Vtech DS6701 User Manual
User’s manual
DS6701
DECT 6.0 accessory handset
for use with VTech models
DS6751/DS6752
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions on page 4 of this manual.
This manual has instructions on how to set up and register your new handset.
For abridged instructions on using the handset, see the Abridged user’s manual
that came with your telephone base.
You may also view or download the online Complete user’s manual for a full
set of installation and operation instructions at www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced warranty support.
Product news
Learn about the latest VTech products.
BC
1
Parts checklist
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Handset
Handset charger and
charger adapter
Handset battery
compartment cover
User’s manual
User’s manualHandset battery
Battery installation
Install the battery as shown below.
Plug the battery connector securely
1. Place the battery with the label
into the socket.
Slide the battery compartment cover
3.
towards the center of the handset
until it clicks into place.
2.
THIS SIDE UP facing up and the
wires inside the battery compartment.
Place the handset in the telephone
4.
base or charger to charge.
CHARGE light
remains on when
charging.
If the handset will not be used for a long time, disconnect and remove the battery
•
to prevent possible leakage.
To purchase a replacement battery, visit our website at www.vtechphones.com
•
or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
2
Battery charging
Once you have installed the battery, the screen indicates the battery status
(see the table below).
For best performance, keep the handset in the telephone base or
•
charger when not in use.
The battery is fully charged after 11 hours of continuous charging.
•
If you place the handset in the telephone base or charger without
•
plugging in the battery, the screen displays NO BATTERY
Battery indicators Battery status Action
The screen is blank, or
displays Put in charger
and flashes.
The screen displays
Low battery and flashes.
The screen displays
HANDSET X.
The battery has no or very little
charge. The handset cannot
be used.
The battery has enough charge
to be used for a short time.
The battery is charged. To keep the battery
Charge without interruption
(at least 30 minutes).
Charge without interruption
(about 30 minutes).
charged, place it in the
telephone base or charger
when not in use.
It takes up to 11 hours for the battery to be fully charged. When it is fully charged,
you can expect the following performance:
Operation Operating time
While in use (talking*) Up to 7 hours
While in speakerphone mode (talking*) Up to 3.5 hours
While not in use (standby**) Up to 5 days
.
* Operating times vary depending on your actual use and the age of the battery.
** Handset is not charging or in use.
Add and register a handset
This telephone system accommodates up to five handsets. You can add new
handsets (DS6701, purchased separately) to your telephone system. Each handset
must be registered with the telephone base before use. Additional handsets
registered to the telephone base are assigned numbers in the sequential order.
When first purchased and properly charged, each expansion handset shows
To register HS... and ...see manual alternately. Charge the handset before
registering it to the telephone base.
To register a handset:
Place the new/non-registered handset in the telephone base.
1.
Do not place the handset
in the charger.
Both the telephone base and the handset show Registering... Then both
2.
devices show Registered and you hear a beep when the registration process
completes. The registration process takes about 60 seconds to complete.
Deregister handsets
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
Remove any handset put in the telephone base before deregistration.
To deregister all handsets:
Press and hold FIND HANDSET on the telephone base for about 10 seconds
1.
until the telephone base shows Registering... then De-register?
Immediately press and release MENU/SELECT or FIND HANDSET. The
2.
telephone base displays Please wait.
All handsets show To register HS... and ...see manual alternately when the
3.
deregistration process completes. The deregistration process takes about
10 seconds to complete.
3
Loading...