V-ZUG CookTopInduction V4000 CTI4T64 Series, CookTopInduction V4000 CTI4T74 Series, CookTopInduction V4000 CTI4T64MMSLD, CookTopInduction V4000 CTI4T64MMSOLD, CookTopInduction V4000 CTI4T64MMSLU Installation Instructions Manual

Installation instructions

1065985-R01

Connection plate

Identification plate

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in
the order specified.

1065985-R01

23/04/2019

Validity

These installation instructions apply to the following models:

Model number With normal mounting frame With DualDesign With oversize mounting frame

31115 CTI4T64MMSLC, CTI4T64MMSOLC CTI4T64MMSLD,

CTI4T64MMSOLD

31116 CTI4T74MMSLC, CTI4T74MMSOLC CTI4T74MMSLD,

CTI4T74MMSOLD

CTI4T64MMSLU, CTI4T64MMSOLU

-

General notes

If installing into a combustible material, the guidelines and standards for low-voltage installations and fire protection
must be strictly observed.

Identification plate

The identification plate is located next to the connection plate.

▸ Affix the second identification plate (supplied) in an accessible position behind the front of the fitted cabinet beneath the appliance.

1

Installation instructions

1065985-R01

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

1065985-R01

23/04/2019

Installation accessories supplied

Oversize mounting frame:

Designation Art. no.

Adjusting brace set H61548

Flush installation:

Designation Art. no.

Cementing-in instructions J004133

Sealing strip set H63283

Spacer set H60330

Accessories

For all installation variants:

Designation Art. no.

Ventilation protective plate set for niche width 550mm H61082

Ventilation protective plate set for niche width 600mm H61083

Ventilation protective plate set for niche width 825mm H61084

Ventilation protective plate set for niche width 900mm H61085

Surface-mounted installation:

Designation Art. no.

Stainless steel intermediate support for the surface-mounted combination of several hobs 1014361

Black intermediate support for the surface-mounted combination of several hobs 1019199

Flush installation:

Designation Art. no.

Steel angle set, installation dimension 60 H63772

Steel angle set, installation dimension 70 H63773

Steel angle set, installation dimension 80 H63774

Instant adhesive for installation of the steel angle (50ml) B11657

Straight mixing nozzle B11656

TREMCLEAN isopropyl alcohol (1000ml) 1056609

Black silicone FA880 (310ml) B11555

Anthracite silicone FA880 (310ml) B11556

White silicone FA880 (310ml) 1031313

Stone grey silicone FA880 (310ml) 1031314

Marble smoothing agent AA320 (1000ml) B11557

Fugenboy (silicone finishing tool) B75158

2

Installation instructions

1065985-R01

Installation pipe Distribution boxClamp

brown + black

blue

yellow/green

black

blue
yellow/green

brown

L2

L1

N

N

L1

PE/

PE/

400 V 2N~

230 V~

≥15

21

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

1065985-R01

23/04/2019

Electrical connection

Electrical connections must be carried out by qualified personnel in accordance with the guidelines and standards
for low-voltage installations and the specifications of the local electricity supply companies.
Refer to the identification plate for information on the required mains voltage, current type and fuse protection.

A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Check old installa­tions.

▸ If the hobs are used at an altitude of over 2,000 meters above sea level, a reduced performance must be expected.

The appliance is equipped with a connection cable which must be connected to an on-site junction box.

Error message U400

Faulty connection:
A pole conductor has been connected to the connection terminal for neutral conductors.

Quickly disconnect the appliance from the mains!

Ventilation

In order to guarantee good ventilation, a space of ≥10mm
height is necessary beneath the appliance.

1. The rear panel of the base unit must be open around the
work surface cut-out to guarantee continuous air circula­tion via the ventilation slits.
The air must be drawn in from outside the cabinet and be
able to circulate freely from inside the cabinet to the hob.

2. Alternatively, a concealed fresh air supply can ensure air
circulation inside the cabinet.
In order that enough cold air can be drawn in, there must
be a continuous circulation of fresh air that extends outside
the cabinet.
The air must be drawn in from outside the cabinet and be
able to circulate freely from inside the cabinet to the hob.

3

Installation instructions

1065985-R01

H

5

8

4

514

Y

Y

490±1

56

0±1

≥

50

≥

5

0

A

550/600

≥57**

Ri

Ra

≥10 *

B

Y – Y

H

Drawer/cabinet

514

H

704

Y

Y

Ri

490±1

≥50

≥50

A

680±1

55

0/

60

0

=

=

=

=

Ra

CTI4T74MMSLC,

CTI4T74MMSOLC

CTI4T64MMSLC,

CTI4T64MMSOLC

Cable length 1.7 mCable length 1.7 m

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

General information about installation

▪ The worktop must be flat so that it is sufficiently sealed against the ingress of liquids.

▪ In order to guarantee good ventilation, a space of at least 10mm in height is necessary beneath the appliance.

Overlying installation with normal mounting frame

The layout of the hob to be fitted may differ from the hob illustrated!

1065985-R01

23/04/2019

* The required clearance must be observed!

** Cut out if niche width 550mm

Type A Depends on producer B H Corner radius Ra/Ri

CTI4T64MMSLC, CTI4T64MMSOLC,
CTI4T74MMSLC, CTI4T74MMSOLC

A Worktop depth (in combination with directly built-under oven; does not apply to small appliances)

B Required clearance for ventilation and service replacement over the entire cut-out area.

H Dimension from the top of the work surface to the underside of the hob (ventilation opening)

Ri Corner radii of appliance Ra Outer corner radii of cut-out

≥20mm ≥60mm 50mm 10/8mm

Installation

1. Create the mounting cut-out accurately.

2. Carefully place the appliance in the mounting cut-out and push against the work surface until flat.

4

Installation instructions

1065985-R01

490±1

≥50

≥50

A

680±1

55

0/

60

0

=

=

=

=

Ra

571

50

1

Y

Y

Ri

H

490±1

56

0±1

≥

50

≥

5

0

A

550/600

Ra

501

Ri

H

691

Y

Y

≥10 *

B

Y – Y

H

Drawer/cabinet

CTI4T74MMSLD,

CTI4T74MMSOLD

CTI4T64MMSLD,

CTI4T64MMSOLD

Cable length 1.7 mCable length 1.7 m

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

Overlying installation

The layout of the hob to be fitted may differ from the hob illustrated!

1065985-R01

23/04/2019

* The required clearance must be observed!

Type A Depends on producer B H Corner radius Ra/Ri

CTI4T64MMSLD, CTI4T64MMSOLD,
CTI4T74MMSLD, CTI4T74MMSOLD

A Worktop depth (in combination with directly built-under oven; does not apply to small appliances)

B Required clearance for ventilation and service replacement over the entire cut-out area.

H Dimension from the top of the work surface to the underside of the hob (ventilation opening)

Ri Corner radii of appliance Ra Outer corner radii of cut-out

≥20mm ≥60mm 50mm 5/1.5mm

Installation

1. Create the mounting cut-out accurately.

2. Carefully place the appliance in the mounting cut-out and push against the work surface until flat.

5

Installation instructions

1065985-R01

507±

1

5

7

7±1

≥41.5

≥41.5

A

550/

600

571

50

1

Y

Y

X

X

Ri

Z

H

501

691

Y

Y

A

5

07±1

≥41.5

≥4

1

.

5

5

5

0

/600

Z

697

±1

X

X

Ri

H

CTI4T64MMSLD,

CTI4T64MMSOLD

CTI4T74MMSLD,

CTI4T74MMSOLD

Cable length 1.7 mCable length 1.7 m

H

≥10 *

Y – Y

B

Drawer/cabinet

Side panel

B

H

≥10 *

X – X

550/600

C

D

Ra

R0–5

8.5

0

-1

8.5

0

-0.5

8.5

8.5

+1

0

+1

0

Detail Z

Steel angle mounted

with adhesive or screws

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

Flush installation

The layout of the hob to be fitted may differ from the hob illustrated!

1065985-R01

23/04/2019

* The required clearance for ventilation must be observed!

Type A Depends on producer B C/D H Corner radius Ra/Ri

CTI4T64MMSLD, CTI4T64MMSOLD ≥20mm ≥75mm 560/490 51.7mm 5/1.5mm

CTI4T74MMSLD, CTI4T74MMSOLD 680/490

A Worktop depth (in combination with directly built-under oven; does not apply to small appliances)

B Required clearance for ventilation and service replacement over the entire cut-out area.

H Dimension from the top of the work surface to the underside of the hob (ventilation opening)

Ri Corner radii of appliance Ra Outer corner radii of cut-out

Installation

1. Create an accurate installation cut-out.

– The mounting surface can be reamed out or created by installing wood/stone supports or using the steel angle set (see Accessor-

ies).

Access to the appliance from below via the entire cut-out area must be guaranteed. For servicing purposes, the induction gen­erator can be removed from below with the mounting plate. It must be possible to unscrew the contact-proof covers from be­low.

2. Prepare the cut-out and appliance in accordance with the specifications in the enclosed cementing-in instructions.

3. Carefully cement the appliance in and leave the silicone sealant to dry for at least 24 hours.

4. Connect to the electrical mains connection before inserting the appliance, if necessary.

6

Installation instructions

1065985-R01

490–530

560–585

550/600

=

=

A

H

600

545

Ri

Ra

Y

Y

≥10 *

B

Y – Y

H

Drawer/cabinet

CTI4T64MMSLU, CTI4T64MMSOLU

Cable length 1.7 m

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

Installation with oversize mounting frame

The layout of the hob to be fitted may differ from the hob illustrated!

1065985-R01

23/04/2019

* The required clearance must be observed!

Type A Depends on producer B H Corner radius Ra/Ri

CTI4T64MMSLU, CTI4T64MMSOLU ≥20mm ≥58.2mm 48.2mm 10/8mm

A Worktop depth (in combination with directly built-under oven; does not apply to small appliances)

B Required clearance for ventilation and service replacement over the entire cut-out area.

H Dimension from the top of the work surface to the underside of the hob (ventilation opening)

Ri Corner radii of appliance Ra Outer corner radii of cut-out

The appliances with oversize frames can also be used as a replacement for solid plate hobs and for installation in complete chrome­nickel steel covers. In the latter case, the solid plate hob part is cut out of the chrome-nickel steel cover and replaced by an appliance
(depth of the work surface ≥30mm). In contrast to normal installation without a fastening system, the appliance is fixed from below us­ing adjusting braces.

7

Installation instructions

1065985-R01

560–585

490–530

=

=

(30)

6 adjusting braces

Aim for
≤R10

≤25

≤32

E D

40

30

(≤ screw length)

(≤ screw length)

Warning, glass breakage:
Do not overtighten screws

Reinforcing slats:

≥25 × 25 mm

Plate for chrome-nickel steel cover

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

Variable areas of the special cut-out dimensions

CTI4T64MMSLU, CTI4T64MMSOLU

1065985-R01

23/04/2019

Reinforcement of the cut-outs with
a complete chrome-nickel steel cover

The installation instructions with regard to electrical and safety-related issues remain fully valid for this installation.

1. Make a precise, right-angled cut-out in the work surface (if not already present). Aim to keep the cut-out dimensions to a minimum.

2. Securely clamp the appliance in the cut-out using the enclosed adjusting braces D and screws E. If necessary, install reinforcing
slats and use these to make the cover flat.

Arrangement of the adjusting braces

8

Installation instructions

1065985-R01

393

(30)

≥67.5

5..10

53.5

56

ø4

≥15

(X)

H

≥3

≤

0.5

2.5

Caution: Mains cable must
not touch protective plate!

Well-fitting seal over
width of cabinet element

Air gap over entire width of
cabinet element

≥17 cm²

According to template

Drawer

Fan

≥5

≥15

(30)

550/600
825/900

H

B

Drawer Centre of fan

≥25 cm²

Air gap over the entire cabinet element width

A

CTI4T64/74
CookTopInduction V4000
Glass ceramic hob

Installation of the ventilation protective plate with 3 mm ventilation gap at the front

A protective plate is necessary for the adequate ventilation of the hob.

The distance between the underside of the appliance and the protective plate must be ≥10mm.

1065985-R01

23/04/2019

Type X Remarks

CTI4T64MMSLC, CTI4T64MMSOLC, CTI4T74MMSLC, CTI4T74MMSOLC 12mm Normal mounting frame

CTI4T64MMSLD, CTI4T64MMSOLD, CTI4T74MMSLD, CTI4T74MMSOLD 12mm Surface-mounted installation

CTI4T64MMSLD, CTI4T64MMSOLD, CTI4T74MMSLD, CTI4T74MMSOLD 10mm Flush installation

CTI4T64MMSLU, CTI4T64MMSOLU 13mm With oversize mounting frame

H Dimension from the top of the work surface to the underside of the hob (ventilation opening).

Cool air supply with regard to drawer or cabinet installed below

In order to guarantee good ventilation, a space of ≥ 10mm height is necessary beneath the appliance.

A Necessary space below the worktop for the appliance.

B Necessary space below the worktop for the ventilation of the appliance.

H Dimension from the top of the work surface to the underside of the hob (ventilation opening)

9