.

6. All air for burner combustion is supplied from beneath appliance. Legs must always be fitted and no
obstructions placed on underside or around base of appliance, as obstructions will cause incorrect
operation and / or failure of appliance.

Combustion Air Requirements:

RN8110GE RN8110GEC

Natural Gas 12m

3

/hr 12m3/hr

LPG 12m

3

/hr 12m3/hr

Installation

7

7. Components having adjustments protected (e.g. paint sealed) by manufacturer are only to be
adjusted by an authorised service agent. They are not to be adjusted by the installation person.

NOTE: Do not obstruct or block appliances flue. Never directly connect a ventilation system to

appliance flue outlet.

Clearances

NOTE: Only non-combustible materials can be used in close proximity to this appliance.

* Side clearances can be 50mm when adjacent surface is at least 100mm below cooking surface.

Assembly

This model is delivered completely assembled. Ensure that legs
are securely attached.

NOTE:

 This appliance is fitted with adjustable feet to

enable it to be positioned securely and level on
uneven floors. This should be carried out on
completion of gas connection. Refer to 'Gas
Connection Section'.

 This appliance can also be fitted with rear rollers to

enable appliance to be easily moved for
positioning and cleaning purposes. If desired,
these rollers are supplied in packaging, with
appliance. See below for fitting instructions.

Optional Accessories (Refer to Replacement Parts
List)

 Plinth Kit. For installation details, refer to instructions

supplied with each kit.

Fitting Rear Rollers.

1. Raise appliance from floor by approx. 75mm
using suitable lifting equipment (i.e. Palletiser /
Forklift) to allow rear adjustable feet to be
removed.

2. Unscrew and remove both rear adjustable feet
from rear leg housings.

3. Fit rear roller to rear leg housing and align
screw hole in side of rear leg housing with
threaded hole in rear roller.

4. Secure rear roller to leg support with bolt
supplied and tighten bolt using a 10mm A/F
spanner.

5. Fit second roller and tighten.

6. Lower appliance back to floor and adjust front
adjustable feet to level appliance.

Combustible Surface Non Combustible Surface

Left / Right hand side 50mm 0mm
Rear 50mm 0mm

Fig 1

Appliance

Base

Adjustable

Foot

Rear Roller

Assy

Rear Leg

Housing

Roller

Locating Bolt