Page 1
summit
SS-P TRIPOD KIT
™
Page 2
summit
SS-P TRIPOD KIT
™
The Summit
TM
SS-P is a fi eld-packing tripod with a 3-way pan
head for smooth handing.
3-Way
Pan Head
Split Center Column
(Removable Lower Section)
Foam Leg
Lock
Balance Hook
Quick-Release
Plate
Center Column
Height Adjustment
Knob
Anodized
Aluminum
Legs
Leg Lock on
Rubber Foot
- 2 -
- 3 -
Page 3
summit
SS-P TRIPOD KIT
™
BASIC ADJUSTMENTS
Adjusting the Pan Head
The Summit SS-P features a 3-way pan head that allows you to
quickly follow the action and easily adjust your viewing angle. For
camera use, this head allows you to choose between horizontal and
vertical plate alignments.
Pan and Tilt Action
You can control all of the pan and tilt action with just one hand. To
make any horizontal or vertical adjustments, twist the handle counterclockwise to free the pan
head’s movement. When in
desired position, twist the
handle clockwise to lock.
Plate Angle Lock
Control pan and tilt
action with the handle.
Attaching Optics to the Tripod
1. Flip the plate lever lock
outward and remove the
Tripod Mount
Bolt
quick-release plate.
2. Attach the plate to
your optic or camera. Be
sure to tighten the tripod
mount bolt from the
Quick-Release
Plate
Plate Lever
Lock
bottom side of the plate.
3. Place the quick-release
plate back into the plate
holder. Flip the plate
lever fully back against
the quick-release plate so
your optic rests securely
in the holder.
Flip the plate lever to lock/unlock plate.
Caution
To prevent unnecessary damage to your optics, take a few seconds to
remove your optic from the tripod before you move to a new location.
Spotting scopes and other optics may become damaged if carried
while attached to the tripod. The quick-release plate makes this
easy—and quick!
TIP: Purchase additional quick-release plates for your optics so it is
easy for you to switch equipment.
- 4 -
- 5 -
Page 4
summit
SS-P TRIPOD KIT
™
Adjusting the Tripod Legs
The Summit SS tripod features sturdy anodized legs for reliable
performance.
Center Column
Loosen the center column height
adjustment knob to change the relative
height of the tripod head. Remove the
lower section of the center column for
ultra-low positioning. To help stabilize the
tripod in windy conditions, hang a weight
from the balance hook. (Page 3)
Leg Angle
You can set each leg to one of three
angles. Slide the release tab to the
right and pivot the leg outward to
the desired angle.
Slide release tab to adjust the leg angle.
Leg Length
Each tripod leg extends to a maximum of fi ve
sections. To extend the tripod legs, grab hold
of the rubber foot and twist counter-clockwise
while pulling out on a section. Continue to
twist and pull until you have extended as many
sections as needed. Twist clockwise to lock the
leg sections in place. Note: Twist the foam leg
lock to quickly extend the leg section above
this lock.
- 6 -
Center Column
Height
Adjustment
Knob
Foam Leg Lock
Twist foot to
lock/unlock.
THE VIP WARRANTY
We build products based on our commitment to your absolute
satisfaction. That’s why Vortex tripods are unconditionally guaranteed
and we make this Very Important Promise to you—a Very Important
Person.
Rest assured that in the event your tripod becomes damaged or is
defective, Vortex Optics will repair or replace it at no charge to you.
If we cannot repair your tripod, we will replace it with a product in
perfect working order and equal or better physical condition. Call
Vortex Optics at 800-426-0048 for prompt, professional, and friendly
service.
Vortex Optics
2120 West Greenview Drive
Middleton, WI 53562
service@vortexoptics.com
Visit www.vortexoptics.com for more information. Canadian
customers may visit www.vortexcanada.net for customer service
information.
Note: The VIP Warranty does not cover loss, theft, deliberate
damage, or cosmetic damage that does not hinder the
performance of the product.
- 7 -
Unlimited
Unconditional
Lifetime Warrant y
Page 5
THE FORCE OF OPTICS
®
#ST-5-14A
Loading...