V-Tech VT584 User Manual

VT-584 Outdoor Camera User Manual

Precautions: Do not install camera/bell where there would be a bright light behind the visitor

(or where there would be a bright background), or in a place where the camera lens would be

directly exposed to sunlight or a bright light. If light shines directly into the outdoor camera lens,

the image will be over-exposed; it will look white or silhouetted. Take precautions against this.

Do not install the unit in places where is constant vibration, extreme heat or unusual external

interference.

1. Product Features

● 4-wire Door Entry system, compatible with VT6xx series Monitors

● Camera angle adjustable

● Connects up to 5 Monitors

● Suitable for ush mounting

● Can also be surface mounted by rain cover (not included)

2. Parts List

● VT584 Door/bell camera 1 piece

● 4-Pin wire connector 1 piece (to connect Indoor Monitor)

● 3-Pin wire connector 1 piece (to connect lock)

3. Parts and Functions

2 3

4. Mounting Instruction

1. Cut a hole in 75mm X 75mm X

35mm in the wall. Insert the mounting

bracket and x with screws.

2. Wire up the cables, and test the

system.

3. Hang the door/bell camera body

on top of t he m ou nt in g box, t he n

ti ghte n t he scre ws f irm ly on t he

bottom.

VT-ENG-584-V2 090S817

1. Microphone

35mm

2. Camera

3. Night-View LED

4. Call Button

5. Speaker

6. Angle Adjust

7. Monitor Port

8. Unlock Port LB

145 cm

5. Connect an electron lock(power-ON-to-open)

1R 2W 3Y 4B

Connect to Monitor

Remove the JS/LK jumper on Monitor

Red

Black

Safety Type: Power-on-to-open

The lock consumption must not greater than 12V 500mA.

1R 2W 3Y 4B

3 2 1

The lock consumption must not greater than DC 48V 1.5A.

Safety Type: Power-off-to-open

White

1R 2W 3Y 4B

Connect to Monitor

Keep the JS/LK jumper on Monitor

3 2 1

1R 2W 3Y 4B

Safety Type: Power-on-to-open

Connect to Monitor

Keep the JS/LK jumper on Monitor

3 2 1

The lock consumption must not greater than 48V 1.5A.

1. When connecting an electric lock, an

external power supp ly is needed (not

included).

VT584

2. The rating of the lock must be less than

DC 48V 1.5A.

3. Connect the 2 Black wire to the power

(+), connect 1 Red wire to lock(+), and

connect the power (-) to the lock (-).

Adaptor

+ +

Electronic lock

6. Connect an electro-magnetic lock(power-OFF-to-open)

1. When connecting an electro-magnetic

lock, an external power supply is needed

(not included with this product).

VT584

2. The rating of the lock must be less than

DC 48V 1.5A.

Electron-Magnetic lock

3. Connect the 2 Black wire to the power

(+), connect 3 White wire to lock (+), and

connect the power (-) to the lock (-).

Adaptor

7. Connect a lock using the Monitor power only

1. When using the power solely from the

Monitor, only the Power-on-to-unlock type

electronic lock can be supported. The

rating of the lock must be less than 12V

500mA.

2. Connect the 2 Black wire to the 1 Red

wire from Monitor, connect 1 Red wire to

the lock (+), connect 2 White wire from

Monitor to the lock (-).

8. Specications:

● Power Supply: DC 10~12V (Powered by Monitors)

● Consumption: 150mA in working state (latch not included)

● Video Output: 75Ohm, 1Vp-p, CCIR standard (unless specied)

● Camera: 76 degree, CCD or CMOS camera with IR-LED

● Working temperature: -10 ~ 40 degree

VT584

Electronic lock

VT-ENG-584-V2 090S817