Vtech SN6167, SN6166 User Manual

CareLine

Models:

™

User’s manual

w w w.v t e c h p h o n e s . c o m

SN6166/SN6167

Congratulations

Compatible with

Hearing Aid T-Coil

TIA-1083

on purchasing your new VTech product. Before using this pendant, please read Important safety instructions on pages 21-22 of

this manual. This manual has all the feature operations necessary to install and

operate your new pendant. Please review this manual thoroughly to ensure proper installation and operation of this innovative and feature rich VTech product. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, visit www.vtechcanada.com.

Telephones identiﬁed with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license.

Registration

Product news

Learn about the latest VTech products.

Parts checklist

Your package contains:

Pendant with lanyard• Pendant belt clip•

Pendant charger with charger adapter• User’s manual•

Pendant charger installation

Install the pendant charger as

1. shown below.

Electrical outlet not controlled by a wall switch

Pendant charger power adapter

Place the pendant in the pendant charger to charge. 3.

Turns red when charging. Turns green when fully charged.

Switch on the pendant.2.

Pendant battery charging

The pendant status light indicates the battery status. If necessary, place the pendant in the pendant charger to charge. For best performance, keep the pendant in the pendant charger when not in use. The battery is fully charged after three hours of continuous charging.

If the pendant status light ﬂashes red and you hear “Low battery,” you need to charge the pendant without interruption to give it enough charge to use for a short time. When the battery is low, the pendant status light ﬂashes red. If you are on a call in low battery mode, the pendant plays short beeps to alert you.

Battery indicators Battery status Action

The pendant status light ﬂashes red. You hear “Low battery” when there is only 30 minutes talk time left. You hear an alert tone every minute.

The pendant status light is solid red.

The battery has very little charge.

The battery has enough charge to be used for a short time.

Charge without interruption.

Pendant attachment

Pendant lanyard:

The pendant lanyard is already attached to the pendant. You can adjust the length of the lanyard for comfortable wearing, or remove the necklace when necessary.

Press down on the push button slider to adjust the length of the lanyard for comfortable wearing.

Necklace

Press down the tabs on both sides of the lanyard clip to remove the necklace of the lanyard.

Pendant belt clip:

Remove the necklace of the pendant lanyard or the whole pendant lanyard before you use the pendant belt clip.

Push the pendant into the belt clip until it clicks in place.

Add and register a pendant

When ﬁrst purchased, charge the pendant in the pendant charger. You hear three beeps every 10 seconds when the pendant is not registered. The new pendant should be charged without interruption for at least 30 minutes before registering it to the telephone base.

Make sure the pendant is out of the pendant charger and turned on.

To register a pendant to your SN1157/SN1197/SN6147/SN6197 telephone base:

Press MENU on the telephone base when idle.

1. Scroll to Settings, then press SELECT.

2. Scroll to Registration, then press SELECT.

3. The telephone base shows Registering... Please wait.

Put the pendant in the pendant charger.

4. The pendant status light ﬂashes red and green to indicate the registration is in progress. Then PENDANT Registered appears on the telephone base, and both devices beep. The pendant is now registered with the telephone base. It takes up to 60 seconds to complete registration.

If you have already set the photo speed dial keys 1 and 2, the

5. telephone base displays Copied Photo Speed Dial 1 to Pendant

Memory 1. Press NEXT, then the telephone base displays Copied Photo Speed Dial 2 to Pendant Memory 2. Then press OK.

-ORIf you have not set the photo speed dial keys 1 and 2, see To

set photo speed dial in the SN1157/SN1197/SN6147/SN6197 Abridged user’s manual to set them.

If registration fails, the telephone base displays Registration failed and you hear an error tone. Start again from Step 1 above.

Add and register a pendant

To register a pendant to your SN6127/SN6187 telephone base:

Press and hold /FIND HANDSET at the side of

1. the telephone base until the IN USE light turns solid red.

Put the pendant in the pendant charger. The

2. pendant status light ﬂashes red and green to indicate the registration is in progress. The pendant beeps. Then it is registered with the telephone base. It takes up to 60 seconds to complete registration.

If registration fails, you hear an error tone. Start again from Step 1 above.

You cannot register a pendant if any other system device is in use.

• If the pendant is not registered and you press or VOICE, you will hear,

•

“Not registered.”

Deregister all devices

If you want to replace a device, or reassign the designated handset number of a registered handset, you must deregister all devices that are registered to the telephone base. Then register each device individually.

To make deregistration easier, read all of the instructions on this and the next page before you begin.

To deregister all devices from your SN1157/SN1197/SN6147/ SN6197 telephone base:

Press and hold FIND HS at the side of the

1. telephone base for about 10 seconds until the telephone base shows Registering... Please wait followed by Deregister all devices?, then release FIND HS.

Deregister all devices

Immediately press YES or FIND HS. Then all devices are

2. deregistered. The deregistration process takes about 10 seconds

to complete.

To conﬁrm deregistration, switch on the pendant and press . When the pendant has been successfully deregistered, you hear “Not registered.”

To deregister all devices from your SN6127/SN6187 telephone base:

Press and hold /FIND HANDSET at the side of the telephone base

1. for about 10 seconds until the telephone base IN USE light turns solid red and then ﬂashes red, then release /FIND HANDSET.

Immediately press /FIND HANDSET. Then all devices are

2. deregistered. The deregistration process takes about 10 seconds to complete.

To conﬁrm deregistration, switch on the pendant and press . When the pendant has been successfully deregistered, you hear “Not registered.”

You cannot deregister all devices if any system device is in use.

Pendant overview

Press to answer or end a call.

•

Pendant status light

Stays solid red when the pendant is charging.

• Flashes red when the pendant is in low

• battery.

Stays solid green when the pendant is fully

• charged.

Flashes red and green when the base is paging

• the pendant.

Flashes quickly in red and green during pendant

• registration.

Flashes orange three times when the pendant is

• not registered.

Pendant light (ring around )

On steady when the pendant is in use.

• Flashes quickly when there is an

• incoming call.

Flashes twice every three seconds when

• another telephone system device is in use.

Pendant overview

Press to call speed dial 1.

•

VOL- and VOL

Press to adjust the listening volume during

• a call or message playback.

Press to adjust the pendant ringer volume

• while in idle mode.

Press to call speed dial 2.

•

ON and OFF switch

Switch to turn the pendant on or off.

•

VOICE

Press to use the voice command feature.

•

Speed dial

To set photo speed dial keys 1 and 2 for the SN1157/SN1197/ SN6147/SN6197 telephone base:

There are four photo speed dial keys on the telephone base. The speed dial keys 1 and 2 on the pendant correspond to the photo speed dial keys 1 and 2 on the telephone base respectively.

We recommend you store two contacts that you may need to call them more often or immediately to photo speed keys 1 and 2.

Telephone base

Pendant

The telephone prompts you to set photo speed dial 1 and photo speed dial 2 when it is initially powered up.

When the telephone base displays Set Photo Speed Dial 1 and

1. Pendant Memory 1, press YES.

When MEMORY 1 NUMBER displays, use the dialing keys to enter

2. a number (up to 30 digits):

Press or to move the cursor to the left or right.

• Press X/DELETE or BACKSPACE to erase a digit.

• Press and hold X/DELETE to erase all digits.

• Press and hold PAUSE to enter a dialing pause (a P appears).

•

Press NEXT.

+ 25 hidden pages