Vtech VM5271-2 User Manual

CAUTION

Go to www.vtechphones.com

CAUTION

to register your product for enhanced warranty support and latest VTech product news.

VM5271-2

Quick start guide

What’s in the box

VM5271-2 baby monitor system

Baby’s room Living room

> 1m (3f t )

• This baby monitoring system includes a special lens which is capable of optical zoom and requires delicate treatment. Please avoid disassembling, dropping, or any other rough handling.

THIS SIDE UP

＞1m (3ft)

> 1m (3f t )

＜1m (3ft)

< 1m (3f t )

Status checkConnect and power on - Baby unit Install the battery Connect and power on - Parent unit

Once you power on your baby monitor, your parent unit displays image from baby unit , and the LINK LED light turns on.

The ON/OFF LED light of baby unit turns on. As baby unit is not being viewed, its ON/OFF LED light ﬂashes.

• The default volume of your parent unit is level 4. If you experience high-pitched screeching noise from your baby monitor while positioning:

- Make sure your baby unit and parent unit are more than 1 meter (3 feet) apart, OR

- Turn down the volume of your parent unit.

Change different views - View

Press VIEW to switch between the image of baby units and .

Press VIEW

Change different views - Patrol

Press PATROL to alternately view the image from baby units and every 10 seconds.

10s

Change different views - Split

Press SPLIT to view the images from all baby units at once.

Dim mode

With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy.

10 min inactivity

Press any buttons

NOTES

TIP

Sound activation

NOTES

Overview - Parent unit

Overview - Baby unit

Automatically turns on the parent unit screen when the baby unit being viewed detects a sound after the screen is turned off. When no sound is detected within 50 seconds, the screen is automatically turned off to save power.

Basic operation - Parent unit

Sound-activated Screen

O

Microphone

Light indicators

TALK VIEW / LCD ON/OFF PATROL SPLIT

POWER Arrow keys

MENU / SELECT

ZOOM IN / ZOOM OUT

Antenna

Stand

Motorized lens with

6x optical zoom

Speaker

Power jack

PLAY/STOP

Basic operation - Baby unit

Light sensor

Microphone

Speaker

SKIP

Antenna

Temperature sensor

ON/OFF light

ON/OFF slide

- VOLUME +

Adjust speaker volume

Press / to adjust your parent unit speaker volume. It determines the volume of sound transmitted from your baby units.

Night vision

Zoom

Press to zoom in or to zoom out.

Talk to your baby unit

Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit.

Long press

Mount the baby monitor (optional)

Turn off the screen

Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the selected baby unit.

Use the menu

Press MENU/SELECT to enter the menu, choose a menu item, or save a setting.

While in the menu:

• Press or to scroll up or down.

• Press to select an item.

• Press to return to the main menu or idle screen.

Turn off the parent unit

Press and hold POWER to power off your parent unit.

Adjust speaker volume

Press - VOLUME + to adjust your baby unit speaker volume. It determines the lullaby volume and talkback volume transmitted from your parent unit.

Lullaby

Press / to play lullaby on the baby units.

• Press to skip to the other lullabies.

• Press / again to stop the lullaby.

Turn off the baby unit

Slide the ON/OFF switch to OFF to power off your baby unit.

The baby unit has infrared LEDs that allow you to see your baby at night or in a dark room. When the baby unit detects low light levels, the infrared LEDs turn on automatically. The images from this baby unit is in black and white, and appears on screen.

• I t is normal if you see a s hort white glar e on your par ent unit screen as the baby unit i s adapting to the dark environment.

• W hen the infrared LEDs are on, the image is in black and white. This is normal du e to external light source s.

• Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit’s angle, or place the baby unit at a higher level to prevent glare and blurry display.

• Check for reception strength and camera angle before drilling the holes.

Place the wall mount bracket on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).

If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are ﬂush with the wall.

Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole ﬁrst, so that the wall mount bracket position is ﬁxed. You can tighten the other screw in the top hole.

Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit.

Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.

Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place.

The default angle of the wall mount bracket is 90 degrees. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.