Vizio VX32L Service Manual

Service Manual

Model #: VIZIO VX32L/VW32L

HDTV20A

(AUO/LPL/Samsung Panel)

V, Inc

320A Kalmus Drive Costa Mesa, CA 92626

TEL : [phone] FAX :[phone]

Top Confidential

Table of Contents

CONTENTS PAGE

Sections

1. Features 1-1

2. Specifications 2-1

3. On Screen Display 3-1

4. Factory Preset Timings

5. Pin Assignment

4-1

5-1

6. Main Board I/O Connections 6-1

7. Theory of Circuit Operation 7-1

8. Waveforms 8-1

9. Trouble Shooting 9-1

10. Block Diagram 10-1

11. Spare parts list 11-1

12. Complete Parts List 12-1

Appendix

1. Main Board Circuit Diagram

2. Main Board PCB Layout

3. Assembly Explosion Drawing

Block Diagram

VIZIO VX32L/VW32L HDTV10A Service Manual

VINC Service Manual

VIZIO VX32L/VW32L HDTV20A

COPYRIGHT © 2000 V, INC. ALL RIGHTS RESERVED.

IBM and IBM products are registered trademarks of International Business Machines
Corporation.

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

VINC and VINC products are registered trademarks of V, Inc.

VESA, EDID, DPMS and DDC are registered trademarks of Video Electronics Standards
Association (VESA).

Energy Star is a registered trademark of the US Environmental Protection Agency (EPA).

No part of this document may be copied, reproduced or transmitted by any means for any
purpose without prior written permission from VINC.

FCC INFORMATION
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that the interference will not occur in a particular installation. If this equipment
does cause unacceptable interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures -- reorient or relocate the receiving
antenna; increase the separation between equipment and receiver; or connect the into an
outlet on a circuit different from that to which the receiver is connected.

FCC WARNING
To assure continued FCC compliance, the user must use a grounded power supply cord and
the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized
changes or modifications to Amtrak products will void the user’s authority to operate this
device. Thus VINC Will not be held responsible for the product and its safety.

CE CERTIFICATION
This device complies with the requirements of the EEC directive 89/336/EEC with regard to
“Electromagnetic compatibility.”

SAFETY CAUTION
Use a power cable that is properly grounded. Always use the AC cords as follows – USA (UL);
Canada (CSA); Germany (VDE); Switzerland (SEV); Britain (BASEC/BS); Japan (Electric
Appliance Control Act); or an AC cord that meets the local safety standards.

VIZIO VX32L/VW32L HDTV10A Service Manual

Chapter 1 Features

1. Built in TV channel selector for TV viewing.

2. Simulatnueous display of PC and TV images.

3. Connectable to PC’s analog RGB port.

4. Built in S-video, HDTV, composite video, HDMI and TV out.

5. Built in auto adjust function for automatic adjument of screen display.

6. Smoothing function enables display of smooth texts and graphics even if image

withresolution lower than 1366x768 is magnified.

7. Advanced video functions for personal favor.

8. Power saving to reduce consumption power too less than 3W.

9. On Screen Display: user can define display mode (i.e. color, brightness, contrast,

sharpness, backlight), sound setting, TV channel program, aspect and gamma or

reset all setting.

CONFIDENTIAL – DO NOT COPY Page 1-1

File No. SG-0241

Chapter 2 Specification

1. TFT-LCD CHARACTERISTICS

LPL LC320WX3-SLC1

Item Specification

Display Pixels 1,366 (H) x 768 (V) pixels

Pixel Pitch 170.25 um(H) x 510.75 um(V) x RGB

Color Depth 8 bits 16.7 million colors

Active Display Area 697.685 mm(H)X392.256 mm(V)

Brightness (panel spec) 400cd/m2 (typ)

Contrast ratio (panel spec) 900:1

Color coordinates (typical)

White x=0.279±0.03, y=0.292±0.03

Red x=0.628±0.03, y=0.343±0.03

Green x=0.290±0.03, y=0.612±0.03

Blue x=0.146±0.03, y=0.062±0.03

AUO T315XW02 VC

Item Specification

Display Pixels 1,366 (H) x 768 (V) pixels

Pixel Pitch 0.51075 mm

Color Depth 8 bits 16.7 million colors

Active Display Area 697.685 (H) x 392.256(V)

Brightness (panel spec) 500 cd/m2 (typ)

Contrast ratio (panel spec)

1500:1

Color coordinates (typical)

CONFIDENTIAL – DO NOT COPY Page 2-1

File No. SG-0241

White x=0.28±0.03, y=0.29±0.03

Red x=0.64±0.03, y=0.33±0.03

Green x=0.29±0.03, y=0.60±0.03

Blue x=0.15±0.03, y=0.06±0.03

Samsung LTA320WT-L05

Display Pixels 1,366 (H) x 768 (V) pixels

Pixel Pitch 0.51075(H)X0.17025(W)*3

Color Depth 8 bits 16.7 million colors

Active Display Area 697.6845(H)X392.256(V)

Brightness (panel spec) 450cd/m2 (typ)

Contrast ratio (panel spec)

Color coordinates (typical)

Item Specification

1500:1

White x=0.28±0.03, y=0.29±0.03

Red x=0.642±0.03, y=0.33±0.03

Green x=0.283±0.03, y=0.602±0.03

Blue x=0.145±0.03, y=0.062±0.03

2. TFT-LCD OPTICAL CHARACTERISTICS

Contrast ratio: 1.CR : 900(Typ) 2. CR WITH AI : 2000(Typ)

Surface Luminance, White: 400 cd/m

2 (Typ)

Luminance Variation, δ=1.3 (Max)

Response Time = 8 ms (Max=12mx)

Viewing Angle (CR>10)

Left: 89°typ.

Right: 89°typ.

Top: 89°typ.

Bottom: 89°typ.

CONFIDENTIAL – DO NOT COPY Page 2-1

File No. SG-0241

3. Input Connectors

1 x RF Connector for internal ATSC/QAM/NTSC Hybrid Tune

2x HDMI with HDCP plus Stereo Audio (RCA)

2x Component YPbPr plus Stereo Audio

1x RGB PC(WXGA) plus Stereo Audio

1x Composite Video plus stereo Audio

1x S-VIDEO Connect

4. POWER SUPPLY

Input Voltage Level: 100~240 Vac, 50/ 60 Hz

Power Consumption: 180W MAXPower OFF: to less than 3W MAX

5. Speaker

Output 10W (max) X2

6. ENVIRONMENT

Operating Temperature: 5c~35c (Ambient)

Operating Humidity: Ta= 35 °C, 90%RH (Non-condensing)

Operating Altitude: 0 - 14,000 feet (4267.2m)(Non-Operating)

7. DIMENSIONS (Physical dimension)

Width: 760.0mm. +/- 20 mm

Depth: 51.6 mm +/- 20 mm

Height: 450.0 mm +/- 20 mm

8. WEIGHT (Physical weight)

a. Net: 19.12

b. Gross: 23.81

CONFIDENTIAL – DO NOT COPY Page 2-1

File No. SG-0241

Precaution

Please pay attention to the followings when you use this TFT LCD module.

1. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower

than following voltage :

V=±200mV(Over and under shoot voltage)

(2) Response time depends on the temperature. (In lower temperature, it

becomes longer.)

(3) Brightness depends on the temperature. (In lower temperature, it becomes

lower.)And in lower temperature, response time (required time that

brightness is stable after turned on) becomes longer.

(4) Be careful for condensation at sudden temperature change. Condensation

makes damage to polarizer or electrical contacted parts. And after fading

condensation, smear or spot will occur.

(5) When fixed patterns are displayed for a long time, remnant image is likely

to occur.

(6) Module has high frequency circuits. System manufacturers shall do

sufficient suppression to the electromagnetic interference. Grounding and

shielding methods may be important to minimize the interference.

2. HANDLING PRECAUTIONS FOR PROTECTION

(1) The protection film is attached to the bezel with a small masking tape.

When the protection film is peeled off, static electricity is generated

between the film and polarizer. This should be peeled off slowly and

carefully by people who are electrically grounded and with well ion-blown

equipment or in such a condition, etc.

(2) When the module with protection film attached is stored for a long time,

sometimes there remains a very small amount of glue still on the bezel after

the protection film is peeled off.

(3) You can remove the glue easily. When the glue remains on the bezel

surface or its vestige is recognized, please wipe them off with absorbent

cotton waste or other soft material like chamois soaked with

normal-hexane.

CONFIDENTIAL – DO NOT COPY Page 2-1

File No. SG-0241

Chapter 3 On Screen Display

On Screen Display (OSD) is a friendly interface providing the function adjusting in our system.

Customers could operate it only by few buttons. There is the introduction of the OSD.

Main unit button

MENU OK

CH ▲ ↑

CH ▼ ↓

VOL + ←

VOL - →

Input

[MENU]

“MENU” button could star the OSD which could adjust the performance and set up the setting

between the different input sources. There are the structures.

TV Source

A. Picture：(Bold: Default)

a. Picture Mode (Standard / Movie / Game / Custom)

b. Backlight (0~100, 90)

c. Brightness (0~100, 50)

d. Contrast (0~100, 50)

e. Color (saturation)(0~100, 50)

f. Tint (hue) (-32~32, 0)

g. Sharpness (0~7, 4)

h. Color Temperature (Cool/Normal/Warm/Custom)

i. Advanced Video

1. DNR (Low/Medium/Strong/Off)

2. Black level extender (Off/On)

3. White Peak Limiter (On/Off)

4. CTI (Low/Medium/Strong/Off)

5. Flesh Tone (Off/On)

6. Adaptive Luma (Off/On)

CONFIDENTIAL – DO NOT COPY Page 3-1

File No. SG-0241

CONFIDENTIAL – DO NOT COPY Page 3-2

File No. SG-0241

B. Audio：(Bold: Default)

a. Volume (0~100, 25)

b. Bass (0~100, 50)

c. Treble (0~100, 50)

d. Balance (-50~50, 0)

e. Surround (ON/OFF)

f. Digital Audio Out (PCM/OFF/Dolby Digital)

g. Speaker (ON/OFF)

h. Lip Sync (0~5 , 0)

CONFIDENTIAL – DO NOT COPY Page 3-3

File No. SG-0241

C. TV：(Bold: Default)

a. Tuner Mode (Cable/Antenna)

b. Auto Search

c. Skip Channel

d. MTS (Stereo/SAP/Mono)

e. Time Zone (Eastern/Indiana/Central/Mountain/Arizona/Pacific/Alaska/Hawaii)

f. Daylight Saving (ON/OFF)

CONFIDENTIAL – DO NOT COPY Page 3-4

File No. SG-0241

D. Setup：(Bold: Default)

a. Language (English/ Français / Espaňol)

b. Minuterie de veille (OFF/30Min/60Min/90Min/120Min)

c. Wide (Wide/Panoramic/Normal)

d. Input Naming (AV1/AV2/COMP1/COMP2/RGB/HDMI1/HDMI2)

e. CC (OFF/CC1~4)

f. CC On Mute (OFF/ON)

g. Style de Sous-titre

h. H/V Position

i. Valeurs par defaut

CONFIDENTIAL – DO NOT COPY Page 3-5

File No. SG-0241

E. Parental：(Bold: Default)

Password (Default => 0000)

a. Cannel Block

b. TV Rating

c. Move Rating

d. Check for New DTV Rating

d. Block TV Unrated TV (NO/Yes)

e. Access Code Edit

CONFIDENTIAL – DO NOT COPY Page 3-6

File No. SG-0241

RGB Mode

A. Picture Adjust：(Bold: Default)

a. Auto Adjust

b. Backlight (0~100, 90)

c. Brightness (0~100, 50)

d. Contrast (0~100, 50)

e. Color Temperature (9300/Custom/6500)

f. H-Size (0~255, 127)

g. H-Position (0~100, 48)

h. V-Position (0~100, 47)

i. Fine Tune (0~31, 29)

CONFIDENTIAL – DO NOT COPY Page 3-7

File No. SG-0241

B. Audio：(Bold: Default)

a. Volume (0~100, 25)

b. Bass (0~100, 50)

c. Treble (0~100, 50)

d. Balance (-50~50, 0)

e. Surround (ON/OFF)

f. Digital Audio Out(PCM/OFF/Dolby Digital)

g. Speakers (ON/OFF)

h. Lip Sync (0~5 , 0)

CONFIDENTIAL – DO NOT COPY Page 3-8

File No. SG-0241

C. Setup：(Bold: Default)

a. Language (English/ Français / Espaňol)

b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)

c. Wide (Wide/Normal)

d. Input naming (AV1/AV2/COMP1/COMP2/HDMI1/HDMI2)

e. Rest All Setting (OK/Cancel)

CONFIDENTIAL – DO NOT COPY Page 3-9

File No. SG-0241

AV / COMPONENT MODE

A. Picture：(Bold: Default)

a. Picture Mode (Custom/Standard/Movie /Game / Custom)

b. Backlight (0~100, 90)

c. Brightness (0~100, 50)

d. Contrast (0~100, 50)

e. Color (saturation)(0~100, 50)

f. Tint (hue) (-32~32, 0)

g. Sharpness (0~7, 4)

h. Color Temperature (Cool/Normal/Warm/Custom)

i. Advanced Video

1. DNC (Low/Medium/Strong/Off)

2. Black level extender (Off/On)

3. White Peak Limiter (On/Off)

4. CTI (Low/Medium/Strong/Off)

5. Flesh Tone (Off/On)

6. Adaptive Luma (Off/On)

CONFIDENTIAL – DO NOT COPY Page 3-10

File No. SG-0241

B. Audio：(Bold: Default)

a. Volume (0~100, 25)

b. Bass (0~100, 50)

c. Treble (0~100, 50)

d. Balance (-50~50, 0)

e. Surround (ON/OFF)

f. Digital Audio Out (PCM/OFF/Dolby Digital)

g. Speakers (ON/OFF)

h. Lip Sync (0~5)

CONFIDENTIAL – DO NOT COPY Page 3-11

File No. SG-0241

C. Setup：(Bold: Default)

a. Language (English/ Français / Espaňol)

b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)

c. Wide (Wide/Normal)

d. Input Naming (AV1/AV2/COMP1/COMP2/HDMI1/HDMI2)

e. CC(OFF/CC1-4)

f. CC On Mute (OFF/ON)

g. H/V Position

h. Reset All Setting (OK/Cancel)

CONFIDENTIAL – DO NOT COPY Page 3-12

File No. SG-0241

D. Parental：(Bold: Default)

Password (Default => 0000)

a. Cannel Block

b. TV Rating

c. Move Rating

d. Block Unrated TV (NO/Yes)

e. Access Code Edit

CONFIDENTIAL – DO NOT COPY Page 3-13

File No. SG-0241

HDMI MODE

A. Picture：(Bold: Default)

a. Picture Mode (Custom/Movie/Game/Standard Custom)

b. Backlight (0~100, 90)

c. Brightness (0~100, 50)

d. Contrast (0~100, 50)

e. Color (saturation)(0~100, 50)

f. Tint (hue) (-32~32, 0)

g. Sharpness (0~7, 4)

h. Color Temperature (Cool/Normal/Warm/Custom)

i. Advanced Video

1. DNC (Low/Medium/Strong/Off)

2. Black level extender (Off/On)

3. White Peak Limiter (On/Off)

4. CTI (Low/Medium/Strong/Off)

5. Flesh Tone (Off/On)

6. Adaptive Luma (Off/On)

CONFIDENTIAL – DO NOT COPY Page 3-14

File No. SG-0241

B. Audio：(Bold: Default)

a. Volume (0~100, 25)

b. Bass (0~100, 50)

c. Treble (0~100, 50)

d. Balance (-50~50, 0)

e. Surround (ON/OFF)

f. Digital Audio Out

g. Speakers (ON/OFF)

h. Lin Sync (0~5 , 0)

CONFIDENTIAL – DO NOT COPY Page 3-15

File No. SG-0241

C. Setup：(Bold: Default)

a. Language (English/ Français / Espaňol)

b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)

g. Rest All Setting (OK/Cancel)

CONFIDENTIAL – DO NOT COPY Page 3-16

File No. SG-0241

[INPUT]

“INPUT” could supply an interface providing a list. The list shows input sources and

provides the choices of different sources. The list includes items as below:

A. TV: Analog TV or digital TV

B. AV1, AV2: Composite (AV) signal

C. Component1, Component2: Color difference (YPbPr) video signals.

D. RGB: Video Graphics Array (VGA) or D-sub video signals.

E. HDMI1, HDMI2: High Definition Multimedia Interface (HDMI) multimedia signals.

[INFO]

“INFO” button could show an information bar which displays the information about the

input signal on our LCD TV.

CONFIDENTIAL – DO NOT COPY Page 3-17

File No. SG-0241

Chapter 9 Trouble shooting

(

)

MONITOR DISPLAY NOTHING (PC MODE)

Start

LED is lighted

OrangeÎgreen

N0

1. Is Power board output +5VSB (F1)?

2. Is J1 connector of MB good?

3. Is DC-DC OK?

4. Is U22 pin2 (+3V3SB) working ok?

I

LED is lighting?

Yes

N0

It is in power saving

1. Check video cable

2. Is the timing supported?

3. Check sync input

4. Check VGASOG rout if analog (SOG) (C132)

Yes

N0

Panel has no data

out?

It means data to LVDS

1. Is J8 connecting OK?

2. Check J1 +5VSB (F1)&+12V (F2)

3. Is panel ok?

4. Check P5 D-sub Input correct

5. Check analog input route

Yes

END

CONFIDENTIAL – DO NOT COPY

Page 9-

File No. SG-0241

1

(TV, COMPOSITE VIDEO1, 2, S-VIDEO) IS NOT DISPLAY CORRECTLY

Start

N0

Input signal good?

Yes

1. Check video

2. Check DVD player

N0

U13 input correct?

Yes

N0

LVDS output

Yes

1. Check J8 Connect is good?

2. Is panel working ok?

END

1. Check P2 & J4 signal

2. Check signal between P2 and U13 (IF AV1/AV2 mode)

3. Check Tuner & U13 (IF TV mode)

4. Check J4 (IF S-Video)

5. Check U13 POWER 3.3V

1. Check LVDS LINE

2. Check U13 clock (60MHz)(X1)

3. Check U13 Power

CONFIDENTIAL – DO NOT COPY

Page 9-

File No. SG-0241

2

(COMPONENT1,

2) IS NOT DISPLAY CORRECTLY

Start

N0

Input signal good?

Yes

N0

P3 input correct?

Yes

N0

U13 input correct?

1. Check video

2. Check host’s setting

1. Check signal from P3 & P4

2. Check system power 12V& 5V(5VSB)

1. Check signal between U13 & P3

2. Check Y1 Clock (60MHZ)

Yes

Is LVDS output

Yes

1 .Is J8 connected good?

2. Is panel working ok?

END

N0

1. Check U13

2. Check U13 power 3.3V&2.5v&1.8v&1.25v

CONFIDENTIAL – DO NOT COPY

Page 9-

File No. SG-0241

3

(HDMI) IS NOT DISPLAY CORRECTLY

Start

N0

Input signal

1. Check video

2. Check host’s setting

U13 no data out ?

1.Is J9 connected good?

2.Is panel working ok?

Yes

N0

1. Check P7 & P9 connect

2. Check the pin18 & 19 of P7 & P9

3. Check the pin 6 of U32 & U34

Yes

END

CONFIDENTIAL – DO NOT COPY

Page 9-

File No. SG-0241

4

TROUBLE

OF DC-DC CONVERTER

Start

J1 PIN9,PIN10,PIN11

J1 PIN 2,3,4

U14 pin 5 6 7 8

The voltage is about + 5V(+5VSB)

1. Check power board

2. Check power cable, F1 & connection J1

3. Check U22 pin1 (+5VSB) & pin2 (+3V3SB)

The voltage is about + 12V while power switch on

1. Is J1 connection good

2. Check J1 Pin1 is up to about 3.3V (+3V3SB)?

3. Check power board

4. Check F2.

The voltage is about +5V while power switch on

1. Check F1 & U14

2. Check OPWRSB (R19)

3. Check U14 pin1&2 or pin 3&4, should have -1V
more.

The voltage is about +3.3V

U15, U17,U22

U21 pin2

U19 pin2

1. Check F1 & U14

2. Check U15, U17,U22

The voltage is about +1.2V while power switch on

1. Check F1 & U14

2. Check U21 pin2

The voltage is about +2.5V while power switch on

1.Check J1 Connect

2.Check U19 pin2

The voltage is about +12V to +5V (for Tuner) while power

U16 pin1 & pin2

switch on

1. Check F2

2. Check U16 pin1 (+12V_AP) & U16 pin2 (+5V_TUNER)

END

CONFIDENTIAL – DO NOT COPY

Page 9-

File No. SG-0241

5

TROUBLE

OF EDID READING

Star t

Is Analog DDC OK?

Yes

Is HDMI DDC OK?

N0

N0

Support DDC1/2B

1. Analog cable ok?
2 .Check signal (U31 to P5)

3. Check U31 Voltage

4. Is protocol compliant?

Support DDC1/2B

1. Analog cable ok?

2. Check signal (U32 to P7)

3. Check signal (U34 to P9)

4. Is protocol compliant?

Yes

END

CONFIDENTIAL – DO NOT COPY

Page 9-

File No. SG-0241

6