Vortex Optics PRO GT TRIPOD KIT User Manual

VORTEX PRO GT TRIPOD

Using the panhead

The all-metal Pro GT tripod features a panhead with a quick release plate (QR). To pan from left to right, loosen the pan lock thumbscrew (J) and move the control handle (A) in the desired direction. Turn the control handle counter-clockwise to adjust the tilt; turn clockwise to tighten in place.

The Pro GT tripod head comes attached to the tripod legs, but needs

one final assembly step before use. Locate the three set screws on the underside of the tripod connector platform and tighten the screws down with a flathead screwdriver.

Panhead with Quick Release Plate

EDF

How to properly use the Pro GT quick release plate with your spotting scope, binocular, or camera:

1. Press the lever (G) to remove the quick release plate (D) from the panhead.

2. Thread the quick release plate onto the body of the spotting scope, binocular, or

camera and tighten the screw so the connection is secure—be sure the peg on the

tripod platform lines up with the molded area on the plate (see below).

3. Slide the quick release plate back into the groove on the plate platform (I). The

anti-twist pin (F) will retract if not needed.

4. Engage the quick release safety lock by pushing the small brass pin (H) to the right.

This pin prevents the accidental release of the lever.

1. 2. 3. 4.

©Vortex Optics USA 2009

A. Pan and Tilt Control Handle B. Platform Adjustment Thumbscrew C. Panhead Bubble Level D. QR Mounting Plate E. QR Plate Mounting Screw F. Ant i-Twist Pin G. QR L ever H. QR Safety Lock Pin I. QR Plate Platform J. Pan Lock Thumbscrew K. Variable-Angle Leg Release L. Center Column Release Thumbscrew M. Padded Upper Leg Section N. Center Column O. Flip-Lever Leg Lock

Extending the leg length

Each tripod leg has three sections with padding on two of the upper section leg sections (M). To extend the legs, release a flip-lever lock (O) and slide the leg section out to the desired length. Press the flip-lever back down to lock a section in place.

Note: To adjust tension on the leg lock,

release the flip-lever lock and tighten the lever screw with an Allen wrench.

Adjusting the variable leg angle spread

Wrench set included.

Adjust the tripod leg angles for ease of use in various scenarios. Push

in on the leg release button (K)

and lift the leg upward, setting it at one of the three available angles. Repeat with other legs as needed.

The legs on the STX tripod can be independently adjusted to one of three viewing positions.

Warranty and Service

This product is warranted to be free of defects in materials and workmanship for three years after purchase. Vortex Optics will repair or replace such product or part thereof that, upon our inspection, is found to be defective in materials or workmanship.

If you need assistance using your tripod, please contact:

Vortex Optics

2120 West Greenview Drive

Adjusting the center column

Change the position of the center column (N) to gain additional height. Unlock the center column by turning the thumbscrew (L) in a counter-clockwise direction. Maneuver the

Middleton, WI 53562

800-426-0048

service@vortexoptics.com

center column to the desired height and lock in place by turning the thumbscrew in a clockwise direction.

Using the level

Use the leveling bubble on the panhead (C) to gauge your alignment and allow for optimum viewing and photography. The tripod will be level when the bubble is within the black circle.

Adjusting the Camera Angle

The Pro GT tripod allows you to move the plate platform (I) for more convenient photography. Change your camera position from a landscape to portrait format by turning the platform adjustment thumbscrew (B) counter-clockwise, then flip the platform upright and turn the thumbscrew clockwise to lock the angle.