Page 1
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373
www.visionfitness.com
©2006 Vision Fitness. All Rights Reserved. 11.06
AG18.46PRD
REV1
starts
vision
with a
it all
Assembly
Guide
R2750HRT
COMMERCIAL FITNESS BIKES
Page 2
TOOLS & PARTS INCLUDED
HARDWARE INCLUDED
Screwdriver
5mm T-Shaped Wrench
PARTS BOX
Console Mast Cover
Water Bottle
Heart Rate Chest Strap
Color-coded Hardware Bags
Pedals/Straps
Owner’s Guide
Assembly Guide
Warranty Card
4mm L-Shaped Wrench
5mm L-Shaped Wrench
15mm Pedal Wrench
ORANGE BAG
M8x65L Bolt
Quantity: 2
M8 x 20L Bolt
Quantity: 2
BLUE BAG
M8 x 15L Bolt
Quantity: 6
PINK BAG
M8 x 15L Bolt
Quantity: 2
M8 Lock Washer
Quantity: 4
M10 x 12L Set Screw
Quantity: 1
M8 Lock Washer
Quantity: 2
GREEN BAG
M8 x 20L Bolt
Quantity: 8
BLACK BAG
M6 x 55L Bolt
Quantity: 4
M6 Lock Washer
Quantity: 4
YELLOW BAG
M5 x 35L Bolt
Quantity: 2
M8 Lock Washer
Quantity: 8
M5 Lock Washer
Quantity: 2
Page 3
2
STEP
• Slide the console mast boot onto the
console mast.
• Unfold the wire harness and heart
rate wires located in the console mast
frame bracket. Attach the wire tie
coming from the bottom of the console
mast to the wire harness and heart
rate wires. Pull the wire tie with wire
harness and heart rate wires up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
• Secure the console mast to the
frame bracket with six bolts (M8x15L).
Tighten with the 5mm T-Shaped
wrench. Insert a set screw (M10x12L) to
the front edge of the mast and tighten
until snug with the 5mm T-shaped
wrench.
• Slide the console mast boot down
and snap it into place on the side cover.
BLUE BAG
3
STEP
• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two bolts (M8x15L). Tighten
with the 5mm T-Shaped wrench.
• Remove the four mounting screws from
the back of the console. Connect the
wire harness and heart rate wires that
come from the console mast into the
plugs located in the back of the console.
Attach the console to the mast with the
four screws removed earlier.
• Remove the battery cover on the back
side of the console. Plug in the 9-volt
battery. Re-attach the battery cover.
PINK BAG
1
STEP
• Install the rear foot with the four
lock washers (M8), two inside bolts
(M8x65L), and two outside bolts
(M8x20L). Tighten with the 5mm
T-Shaped wrench.
ORANGE BAG
Assembly
Guide
R2750HRT
COMMERCIAL FITNESS BIKES
1
STEP
4
STEP
• Remove the two socket head bolts
from the sliding seat adjustment bracket.
Slide the seat adjustment handle
between the teeth of the seat adjustment
bracket. Re-insert the two socket head
bolts and tighten with the 4mm Lshaped wrench.
• Attach the seat frame to the sliding
seat bracket using four lock washers
(M8) and four bolts (M8x20L) and the
5mm T-Shaped wrench.
• Connect Wires A on the seat
handlebar to Wires B on the sliding
seat bracket. Connect the wire harness
coming from the seat frame to the wire
harness in the handlebars. Attach the
seat handlebars to the sliding seat
bracket using four lock washers (M8)
and four bolts (M8x20L). Tighten with
the 5mm T-Shaped wrench.
GREEN BAG
2
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws
and bolts are in place and partially threaded in before completely tightening any ONE screw or bolt.
5
STEP
4
STEP
5
STEP
• Mount the seat bottom to the seat
frame with four bolts (M6x55L) and
four lock washers (M6). Tighten with
the 4mm L-shaped wrench.
BLACK BAG
3
STEP
Wires B
Wires A
6
STEP
• Attach the left and right pedals to
the left and right crank arms. Tighten
the pedals using the 15mm Pedal
Wrench.
• Secure the Accessory Tray to the
seat handlebar with two bolts
(M5x35L) and two lock washers
(M5). Be careful when inserting the
bolts to clear the wires inside the
handlebar to prevent damage.
Tighten with the screwdriver.
YELLOW BAG
6
STEP
Seat Bottom
Console Mast
Handlebar
Seat Handlebar
Seat Frame
Console Mast
Console Mast
Boot
Frame
Bracket
Rear Foot
Accessory
Tra y
Pedal
Sliding Seat
Bracket
Loading...