VTech TR02-2013, TR08-2013, TR07-2013, TR05-2013, TR06-2013 User Manual
...
1
TR02-2013/TR05-2013/
TR06-2013/TR07-2013/
TR08-2013
DECT 6.0 accessory handset
for use with VTech models
TR1-2013/TR16-2013/TR17-2013/
TR2-2013/TR26-2013/TR27-2013
User’s manual
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions on page 5 of this manual.
This manual has instructions on how to set up and register your new handset.
For abridged instructions on using the handset, see the Abridged user’s manual
that came with your telephone base.
You may also view or download the online Complete user’s manual for a full
set of installation and operation instructions at www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
BC
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced warranty support.
Product news
Learn about the latest VTech products.
ECO mode
This power conserving technology reduces power
consumption for optimal battery performance.
The ECO mode activates automatically whenever
the handset is synchronized with the telephone base.
The handset shows ECO when the ECO mode activates.
ECO
HANDSET 1
10:15PM
12/18
ECO
2
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
User’s manualHandset battery
Handset battery
compartment cover
Handset charger and
charger adapter
Handset
User’s man ual
Battery installation
Install the battery as shown below.
Plug the battery connector securely
into the socket.
1. Place the battery with the label
THIS SIDE UP facing up and
the wires inside the battery
compartment.
2.
Slide the battery compartment cover
towards the center of the handset
until it clicks into place.
3. Place the handset in the telephone
base or charger to charge.
4.
If the handset will not be used for a long time, disconnect and remove the battery
to prevent possible leakage.
To purchase a replacement battery, visit our website at www.vtechphones.com
or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or
call 1 (80 0) 267-7377.
•
•
CHARGE light
remains on when
charging.
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
3
Battery charging
Once you have installed the battery, the screen indicates the battery status
(see the table below). For best performance, keep the handset in the telephone
base or charger when not in use. The battery is fully charged after 11 hours of
continuous charging.
Battery indicators Battery status Action
The screen is blank, or
displays Put in charger
and ashes.
The battery has no or very little
charge. The handset cannot
be used.
Charge without interruption
(at least 30 minutes).
The screen displays
Low battery and ashes.
The battery has enough charge
to be used for a short time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X.
The battery is charged. To keep the battery
charged, place it in the
telephone base or charger
when not in use.
If you place the handset in the telephone base or charger without plugging in the
battery, the screen displays No Battery.
Add and register a handset
This telephone system accommodates up to ve handsets. Each new handset must
be registered with the telephone base before use. Additional handsets registered to
the telephone base are assigned numbers in the sequential order.
When rst purchased and properly charged, each expansion handset shows
To register HS... and ...see manual alternately. Charge the handset before
registering it to the telephone base.
To register a handset:
Place the new/non-registered handset in the telephone base.
2. After about 10 seconds, the handset displays Registering... When the
registration process completes, the handset displays Registered and you hear
a beep. The registration process takes about 90 seconds to complete.
Deregister handsets
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
If you want to register a handset to another TR1-2013/TR16-2013/TR17-2013/
TR2-2013/TR26-2013/TR27-2013 base, you must deregister all handsets, and then
individually register each handset to the desired base.
To deregister all handsets:
Press and hold /FIND HANDSET on the telephone base for about 10 seconds
until the IN USE light on the telephone base turns on and starts ashing.
Immediately press /FIND HANDSET again. You must press /FIND HANDSET
while the IN USE light is still ashing. The IN USE light ashes for approximately
ve seconds.
All handsets display To register HS... and ...see manual alternately when the
deregistration process completes. The deregistration process takes about
10 seconds to complete.
1.
1.
2.
3.
Do not place the
handset in the charger.
Loading...