Thank you for selecting ViewEra's high performance, multi-function LCD monitor .
product life, please read and follow the instructions before using it, and comply with the following safety cautions:
1 To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor case.
2 ) Keep the manual for future use.
3 Follow all the warnings and instructions strictly on the manual.
4 It is high dangerous voltage inside the product. Do not attempt to repair the product by yourself.
5 This monitor is equipped with a three-wire grounding type of power source indicated on the marking label. If the plug can't
be inserted iinto. the outlet, please contact a technician for replacing the original outlet to keep the safeguard measure in effect.
Do not allow water or other liquids to spill on or into the LCD monitor
6
7 Don't use the attachments which are not recommended by the monitor manufacturer as they may cause hazards.
8 Do not rest anything on the power cord.. If the power cord is damaged, do not use the monitor.
9 Don't overload outlets or extend cords as it can result in fire or electric shock.
10 If you want to disconnect the power cord from the product, be sure to grasp the plug, not the cable.
11 Unplug the monitor when it is going to be left unused for an extended period of time.
12 Place the monitor in a place of good ventilation, low humidity and dust environment, and avoid direct sunlight.
13 The openings on the back cover are designed for ventilation. To prevent overheating, do not block or cover these openings.
To ensure your safety and extend
Page 5
surface .Don't place the machine near or over heat source or place in built-in installation.
141 Unplug your monitor from the electric outlet before any service is performed..
15 Don't use solvents, like ethyl alcohol, acetone, ethanol and hexane to clean the surface of LCD screen.
16 Don't place the machine near water source such as bathtub, washbowl, sink, laundry tub, swimming pool, etc.
17 The LCD panel is made of glass, the surface of screen is easy to be frayed. Don't knock or press on the surface of
the panel with finger or other objects, otherwise it can result in damage to the panel.
18 Don't remove or open the cover by yourself. It may expose you to dangerous voltage or other hazards .
19 Do not put the monitor at the place where user is subject to mal-operation.
20 High temperatures can cause problems. Keep the monitor away from heaters, stoves, fireplaces, etc.
21 Please keep the foam and box of package for future use. These are ideal packing material for transportation..
22 Unplug this machine from the outlet and refer servicing to qualified service personnel under the following conditions:
A. The power cord is frayed or damaged.
B. The monitor has been dropped or the cabinet has been damaged.
C. When the performance of the monitor deteriorates distinctly.
Support HDCP (High-bandwith Digital Content Protection)
Featured built-in speakers, they will give you audio enjoyment and save your space.
With multiple connectors, you may directly connect it to your DVD player, VCR or game console, etc. The Components
Video input connectors let you enjoy beautiful image quality. The monitor can be used as a computer monitor with
VGA or HDMI connectors, which can display at resolution of 1680X1050.
Fast response time will completely eliminate shadow of picture. Watching films and playing games can be
more smooth.
Wide viewing angle, highe brightness, highe contrast and lower power consumption
Intelligent image mode and sound mode can offer you intelligent audio and visual effects.
Built-in digital comb filter makes image more clear. The internal 3D De-Interlace technology
can totally eliminate the screen dithering caused by interlace signals.
With sleep timer, you can set time to turn off. It will be turned off in state of no signals, too.
Convenient use with a remote cotrol
Auto-setup function help you set the image to best performance
Auto color balance adjustment makes your monitor to display an optimal color setting for different kinds
of display device.
Advanced noise reduction technology can greatly eliminate background noise and make the picture clear.
4
Page 7
2. Package Contents
Unpack the package and check if you have the following items.
TFT-LCD monitor (19 inch for V193 series; 22 inch for V220 series)
VGA signal cable
Audio cable
Power cord
Remote control
User manual
If any of the items is missing, please contact with your dealer at which you purchased the monitor.
5
Page 8
3. Installation
Note: Disconnect the power plug while installing the monitor. Plug the power plug after cable connections are done.
You can find more connectors when you take off the cover board on the left of the rear cover [Fig.2]
Component connection [Fig.1]
Connect Y, Pb/Cb, Pr/Cr Video Out on
a video player to the monitor Y, Pb/Cb,
Pr/Cr Video In, and then connect Audio
Out left and right on a video player to
the monitor Audio In left and right.
AV connection [Fig.2]
You can also watch video by connecting
composite AV connectors. Connect one end
of of the cable to Audio/ Video Out on a
Audio Input
video player, and the other end to to the
Audio/ Video In on the monitor.
Computer connection [Fig.2]
You can use a VGA or HDMI Male-to-DVI
Male cable to connect the monitor to your
computer. For PC audio, you can plug one
R L
end of the audio cable to PC Audio on the
monitor, and then plug the other end into the audio
input on your computer.
Y Pb Pr Input
Pr/Cr P b/Cb Y
Connect to DVD
TV Video output
TV Audio output
Connect to VCR
Power Supply
CATV
Fig.1
6
Page 9
Power Cord Connection
Plug one end of the power cord into the monitor power jack and then plug the other end into the outlet.
Earphone connection [Fig.2]
When you enjoy music with earphone, you can insert the plug of earphone into earphone jack on the monitor.
Then the monitor will automatically mute the speakers.
Base installation
Please refer to Fig.3, Fig.4
Note: HDMI connector can
recognize DVI signal via a
HDMI Male-to-DVI Male cable.
Right
Left
OR
Audio
Audio
HDMI
Connect to PC
VGA
S-Video
Video
Connect to DVD/VCR/VCD etc
Fig.2
7
Page 10
4. Front Panel Control Keys
SOURCE
POWER
CH+
VOL+
VOL-
MENU
3
5
CH-
6
4
7
8
1 2
1) Power Indicator
2) IR Sensor: It is to receive signals from remote contorl.
3) Signal Source: press this key to enter the menu of signal source and choose signal source.
4) Menu: press this key to enter main menu
5) CH+/CH-: Press these two keys to adjust the options you need under OSD operation.
6) VOL+/VOL-: Press these two keys to adjust the analog value under OSD operation.
7) Power On/Off
8) Earphone Socket: The TV speakers will be shut off when earphone is plugged into this socket.
8
Page 11
5. Remote Control
9
Power
Numerical key
Smart sound
Menu
Volume
Info
Time
DCDi(optional)
Color(optional)
POWER
ABC
123
JKL
456
STUVWX
789
0
MENU
V
O
L
INFO
DCDi COLOR P/N AUDIO
DEF
MNO
SMART S SMART P
OK
MUTE
GHI
PQR
YZ
SOURCE
P
16:9
M
A
R
G
O
R
Remote Control
Mute
Program list(optional)
Digit
Smart image
Source
OK
Cursor key
Channel
Switch16:9/4:3(optional)
Return
NICAM(optional)
Color system(optional)
Key
Power
Info
Mute
Timer
Turn on or standby
System information display switch
Mute sound; press again to restore sound
Time setting button
Function
Numerical key Number input button
Program list
Digit
Cursor
OK
Channel
Volume
Scan or set program list
Change digit
Up or down cursor button: function seclect;
left or right cursor button: analog add or reduce.
Confirm actions
Select higher or lower channel number
Increase or decrease volume
MenuPress this menu button to display menu
Source
Smart sound
Return
Smart image
Press this button to display signal source
selection menu
Intelligent sound mode selection
Press this button to return to last
Intelligent image mode selection
channel
Page 12
6. Basic Operations
Power On
Plug power cord into the outlet and press '' '' key on the front panel or press ''Power'' key on the remote
control to turn on the monitor.
Signal Source Selection
Press ''SOURCE'' key either on the remote control or on the front panel. ''INPUTSOURCE''
will be displayed on the screen. Then press ''Up/Down'' key on remote control or "CH+/CH-" key on the
front panel to choose the signal source such as TV(optional) AV, S-VIDEO, YPBPR, PC, HDMI. Press
''OK'' key on the remote control or "MENU" key on the front panel to switch the signal source.
TV
AV
SVIDEO
YPBPR
PC
HDMI
10
Page 13
OSD Menu
Press ''MENU'' key on the remote control or on the front panel. The
monitor will display the main menu.
1. Press ''Left/Right'' key on the remote control or ''VOL+/VOL-''key
on the front panel to select the submenu, which
includes
PICTURE SOUND ADVANCE SYSTEM
TV-CHANNEL (optional).
2. Press ''Down''key on the remote control or ''CH-'' on the front panel
to enter the submenu.
3. Press ''Up/Down'' key on the remote control or ''CH+/CH-'' on the
front panel to select what is needed to adjust in submenu.
4. Press ''Left/Right'' key on the remote control or ''VOL+/ VOL-''on the
front panel to adjust the value or setting.
5. Press ''Menu'' key to exit the main menu when the monitor displays
Main Menu. Press ''Menu'' key to return to previous menu when the
monitor displays the sub-menu. Press ''Source''key to display the signal source menu.
6. During the operation, the selections which can not be adjusted at current mode will be hidden automatically and the
color of the selections will be changed into gray.
PICTURE MOD E
CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
BLACK LIGHT
COLOR TONE
PICTURE SELECT:ADJUST:
PERSONAL
WARM
EXIT:
MENU
61
41
50
46
48
50
11
Page 14
Picture Adjustment
Select to enter the Picture Adjustment submenu. Press "Up/Down" key on the remote control or the key " CH+/CH-" on
the front panel to choose what you need. Press the "Left /Right "key on the remote control or the" VOL+/VOL-" key on the
front panel to adjust analog value or state (see below table).
Attention
1. The Hue function is available only for NTSC system.
2. The value adjusted by user, such as Contrast, Brightness,
Saturation, Hue, and Sharpness, will be saved automatically
by the machine as user's defined mode.
3. You can adjust Brightness, Contrast, Sharpness, Black Light,
only in personal model.
Remote Control Shortcut Keys
Smart Picture : SMART P
Press SMART P key on the remote control. You can switch
the function among the "STANDARD", "DYNAMIC", "SOFT",
"PERSONAL" four states .
16:9: Press 16:9 key on the remote control, you can switch the mode among the "FULL", "ZOOM", "ZOOM2",
"NORMAL" and "PANORAMA"
PICTURE MOD E
CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
BLACK LIGHT
COLOR TONE
PICTURE SELECT:ADJUST:
PERSONAL
WARM
EXIT:
MENU
61
41
50
46
48
50
12
Page 15
Option
PICTURE MODE
Function
Select picture mode
Description
"STANDARD", "DYNAMIC", "SOFT", "PERSONAL" four states.
CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
BLACK LIGHT
COLOR TONE
13
Adjust the contrast of whole
picture
Adjust brightness and blackness
of whole picture
Adjust the hue of whole picture
Adjust the saturation of whole
picture
Adjust the sharpness of whole
picture
Adjust the black light of whole
picture
Select color tone mode of the
picture
Increasing analog value increases Contrast;
Decreasing analog value decreases Contrast(0-100).
Increasing analog value increases brightness;
Decreasing analog value decreases brightness(0-100).
Increasing analog value increases green;
Decreasing analog value increases purple(0-100).
Increasing analog value increases color;
Decreasing analog value decreases color (0-100).
Increasing analog value increases definition;
Decreasing analog value decreases definition (0-100).
Increasing analog value increases black light;
Decreasing analog value decreases black light (0-100).
There are three Color Temperature modes,
"NORMAL , , " "WARM" "COOL ".
Page 16
Sound Adjustment
Select to enter the SOUND submenu. Press "Up/Down" key on the remote control or the key "CH+/CH-" on the front
panel to choose what you need. Press the "Left / Right" key on the remote control or the "VOL+/VOL-" key on the front
panel to adjust analog value or state (see below table).
Attention
1. Normally,the value of 50 is recommended;
2. The treble or bass analog value which is adjusted by the users
will be saved under the user-defined mode.
3. You can adjust bass and treble only in personal mode.
BASS
TREBLE
BALANCE
Remote Control Shortcut Keys
Smart Sound: SMART S
MUTE: MUTE
VOLUME: VOL+, VOL-
Press SMART S key on the remote control. You can switch the mode
SOUND SELECT:
among the "PERSONAL", "STANDARD","NEWS" and "MUSIC".
ItemFunctionDescription
SOUND MODE
BASS
TREBLE
Adjust audio effect mode
Adjust bass value
Adjust treble value
BALANCE Adjust balance of left or right sound
"PERSONAL","STANDARD","NEWS","MUSIC" four states.
Increasing analog value increases bass;
Decreasing analog value decreases bass (0-100).
Increasing analog value increases treble;
Decreasing analog value decreases treble (0-100).
Increasing analog value decreasing left volume;
Decreasing analog value decreases right volume(0-100).
PERSONALSOUND MODE
ADJUST:
EXIT:
MENU
50
50
26
14
Page 17
Advance Settings
Select to enter the ADVANCE submenu. Press "Up/Down"key
on the remote control or the key "CH+/CH-" on the front panel to
choose what you need. Press the "Left / Right"key on the remote
control or the " VOL+/VOL-" key on the front panel to adjust analog
value or state (see below table).
NR
BLUE SCREEN
SCALE
WEAK
OFF
NORMAL
15
ADVANCE SEL ECT: ADJUST:
Option Function Description
NR
BLUE SCREEN
SCALE
Adjust model of NR
Open or close BLUE SCREEN
Select picture scale of the picture.
"WEAK","MIDDLE","STRONG","OFF".
"ON/OFF", two states.
"FULL", "ZOOM", "ZOOM2", "NORMAL", "PANORAMA",
EXIT:
MENU
Page 18
System Settings
Select to enter the submenu. Press "Up/Down" key
SYSTEM
on the remote control or the key "CH+/CH-" on the front panel to
choose what you need. Press the "Left / Right"key on the remote
control or the " VOL+/VOL-" key on the front panel to adjust analog
value or state (see below table).
OSD LANG UAGE
H - POSITION
V - POSITION
DURATION
HALFTONE
SLEEP
RESET
SYSTEM SEL ECT: ADJUST:
Option Function Description
OSD LANGUAGE
H-POSITION
V-POSITION
DURATION
HALFTONE
SLEEP
RESET
Choose OSD menu display language
Adjust H-position of OSD menu
Adjust V-position of OSD menu
Adjust duration of OSD menu
Adjust halftone of whole picture
Set sleep time of the machine
Resume to setting of factory
There are many languages to select
Increasing analog value, OSD menu move toward right;
Decreasing analog value, OSD menu move toward left (0-100).
Increasing analog value, OSD menu move toward down;
Decreasing analog value, OSD menu move toward up(0-100).
Increasing analog value, extend duration time of OSD menu; (0-100).
Increasing analog value increases halftone;
Decreasing analog value decreases halftone(0-8).
Off,15,30, 45, 60,unite: minute.
Reset all values to setting of factory.
ENGLISH
OFF
EXIT:
50
50
100
MENU
8
16
Page 19
Page 20
Page 21
Page 22
Page 23
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.