ViewEra V171HT User Manual

17” TFT-LCD TV MONITOR
V171HT
USERS MANUAL
Rev. 1.0
www.viewera.com
1. Introduction
Product Description .................................. Page 1
Package Contents ..................................... Page 1
Product Features .................................. Page 2
Screen Cleaning Techniques .................... Page 2
Additional ................................................ Page 3
2. Control Functions …………………….. Page 5
3. Input Diagrams ....................................... Page 14
4. Installation............................................... Page 15
5. Product Specifications............................. Page 16
6. Dead Pixel Policy……............................. Page 18
7. Warranty and Customer Service ...... Page 18
8. Windows Setup ....................................... Page 19
9. Remote Control Function ...................... Page 20
10. Trouble Shooting
Page 21
1. Introduction
Product Description
Congratulations on your purchasing ViewEra LCD TV monitor. It
incorporates high quality display into a small light weighted module. It has power-saving capabilities and emits no radiation. You will certainly benefit from this monitor in lots of ways; to name some of them: comfort safety, and environmental protection.
This LCD monitor incorporates 17” color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance. Its maximum resolution of SXGA 1280 x 1024 is ideal for displaying complex graphics and high definition images. Its other outstanding capabilities include TV tuner with remote control, built-in speakers and OSD (On Screen Display) controls.
Package Contents
Included with your LCD monitor as following items
17 TFT LCD monitor 15 pin D-sub signal cable Audio Cable Power cord Power adapter Remote control Users manual
Page 1
Product Features
High contrast ratio TFT LCD display supports resolution up to SXGA
1280 × 1024. @75Hz.
Wall mountable with. Built-in speakers provide sound performance. Power management system conforms to VESA DPMS standard. Support Plug & Play, no need for driver installation. Advanced OSD controls for picture quality adjustment. Detachable stand for wall-mounting with VESA 75 (mm) bracket. Composite video and audio inputs, S-video input, TV tuner, line-out
jack for external speakers
Screen cleaning techniques
Gently clean the screen with a clean camel hair lens brush, or a soft,
clean, lint-free cloth, to remove dust and other particles that can scratch the screen.
Do not apply pressure to the screen surface when wiping it clean. Do not pour or spray any liquid directly onto the screen or casing.
Chemical cleaners have been reported to damage the screen or case of the LCD monitor.
Page 2
Additional
Read all of these instructions and save them for later use. Follow all warnings and instructions on the product. Product
Do not cover or block the venting holes in the case. Do not insert sharp objects or spill liquid into the LCD monitor through
cabinet slots. They may cause accident fire, electric shock or failure.
♦ Disconnect the power plug from the AC outlet if you will not use it for
an extended period of time.
♦ Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks.
♦ Do not touch the screen directly with your fingers. You may damage the
screen, and oil from your skin is difficult to remove.
♦ Do not apply pressure to screen. The LCD is very delicate.
Power
Use the type of power indicated on label.
Plugs
Do not remove any of the prongs of the monitor’s three-pronged power
plug.
Disconnect the power plug from the AC outlet under following
conditions
When the power cord or plug is damaged or frayed.  The product does not operate normally when the operating
instructions are followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician.
 If the product exhibits a distinct change in performance, service may
be required.
Page 3
Power and extension cords
♦ Do not allow anything to rest on the power cord.
Do not locate this product where persons will walk on the cord.
Use the proper power cord with correct attachment plug type. If the
power source is 120V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country’s safety regulations, such as VDE for Germany.
♦ Do not over load wall outlets or power cords. Ensure that the total of all
units plugged into the wall outlet does not exceed 10 amperes.
♦ Ensure that the total ampere ratings on all units plugged into the extension
cord is not above the cord’s rating.
♦ If the power supply cord, which came with your monitor, is to be
connected to the PC instead of the wall outlet, Use an UL/TUV approved computers with receptacle rated 100~240V AC, 50/60Hz, 1.0A(minimum) only.
Environment
Place the monitor on a flat and leveled surface. Place the monitor in a will-Ventilated place. Keep the monitor away from
Overly hot, cold or humid places, places directly under sunlight,
dusty surroundings, equipment that generate strong magnetic fields.
Please adjust the frequency to 75 Hz after setting up the LCD monitor.
Then push the OSD menu button and use the Auto Adjust function to find
the best mode of your computer.
Page 4
2. Control Functions
a.PC,Audio,DVI
Control Button Front View
﹝2﹞ ﹝5﹞ ﹝1﹞ ﹝3﹞ ﹝4﹞
1. Power Switch Turn on/ off the monitor.
2. Auto adjusting Press this button to obtain the best display
quality and adjust the image position.
3. Adjust (decrease ) This button is used to decrease the value of
selected control option.
4. Adjust (increase ) This button is used to increase the value of
selected control option.
5. OSD menu / select Press this button to show the OSD menu on
the screen. Select the OSD control options.
Page 5
OSD Controls
Monitor Function Selection Menu
AUTO ADJUST
BRIGHTNESS Adjust the brightness by using and buttons. CONTRAST Adjust the contrast by using and buttons.
CLOCK Adjust the clock by using and buttons. PHASE Adjust the phase by using and buttons.
H-POSITION Press to move the image to right;
V-POSITION Press to move the image upward ;
Select this function to obtain the best display quality and adjust the image position .
Press to move the image to left.
Press to move the image downward.
Page 6
Tools Menu
VOLUME Adjust the speaker volume by using and
buttons.
MUTE Speakers are mute.
RESET Recall the factory settings
Page 7
Color Temperature and RGB Adjusting Menu
COLOR
TEMP.
RED
GREEN BLUE Blue pixel brightness adjustment.
Color temperature selection --6500K, 7500K and
9300K.
Red pixel brightness adjustment.
Green pixel brightness adjustment.
Page 8
OSD Function Selection Menu EXIT OSD Exit the OSD menu.
OSD H.
POSITION
OSD V.
POSITION
OSD DURATION Set the OSD display timer. LANGUAGE Select the language for OSD.
Press to move the OSD to right ; Press to move the OSD menu to left. Press to move the OSD menu upward ; Press to move the OSD menu downward.
Page 9
b.AV,TV Control Button Front View
5 4 1 2 3
1. Power Switch Power switch and remote sensor
2. Decrease () Volume decrease, OSD menu selection downward and
channel down () in TV mode.
3. Increase () Volume increase, OSD menu selection upward and
channel up () in TV mode.
4. OSD menu / Select
Press this button to show the OSD menu on the screen . Select the OSD control options.
Monitor Function Selection Menu
BRIGHTNESS Adjust the brightness by using and buttons.
CONTRAST Adjust the contrast by using and buttons.
SATURATION Adjust the saturation by using and buttons. TINT Adjust the tint by using and buttons.
5. Source Selection Select the input signal ( PC/ AV/ S-Video/ TV).
Page 10
SHARPNESS Adjust the sharpness by using and buttons.
Page 11
Tools Menu
VOLUME Adjust the volume by using and buttons.
MUTE Speakers are mute. RESET Reset function.
INPUT Select input signal (PCAVS-VideoTV).
Page 12
** TV Mode only **
TV Function Selection Menu
CH SEARCHING TV channel auto searching CH EDIT Add or delete channel. CH FINE TUNE Tune up the signal for channel reception.
AIR-CABLE Select TV signal ,air or cable, by using
and buttons.
CH SYSTEM TV system selection.
Page 13
3. Input Diagrams
Inputs
【1】 【2】【3】【4】【5】 【6】 【7】
1. TV TUNER IN TV Tuner or cable signal input
2. DC IN DC power jack.
3. AV IN Composite video signal input.
4. S-VIDEO IN S-Video signal input.
5. LINE OUT Sound signal output (3 mm phone jack).
6. COMPOSITE AUDIO IN
7. VGA input Connect to PC VGA D-Sub signal.
Audio signalright and left channel.
Page 14
4. Installation
Electrical Connection
Please follow the instruction below to properly connect the LCD monitor
to external electrical source.
1. Connect the female-end of the power cable to the transformer. Connect the male-end of the power cable to the wall outlet or extension cable.
2. Connect the cable from the other end of the transformer to the LCD monitor DC IN located at the back of the LCD monitor.
Signal Connection
1. Power off both the LCD monitor and PC system before connecting them.
2. Take out the VGA cable from the box, then connect it to the signal connector at the back of the LCD monitor.
3. Connect the other end to the VGA connector on the back of the PC system.
4. Please make sure the connections to both the PC system unit and the LCD monitor are strong and secure. Please don’t forget to tighten the screws on each connector end.
5. Now turn on both the PC system unit and the LCD monitor.
6. After you finish setting up the LCD monitor, please set the refresh rate to 75Hz.
7. After setting up the LCD monitor, please perform Auto Adjust in OSD so that the LCD monitor will be automatically set to optimal color display each time.
* Please note: When you disconnect any power cable or signal cable, please do not pull the cable by grabbing the cable body. Please grab the cable connector itself whenever you try to pull the cable during disconnect.
Page 15
5. Product Specifications
Model Spec LCD Display 17” Active matrix TFT LCD panel Pixel Pitch 0.264(H) x 0.264(V) mm Max. Resolution 1280(H) x 1024(V), SXGA Contrast Ratio Typical: 500 : 1 (Min: 400:1) Brightness Typical : 300 cd/m2 (Min : 250) Response Time Typical: 12 ms (Max: 25) Display Color 16.7 M View Angle H/ V
Display Mode VGA, SVGA, XGA, SXGA Power consumption ON<48W (maximum) Frequency Horizontal: 31.5-80KHz; Vertical: 56-75Hz TV tuner NTSC, 125 channels Signal Connector D-sub 15, composite audio/video, OSD Menu Brightness, contrast, auto adjusting, clock, phase,
Power Adapter AC Input : 100-240V~1.8A, 50-60Hz
Operating Conditions Storage Conditions Certification BSMI,FCC (DOC), CE-B, TUV/GS, UL,CUL Set Size 413(W) x 414(H) x 195(D) mm Weight Net7.5Kgs , Gross9.8Kgs
Typical: 140°/ 130°
volume, color temperature and language.
DC Output : 12V/ 4.2A Temperature : 0~ 40 Humidity : 20% ~ 85% Temperature : -20~ 60 Humidity : 10%~95%
Page 16
V171HT
Display Modes
Mode Resolution H Freq (KHz) V Freq (Hz)
1 640 × 350 31.469 70.070 2 640 × 480 31.469 59.940 3 640 × 480 37.861 72.809 4 640 × 480 37.500 75.000 5 720 × 400 31.469 70.087 6 800 × 600 35.156 56.250 7 800 × 600 37.879 60.317 8 800 × 600 48.077 72.188
9 800 × 600 46.875 75.000 10 1024 × 768 48.363 60.004 11 1024 × 768 56.476 70.069 12 1024 × 768 60.023 75.029
13 1280 × 1024 63.981 60.020 14 1280 × 1024 79.760 75.025
Page 17
6. Dead Pixel Policy
Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra guarantees that the monitor will be replaced if the number of dead pixels on our monitor exceeds 5 pixels within the first year from the date of purchase.
7. Warranty and Customer Service
Warranty
ViewEra warrants the 15/17 TFT-LCD monitors for one year for parts
and labor from the date of purchase. For detail information, please refer to our website. (http:// www.viewera.com/warranty.htm)
Customer Service
Contact your ViewEra retailer or ViewEra for after sale service. You may contact ViewEra Customer Support:
1. By Mail: 328 Paseo Tesoro, Walnut, CA 91789
2. By Telephone: (909)595-3748
3. By Fax: (909)595-3526
4. By E-mail: support@viewera.com
The business hours are 9:00 am – 6:00 pm PST, Mon – Fri.
Page 18
8. Windows setup
For the best display quality, please set the monitor type in Windows.
Control Panel > Display > Settings > Advanced > List All
Modes
For optimal resolution, please select “1280 × 1024 @ 75Hz
Page 19
9. Remote Control Function
4
7
5
NO
1 Power 6 OSD Menu 2 Channel Adjustment 7 Number 3 Volume Adjustment 8 Source 4 Mute 9 Display 5 OSD Adjustment 10 CATV / AIR
FUNCTION NO
Page 20
1
3
2
FUNCTION
10. Trouble Shooting
1) Power on but no picture Make sure the VGA cable is tightly connected from the video output
connector on the video card to the video input connector on the monitor.
Make sure you are using the standard power adapter coming with the
monitor.
→ Check your video card if the driver is correctly installed. If there is no
video signal from the video card, “NO INPUT SIGNAL” will show on the screen.
2) Wrong or abnormal colors If any color (red, green, or blue) is missing, check video cable to make
sure it is securely connected. Loose pins in the cable connector can cause a bad connection.
3) The text and icon look blurry LCD monitor has a native resolution which pixels are produced by cells
in fixed positions. When a resolution different from the native resolution is chosen, the LCD monitor uses various interpolation methods to achieve the pseudo resolution. To achieve the optimum viewing quality, choose the native resolution of the panel is recommended.
→ Use “Auto Tuning” function to adjust image quality on the OSD menu or
you can hold button 2 for 3 seconds to do auto tuning.
4) Display position is incorrect
→ Use “Auto Tuning” function to adjust image position on the OSD menu
or you can hold button 2 for 3 seconds to do auto tuning.
5) Speakers have no sound
→ Make sure the audio cable is tightly connected from the audio output jack
on the PC to the audio input jack on the monitor.
Page 21
6) Residue image
→ If an image remains on the screen for an extended period of time, it may
be imprinted in the screen and leave a residue image. It is characteristic of liquid crystal and is not malfunction or deterioration of the liquid crystal. The residue image will disappear after a period of time. It is recommended to set up the screen saver for your LCD monitor.
7) Out of Rang The first thing you need to check is the screen resolution. Usually “Out of Range” is caused by improper resolution setting. You can recover the proper screen resolution as the following steps for Windows: (Assumed that the optimal resolution and frequency setting is 1280x1024@ 60Hz.)
Boot the computer into VGA Mode (F8) [repeatedly] at startup. Go to Control Panel”, double click on Display”, click on the SETTINGS TAB, and click on the ADVANCED button. Then Click on the Adapter TAB, click List All Modes” and change the screen resolution to 1280x1024. (You can select 16 bit or 32 bit color which depends on your video card capability.) Select 1280 by 1024, High Color (16 bit), Default Refresh Click on the OK” and APPLY”. After clicking the APPLY button, a message will be displayed “Your desktop has been reconfigured. Do you want to keep these settings? Click Yes” and OK”. Then click “OK” on the Display Properties window. Restart your PC After you restart, go back to “List All Modes” to adjust your screen refresh rate to 60 Hertz.
Page 22
The “Out of Range” may happen if you switch monitor A to monitor B for your PC. Whenever you change the monitor for your PC, your PC may detect it as a new hardware and automatically install a proper driver for the monitor. So, you will have both monitor A and monitor B drivers on your PC. Sometimes the two monitor drivers may conflict each other and cause Out of Range”. You can resolve “Out of Range” by uninstalling both monitor drivers and reboot your PC. The Windows will automatically detect the new hardware and install a proper driver for the monitor. Here is a quick way to uninstall the monitor drivers:
Right click on My Computer”, select Properties” and click on
Hardware”. Click on “Device Manager”, select “Monitor” and click on +” in front of “Monitor”. Then you can see one of the monitor drivers
called Plug and Play Monitor”. A quick way is to uninstall all the monitor drivers and then let Windows automatically detect the new hardware. (Right click on the monitor driver and select “Uninstall”). Restart your PC
Page 23
Loading...