Viking FDFB5363L Installation Manual

Installation Guide
5 Series
Custom Panel
All Refrigerator/All Freezer
2
Table of Contents
Warnings & Important Information ____________________________________________________________________3 All Refrigerator/Freezer
Custom Grille Dimensions (Dual 36”) ________________________________________________________27 Cabinet Information _______________________________________________________________________________28 Custom Side Panel Dimensions _____________________________________________________________________30 Custom Panel General Information __________________________________________________________________31 Custom Door Panel Installation ____________________________________________________________________ 32 Custom Grille Installation ___________________________________________________________________________34 General Information _______________________________________________________________________________36
Unpacking & Moving ______________________________________________________________________38 Installation ________________________________________________________________________________________39
Hinge Adjustment_________________________________________________________________________39
Kickplate Installation_______________________________________________________________________42
Door Stop Adjustment_____________________________________________________________________42
Final Installation __________________________________________________________________________43 Performance Checklist _____________________________________________________________________________44 Control Panels ____________________________________________________________________________________45 Service & Registration______________________________________________________________________________46
3
IMPORTANT – Please Read and Follow
• Make sure that incoming voltage is the same as
unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product.
• To reduce the risk of fire, electrical shock, or injury
to persons, installation work and electrical wiring must be done by a qualified technician in accordance with all applicable codes and standards, including fire-rated construction.
• The installer should leave these instructions with
the consumer who should retain them for local inspector’s use and for future reference.
It is your responsibility to:
• Comply with installation specifications and
dimensions.
• Properly install unit.
• Remove any moldings or decorative panels that
prevent the unit from being serviced.
• Make sure that you have these materials (not
provided with your unit), which are necessary for proper installation:
• 1/4” (6 mm) copper tubing with shutoff valve
• 6 – #8 x 3” (7.6 cm) wood screws (longer screws may be required)
• 1– Saddle valve (DO NOT use self-piercing feature of the valve)
• Assure that floor will support unit, door panels and contents (approximately 1200 pounds [540 kg]).
• Provide a properly grounded electrical outlet.
• Assure that location will permit appliance doors to open a minimum of 90˚.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. ALWAYS read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the word “DANGER” or “WARNING.” These words mean:
Hazards or unsafe practices
which WILL result in severe personal
injury or death
DANGER
Hazards or unsafe practices
which COULD result in severe personal
injury or death
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
WARNING
IMPORTANT – Please Read and Follow!
4
A GFI
shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or
local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not
installed properly or do not meet the requirements below.
If the use of a GFI is required
, it should be:
• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles, switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
5
ELECTRICAL SHOCK HAZARD
Disconnect power or turn
power disconnect switch to OFF position before removing top grille. Failure to do so can result in death or electric shock.
WARNING
WARNING
TIP OVER HAZARD
Appliance is top heavy and tips easily when not completely installed. Keep
doors closed until appliance is completely installed and secured per installation instructions.
Use two or more people to move and install appliance. Failure to do so can result in death or serious injury.
Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent tipping. Use cardboard shipping material or plywood under unit until it is installed in the operating position to protect floor surface.
24”
(61.0 cm)
35”
(88.9 cm)
75–15/16”
(192.9 cm)
3–19/32”
(9.1 cm)
)
36”36”
(91.5 cm)(
91.5 cm
)
36”
(91.5 cm)
9–5/32”
(23.3 cm)
82–3/4”
(210.2 cm)
min.
to
84–1/16”
(213.5 cm)
max.
23-3/16”
(58.9 cm)
24”
(61.0 cm)
29”
(73.7 cm)
75–15/16”
(192.9 cm
)
3–19/32”
(9.1 cm)
30”30”
(76.2 cm)(76.2 cm)
30”
(76.2 cm)
9–5/32”
(23.3 cm)
82–3/4”
(210.2 cm)
min.
to
84–1/16”
(213.5 cm)
max.
23-3/16”
(58.9 cm)
Measurement varies
(locally supplied hardware)
Measurement varies
(locally supplied hardware)
Dimensions
6
30” All Refrigerator/Freezer
36” All Refrigerator/Freezer
7
Specifications
30 All Refrigerator/Freezer
Description FDFB/CFDFB FDRB/CFDRB
Overall width 30” (76.2 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-3/16” (58.9 cm)
To front edge of door trim: 24” (61.0 cm) Cutout width 30” (76.2 cm) Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. Cutout depth 24” (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product Maximum amp usage 9.1 amps 5.7 amps Inlet water requirements 1/4” copper tubing inlet
waterline; minimum 20 psi; N/A
maximum 120 psi Overall interior dimensions total capacity 15.9 cu. ft. (450 liters) 18.4 cu. ft. (522 liters) Maximum panel weight 50 lbs. (22.7 kg) Approximate shipping weight 445 lbs. (200.2 kg)
36 All Refrigerator/Freezer
Description FDFB/CFDFB FDRB/CFDRB
Overall width 36” (91.5 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-3/16” (58.9 cm)
To front edge of door trim: 24” (61.0 cm) Cutout width 36” (91.5 cm) Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. Cutout depth 24” (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product Maximum amp usage 9.5 amps 6.5 amps Inlet water requirements 1/4” copper tubing inlet
waterline; minimum 20 psi; N/A
maximum 120 psi Overall interior dimensions total capacity 20.0 cu. ft. (566 liters) 22.0 cu. ft. (623 liters) Maximum panel weight 60 lbs. (27.2 kg)
Approximate shipping weight 520 lbs. (234 kg)
*Note: Custom panel models fit flush in 25” (63.5 cm) deep cabinet openings. They can be installed in standard 24” (61.0 cm) deep openings. The door faces and top grille will protrude 3/4” (1.9 cm) into the room.
8
Cutout Dimensions
30” All Refrigerator/Freezer
24”
(61.0 cm)
82-7/8”
(210.5 cm) min.
anti-tip board &
opening height
84-1/16”
(213.5 cm) max.
anti-tip board &
opening height
See anti-tip board installation
(22.9 cm)
73-3/8”
(186.4 cm)
9”
Electric Outlet Location
6”
(15.2 cm)
9”
(22.9 cm)
Water Line Entry Area
Note: Shown for All Freezer only.
3
(76.2 cm)
0”
3-5/8”
(9.2 cm)
10-3/4”
(27.3 cm)
Optional floor
water line entry
5/8”
(1.5 cm)
7-5/8”
(19.4 cm)
3”
(7.6 cm)
30”
(76.2 cm)
6-3/4”
(17.1 cm)
10-1/2”
(26.7 cm)
5/8”
(1.5 cm)
5/8”
(1.5 cm)
1”
(2.5 cm)
One 2”x 4” mounting board
1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)
Note: If unit is installed deeper than 24” (61.0 cm), then shim
behind the mounting boards by the difference.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below opening height.
Note: Top of unit must be placed firmly under anti-tip board.
Anti-Tip Location
79-3/8”
(201.6 cm) min.
to bottom of anti-tip board
80-1/2”
(204.6 cm) max.
to bottom of anti-tip board
23”
(58.4 cm)
3-1/2”
(8.9 cm)
1-1/2”
(3.8 cm)
9
Anti-Tip Dimensions
30” All Refrigerator/Freezer
One 2”x4” mounting board 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)
Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below the opening height.
Note: Top of unit must be placed firmly under anti-tip board.
10
Cutout Dimensions
36” All Refrigerator/Freezer
24”
(61.0 cm)
82-7/8”
(210.5 cm) min.
anti-tip board &
opening height
84-1/16”
(213.5 cm) max.
anti-tip board &
opening height
3
(91.5 cm)
6”
See anti-tip board installation
9”
(22.9 cm)
73-3/8”
(186.4 cm)
5/8”
(1.5 cm)
Electric Outlet Location
6”
(15.2 cm)
9”
(22.9 cm)
Water Line Entry Area
Note: Shown for All Freezer only.
36”
7-5/8”
(19.4 cm)
3”
(7.6 cm)
(91.5 cm)
6-3/4”
(17.1 cm)
3-5/8”
(9.2 cm)
10-3/4”
(27.3 cm)
Optional floor
water line entry
10-1/2”
(26.7 cm)
5/8”
(1.5 cm)
(1.5 cm)
1”
(2.5 cm)
5/8”
One 2”x 4” mounting board
1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)
Note: If unit is installed deeper than 24” (61.0 cm), then shim
behind the mounting boards by the difference.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below opening height.
Note: Top of unit must be placed firmly under anti-tip board.
Anti-Tip Location
79-3/8”
(201.6 cm) min.
to bottom of anti-tip board
80-1/2”
(204.6 cm) max.
to bottom of anti-tip board
29”
(73.7 cm)
3-1/2”
(8.9 cm)
1-1/2”
(3.8 cm)
11
Anti-Tip Dimensions
36” All Refrigerator/Freezer
One 2”x4” mounting board 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)
Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below the opening height.
Note: Top of unit must be placed firmly under anti-tip board.
Dimensions
12
Dual 30” All Refrigerator/Freezer
3-1/2”
(8.9 cm)
75-15/16”
(192.9 cm)
30”
(76.2 cm)
29”
(73.7 cm)
30”
(76.2 cm)
29”
(73.7 cm)
9–5/32”
(23.3 cm)
29-1/2”
(74.9 cm)
Measurement varies
(locally supplied hardware)
1”
(2.54 cm)
between units
29-1/2”
(74.9 cm)
23-3/16”
(58.9 cm)
24-3/4”
(62.9 cm)
82–3/4”
(210.2 cm)
min.
to
84–1/16”
(213.5 cm)
max.
Dimensions
13
Dual 30” & 36” All Refrigerator/Freezer
3-1/2”
(8.9 cm)
75-15/16”
(192.9 cm)
30”
(76.2 cm)
29”
(73.7 cm)
36”
(91.5 cm)
35”
(88.9 cm)
9–5/32”
(23.3 cm)
29-1/2”
(74.9 cm)
Measurement varies
(locally supplied hardware)
1”
(2.54 cm)
between units
35-1/2”
(90.2 cm)
23-3/16”
(58.9 cm)
24-3/4”
(62.9 cm)
82–3/4”
(210.2 cm)
min.
to
84–1/16”
(213.5 cm)
max.
Dimensions
14
Dual 36” All Refrigerator/Freezer
35”
(88.9 cm)
3-1/2”
(8.9 cm)
75-15/16”
(192.9 cm)
36”
(91.5 cm)
36”
(91.5 cm)
Measurement varies
(locally supplied hardware)
35”
(88.9 cm)
9–5/32”
(23.3 cm)
82–3/4”
(210.2 cm)
min.
to
84–1/16”
(213.5 cm)
max.
35-1/2”
(90.2 cm)
1”
(2.54 cm)
between units
35-1/2”
(90.2 cm)
23-3/16”
(58.9 cm)
24-3/4”
(62.9 cm)
Specifications
15
Dual All Refrigerator/Freezer*
Description (2) 30 Units (1) 36 & (1) 30 Unit (2) 36” Units
Overall width 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-3/16” (58.9 cm)
To front edge of door trim: 24” (61.0 cm) Cutout width 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max. Cutout depth 24” (61.0 cm) min.** Electrical requirements (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
Maximum amp usage FDFB 30” - 9.1 amps
FDRB 30” - 5.7 amps FDFB 36” - 9.5 amps
FDRB 36” - 6.5 amps Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi; (All Freezer only) maximum 120 psi Overall interior dimensions
30” freezer 15.9 cu. ft. (450 liters) 30” refrigerator 18.4 cu. ft. (522 liters) 36” freezer 20.0 cu. ft. (566 liters) 36” refrigerator 22.0 cu. ft. (623 liters)
Maximum panel weight
30” freezer or refrigerator
50 lbs. (22.7 kg)
36” freezer or refrigerator
60 lbs. (27.2 kg)
Approximate shipping weight
30” freezer or refrigerator 445 lbs. (200.2 kg) 36” freezer or refrigerator 520 lbs. (234 kg)
*For installation of two units side-by-side, a separate grille kit accessory must be purchased.
**Note: Custom panel models fit flush in 25” (63.5 cm) deep cabinet openings. They can be installed in standard 24” (61.0 cm) deep openings. The door faces and top grille will protrude 3/4” (1.9 cm) into the room.
Loading...
+ 33 hidden pages