Viewsonic VS19173, VS19174, LS610WH, LS610HDH User manual

Page 1

LS610WH series/LS610HDH series

Projector User Guide

IMPORTANT: Please read this User Guide to obtain important informaon on installing and using your product in a safe manner, as well as registering your product for future service. Warranty informaon contained in this

User Guide will describe your limited coverage from ViewSonic Corporaon, which is also found on our web site at

hp://www.viewsonic.com in English, or in specic languages using the Regional selecon box in the upper right

corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS19173/VS19174

Model Name: LS610WH series/LS610HDH series

Page 2

Thank you for choosing ViewSonic®

As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic®, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic® product you have chosen will serve you well.

Once again, thank you for choosing ViewSonic®!

Page 3

Safety Precauons

Please read the following Safety Precauons before you start using the projector.

• Keep this user guide in a safe place for later reference.

• Read all warnings and follow all instrucons.

• Allow at least 20“ (50 cm) clearance around the projector to ensure proper

venlaon.

• Place the projector in a well-venlated area. Do not place anything on the projector that prevents heat dissipaon.

• Do not place the projector on an uneven or unstable surface. The projector may fall over, causing personal injury or projector malfuncon.

• Do not look straight at the projector lens during operaon. The intense light beam may damage your eyes.

• Always open the lens shuer or remove the lens cap when the projector lamp is on.

• Do not block the projecon lens with any objects when the projector is under

operaon as this could cause objects to become heated and deformed or even cause a re.

• The lamp becomes extremely hot during operaon. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

• Do not use lamps beyond the rated lamp life. Excessive use of lamps beyond the rated life could cause them to break on rare occasions.

• Never replace the lamp assembly or any electronic component unless the projector is unplugged.

• Do not aempt to disassemble the projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts.

• When moving the projector, be careful not to drop or bump the projector on anything.

• Do not place any heavy objects on the projector or connecon cables.

• Do not stand the projector on end vercally. Doing so may cause the projector to

fall over, causing personal injury or projector malfuncon.

• Avoid exposing the projector to direct sunlight or other sources of sustained heat. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including ampliers) that may increase the temperature of the projector to dangerous levels.

Page 4

• Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply and call your local service center to have the projector serviced.

• When the projector is under operaon, you may sense some heated air and odor from its venlaon grill. It is a normal operaon and not a defect.

• Do not aempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide and third blade are provided for your safety. If the plug does not t into your outlet, obtain an adapter and do not aempt to force the plug into the

outlet.

• When connecng to a power outlet, DO NOT remove the grounding prong.

Please ensure grounding prongs are NEVER REMOVED.

• Protect the power cord from being treaded upon or pinched, parcularly at the plug, and at the point where it emerges from the projector.

• In some countries, the voltage is NOT stable. This projector is designed to operate safely within a voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where voltage may uctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector, or uninterruptable power supply (UPS).

• If smoke, an abnormal noise, or a strange odor is present, immediately switch the projector o and call your dealer or ViewSonic®. It is dangerous to connue using the projector.

• Use only aachments/accessories specied by the manufacturer.

• Disconnect the power cord from the AC outlet if the projector is not being used

for a long period of me.

• Refer all servicing to qualied service personnel.

CAUTION: Possibly hazardous opcal radiaon is emied from this product. As

with any bright light source, do not stare into the beam, RG2 IEC 624715:2015.

Page 5

Safety Precauons - Ceiling Mounng

Please read the following Safety Precautions before you start using the projector.

If you intend to mount the projector on the ceiling, it is strongly recommended that you use a proper fitting projector ceiling mount kit and that you ensure it is securely and safely installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.

Page 6

Contents

Safety Precautions ....................................................... 3

Safety Precautions - Ceiling Mounting ......................... 5

Introduction ................................................................ 8

Package Contents ...................................................................................................8

Product Overview ............................................................................................ 9

Projector ........................................................................................................... 9

Remote Control................................................................................................11

Initial Setup ............................................................... 13

Choosing a Location ........................................................................................13

Projection Dimensions ....................................................................................14

LS610WH .........................................................................................................14

LS610HDH ........................................................................................................16

Mounting the Projector ..................................................................................18

Preventing Unauthorized Use .........................................................................19

Using the Security Slot .....................................................................................19

Using the Password Function ...........................................................................20

Locking the Control Keys ..................................................................................22

Making Connections .................................................. 23

Connecting to Power ............................................................................................23

Connecting to Video/Computer Sources .............................................................. 24

HDMI Connection .................................................................................................. 24

Connecting to Audio ............................................................................................. 24

Operation .................................................................. 25

Turning the Projector On/Off ...............................................................................25

Starting Up the Projector ...................................................................................... 25

Shutting Down the Projector ................................................................................. 26

Selecting an Input Source .....................................................................................27

Adjusting the Projected Image .............................................................................28

Fine-Tuning the Image Size and Clarity ................................................................. 28

Correcting Keystone .............................................................................................. 29

Hiding the Image ..................................................................................................30

Controlling the Projector through a LAN Environment ........................................31

Configuring the LAN Control Settings .................................................................... 31

Page 7

Menu Functions ........................................................ 33

General On-Screen Display (OSD) Menu Operation .........................................33

On-Screen Display (OSD) Menu Tree .................................................................... 34

DISPLAY Menu ......................................................................................................39

IMAGE Menu ........................................................................................................42

POWER MANAGEMENT Menu .............................................................................45

BASIC Menu .......................................................................................................... 48

ADVANCED Menu .................................................................................................51

SYSTEM Menu .......................................................................................................55

INFORMATION Menu ...........................................................................................57

Appendix ................................................................... 58

Specifications ........................................................................................................58

Projector Dimensions ............................................................................................ 59

Timing Chart .........................................................................................................59

Troubleshooting ...................................................................................................61

Common Problems ................................................................................................ 61

LED Indicators ........................................................................................................ 62

Light Source Information ...................................................................................... 63

Light Source Hour .................................................................................................. 63

Extending Light Source Life ................................................................................... 63

Regulatory and Service Information .......................... 64

Compliance Information ....................................................................................... 64

FCC Compliance Statement ................................................................................... 64

Industry Canada Statement ................................................................................... 64

CE Conformity for European Countries ................................................................. 64

Declaration of RoHS2 Compliance......................................................................... 65

Indian Restriction of Hazardous Substances ......................................................... 66

Product Disposal at End of Product Life ................................................................ 66

Customer Service .................................................................................................. 68

Limited Warranty .................................................................................................. 69

Mexico Limited Warranty ...................................................................................... 72

Page 8

Introduction

Package Contents

Projector Remote Control &

Batteries

NOTE: The power cord included in your package may vary depending on your country.

Please contact your local reseller for more informaon.

Power Cord Quick Start Guide

Page 9

Product Overview

EXIT

SOURCE

ENTER

BLANK

COLOR

MODE

Projector

Controls and Functions

Power key

Focus Ring Zoom Ring

Power Indicator Light

Temperature Indicator Light Light Source Indicator Light

Remote IR sensor

Projection Lens

Key Description

[ ] Power

[

/ / / ] Keystone

Keys

[

/ / / ]

Left/Right/Up/Down Menu/Exit Turns on or off the On-Screen Display (OSD) Menu. Source Displays the input source selection bar.

(Help)

Blank Hides the screen picture. Enter Enacts the selected On-Screen Display (OSD) Menu item when

[

] Corner Adjustment

Color Mode Displays the color mode selection bar.

Toggles the projector between standby mode and Power On.

Manually corrects distorted images resulting from an angled projection.

Selects the desired menu items and makes adjustments when the On-Screen Display (OSD) Menu is activated.

Displays the HELP menu.

the OSD Menu is activated. Displays the Corner Adj. menu when the OSD menu is not

activated.

Page 10

Connection Ports

LS610HDH

LS610WH

AUDIO OUTAUDIO IN RS232

AC Power Cord Inlet

Ceiling Mount Holes

5 6

Security Slot

Security Bar

Port Description

[1] CONTROL LAN port. [2] AUDIO OUT Audio signal output socket. [3] AUDIO IN Audio signal input socket.

[4] HDMI 1 HDMI port.

[5] HDMI 2 HDMI port. [6] USB 5V/1.5A OUT (Service) USB Type A port for power supply and serivce. [7] RS232 RS232 control port.

Adjuster Foot

1010

Page 11

Remote Control

Controls and Functions

Button

(Laser)

Description

Turns on/off the On-Screen Display (OSD) Menu or goes back to previous OSD Menu. Emits visible laser pointer light

for presentation purposes.

Button

On/ Off

COMP

HDMI 1

HDMI 2

Auto Sync Source

[ / / / ]

Keystone Keys

Enter

(Corner

adjustment)

Left/ Right

Up/ Down

Description

Toggles between standby

mode and Power On.

No function. Selects the source from the

HDMI 1 port for display. Selects the source from the

HDMI 2 port for display. No function.

Displays the source selection

bar.

Manually corrects distorted images resulting from an angled projection.

Enacts the selected OSD

Menu item. Displays the Corner Adj.

menu when the OSD menu is

not activated. Selects the desired menu items and makes adjustments.

Exit

Aspect

Freeze

Pattern

Blank PgUp (Page Up)/

PgDn (Page Down)

(Presentation

Timer) Eco Mode

(Volume Up)

(Volume

Down)

(Mute)

Color Mode

(INFORMATION) Network

Exits and saves menu settings.

Displays the aspect ratio selection bar.

Freezes the projected image. Displays embedded test

pattern.

Hides the screen picture. Operates your display

software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

NOTE: Only available when

a PC input signal is selected.

Displays the

Presentation Timer menu.

Selects the Eco mode. Increases the volume level.

Decreases the volume level.

Toggles audio between on

and off.

Displays the color mode selection bar. Magnifies the projected picture size.

Reduces the projected picture size.

Displays the INFORMATION

menu.

Displays the

LAN Control Settings menu.

Page 12

Remote Control Effective Range

To ensure proper function of the remote control

follow the steps below:

Approx. 30°

1. The remote control must be held at an angle

within 30° perpendicular to the projector’s IR remote control sensor(s).

2. The distance between the remote control and

the sensor(s) should not exceed 8 m (26 ft.)

NOTE:

Refer to the illustration for the location of the infrared (IR) remote control sensor(s).

Approx. 30°

Replacing the Remote Control Batteries

1. Remove the battery cover from the rear of the remote control by pressing the

finger grip and sliding it down.

2. Remove any existing batteries (if necessary) and install two AAA batteries.

NOTE: Observe the battery’s polarities as indicated.

3. Replace the battery cover by aligning it with the base and pushing it back into

position.

NOTE:

• Avoid leaving the remote control and batteries in excessive heat or a humid

environment.

• Replace only with the same or equivalent type recommended by the battery

manufacturer.

• Dispose of the used batteries according to the manufacturer’s instructions and

local environment regulations for your region.

• If the batteries are drained or if you will not be using the remote control for an

extended period of time, remove the batteries to avoid damage to the remote control.

Page 13

Initial Setup

This section provides detailed instructions for setting up your projector.

Choosing a Location

Personal preference and room layout will decide the installation location. Consider the following:

• Size and Position of your screen.

• Location of a suitable power outlet.

• Location and Distance between the projector and other equipment.

The projector is designed to be installed in one of the following locations:

1. Front

The projector is placed near the floor in front of the screen.

2. Front Ceiling

The projector is suspeneded upsidedown from the ceiling in front of the screen.

3. Rear Ceiling

The projector is suspended upside-down from the ceiling behind the screen.

NOTE:

4. Rear

The projector is placed near the floor behind the screen.

A special rear projection screen

is required.

NOTE:

A special rear projection screen

is required.

Page 14

Projection Dimensions

(a)

NOTE: See “Specifications” on page 58 for the native display resolution of this

projector.

LS610WH

• 16:10 Image on a 16:10 Screen

• 16:10 Image on a 4:3 Screen

(e)

(c)

(f)

(d)

(b)

NOTE: (e) = Screen

(f) = Center of Lens

16:10 Image on a 16:10 Screen

(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset

minimum maximum maximum

in. mm in. mm in. mm in. mm in. mm

30 762 34.75 883 41.71 1059 15.90 404 -1.67 -42

40 1016 46.34 1177 55.61 1412 21.20 538 -2.23 -57 50 1270 57.92 1471 69.51 1766 26.50 673 -2.78 -71 60 1524 69.51 1766 83.41 2119 31.80 808 -3.34 -85 70 1778 81.09 2060 97.31 2472 37.10 942 -3.90 -99 80 2032 92.68 2354 111.21 2825 42.40 1077 -4.45 -113

90 2286 104.26 2648 125.12 3178 47.70 1212 -5.01 -127 100 2540 115.85 2943 139.02 3531 53.00 1346 -5.56 -141 120 3048 139.02 3531 166.82 4237 63.60 1615 -6.68 -170 150 3810 173.77 4414 208.53 5297 79.50 2019 -8.35 -212 200 5080 231.70 5885 278.03 7062 106.00 2692 -11.13 -283 250 6350 289.62 7356 347.54 8828 132.50 3365 -13.91 -353 300 7620 347.54 8828 417.05 10593 159.00 4039 -16.69 -424

Page 15

16:10 Image on a 4:3 Screen

(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset

minimum maximum maximum

in. mm in. mm in. mm in. mm in. mm 30 762 32.79 833 39.34 999 15.00 381 -1.58 -40

40 1016 43.72 1110 52.46 1332 20.00 508 -2.10 -53 50 1270 54.65 1388 65.57 1666 25.00 635 -2.63 -67 60 1524 65.57 1666 78.69 1999 30.00 762 -3.15 -80 70 1778 76.50 1943 91.80 2332 35.00 889 -3.68 -93 80 2032 87.43 2221 104.92 2665 40.00 1016 -4.20 -107

90 2286 98.36 2498 118.03 2998 45.00 1143 -4.73 -120 100 2540 109.29 2776 131.15 3331 50.00 1270 -5.25 -133 120 3048 131.15 3331 157.38 3997 60.00 1524 -6.30 -160 150 3810 163.94 4164 196.72 4997 75.00 1905 -7.88 -200 200 5080 218.58 5552 262.30 6662 100.00 2540 -10.50 -267 250 6350 273.23 6940 327.87 8328 125.00 3175 -13.13 -333 300 7620 327.87 8328 393.45 9994 150.00 3810 -15.75 -400

NOTE:

It is recommended that if you intend to permanently install the projector, please physically test the projection size and distance using the actual projector in situ before you permanently install it.

Page 16

LS610HDH

• 16:9 Image on a 16:9 Screen

(b)

(a)

(d)

(c)

(e)

• 16:9 Image on a 4:3 Screen

(b)

(a)

(d)

(c)

(e)

NOTE: (e) = Screen

(f) = Center of Lens

(a)

(e)

(f)

(c)

(f)

(d)

(b)

(a)

(e)

(f)

(c)

(d)

(b)

16:9 Image on a 16:9 Screen

(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset

minimum maximum maximum

in. mm in. mm in. mm in. mm in. mm 30 762 34.07 865 40.88 1038 14.71 374 -1.25 -32

40 1016 45.42 1154 54.50 1384 19.61 498 -1.67 -42 50 1270 56.78 1442 68.13 1731 24.51 623 -2.08 -53 60 1524 68.13 1731 81.76 2077 29.42 747 -2.50 -64 70 1778 79.49 2019 95.38 2423 34.32 872 -2.92 -74 80 2032 90.84 2307 109.01 2769 39.22 996 -3.33 -85

90 2286 102.20 2596 122.64 3115 44.12 1121 -3.75 -95 100 2540 113.55 2884 136.26 3461 49.03 1245 -4.17 -106 120 3048 136.26 3461 163.51 4153 58.83 1494 -5.00 -127 150 3810 170.33 4326 204.39 5192 73.54 1868 -6.25 -159 200 5080 227.10 5768 272.52 6922 98.05 2491 -8.33 -212 250 6350 283.88 7211 340.65 8653 122.57 3113 -10.42 -265 300 7620 340.65 8653 408.79 10383 147.08 3736 -12.50 -318

Page 17

16:9 Image on a 4:3 Screen

(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset

minimum maximum maximum

in. mm in. mm in. mm in. mm in. mm

30 762 31.27 794 37.52 953 13.50 343 -1.15 -29

40 1016 41.69 1059 50.03 1271 18.00 457 -1.53 -39

50 1270 52.11 1324 62.54 1588 22.50 572 -1.91 -49

60 1524 62.54 1588 75.04 1906 27.00 686 -2.30 -58

70 1778 72.96 1853 87.55 2224 31.50 800 -2.68 -68

80 2032 83.38 2118 100.06 2541 36.00 914 -3.06 -78

90 2286 93.80 2383 112.56 2859 40.50 1029 -3.44 -87 100 2540 104.23 2647 125.07 3177 45.00 1143 -3.83 -97 120 3048 125.07 3177 150.09 3812 54.00 1372 -4.59 -117 150 3810 156.34 3971 187.61 4765 67.50 1715 -5.74 -146 200 5080 208.45 5295 250.14 6354 90.00 2286 -7.65 -194 250 6350 260.57 6618 312.68 7942 112.50 2858 -9.56 -243 300 7620 312.68 7942 375.22 9530 135.00 3429 -11.48 -291

NOTE:

It is recommended that if you intend to permanently install the projector, please physically test the projection size and distance using the actual

projector in situ before you permanently install it.

Page 18

Mounting the Projector

176.6

NOTE: If you buy a third-party mount, please use the correct screw size. Screw size

can vary depending on the thickness of the mounting plate.

1. To ensure the most secure installation, please use a ViewSonic® wall or ceiling

mount.

2. Ensure the screws used to attach a mount to the projector meet the following specifications:

• Screw type: M4

• Screw length: 12.8 mm ~ 15.8 mm

145.6

282.9

305.9

NOTE:

• Avoid installing the projector near a heat source.

• Keep at least a 10 cm gap between the ceiling and the bottom of the

projector.

Page 19

Preventing Unauthorized Use

The projector has several built-in security features to prevent theft, access, or accidental setting changes.

Using the Security Slot

To help prevent the projector from being stolen, use a security slot locking device to secure the projector to a fixed object.

Below is an example of setting up a security slot locking device:

NOTE: The security slot can also be used as a safety anchor if the projector is

mounted to the ceiling.

Page 20

Using the Password Function

To help prevent unauthorized access or use, the projector offers a password security option. The password can be set through the On-Screen Display (OSD)

Menu.

NOTE:

Make note of your password, and keep it in a safe place.

Setting a Password

1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings and

press Enter.

2. Highlight Power On Lock and select

On by pressing

/ .

3. As pictured to the right, the four arrow keys (

, , , ) represent 4 digits (1, 2, 3, 4). Press the arrow keys to enter a six digit password.

4. Confirm the new password by re-entering the new password. Once the password is set, the OSD Menu will return to the Security Settings page.

5. Press Exit to leave the OSD Menu.

NOTE:

Once set, the correct password must be entered every time the projector is

started.

2020

Page 21

Changing the Password

1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings >

Change Password.

2. Press Enter, the message, ‘INPUT CURRENT PASSWORD’ will appear.

3. Enter the old password.

 If the password is correct, the message, ‘INPUT NEW PASSWORD’ will

appear.

 If the password is incorrect, a password error message will appear for 5

seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can try again or press Exit to cancel.

4. Enter a new password.

5. Confirm the new password by re-entering the new password.

6. To leave the OSD Menu, press Exit.

NOTE:

The digits being input will display as asterisks (*).

Disabling the Password Function

1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings >

Power On Lock.

2. Press

/ to select Off.

3. The message, “Input Password” will appear. Enter the current password.

 If the password is correct, the OSD Menu returns to the Password page with

“Off” shown in the row of Power On Lock.

 If the password is incorrect, a password error message will appear for 5

seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can try again or press Exit to cancel.

NOTE:

Please keep the old password, as you will need it to reactivate the password function.

Page 22

Forgetting the Password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message, as pictured to the right, will appear for 5 seconds, and the message ‘INPUT PASSWORD’

follows.

You can retry or if you do not remember, you can use the “Password Recall Procedure”.

NOTE:

If you enter an incorrect password 5 times in succession, the projector will automatically shut down for a short time.

Password Recall Procedure

1. When the message ‘INPUT CURRENT

PASSWORD’ appears, press and hold Auto Sync for 3 seconds. The projector will display a coded number on the screen.

2. Write down the number and turn off your projector.

3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

Locking the Control Keys

With the control keys on the projector locked, you can prevent your settings from being changed accidentally (by children, for example).

NOTE:

When the Panel Key Lock is On, no control keys on the projector will operate except Power.

1. Press Menu to open the OSD Menu and go to: SYSTEM > Panel Key Lock.

2. Press

/ to select On.

3. Select Yes and press Enter to confirm.

4. To release panel key lock, press and hold

NOTE:

You can also use the remote control to enter the SYSTEM > Panel Key Lock menu and select Off.

on the projector for 3 seconds.

Page 23

Making Connections

This section guides you on how to connect the projector with other equipment.

Connecting to Power

1. Connect the power cord to the AC IN jack at the rear of the projector.

2. Plug the power cord into a power outlet.

NOTE: When installing the projector, incorporate a readily accessible disconnect

device in the xed wiring, or connect the power plug to an easily accessible outlet near the unit. If a fault should occur during operaon of the projector, use the disconnect device to switch o the power supply, or disconnect the power plug.

Page 24

Connecting to Video/Computer Sources

HDMI Connection

Connect one end of an HDMI cable to the HDMI port of your video device. Then connect the other end of the cable to the HDMI 1 or HDMI 2 port of your projector.

Connecting to Audio

The projector is equipped with speakers, however, you can also connect external speakers to the AUDIO OUT port of the projector.

NOTE:

The connection illustrations below are for reference only. The connecting jacks available on the projector vary with each projector model. Some cables may not be included with the projector. They are commercially available from electronics

stores.

The audio output is controlled by the projector’s Volume and Mute sengs.

Page 25

Operation

Turning the Projector On/Off

Starting Up the Projector

1. Press the Power buon to turn on the projector.

2. The light source will light up, and a “Power On/O Ring Tone” will play.

3. The Power Indicator Light stays green when the projector is On.

NOTE:

4. Turn on all of the connected equipment, i.e. notebook, and the projector will

start to search for an input source.

NOTE:

First Time Activation

If the projector is activated for the first time, select your OSD language following the on-screen instructions.

To maintain light source life, once you turn the projector On, wait at least ve (5) minutes before turning it o.

If the projector detects an input source, the source informaon will appear. If an input source is not detected, the message, ‘No Signal’ will appear.

Page 26

Shutting Down the Projector

1. Press the Power or O buon and a conrmaon message will appear to prompt

you to press the Power or O buon a second me. Addionally you can press any other buon to cancel.

NOTE:

If you do not respond in a few seconds aer the rst press, the message will

disappear.

2. Once the cooling process nishes, a “Power On/O Ring Tone” will play.

3. Disconnect the power cord from the power outlet if the projector will not be

used for an extended period of me.

NOTE:

• To protect the light source, the projector will not respond to commands during the cooling process.

• Do not unplug the power cord before the projector completely shuts down.

Page 27

Selecting an Input Source

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. The Input Source can also be manually selected by pressing one of the source selection buttons on the remote control, or by cycling through the available input sources.

To manually select the input source do the following:

1. Press Source, and a source selecon menu will appear.

2. Press

3. Once detected, the selected source informaon will be displayed on the screen

for a few seconds.

NOTE:

/ unl your desired signal is selected and press Enter.

If there are mulple devices connected to the projector, repeat steps 1-2 to search for another source.

Page 28

Adjusting the Projected Image

Adjusting the Projector's Height and Projection Angle

The projector is equipped with one (1) adjuster foot. Adjusting the foot will change the projector’s height and the vertical projection angle. Carefully adjust the feet to fine tune the projected image’s position.

Fine-Tuning the Image Size and Clarity

To adjust the projected image to the size that you need, rotate the Zoom Ring.

To improve the clarity of the image, rotate the Focus Ring.

Page 29

Correcting Keystone

EXIT

SOURCE

ENTER

BLANK

COLOR

MODE

Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection. To correct this, besides adjusting the height of the projector, you may also:

1. Use the keystone keys on the projector or remote control to display the keystone page.

2. Aer the keystone page is displayed, press

to correct keystoning at the top of the image. Press to correct keystoning at the boom of the image. Press to correct keystoning at the right side of the image. Press to correct keystoning at the le side of the image.

Page 30

Hiding the Image

In order to draw the audience’s full attention to the presenter, you can press Blank on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image.

CAUTION:

Do not block the projecon lens as this could cause the blocking object to

become heated and deformed or even cause a re.

Page 31

Controlling the Projector through a LAN Environment

The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network.

AUDIO OUTAUDIO IN RS232

Configuring the LAN Control Settings

• If you are in a DHCP environment:

1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port.

2. Open the OSD menu and go to the ADVANCED > LAN Control Settings menu. Press Enter to display the LAN Control Settings page. Or you can press Network to open the LAN Control Settings menu directly.

3. Highlight LAN Settings and press

4. Press

to highlight Apply and press Enter.

/ to select DHCP ON.

5. Please wait for around 15 - 20 seconds, and then re-enter the LAN Settings

page. The Projector IP Address, Subnet Mask, Default Gateway, DNS Server sengs will be displayed. Make note of the IP address displayed in the

Projector IP Address row.

NOTE:

Page 32

• If the Projector IP Address sll does not appear, contact your network

administrator.

• If the RJ45 cables are not properly connected, the Projector IP Address,

Subnet Mask, Default Gateway and DNS Server sengs will display 0.0.0.0. Make

sure the cables are properly connected and perform the procedures above again.

• If you need to connect to the projector in its standby mode, set

Standby LAN Control to On in the ADVANCED > LAN Control Settings menu.

• If you are in a non-DHCP environment:

1. Repeat steps 1-2 above.

2. Highlight LAN Settings and press

/ to select Static IP.

3. Contact your ITS administrator for informaon on the Projector IP Address,

Subnet Mask, Default Gateway, DNS Server sengs.

4. Press to select the item you want to modify and press Enter.

5. Press

/ to move the cursor and the press / to enter the value.

6. To save the sengs, press Enter. If you do not want to save the sengs, press

Exit.

7. Press

NOTE:

• If the RJ45 cables are not properly connected, the Projector IP Address,

• If you wish to connect to the projector in its standby mode, be sure you

to highlight Apply and press Enter.

Subnet Mask, Default Gateway, DNS Server sengs will display 0.0.0.0. Make

sure the cables are properly connected and perform the procedures above again.

have selected Static IP and obtained the Projector IP Address, Subnet Mask,

Default Gateway and DNS Server informaon when the projector is on.

Page 33

Menu Functions

This section will introduce the On-Screen Display (OSD) Menu and its options.

General On-Screen Display (OSD) Menu Operation

NOTE: The OSD screenshots in this manual are for reference only and may dier from

the actual design. Some of the following OSD sengs may not be available. Please refer to the actual OSD of your projector.

The projector is equipped with an On-Screen Display (OSD) Menu for making various adjustments. It can be accessed by pressing Menu on the projector or remote control.

1. Press / to select a main menu. Then press Enter or use / to access the sub-menu list.

2. Press or press / to adjust/select the seng.

NOTE:

/ to select the menu opon. Then press Enter to display its sub-menu,

Some sub-menu opons may have another sub-menu. To enter the respecve sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 34

On-Screen Display (OSD) Menu Tree

Main Menu Sub-menu Menu Opon

DISPLAY

Aspect Ratio Auto

4:3

16:9

16:10

Native

Keystone Vertical -40~40

Horizontal

Corner Adj. Top-Right 45°/90°

Top-Left

Bottom-Right

Bottom-Left

Zoom 0.8X ~2.0X

OverScan Off/1/2/3/4/5

IMAGE

3X Fast Input Inactive

Active

Color Mode Brightest

Presentation

Standard

Photo

Movie

User 1

User 2

Brightness 0~100 Contrast -50~50

Page 35

Main Menu Sub-menu Menu Opon

IMAGE

Color Temp. 9300K/7500K/6500K

Red Gain 0~100 Green Gain 0~100 Blue Gain 0~100 Red Offset -50~+50 Green Offset -50~+50 Blue Offset -50~+50

Advanced Color -50~50

Sharpness 0~31 Gamma 1.8/2.0/2.2/2.35/

2.5/Cubic/sRGB

Color Management Primary Color

Hue

Saturation

Gain

Reset Color Settings Reset

Cancel

Auto Power On Signal Disable/HDMI

CEC Disable/Enable Direct Power On Disable/Enable

Smart Energy Auto Power Off Disable/10 min/20

min/30 min

Sleep Timer Disable/30 min/1

hr/2hr/3 hr/4 hr/ 8 hr/12 hr

Power Saving Disable/Enable

Standby Settings Audio Pass Through Off/On

USB A Power On

Off

Page 36

Main Menu Sub-menu Menu Opon

BASIC

Audio Settings Mute Off/On

Audio Volume 0~20 Power On/Off Ring Tone On/Off

Presentation Timer Timer Period 1~240 m

Timer Display Always/1 min/2 min/

3 min/Never

Timer Position

Timer Counting Direction Count Down/Count Up

Sound Reminder On/Off

Start Counting/Off

Pattern Off

Test Card

Blank Timer

Disable/5 min/10 min/15 min/20 min/25 min/30 min

Top-Left/Bottom-Left/

Top-Right/Bottom-Right

ADVANCED

Message On

Off

Splash Screen Black

Blue

ViewSonic

HDR

(only for LS610HDH)

3D Settings 3D Format Auto

HDR Auto/SDR

EOTF Low/Mid/High

Off

Frame Sequential Frame Packing

Top-Bottom

Side-by-Side 3D Sync Invert Disable/Invert Save 3D Settings Yes/No

HDMI Settings HDMI Format Auto/RGB/YUV

HDMI Range

Auto/Enhanced/Normal

Page 37

Main Menu Sub-menu Menu Opon

ADVANCED

LAN Control Settings LAN Settings DHCP ON/Static IP

Projector IP Address Subnet Mask Default Gateway DNS Server Standby LAN Control Off/On Apply

Light Source Settings

Light Source Mode Normal/Eco/

Dynamic Black 1/

Dynamic Black 2

Reset Light Source Hours Reset/Cancel

Light Source Hours Information

Light Source Usage Time

Normal

Eco

Reset Settings Reset

Cancel

Dynamic Black 1

Dynamic Black 2

Page 38

Main Menu Sub-menu Menu Opon

SYSTEM

Language Multi-Language OSD Selection Projector Position Front Table

Rear Table

Rear Ceiling Front Ceiling

Menu Settings Menu Display Time 5 sec/10 sec/15 sec/20

sec/25 sec/30 sec Menu Position Center/Top-Left/

Top-Right/

Bottom-Left/

Bottom-Right

High Altitude Mode Off

Security Settings Change Password

INFORMATION

Power On Lock Off/On

Panel Key Lock Off

Remote Control Code Control Method RS232

Baud Rate 2400/4800/9600/14400/19200/38400/57600/

Source Color Mode

Resolution

Color System

IP address

MAC address

1/2/3/4/5/6/7/8

USB

115200

Firmware Version

3X Fast Input

S/N

Page 39

DISPLAY Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press the DISPLAY menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

/ to select the DISPLAY menu. Then press Enter or use / to access

or press / to adjust/select the seng.

NOTE:

Some sub-menu opons may have another sub-menu. To enter the respecve sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 40

Menu Option Description

Aspect Ratio

Auto

Scales an image proportionally to fit the projector’s native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image’s aspect ratio.

4:3

Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV, and 4:3 aspect DVD movies, as it displays them without aspect

alteration. 16:9

Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.

Keystone

Corner Adj.

Zoom

OverScan

16:10

Scales an image so that it is displayed in the center of the screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect, as it displays them without aspect alteration.

Native Projects an image as its original resolution and resizes it to fit within the display area. For input signals with lower resolutions, the projected image will be displayed in its original size.

Adjusts the keystoning situation where the projected image becomes a trapezoid due to angled projection.

Adjusts the shape and size of an image that is unevenly rectangular on all sides.

Magnifies the projected image and allows you to navigate the image.

Adjusts the overscan rate from 0% to 5%.

NOTE: This funcon is only available when a Composite Video or

HDMI input signal is selected.

Page 41

Menu Option Description

3X Fast Input

This function is favorable to frame rate reducing. Quick response time in native timing can be achieved. When enabled, the following settings will return to factory preset values: Keystone, Corner Adj., Aspect Ratio, OverScan, Zoom.

NOTE: This funcon is only available when a nave ming input

signal is selected.

Page 42

IMAGE Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press

the IMAGE menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu, or press / to adjust/select the seng.

/ to select the IMAGE menu. Then press Enter or use / to access

NOTE:

Some sub-menu opons may have another sub-menu. To enter the respecve sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 43

Menu Option Description

Color Mode

Brightest Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

Presentation

Designed for presentations under daylight environment to match PC and notebook coloring.

Standard

Designed for normal circumstances in a daylight environment.

Photo

Designed for photo viewing. Movie

For playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment.

User 1/User 2

Recalls the customized settings. After User 1/User 2 is selected, some of the sub-menus under the IMAGE menu can be adjusted, according to your selected input source.

Brightness

Contrast

The higher the value, the brighter the image. Adjust this option so the black areas of the image appear just as black and details in the dark area are more visible.

Use this to set the peak white level after you have previously adjusted the

Brightness setting.

Page 44

Menu Option Description

Color Temp.

Advanced

9300K

Images appear bluish white. 7500K

Images maintain a normal white appearance. 6500K

Images appear reddish white.

To set a custom color temperature, you can further adjust the following items:

Red Gain/Green Gain/Blue Gain

Adjusts the Contrast levels of Red, Green, and Blue.

Red Offset/Green Offset/Blue Offset

Adjusts the Brightness levels of Red, Green, and Blue. Color

A lower setting produces less saturated colors. If the setting is too high, colors will be overpowering and may appear unrealistic.

Reset Color Settings

Sharpness

A higher value will sharpen the image, while a lower value will soften the image.

Gamma

Gamma refers to the brightness level of the projector’s grayscale levels.

Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction. Select Primary Color first and adjust its range/values in Hue, Saturation and Gain.

Returns current image settings to the factory preset values.

Page 45

POWER MANAGEMENT Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

/ to select the POWER MANAGEMENT menu. Then press Enter or use

/ to access the POWER MANAGEMENT menu.

or press / to adjust/select the seng.

NOTE:

Some sub-menu opons may have another sub-menu. To enter the respecve sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 46

Menu Option Description

Auto Power On

Signal Selecting HDMI allows the projector to turn on automatically once the HDMI signal is fed through the HDMI cable.

CEC This projector supports CEC (Consumer Electronics Control) function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically.

NOTE:

• In order for the CEC funcon to work properly, make sure that the device is correctly connected to the HDMI input of the projector via an HDMI cable, and its CEC funcon is

turned on.

• Depending on the connected device, the CEC funcon may

not work.

Smart Energy

Standby Settings

Direct Power On Allows the projector to turn on automatically once power is fed through the power cord.

Auto Power Off

Allows the projector to turn off automatically after a set period of time once no input source is detected to prevent unnecessary waste of light source life.

Sleep Timer

Allows the projector to turn off automatically after a set period of time to prevent unnecessary waste of light source life.

Power Saving Lowers power consumption if no input source is detected. When Enable is selected, the projector will change to power saving mode after no signal is detected for five (5) minutes. This will also help prevent any unnecessary waste of light source life.

The functions below are available in standby mode (plugged in, but not turned on).

Audio Pass Through When selecting On, the projector outputs an audio signal when the Audio In and Audio Out sockets are correctly connected to a proper device.

Page 47

Menu Option Description

USB A Power

When On, the USB Type A port can supply power, and the

Control Method will automatically switch to RS232.

Page 48

BASIC Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press BASIC menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

/ to select the BASIC menu. Then press Enter or use / to access the

or press / to adjust/select the seng.

NOTE:

Some sub-menu opons may have another sub-menu. To enter the respecve sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 49

Menu Option Description

Audio Settings

Presentation Timer

Mute

Select On to temporarily turn off the projector’s internal speaker or the volume being output from the audio output jack.

Audio Volume

Adjusts the volume level of the projector’s internal speaker or the volume being output from the audio output jack.

Power On/Off Ring Tone Turns on/off the ring tone during the starting up and shutting down process.

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations.

Timer Period

Sets the time period. If the timer is already on, the timer will restart whenever the Timer Period is reset.

Timer Display Allows you to decide if you want the timer to show up on the screen for one of the following time periods:

 Always: Displays the mer on screen throughout the

presentaon me.

 1 min/2 min/3 min: Displays the mer on screen in the

last 1/2/3 minute(s).

 Never: Hides the mer throughout the presentaon me.

Timer Position Sets the timer position.

Timer Counting Direction Sets your desired counting direction between:

 Count Down: Decreases from the preset me to 0.  Count Up: Increases from 0 to the preset me.

Sound Reminder

Allows you to decide if you want to activate a sound reminder. Once enabled, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

Start Counting/Off Select Start Counting to activate the timer. Select Off to cancel

it.

Page 50

Menu Option Description

Pattern

Blank Timer

Message Splash Screen

Helps adjust the image size and focus, and checks for distortion in the projected image.

Allows the projector to return the image automatically after a period of time when there is no action taken on the blank

screen. To display the blank screen, press Blank on the projector or remote control.

NOTE: Do not block the projecon lens as this could cause the

blocking object to become heated and deformed or even cause a re.

Sets reminder messages, i.e. “Blank” message, On or Off. Selects which logo screen will appear during projector start-up.

Page 51

ADVANCED Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press access the ADVANCED menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

/ to select the ADVANCED menu. Then press Enter or use / to

or press / to adjust/select the seng.

NOTE:

Some sub-menu opons may have another sub-menu. To enter the respecve sub-menu, press Enter. Use / or / to adjust/select the seng.

Page 52

Menu Option Description

HDR

(only for LS610HDH)

3D Settings

HDR

The projector supports HDR/HLG imaging sources. It can automatically detect the dynamic range of the source, and optimize image gamma and color settings to reproduce contents under wide range of light conditions. You also select

SDR.

EOTF The projector can automatically adjust the brightness levels of your image according to the input source. Normally, the default setting “Mid” is recommended. If the brightness of the projected image is dark, please use “Low”. When giving priority to gradation property, please use “High”.

This projector features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view 3D images.

3D Format

The default setting is Auto and the projector automatically chooses an appropriate 3D format when detecting 3D contents. If the projector cannot recognize the 3D format, choose a 3D mode.

3D Sync Invert When you discover the inversion of the image depth, enable this function to correct the problem.

Save 3D Settings Saves current 3D settings. 3D settings will automatically be applied if the same resolution and input source are selected.

NOTE: When the 3D Sync funcon is on:

• The brightness level of the projected image will decrease.

• The Color Mode, Light Source Mode, Zoom, and OverScan

cannot be adjusted.

Page 53

Menu Option Description

HDMI Settings

LAN Control Settings

HDMI Format

Select a suitable color space according to the color space setting of the output device connected.

 Auto: Sets the projector to detect the color space seng

of the input signal automacally.

 RGB: Sets the color space as RGB.  YUV: Sets the color space as YUV.

HDMI Range Select a suitable HDMI color range according to the color range setting of the output device connected.

 Auto: Sets the projector to detect the HDMI range of the

input signal automacally.

 Enhanced: Sets the HDMI color range as 0 - 255.  Normal: Sets the HDMI color range as 16 - 235.

LAN Settings

 DHCP ON: Select this if you are in a DHCP environment

and Projector IP Address, Subnet Mask, Default Gateway,

DNS Server settings will be automatically retrieved.

 Static IP: Select this if you are in a non-DHCP environment

and make adjustments to below settings.

Projector IP Address Subnet Mask

Default Gateway DNS Server

Standby LAN Control Allows the projector to provide the network function in

standby mode. Apply Enacts the settings.

Only available when LAN Settings is set to Static IP. Use column and use / to adjust the value.

/ to select a

Page 54

Menu Option Description

Light Source Settings

Light Source Mode

 Normal: Provides full light source brightness.  Eco: Reduces light source power consumpon by 30% and

lowers brightness to decrease the fan noise.

 Dynamic Black 1: Reduces light source power

consumpon by up to 70% depending on the content brightness level.

 Dynamic Black 2: Reduces light source power

consumpon by up to 50% depending on the content brightness level.

Reset Light Source Hours Resets the light source timer after new light source is installed. For changing the light source, please contact qualified service

personnel.

Light Source Hours Information

 Light Source Usage Time: Displays the number of hours

the light source has been used.

Reset Settings

Returns all settings to the factory preset values. When using Reset Settings, the following settings will still remain: Language, Projector Position, High Altitude Mode, Security Settings, Remote Control Code, Zoom, Keystone, Control Method, USB A Power, Corner Adj. and Baud Rate, LAN Sttings, Light Source Hours Information.

Page 55

SYSTEM Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press

the SYSTEM menu.

3. Press / to select the menu opon. Then press Enter to display its sub-menu,

/ to select the SYSTEM menu. Then press Enter or use / to access

or press / to adjust/select the seng.

NOTE:

Some sub-menu opons may have another sub-menu. To enter the respecve

sub-menu, press Enter. Use

/ or / to adjust/select the seng.

Page 56

Menu Option Description

Language Projector Position Menu Settings

High Altitude Mode

Sets the language for the On-Screen Display (OSD) Menu. Selects a proper position for the projector. Menu Display Time

Sets the length of time the OSD Menu will remain active after your last interaction.

Menu Position

Sets the OSD Menu’s position. We recommend you use the High Altitude Mode when your

environment is between 1,501 m to 3,000 m above sea level, and ambient temperature is between 0°C–30°C.

NOTE:

• Do not use High Altude Mode if your environment is between 0 to 1,500 m, and the temperature is between 0°C to 35°C. If used, the projector will become over cooled.

• Using “High Altude Mode” may cause more operang noise, as the fan speed will be increased to improve cooling and performance.

Security Settings Panel Key Lock Remote Control Code

Control Method

See “Using the Password Function” on page 20. Locks the control keys on the projector. Sets the remote control code for this projector (between 1~8).

When multiple adjacent projectors are in operaon at the same

me, switching the codes can prevent interference from other remote controls. Aer the remote control code is set, switch to the same ID for the remote control to control this projector. To switch the code for the remote control, press ID set and the number buon corresponding to the remote control code together for 5 seconds or more. The inial code is set to 1. When the code is switched to 8, the remote control can control every projector.

NOTE: If dierent codes are set on the projector and remote

control, there will be no response from the remote control. When that happens, a message will display to remind you to switch the code for the remote control.

Allows you to select a preferred control port: through the RS232 port or the USB port. When selecting USB, USB A Power will be switched to Off automatically.

Baud Rate

Selects a baud rate that is identical with your computer’s so

that you can connect the projector using a suitable RS232 cable and control the projector with RS232 commands

Page 57

INFORMATION Menu

1. Press the Menu buon to display the On-Screen Display (OSD) Menu.

2. Press

/ to select the INFORMATION menu and display its contents.

Menu Option Description

Source Color Mode

Resolution

Color System

IP address

MAC address

Firmware Version 3X Fast Input S/N

Shows the current input source. Shows the selected mode in the IMAGE menu. Shows the native resolution of the input source.

Shows input system format. Shows the IP address of your projector. Shows the MAC Address of your projector. Shows the current firmware version. Shows whether the function is activated or not. Shows the serial number for this projector.

Page 58

Appendix

Specifications

Item Category LS610WH LS610HDH

Projector Type LED

Display Size 30” ~ 300”

Throw Ratio 1.37~1.64

(87”@2.56m)

1.30~1.56

(95”@2.74m)

Lens 1.2x Optical Zoom

Light Source

LED

Type

Display

1-CHIP DMD

System

Input Signal HDMI f

: 15K~102KHz, fv:23~120Hz, Pixel rate: 170MHz

Resolution Native 1280 x 800 1920 x 1080

Power Adapter

Operating conditions

Input Voltage AC 100-240V, 50/60 Hz (auto switch)

Temperature 0°C to 40°C (32°F to 104°F)

Humidity 10% to 90% (non-condensing)

Altitude 0 to 1,500 m at 0°C to 35°C

1,501 to 3,000 m at 0°C to 30°C

Storage

Temperature -20°C to 60°C (non-condensing)

conditions

Humidity 10% to 90% (non-condensing)

Altitude 0 to 40,000 ft sea level at -20°C to 30°C

Dimensions Physical

(W x D x H)

386 mm x 276 mm x 116 mm

(15.2” x 10.9” x 4.6” )

Weight Physical 5±0.2 kg (11 lbs)

Power

consumption

Please use the power adapter from ViewSonic® or an authorized source only.

The test condition follows EEI standards.

Off < 0.5W (Standby)

310W (Typical) 330W (Typical)

Page 59

Projector Dimensions

386 mm (W) x 276 mm (D) x 116 mm (H)

386 mm

BLANK

EXIT

ENTER

SOURCE

COLOR MODE

Timing Chart

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

VGA 640 x 480 4:3 60/72/75/85

-- 720 x 400 -- 70

SVGA 800 x 600 4:3 60/72/75/85/120**

XGA 1024 x 768 4:3 60/70/75/85/120** XGA 1152 x 864 4:3 75

HD 1280x 720 16:9 60/120

276 mm

76 mm

HDMI (PC)

116 mm

61 mm

WXGA 1280 x 768 15:9 60/60** WXGA 1280 x 800 16:10 60/75/85/120** WXGA 1366 x 768 16:9 59.7

Quad-VGA 1280 x 960 4:3 60/85

SXGA 1280 x 1024 5:4 60/75/85

SXGA+ 1400 x 1050 4:3 60

WXGA+ 1440 x 900 16:10 60**

UXGA 1600 x 1200 4:3 60

WSXGA+ 1680 x 1050 16:10 60**

VESA 1920 x 1080 16:9 60

WUXGA 1920 x 1200 16:10 60** MAC 13" 640 x 480 4:3 67 MAC 16" 832 x 624 4:3 75 MAC 19" 1024 x 768 4:3 75 MAC 21" 1152 x 870 4:3 75

NOTE: ** Reducing blanking.

Page 60

HDMI (Video)

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

HDTV (4K*) 3840 x 2160 16:9 24 / 25 / 30 / 50 / 60 HDTV (1080p) 1920 x 1080 16:9 24 HDTV (1080p) 1920 x 1080 16:9 50 / 60

HDTV (1080i) 1920 x 1080 16:9 50 / 60

HDTV (720p) 1280 x 720 16:9 50 / 60

SDTV (480p) 720 x 480 4:3 / 16:9 60 SDTV (576p) 720 x 576 4:3 / 16:9 50

SDTV (480i) 720 x 480 4:3 / 16:9 60

SDTV (576i) 720 x 576 4:3 / 16:9 50

NOTE: *Only supported by LS610HDH.

3D (HDMI signal included)

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

SVGA 800 x 600 4:3 60* / 120**

XGA 1024 x 768 4:3 60* / 120**

HD 1280 x 720 16:9 50* / 60* / 120**

WXGA 1280 x 800 16:9 60* / 120**

* 50Hz and 60Hz signals are supported for Side-by-Side, Top-Bottom, and Frame Sequential formats.

** 120 Hz signals are supported for Frame Sequential format only.

HDMI 3D

In Frame packing format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

1080p 1920 x 1080 16:9 23.98/24

720p 1280 x 720 16:9 50/59.94/60

In Side by side format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

1080i 1920 x 1080 16:9 50/59.94/60

720p 1280 x 720 16:9 50/59.94/60

In Top and Bottom format

1080i 1920 x 1080 16:9 23.98/24

720p 1280 x 720 16:9 50/59.94/60

Page 61

Troubleshooting

Common Problems

This section describes some common problems that you may experience when using the projector.

Problem Possible Solutions

The projector does not turn on • Ensure the power cord is properly aached to the

projector and to the power outlet.

• If the cooling process has not completed, please wait unl it has nished then try to turn on the projector again.

• If the above does not work, try another power outlet or another electrical device with the same power

outlet.

There is no picture • Ensure the video source cable is connected properly,

and that the video source is turned on.

• If the input source is not selected automacally, select the correct source with the Source key on either the projector or the remote control.

The image is blurred • Adjusng the Focus Ring will help correctly focus the

projecon lens.

• Ensure the projector and screen are aligned properly. If necessary, adjust the height of the projector as well as the projecon angle and direcon.

The remote control does not work

• Ensure there are no obstacles between the remote control and projector; and that they are within 8 m (26 ) of each other.

• The baeries may be out of power, please check and replace if necessary.

Page 62

LED Indicators

Light Status and Description

Power

Green

Flashing

Green Off Off Powering up Green Off Off Normal operation

Off Off Stand-by mode

Green

Flashing

Red Off Off Downloading

Green Green Green Burn in off

Off Off Normal power-down cooling

Light source

Green

Flashing

Off Off Red Light source error in normal operation

Green Off Red Color wheel start has failed

Off Red First light source-lit error cooling

Heating/Cooling

Off Red Off Fan 1 error (actual fan speed is outside the desired speed). Off Red Red Fan 2 error (actual fan speed is outside the desired speed).

Off Red Green Fan 3 error (actual fan speed is outside the desired speed). Off Red Orange Fan 4 error (actual fan speed is outside the desired speed).

Red

Flashing

Red Off Fan 5 error (actual fan speed is outside the desired speed).

Red

Flashing

Red Red Red Thermal sensor 1 open error (the remote diode has an

Red Red Green Thermal sensor 2 open error (the remote diode has an

Green Red Red Thermal sensor 1 short error (the remote diode has an

Off Red Green Thermal sensor 2 short error (the remote diode has an

Orange Red Red Temperature 1 error (over limited temperature). Orange Red Green Temperature 2 error (over limited temperature).

Off Green Red Fan IC #1 I2C connection error.

Red

Flashing

Off Fan 6 error (actual fan speed is outside the desired speed).

open-circuit condition).

Page 63

Light Source Information

This section will provided a better understanding of your projector’s light source.

Light Source Hour

When the projector is being used, the duration (in hours) of light source usage is automatically calculated by the built-in timer.

To obtain the light source hour information:

1. Press Menu to open the OSD Menu and go to: Advanced > Light Source Settings

> Light Source Hours Information.

2. Press Enter and the Light Source Hours Information page will appear.

3. Press Exit to leave the menu.

Extending Light Source Life

To prolong light source life, you can adjust the following settings in the OSD Menu.

Setting Light Source Mode

Setting the projector in Eco, Dynamic Black 1, or Dynamic Black 2 mode reduces system noise, power consumption, and extends the light sources operational life.

Light source Mode Description

Normal Provides full light source brightness.

Eco

Dynamic Black 1

Dynamic Black 2

Reduces light source power consumption by 30% and lowers brightness, and decreases fan noise.

Reduces light source power consumption by up to 70% depending on the content's brightness level.

Reduces light source power consumption by up to 50% depending on the content’s brightness level.

To set the Light Source Mode, open the OSD Menu and go to: Advanced >

Light Source Settings > Light Source Mode and press / to select and press Enter.

Setting Auto Power Off

This allows the projector to turn off automatically after a set period of time once no input source is detected.

Open the OSD Menu and go to: POWER MANAGEMENT > Smart Energy >

Auto Power Off and press

to disable or adjust the time.

Page 64

Regulatory and Service Informaon

Compliance Informaon

This secon addresses all connected requirements and statements regarding regulaons. Conrmed corresponding applicaons shall refer to nameplate labels and relevant markings on the unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operaon is subject to the following two condions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cauoned that changes or modicaons not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

CAN ICES-003(B) / NMB-003(B)

CE Conformity for European Countries

The device complies with the EMC Direcve 2014/30/EU and Low Voltage Direcve 2014/35/EU. Ecodesign Direcve 2009/125/EC.

Page 65

The following informaon is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Declaraon of RoHS2 Compliance

This product has been designed and manufactured in compliance with Direcve 2011/65/EU of the European Parliament and the Council on restricon of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Direcve) and is deemed to comply with the maximum concentraon values issued by the European Technical Adaptaon Commiee (TAC) as shown below:

Substance

Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01% Hexavalent Chromium (Cr6⁺) 0.1% < 0.1% Polybrominated biphenyls (PBB) 0.1% < 0.1% Polybrominated diphenyl ethers

(PBDE) Bis (2-ethylhexyl) phthalate

(DEHP) Butyl benzyl phthalate (BBP) 0.1% < 0.1% Dibutyl phthalate (DBP) 0.1% < 0.1% Diisobutyl phthalate (DIBP) 0.1% < 0.1%

Proposed Maximum

Concentraon

0.1% < 0.1%

Actual Concentraon

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Direcves as noted below. Examples of exempted components

are:

• Mercury in cold cathode uorescent lamps and external electrode uorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

 Short length (500 mm): maximum 3.5 mg per lamp.  Medium length (> 500 mm and 1,500 mm): maximum 5 mg per lamp.  Long length (> 1,500 mm): maximum 13 mg per lamp.

• Lead in glass of cathode ray tubes.

• Lead in glass of uorescent tubes not exceeding 0.2% by weight.

• Lead as an alloying element in aluminum containing up to 0.4% lead by weight.

• Copper alloy containing up to 4% lead by weight.

Page 66

• Lead in high melng temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

• Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

Indian Restricon of Hazardous Substances

Restricon on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentraons exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exempons set in Schedule 2 of the Rule.

Product Disposal at End of Product Life

ViewSonic® respects the environment and is commied to working and living green. Thank you for being part of Smarter, Greener Compung. Please visit the

ViewSonic® website to learn more.

USA & Canada:

hps://www.viewsonic.com/us/company/green/go-green-with-viewsonic/#recycle-program

Europe:

hps://www.viewsoniceurope.com/eu/support/call-desk/

Taiwan:

https://recycle.epa.gov.tw/

Page 67

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microso, Windows, and the Windows logo are registered trademarks of Microso Corporaon in the United States and other countries.

ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic® Corporaon.

VESA is a registered trademark of the Video Electronics Standards Associaon. DPMS, DisplayPort, and DDC are trademarks of VESA.

ENERGY STAR® is a registered trademark of the U.S. Environmental Protecon Agency (EPA).

As an ENERGY STAR® partner, ViewSonic® Corporaon has determined that this product meets the ENERGY STAR® guidelines for energy eciency.

Disclaimer: ViewSonic® Corporaon shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequenal damages resulng from furnishing this material, or the performance or use of this product.

In the interest of connuing product improvement, ViewSonic® Corporaon reserves the right to change product specicaons without noce. Informaon in this document may change without noce.

No part of this document may be copied, reproduced, or transmied by any means, for any purpose without prior wrien permission from ViewSonic® Corporaon.

LS610WH_LS610HDH_UG_ENG_1a_20221103

Page 68

Customer Service

For technical support or product service, see the table below or contact your

reseller.

NOTE: You will need the product’s serial number.

Country/ Region Website Country/ Region Website

Asia Pacic & Africa

Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/

中国 (China)

Hong Kong (English) www.viewsonic.com/hk-en/ India www.viewsonic.com/in/

Indonesia www.viewsonic.com/id/ Israel www.viewsonic.com/il/

日本 (Japan)

Malaysia www.viewsonic.com/my/ Middle East www.viewsonic.com/me/

Myanmar www.viewsonic.com/mm/ Nepal www.viewsonic.com/np/

New Zealand www.viewsonic.com/nz/ Pakistan www.viewsonic.com/pk/

Philippines www.viewsonic.com/ph/ Singapore www.viewsonic.com/sg/

臺灣 (Taiwan)

Việt Nam

www.viewsonic.com.cn

www.viewsonic.com/jp/ Korea www.viewsonic.com/kr/

www.viewsonic.com/tw/

www.viewsonic.com/vn/ South Africa & Maurius www.viewsonic.com/za/

香港 (繁體中文)

ประเทศไทย

www.viewsonic.com/hk/

www.viewsonic.com/th/

Americas

United States www.viewsonic.com/us Canada www.viewsonic.com/us

Lan America www.viewsonic.com/la

Europe

Europe www.viewsonic.com/eu/ France www.viewsonic.com/fr/

Deutschland www.viewsonic.com/de/ Қазақстан www.viewsonic.com/kz/

Россия www.viewsonic.com/ru/ España www.viewsonic.com/es/

Türkiye www.viewsonic.com/tr/ Україна www.viewsonic.com/ua/

United Kingdom www.viewsonic.com/uk/

Page 69

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defecve in material or workmanship during the warranty period, ViewSonic® will, at its sole opon, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

Limited Three (3) year General Warranty:

Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp from the date of the rst consumer purchase.

Other regions or countries: Please check with your local dealer or local ViewSonic® oce for the warranty informaon.

Limited One (1) year Heavy Usage Warranty:

Under heavy usage sengs, where a projector’s use includes more than fourteen (14) hours average daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the rst consumer purchase; Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the rst consumer purchase. Other regions or countries: Please check with your local dealer or local ViewSonic® oce for the warranty informaon. Lamp warranty subject to terms and condions, vericaon and approval. Applies to manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied, or

removed.

Page 70

2. Damage, deterioraon, or malfuncon resulng from:

 Accident, misuse, neglect, re, water, lightning, or other acts of nature,

unauthorized product modicaon, or failure to follow instrucons supplied with the product.

 Operaon outside of product specicaons.  Operaon of the product for other than the normal intended use or not

under normal condions.

 Repair or aempted repair by anyone not authorized by ViewSonic®.  Any damage of the product due to shipment.  Removal or installaon of the product.  Causes external to the product, such as electric power uctuaons or

failure.

 Use of supplies or parts not meeng Viewsonic’s specicaons.  Normal wear and tear.  Any other cause which does not relate to a product defect.

3. Removal, installaon, and set-up service charges.

How to get service:

1. For informaon about receiving service under warranty, contact ViewSonic®

Customer Support (Please refer to the “Customer Support” page). You will need to provide your product’s serial number.

2. To obtain warranted service, you will be required to provide: (a) the original dated sales slip, (b) your name, (c) your address, (d) a descripon of the problem, and (e) the serial number of the product.

3. Take or ship the product, freight prepaid, in the original container to an authorized ViewSonic® service center or ViewSonic®.

4. For addional informaon or the name of the nearest ViewSonic® service center, contact ViewSonic®.

Limitaon of implied warranes:

There are no warranes, express or implied, which extend beyond the descripon contained herein including the implied warranty of merchantability and tness for a parcular purpose.

Page 71

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic® shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of me, loss of prots, loss of business opportunity, loss of goodwill, interference with business relaonships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequenal or otherwise.

3. Any claim against the customer by any other party.

Eect of state law:

This warranty gives you specic legal rights, and you may also have other rights which vary from local authority. Some local governments do not allow limitaons on implied warranes and/or do not allow the exclusion of incidental or consequenal damages, so the above limitaons and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty informaon and service on ViewSonic® products sold outside of the U.S.A. and Canada, contact ViewSonic® or your local ViewSonic® dealer.

The warranty period for this product in mainland China (Hong Kong, Macao, and Taiwan Excluded) is subject to the terms and condions of the Maintenance Guarantee Card.

For users in Europe and Russia, full details of warranty provided can be found at:

http://www.viewsonic.com/eu/ under “Support/Warranty Informaon”.

Projector Warranty Term Template In UG VSC_TEMP_2005

Page 72

Mexico Limited Warranty

ViewSonic® Projector

What the warranty covers:

How long the warranty is eecve:

3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the rst consumer purchase.

Lamp warranty subject to terms and condions, vericaon and approval. Applies to manufacturer’s installed lamp only.

All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty excludes and does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioraon, or malfuncon resulng from:

 Accident, misuse, neglect, re, water, lightning, or other acts of nature,

unauthorized product modicaon, unauthorized aempted repair, or failure to follow instrucons supplied with the product.

 Any damage of the product due to shipment.  Causes external to the product, such as electrical power uctuaons or

failure.

 Use of supplies or parts not meeng ViewSonic®’s specicaons.  Normal wear and tear.  Any other cause which does not relate to a product defect.

3. Any product exhibing a condion commonly known as “image burn-in” which results when a stac image is displayed on the product for an extended period of me.

4. Removal, installaon, insurance, and set-up service charges.

Page 73

How to get service:

For informaon about receiving service under warranty, contact ViewSonic® Customer Support (Please refer to the aached “Customer Service” page). You will need to provide your product’s serial number, so please record the product informaon in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim.

For Your Records

Product Name: Model Number:

Document Number: Serial Number:

Purchase Date: Extended Warranty Purchase? (Y/N)

If so, what date does warranty expire?

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a descripon of the problem, and (e) the serial number of the product.

2. Take or ship the product, in the original container packaging, to an authorized ViewSonic® service center.

3. Round trip transportaon costs for in-warranty products will be paid by ViewSonic®.

Limitaon of implied warranes:

There are no warranes, express or implied, which extend beyond the descripon contained herein including the implied warranty of merchantability and tness for a parcular purpose.

Exclusion of damages:

ViewSonic®’s liability is limited to the cost of repair or replacement of the product. ViewSonic® shall not be liable for:

2. Any other damages, whether incidental, consequenal or otherwise.

3. Any claim against the customer by any other party.

4. Repair or aempted repair by anyone not authorized by ViewSonic®.

Page 74

Contact Informaon for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporavo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 hp://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.P: 83140 Tel: 01-66-22-14-9005 E-Mail: [email protected]

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio: 29 SUR 721 COL. LA PAZ 72160 PUEBLA, PUE. Tel: 01(52).222.891.55.77 CON 10 LINEAS E-Mail: [email protected]

Chihuahua:

Soluciones Globales en Computación C. Magisterio # 3321 Col. Magisterial Chihuahua, Chih. Tel: 4136954 E-Mail: [email protected]

Distrito Federal:

QPLUS, S.A. de C.V. Av. Coyoacán 931 Col. Del Valle 03100, México, D.F. Tel: 01(52)55-50-00-27-35 E-Mail : [email protected]

Villahermosa:

Compumantenimietnos Garanzados, S.A. de C.V. AV. GREGORIO MENDEZ #1504 COL, FLORIDA C.P. 86040 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09 E-Mail: [email protected]

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419 ENTRE PINZÓN Y ALVARADO Fracc. Reforma C.P. 91919

Tel: 01-22-91-00-31-67

E-Mail: [email protected]

Cuernavaca:

Compusupport de Cuernavaca SA de CV Francisco Leyva # 178 Col. Miguel Hidalgo C.P. 62040, Cuernavaca Morelos Tel: 01 777 3180579 / 01 777 3124014 E-Mail: [email protected]

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V. Av. Niños Héroes # 2281 Col. Arcos Sur, Sector Juárez 44170, Guadalajara, Jalisco Tel: 01(52)33-36-15-15-43 E-Mail: [email protected]

Guerrero Acapulco:

GS Computación (Grupo Sesicomp) Progreso #6-A, Colo Centro 39300 Acapulco, Guerrero

Tel: 744-48-32627

MERIDA:

ELECTROSER Av Reforma No. 403Gx39 y 41 Mérida, Yucatán, México CP97000 Tel: (52) 999-925-1916 E-Mail: [email protected]

Tijuana:

STD

Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembr Tijuana, Mexico

Projector Mexico Warranty Term Template In UG VSC_TEMP_2006

Monterrey:

Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. Bernardo Reyes, CP 64280 Monterrey N.L. México Tel: 8129-5103 E-Mail: [email protected]

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y SERVICIO, S.A. de C.V. Murguía # 708 P.A., Col. Centro, 68000, Oaxaca Tel: 01(52)95-15-15-22-22 Fax: 01(52)95-15-13-67-00 E-Mail. [email protected]

FOR USA SUPPORT:

ViewSonic® Corporaon 381 Brea Canyon Road, Walnut, CA. 91789 USA

Tel: 800-688-6688

E-Mail: hp://www.viewsonic.com

Page 75