Waldorf RN8100G, RNL8100G, RNB8100G, RNLB8100G Installation And Operation Manual

Installation and Operation Manual

Gas Target Top

Date Purchased

Serial Number

Dealer

Service Provider

228092-20

For use in GB & IE

RN8100G RNB8100G
RNL8100G RNLB8100G

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previous ly in
writing by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.

© Copyright Moffat Ltd. November 2014.

MANUFACTURED BY

Moffat Limited

Rolleston 7675
New Zealand

INTERNATIONAL CONTACTS

AUSTRALIA

Moffat Pty Limited
Web: www.moffat.com.au
E.Mail: [e-mail]
Main Office: (tel) [phone]

(fax) [phone]

Service: (tel): 1800 622 216
Spares: (tel): 1800 337 963
Customer Service: (tel): 1800 335 315
(fax): 1800 350 281

CANADA

Serve Canada
Web: www.servecanada.com
E.Mail: [e-mail]
Sales: (tel): 800 551 8795 (Toll Free)
Service: (tel): 800 263 1455 (Toll Free)

NEW ZEALAND

Moffat Limited
Web: www.moffat.co.nz
E.Mail: [e-mail]
Main Office: (tel): 0800 663328

UNITED KINGDOM

Blue Seal
Web: www.blue-seal.co.uk
E.Mail: [e-mail]
Sales: (tel): [phone]

(fax): [phone]
Spares: (tel): [phone]
(fax): [phone]
Service: (tel): [phone]
(fax): [phone]

UNITED STATES

Moffat
Web: www.moffat.com
Sales: (tel): 800 551 8795 (Toll Free)

(tel): [phone]
(fax): [phone]
Service: (tel): 800 858 4477 (Toll Free)
(tel): [phone]
(fax): [phone]

REST OF WORLD

Moffat Limited
Web: www.moffat.co.nz
E.Mail: [e-mail]

Contents

Waldorf Gas Target Top

RN(L)(B)8100G Target Top - 900mm.

Introduction ............................................................................................. 2

Specifications ........................................................................................... 3

Model Numbers Covered in this Specification
General
Gas Supply Requirements
Gas Connection

Dimensions ................................................................................................ 5

Weight

Installation ................................................................................................ 9

Installation Requirements
Unpacking
Location
Clearances
Assembly
Fitting Adjustable Feet / Rear Rollers to Leg Stand Units
Fitting Adjustable Feet / Rear Rollers to Cabinet and Refrigeration Bases
Gas Connection
Commissioning

Operation ................................................................................................. 15

Operation Guide
Description of Controls
Lighting Pilot Burner
Lighting Main Burner

Cleaning and Maintenance ...................................................................... 17

General
After Each Use
Daily Cleaning
Weekly Cleaning
Periodic Maintenance

Fault Finding ............................................................................................ 19

Gas Conversion and Specifications ......................................................... 20

Conversion Procedure
Gas Specifications

Replacement Parts List ........................................................................... 23

Introduction

2

We are confident that you will be delighted with your WALDORF TARGET TOP, and it will become a most
valued appliance in your commercial kitchen.

To ensure you receive the utmost benefit from your new Waldorf Target Top, there are two important
things you can do.

Firstly:

Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.

Secondly:

If you are unsure of any aspect of the installation, instructions or performance of your appliance,
contact your WALDORF dealer promptly. In many cases a phone call could answer your question.

GREAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK OF

FIRE.

 T

HE APPLIANCE MUST NOT BE LEFT ON UNATTENDED.

 I

T IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICE PERSON TO

ENSURE CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED.

 DO NOT

STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.



DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

Warning



This appliance is for professional use and is only to be used by qualified
persons.



Only authorised service persons are to carry out installation, servicing or gas
conversion operations.



Components having adjustments protected (e.g. paint sealed) by the
manufacturer should not be adjusted by the user / operator.



DO NOT operate the appliance without the legs supplied fitted.

Caution

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CA N CAUSE PROPERTY

DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE.

Warning

INSTRUCTIONS

TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS ARE TO BE POSTED IN A PROMINENT

LOCATION. THIS INFORMATION SHALL BE OBTAINED BY CONSULTING THE LOCAL GAS SUPPLIER.

Warning

Specifications

3

Model Numbers Covered in this Specification
RN[1]8100G - [2] Gas Target Top, 900mm wide.

NOTE:

[1]: - Model Options;

- - Standard.
L - Low Back.
B - Bold Front.
LB - Low Back and Bold Front.

[2] - Base Stand Options;

B - Bench Mount.
CB - Cabinet Base (excluding RN8200G Series).
LS - Leg Stand (excluding RN8200G Series).
RB - Refrigerated Base (RN8600G and RN8800G Series only).

General

A commercial heavy duty, gas fired Target Top having a high output, two stage double-ring cast iron
burner offering accurate temperature control and infinitely variable heat with heat radiating out from
centre of Target Top. Main Burner is located underneath removable cast target top plates.
Target Top is constructed as a hob unit and is available on Leg Stand (-LS), Bench Mount (-B),
Cabinet Base (-CB) or to fit on a Refrigeration Base Unit (-RB).

Gas Supply Requirements

- Australia:

- New Zealand:

- UK Only:

Category: II

2H3P.

Flue Type: A

1.

(*) Measure Burner operating pressure at target top hob manifold test point with target top burner (Inner and Out er rings)

operating at full setting. Operating pressure is ex-factory set, through applian ce regulator and is not to be adjusted,
apart from when carrying out gas conversion, if required. (Refer to details in ’Gas Conversion’ section for
information).

Natural Gas LP Gas (Propane)

Input Rating (N.H.G.C.) 45 MJ/hr 45 MJ/hr
Supply Pressure 1.13 - 3.40 kPa 2.75 - 4.50 kPa
Burner Operating Pressure (*) 1.0 kPa (*) 2.6 kPa (*)
Gas Connection ¾” BSP Male

Natural Gas LP Gas

Input Rating (N.H.G.C.) 45 MJ/hr 45 MJ/hr
Supply Pressure 1.13 - 3.40 kPa 2.75 - 4.50 kPa
Burner Operating Pressure (*) 1.0 kPa (*) 2.6 kPa (*)
Gas Connection ¾” BSP Male

Natural Gas (G20) Propane (G31)

Heat Input (nett)

Nominal 11.5 kW 11.5 kW
Reduced 4.7 kW 7.9 kW

Gas Rate (nett)

Nominal 1.22 m3/hr 0.89 kg/hr
Reduced 0.50 m3/hr 0.61 kg/hr

Supply Pressure 20 mbar 37 mbar
Burner Operating Pressure (*) 9.9 mbar 26.8 mbar
Gas Connection

3

/4” B.S.P. Male

Pilot 200 W 200 W

Pilot 0.02 m3/hr 0.02 kg/hr

Specifications

4

- All Other Markets:



(*) Measure burner operating pressure at target top hob mani fold test point with target top burner (Inner and
outer ring) operating at full setting.

 NAT, LPG & Butane Only - Operating pressure is ex-factor y set and is not to be adjusted, apart from when

converting between gasses, if required.

 (**) TOWN GAS Only - Burner operating pressure is to be adjusted using ad justable gas regulator supplied.

Town Gas Option is only available with specific ex-factory built Town Gas models, which can also be
converted to any other gas. Standard models can only be converted betw een Nat. Gas, LP Gas and Butane,
but not Town Gas.

 Refer to ‘Gas Conversion and Specifications' section of this manual for further details.

Gas Connection

Bench Models Only.

Gas supply connection point is located 130mm from right hand side of appliance, 32mm from rear,
55mm from floor and is entered from beneath appliance. An optional underside connection is
available.

Cabinet and Refrigeration Base Only.

Gas supply connection point is located 130mm from right hand side of appliance, 32mm from rear,
655mm from floor and is entered from beneath appliance. An optional underside connection is
available.

Connection is ¾” BSP male.

For Refrigeration Cabinet Specifications refer to Refrigeration Cabinet Installation and Operation
Manual supplied with appliance.

Natural Gas Town Gas (**)

Input Rating (N.H.G.C.) 45 MJ/hr 45 MJ/hr
Supply Pressure 1.13 - 3.40 kPa 0.75 - 1.50 kPa
Burner Operating Pressure (*) 1.0 kPa 0.63 kPa
Gas Connection ¾” BSP Male

LP Gas (Propane) Butane

Input Rating (N.H.G.C.) 45 MJ/hr 45 MJ/hr
Supply Pressure 2.75 - 4.50 kPa 2.75 - 4.50 kPa
Burner Operating Pressure (*) 2.6 kPa 2.6 kPa

Gas Connection ¾” BSP Male

Dimensions

5

RN

(L)

8100G-B

Weight (Nett)

RN8100G - B 160 kg.

Rating Plate

Location

Dimensions

6

RN

(L)

8100G-LS

Weight (Nett)

RN8100G - LS 180 kg.

Rating Plate

Location

Dimensions

7

RN

(L)

8100G-CB

Weight (Nett)

RN8100G - CB 200 kg.

Rating Plate

Location