VTech DM111-2, DM111 User Manual

User’s manual

baby

’s

sa

fe

ty

wo

rld

Pa

rent Unit

POWER

POWER

POWER

POWER

POWER

baby

’s sa

fe

ty

wo

rl

d

Pa

rent Unit

POWER / LINK

DM111/DM111-2

Safe & SoundTM
audio monitor

Congratulations

on purchasing your new VTech product. Before
using this product, please read Important
safety instructions in this manual.

For support, shopping, and everything new
at VTech, visit our website at
www.vtechphones.com. In Canada, please

visit www.vtechcanada.com.

Register online to get an additional
3-month warranty!

Parts checklist

Baby unit (DM111 BU/DM111-2 BU)

•
Parent unit (DM111 PU/DM111-2 PU)

•

(1 for DM111 and 2 for DM111-2)

Power adapter for baby unit

•
Power adapter for parent unit

•

(1 for DM111 and 2 for DM111-2)

User’s manual

•

Connect

Use only the parent unit power adapter

•
and the baby unit power adapter supplied
with this product.

The parent unit power adapter and baby

•
unit power adapter are intended for a
vertical or floor mount position. The prongs
are not designed to hold the plug in place
if it is plugged into a ceiling,
under-the-table, or cabinet outlet.

Make sure the parent unit, the baby unit

•
and the power adapter cord are out of
reach of children

Both the baby unit and the parent unit are

•
on once connected to the power supply.

Connect the baby unit

Power outlet not
controlled by a
wall switch

Power adapter

Connect the parent unit

Power outlet not
controlled by a
wall switch

Power adapter

Before use

You may test the baby monitor before initial
use, and at regular times thereafter.

To test your baby monitor:

Place the parent unit and the baby unit in the

1.
same room to test the product.

Press and hold on the baby unit until the

2.
POWER light turns off.

Press and hold on the baby unit again

3.
until the POWER light turns on.

Press and hold on the parent unit the

4.
POWER/LINK light turns off.

Press and hold on the parent unit again

5.
until the POWER/LINK light turns on.

If the parent unit is not linked to the baby unit,

•

the POWER/LINK light on the parent unit will
flash. Move the parent unit closer to the baby

unit (but not less than 1 meter / 3 feet).

Positioning the baby monitor

Place the parent unit within the operating range
of the baby unit. We recommend the parent
unit is at least 1 meter (3 feet) away from the
baby unit to avoid audio feedback. If you still
experience audio feedback, move the parent
unit and the baby unit farther apart.

At least 1 meter (3 feet)

Operating range

The operating range of the baby monitor is
up to 300 meters (1000 feet) outdoors or
50 meters (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions, and other
interferences such as walls, doors, and other
obstructions.

Overview

Baby unit overview

1

2

3

Parent unit overview

1

2
3

4
5

6

1 – Visual sound indicator

2 – POWER/LINK light

3 – LOW BATTERY light

4 – (Volume down)
Press to decrease

5 – (On/off)
Press and hold to turn on or off the

parent unit.

6 – Speaker
Listen to sounds transmitted from the

baby unit.

7 – (Volume up)
Press to increase

8 – Belt clip

9 – Battery compartment cover

10 – Power jack

the speaker volume.

the speaker volume.

7
8

9

10

Visit www.vtechphones.com.

Registration

Register your product online for
enhanced warranty support.

Product news

Learn about the latest VTech
products.

Parent unit light

POWER / LINK

LOW BATTERY

POWER/LINK light

Lights off when the parent unit

•
is off.

Lights on in green when the

•
parent unit is on and linked to
the baby unit.

Flashes in green when there is

•
no link between the baby unit
and parent unit, or when the
parent unit is out of range from
the baby unit.

Visual sound indicator

The visual sound indicator shows
the sound level detected from
the baby unit. It also shows the
volume level during speaker
volume setting.

Sound level detected from the
baby unit is indepedent from the
volume level set at the parent unit.

Green lights indicate a

•
moderate sound level detected
from the baby unit; or

Level 1 to Level 3 of the

•

speaker volume setting.
Red lights indicate a higher

•
sound level detected from the
baby unit; or

Level 4 to Level 5 of the

•

speaker volume setting.

LOW BATTERY light

Flashes in red when the

•
battery is low.

Using your baby monitor

Power on or off the baby unit

To turn on the baby unit:

Press and hold until the POWER light

•
turns on.

To turn off the baby unit:

Press and hold until the POWER light

•
turns off.

Power on or off the parent unit

To turn on the parent unit:

Press and hold until the POWER/LINK

•
light turns on.

To turn off the parent unit:

Press and hold unit the POWER/LINK

•
light turns off.

Speaker volume of the parent unit

The speaker volume is preset to Level 3 on the
parent unit. You can adjust to your preferred
sound level.

To adjust the speaker volume:

•

Press to decrease the volume, and to
increase the volume.

If you continue to press or even the

•
volume reaches the minimum or maximum
setting, the parent unit will sound once.

When the parent unit is in mute, the visual

•
sound indicator will still indicate the sound
detected from the baby unit.

Portable use of the
parent unit (optional)

Install the batteries on the parent unit

Use only AAA alkaline batteries (not

•
included).

Do not mix old and new batteries. Do not

•
mix alkaline, standard (carbon-zinc) or
rechargeable (ni-cad, ni-mh, etc) batteries.

When the batteries are installed, the

•
parent unit turns on.

The parent unit does not support

•
recharging.

Slide open the battery compartment cover.1.

2. Flip the ribbon across the battery
compartment.

3. Insert two AAA alkaline batteries into the
battery compartment on top of the ribbon.

4. Slide the battery compartment cover until it

clicks into place.

Standby mode

The parent unit is on standby mode when:

•

it is not connected to the AC power supply; and
there is no sound detected from the baby unit.

•

The standby time varies depending on usage and
the battery life. Full batteries can last up to 8 days.

Replace the batteries when:

LOW BATTERY light flashes on the parent unit.

•

The parent unit beeps twice every 30 seconds.

•

•

The batteries are properly installed into the
parent unit, but the POWER/LINK light on
the parent unit is off.

Storage

When you are not going to use the baby monitor for
some time, remove the batteries from the parent unit.
Store the parent unit, the baby unit and the adapters
in a cool and dry place.

General product care

To clean and maintain this product:

Avoid putting it near heating appliances and devices

•
that generate electrical noise (for example, motors or
fluorescent lamps).

•

DO NOT expose it to direct sunlight or moisture.

•

Avoid dropping the product or treating it roughly.

•

Clean with a soft cloth.

•

DO NOT immerse the parent unit and the baby unit
in water and do not clean them under the tap.

DO NOT use cleaning spray or liquid cleaners.

•

•

Make sure the baby unit and parent unit are dry
before you connect them to the power supply.

Operating range

This product operates with the maximum power
allowed by the Federal Communications Commission
(FCC). Even so, the baby unit and the parent unit can
communicate over only a certain distance - which can
vary with the locations of the baby unit, the parent
unit, the weather, and the layout of your home.

When the parent unit is out of range, it will beep three
times every 10 seconds and enter searching mode.

To improve reception, move closer to the baby unit
(but not less than 1 meter / 3 feet).

1 – POWER light

2 – (On/off)
Press and hold to turn on or off the

baby unit.

3 – Microphone

4 – Power jack

Frequently asked questions

Below are the questions most frequently asked about
Below are the questions most frequently asked about
the baby monitor. If you cannot find the answer to
your question, contact customer service by visiting our
website at www.vtechphones.com or
calling 1 [phone]. In Canada, go to
www.vtechcanada.com or call 1 [phone].

Why does the baby
monitor not respond
normally?

Why doesn’t the
POWER light on the
baby unit turn on
when I switch on the
units?

Why doesn’t the
POWER/LINK
light on the parent
unit turn on when I
switch on the units?

Why does the baby
monitor produce a
high-pitched noise?

Why does the
parent unit react
too quickly to other
sounds?

Try the following (in the order
listed) for common cure:

1. Disconnect the power
from the baby unit and
the parent unit.

2. Remove the batteries
from the parent unit.

3. Connect the baby unit to
the power supply again.
The baby unit turns on.

4. Connect the parent unit
to the power supply
again; or insert two new
AAA alkaline batteries.
The parent unit turns on.

5. Wait for the parent unit
to synchronize with the
baby units. Allow up to
one minute for this to
take place.

Perhaps the baby unit is not
connected to the power
supply.

Connect the baby unit to
power supply. The baby unit
turns on.

Perhaps the battery of the
parent unit is empty and the
parent unit is not connected
to power supply.

Connect the parent unit to
power supply; or insert two
new AAA alkaline batteries
into the parent unit. The
parent unit turns on and
establishes connection with
the baby unit.

The units may be too close
to each other. Make sure
the parent unit and the baby
unit at least 1 meter (3 feet)
away from each other.

The baby unit also picks up
other sounds than those
of your baby. Adjust the
speaker volume on the
parent unit.

4

Baby unit light

POWER

Why don’t I hear a
sound/Why can’t I
hear my baby cry?

Why does the
parent unit beep?

Why does the
parent unit LOW
BATTERY light
flash?

Why can’t I establish
a connection? Why
is the connection
lost every now and
then? Why are there
sound interruptions?

POWER light

•

•

Lights off when the baby unit
is off.

Lights on in green when the
baby unit is on.

You may have muted the
volume or set it to a lower
level. You may need to
adjust the volume to a
higher level.

The baby units may be out
of range. Move the parent
unit closer to the baby units
(but not less than 1 meter /
3 feet).

When the parent unit is
powered by batteries, there
is not sufficient power for
the parent unit to perform
normally. Replace with two
new AAA alkaline batteries.

The baby units may be out
of range. Move the parent
unit closer to the baby units
(but not less than 1 meter /
3 feet).

Other electronic products
may cause interference with
your baby monitor. Try
installing your baby monitor
as far away from these
electronic devices as
possible.

Important safety instructions

When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and injury, including the following:

1. Follow all warnings and instructions marked on
the product.

2. Adult setup is required.

3. This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.

4. This product is not intended for use as a
medical monitor.

5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl, kitchen
sink, laundry tub or swimming pool, or in a wet
basement or shower.

6. CAUTION: Use only alkaline batteries (not
included). There may be a risk of explosion if a
wrong type of battery is used for the parent unit.
Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible
special disposal instructions.

7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Baby unit power adapter: Input 117V AC 60 Hz;
output: 6V DC 300 mA
Parent unit power adapter: Input 100-120V AC 60
Hz; output: 6V DC 400 mA

8. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.

9. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.

10.

Unplug the power cords before replacing the batteres.

11. Do not cut off the adapters to replace them with
other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords.
Do not install this product where the cords may be
walked on or crimped.

13. This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply in your
home, consult your dealer or local power company.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.

16. This product should not be placed in any area
where proper ventilation is not provided. Slots and
openings in the back or bottom of this product
are provided for ventilation. To protect them from
overheating, these openings must not be blocked
by placing the product on a soft surface such as

a bed, sofa or rug. This product should never be
placed near or over a radiator or heat register.

17 Never push objects of any kind into this product

through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.

18. To prevent fire or shock hazard, do not expose
this product to water or any type of moisture.

19. To reduce the risk of electric shock, do not
disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the
product other than specified access doors may
expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock
when the product is subsequently used.

20. You should test the sound reception every time you
turn on the units or move one of the components.

21. Periodically examine all components for damage.

22. Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.

23. Children should be supervised to ensure that they
do not play with the product.

24. The product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

Use and store the product at a temperature

1.

between 32oF and 104oF.
Do not expose the product to extreme cold, heat

2.

or direct sunlight. Do not put the product close to
a heating source.

The batteries should not be exposed to excessive

3.

heat such as bright sunshine or fire.
Make sure the baby unit and the adapter cord are

4.

always out of reach of the baby, at least 1 meter
(3 feet) away from the baby or crib, to avoid a
possible strangulation hazard.

Other electronic products may cause

5.

interference with your audio monitor. Try
installing your audio monitor as far away from
these electronic devices as possible: wireless
routers, radios, cellular telephones, intercoms,
room monitors, televisions, personal
computers, kitchen appliances and cordless
telephones.

Never place the baby unit inside the baby’s crib

6.

or playpen.
Never cover the baby unit or parent unit(s) with

7.

anything such as a towel or a blanket.

Precautions for users of implanted cardiac
pacemakers

Cardiac pacemakers (applies only to digital
cordless devices):

Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless devices and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration,
WTR recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six inches

•
from the pacemaker.

Should NOT place wireless devices directly over

•
the pacemaker, such as in a breast pocket, when it
is turned ON.

WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
user’s manual, the product is safe to be used based
on scientific evidence available today.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to comply
with the requirements for a Class B digital device
under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

•
Increase the separation between the equipment

•
and receiver.

Connect the equipment into an outlet on a circuit

•
different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV

•
technician for help.

Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.

This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with the
FCC criteria. The baby unit shall be installed and used
such that parts of all persons’ body are maintained at
a distance of approximately 20 cm
(8 inches) or more.

This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)

For body worn operation, this parent unit has been
tested and meets the FCC RF exposure guidelines
when used with the accessories supplied or
designated for this product. Use of other accessories
may not ensure compliance with FCC RF
exposure guidelines.

Industry Canada

This device complies with Industry Canada
licence-exempt RSS standard(s).

Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
received, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.

Privacy of communications may not be ensured when
using this product.

The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.

This product meets the applicable Industry Canada
technical specifications.

RF radiation exposure statement

The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The baby unit should be installed and
operated with a minimum distance of 20 cm (8 inches)
between the baby unit and all persons’ body. Use of
other accessories may not ensure compliance with
FCC RF exposure guidelines. This transmitter must
not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment complies
also with Industry Canada RSS-102 with respect to
Canada’s Health Code 6 for Exposure of Humans to
RF Fields.

For cETL compliance only

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez
toujours suivre certaines mesures de précaution
de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont
ceux qui suivent :

Observez toutes les instructions et mises en

1.
garde inscrites sur l’appareil.

L’installation par un adulte est requise.

2.
Ce produit a été conçu pour être un dispositif

3.
d’appoint seulement. Il n’est pas le remplacement
d’une supervision responsable et adéquate par
un adulte et ne devrait pas être utilisé comme
telle.

Ce produit n’est pas conçu pour être utilisé en

4.
tant que moniteur médical.

N’utilisez pas cet appareil près de l’eau ni de toute

5.
autre source d’humidité, par exemple, près d’une
baignoire, cuve à lessive, évier de cuisine, dans
un sous-sol humide ni près d’une piscine, dans un
soussol humide ou une douche.

MISE EN GARDE : Il peut y avoir un risque

6.
d’explosion si vous utilisez le mauvais type de
bloc-piles pour l’unité du parent. N’utilisez que
le piles rechargeable inclus ou le bloc-piles de
rechange. N’incinérez pas les piles. Celles-ci
risqueraient d’exploser.

N’utilisez que les adaptateurs inclus avec ce

7.
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
Adaptateur de l’unité du bébé :
Entrée 117V CA 60 Hz; Sortie : 6 V CC 300 mA
Adaptateur de l’unité du parent :
Entrée 100-120V CA 60 Hz; Sortie : 6 V CC
400 mA

Lorsqu’ils sont branchés dans une prise de

8.
courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la
verticale ou au plancher. Les broches n’ont pas
été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici
est branché dans une prise au plafond, sous une
table ou dans un meuble.

Débranchez ce produit de la prise de courant

9.
avant de procéder au nettoyage. N’utilisez pas de
nettoyants en aérosols. Utilisez un chiffon humide
pour le nettoyer.

Débranchez les cordons d’alimentation avant de

10.
remplacer le bloc-piles.

Ne coupez pas les cordons d’alimentation pour

11.
remplacer les fiches, car ceci peut présenter un
danger potentiel.

Ne laissez aucun objet reposer ni appuyer sur

12.
le cordon d’alimentation. N’installez pas cet
appareil dans un endroit où l’on risque d’écraser

le cordon d’alimentation ou de le piétiner.
Ne faites fonctionner cet appareil qu’avec le

13.
type d’alimentation indiqué sur l’étiquette. Si
vous ne connaissez pas le type d’alimentation
que vous possédez à votre domicile, consultez
votre marchand ou votre compagnie locale
d’électricité.

Ne surchargez pas les prises de courant murales

14.
ni les rallonges électriques.

Ne placez pas cet appareil sur un chariot,

15.
meuble, trépied, support de montage ni table
chancelants.

Les trous et ouvertures du boîtier, situés à

16.
l’arrière de l’appareil ou sous celui-ci, servent à
aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures
et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une
source de chaleur ou d’un calorifère. De plus,
ne placez pas l’appareil dans un endroit avant
de vous assurer qu’il y ait une bonne circulation
d’air.

N’enfoncez jamais d’objets à travers les

17.
ouvertures de cet appareil, car ils pourraient
entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui
peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide
dans ce produit.

Afin de réduire les risques d’électrocution, ne

18.
démontez pas cet appareil, mais apportez-le
dans un centre de service autorisé. L’ouverture
du boîtier ou le retrait de toutes pièces que
contient cet appareil, à l’exception de l’accès
autorisé à certaines portes ou ouvertures,
risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage
incorrect peut par la suite présenter des risques
d’électrocution.

Vous devriez tester la réception chaque fois que

19.
vous mettez l’appareil en fonction.

Examinez les composantes afin de vérifier si

20.
celles-ci ne sont pas endommagées.

Soyez avisé de la perte de la confidentialité

21.
lorsque vous utilisez les ondes publiques. Les
conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones sans
fil, des scanneurs, etc.

Les enfants devraient être supervisés afin de

22.
vous assurer qu’ils ne jouent pas avec l’appareil.

Le produit n’est pas conçu pour être utilisé

23.
par des personnes (incluant des enfants) aux
capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné
suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une
personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

Utilisez et entreposez le produit à une

1.
température entre 0˚ C (32˚F) et 40˚C (104˚ F).
N’exposez pas cet appareil à des froids ou des

2.
chaleurs extrêmes, ainsi qu’à la lumière directe
du soleil. Ne l’installez pas près d’une source de
chauffage.
Le bloc-piles ne doit pas être exposé à la chaleur

3.
excessive telle que la lumière du soleil ou au feu.

Assurez-vous que le moniteur et le cordon

4.

de l’adaptateur sont toujours hors de portée
des enfants, à au moins 1 mètre (3 pieds) de
l’enfant ou du berceau, pour éviter tout risque de
strangulation.
Ne jamais placer le moniteur à l’intérieur du

5.
berceau ou du parc de bébé. Ne jamais couvrir le
moniteur ou l’unité (s) portative avec un article tel
une serviette ou une couverture.
D’autres équipements électroniques peuvent

6.
produire des interférences sur votre moniteur
vidéo et audio. Tentez d’installer votre moniteur
vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil,
radios, téléphones cellulaires, interphones,
moniteurs, téléphones, ordinateurs personnels,
électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans
l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux
dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

Vous devriez maintenir les dispositifs sans fil à au

•

moins six pouces du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil

•

directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.

L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent dispositifs
sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes
se rapportant aux champs électromagnétiques (EMF)
standard. Si vous le manipulez correctement en
suivant les instructions de ce guide, son utilisation
sera sécuritaire pendant de nombreuses années,
selon les meilleures évidences scientifiques dont nous
disposons aujourd’hui.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer”
or “you”) that the Product and all accessories
provided in the sales package (“Product”) are
free from defects in material and workmanship,
pursuant to the following terms and conditions,
when installed and used normally and in accordance
with the Product operating instructions. This limited
warranty extends only to the Consumer for Products
purchased and used in the United States of America
and Canada.

What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?

During the limited warranty period, VTech’s
authorized service representative will repair or
replace at VTech’s option, without charge, a
Materially Defective Product. If we repair the Product,
we may use new or refurbished replacement parts.
If we choose to replace the Product, we may replace
it with a new or refurbished Product of the same
or similar design. We will retain defective parts,
modules, or equipment. Repair or replacement of
the Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or
replacement Products to you in working condition.
You should expect the repair or replacement to take
approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If
VTech repairs or replaces a Materially Defective
Product under the terms of this limited warranty,
this limited warranty also applies to the repaired or
replacement Product for a period of either (a) 90 days
from the date the repaired or replacement Product
is shipped to you or (b) the time remaining on the
original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or

2. Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or

3. Product to the extent that the problem experienced
is caused by signal conditions, network reliability,
or cable or antenna systems; or

4. Product to the extent that the problem is caused by
use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
have been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or

7. Product returned without a valid proof of purchase
(see item 2 on the next page); or

8. Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of
America, visit www.vtechphones.com or
call 1 [phone]. In Canada, go to
www.vtechcanada.com or call 1 [phone].

NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls and
features may save you a service call.

Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery or
handling charges incurred in the transport of the
Product(s) to the service location. VTech will return
repaired or replaced Product under this limited
warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for
damage or loss of the Product in transit. If the
Product failure is not covered by this limited warranty,
or proof of purchase does not meet the terms of
this limited warranty, VTech will notify you and will
request that you authorize the cost of repair prior to
any further repair activity. You must pay for the cost
of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.

What must you return with the Product to get
warranty service?

Return the entire original package and contents

1.
including the Product to the VTech service location along
with a description of the malfunction or difficulty; and

Include a “valid proof of purchase” (sales receipt)

2.
identifying the Product purchased (Product model)
and the date of purchase or receipt; and

Provide your name, complete and correct mailing

3.
address, and telephone number.

Other limitations

This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized
to make modifications to this limited warranty and you
should not rely on any such modification.

State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other
rights, which vary from state to state or province
to province.

Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability
(an unwritten warranty that the Product is fit for
ordinary use) are limited to one year from the date
of purchase. Some states/provinces do not allow
limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue,
inability to use the Product or other associated
equipment, the cost of substitute equipment, and
claims by third parties) resulting from the use of this
Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may
not apply to you.

Please retain your original sales receipt as
proof of purchase.

Technical specifications

Frequency
control

Transmit
frequency

Channels 5

Nominal
effective
range

Power
requirements

VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is the registered trademark of
VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 for VTech Communications, Inc.
All rights reserved. 05/14. DM111-X_CIB_V5.0
Document order number: 91-007297-050-100

Crystal controlled PLL synthesizer

Baby unit: 1921.536-1928.448 MHz
Parent unit: 1921.536-1928.448 MHz

Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.

Baby unit adapter:
Input: 117V AC 60Hz
Output: 6V AC @ 300mA

Parent unit adapter:
Input: 100-120V AC 60Hz
Output: 6V DC @ 400mA

Parent unit battery:
2 X AAA alkaline batteries

Designed to fit your home.
And your life.