Mobil Indoor Speedpass
Installation Guide
P/N: 55225
Revision A
Mobil Indoor Speedpass Installation Guide
September 11, 1998
®
VeriFone
, Inc.
4988 Great America Parkway
Santa Clara, CA 95054-1200
T e le ph one: 408 -49 6-0 444
http://www.verifone.com
Printed in the United States of America.
© 1998 by VeriFone, Inc. All ri ghts reserve d.
No part of this publication covered by the copyrights herein may be
reproduced or copied in any form or by any means — graphic,
electronic, or mechanical, including photocopying, taping, or
information storage and retrieval systems — without written permission
of the publisher.
The content of this document is subject to change without notice. The
information contained herein does not represent a commitment on the
part of VeriFone, Inc.
Publications are not stocked at the address given above. Requests for
VeriFone publications should be made to your VeriFone representative.
VeriFone is a registered trademark of VeriFone, Inc. Speedpass is a
trademark of Mobil Oil Corporation. All other products men tioned in
this manual are trademarks or registered trademarks of their respective
owners.
Mobil Indoor Speedpass Installation Guide
Revision History
Revision Date Comments
A September 11, 1998 Initial release of software
and documentation.
FCC Compliance
This equipment complies with the requirements in Part 15 of FCC
rules for a Class A computing device. Operation of this equipment
in a residential area may cause unacceptable interference for radio
and TV reception requiring the operator to take whatever steps
necessary to correct the interference.
Safety Instructions
■
Read all instructions contained in this guide be fore making
any equipment connections.
■
Save these instructions for later use.
■
Unplug the unit before servicing or cleaning. Do not use
liquid or aerosol cleaners. Use only a damp cloth for
cleaning.
■
Do not use any attachments not specifically recommended
by VeriFone as they may result in the risk of fire, electric
shock, or injury to persons.
■
Do not use the unit near water.
■
Do not place the unit on an unstable cart, stand, or table.
The unit may fall, causing serious personal injury and/or
damage to the equipment.
Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Equipment Power Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4. Specifications. . . . . . . . . . . . . . . . . . . . . . . . .9
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Service and Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Contents ◆
i
◆ Contents
ii
1
This document provides the information necessary to install your
Mobil Indoor Speedpass System.
mobilind.wmf 125%
Introduction
Mobil Indoor
Speedpass
Power Sup ply
The Mobil Indoor Speedpass System is a self-contained device,
when properly installed, becomes an integral part of the POS
equipment. It has the ability of reading a retail customer’s tag when
placed near an antenna mounted on the face of the equipment.
Soft Key Guard
Card Swipe Guard
Multicable
Introduction ◆
1
Information from the tag is processed and transferred to POS
equipment.
◆ Introduction
2
2
Carefully inspect the shipping carton and its contents for any
damage that may have occurred during shipment. If anything
appears damaged, immediately file a claim with the shipping
company or carrier and notify the Point of Sales equipment
manufacturer.
Warning: Never use damaged equipment. A shock or fire
Remove the following items from the shipping carton:
Remove any protective plastic wrapping from the components and
place them on a table or countertop.
Retain the shipping carton and any packing material in case it is
necessary to move components from one location to another or to
return the equipment for service.
Unpacking
hazard may exist if equipment is energized in a
damaged condit ion.
Mobil Indoor Speedpass Unit with attached Mulitcable
■
Power Supply
■
Soft Key Guard
■
Card Swipe Guard
■
Unpacking ◆
3
◆ Unpacking
4
3
Unpack equipment in accordance with instructions listed in Chapter
2.
Warning: To reduce the risk of fire, do not place this unit near
When selecting a location for your Mobil Indoor Speedpass
equipment, avoid areas having:
Installation
any heat producing source.
Direct sunlight or objects that produce heat.
■
Excessive dust.
■
Electrical “noise” or devices that cause excessive voltage
■
variations such as air con diti oners, f ans, or high fr equenc y
security systems.
Installation Procedures
Use the following procedures to install and power up the Mobil
Indoor Speedpass.
1. Place the unit close to the POS equipment.
2. Uncoil the Multicable and ensure that it does not kink or is not placed under heavy equipment.
3. Uncoil the Power Supply cable.
4. Mount the unit on a custom stand, if applicable.
Installation ◆
5
5. Locate the RS232 and RS485 cabling from the POS equipment.
6. Insert the RS232 cable connector into the Multicable jack labeled PORT 1.
7. Insert the RS485 cable connector into the Multicable jack labeled PORT 3.
Equipment Power Up
Before installing your Mobil Indoor Speedpass equ ipment, a
quality surge prote ctor should be purchased to prote ct the
equipment from voltage surges. Ideally, the Mobil Indoor
Speedpass equipment and the POS equipment should have its own
dedicated AC power outlet. The surge protector is plugg ed into the
AC power outlet first. The Mobil Indoor Speedpass Power Supply
should then be plugged into the surge protector.
Use the following procedures to power up the Mobil Indoor
Speedpass unit:
1. Insert the Power Cable connector into the Multicable jack labeled POWER.
Warning: When the Power Supply is plugged into the AC power
outlet, voltage is immediately available to the Mobil
◆ Installation
6
Indoor Speedpass. Avoid handli ng the e xposed p ower
cable connector.
Note: The AC power outlet should be easily accessible
should the user desire quick power disconnect.
2. Connect the Power Supply to the AC power outlet or appropriately configured power connector.
3. Verify that the display is activated.
Warning: To turn off your Mobil Indoor Speedpass, always
unplug the power supply from the AC power outlet
first. This eliminates the presence of voltage at the
Multicable power receptacle and the potential shock
hazard.
Installation ◆
7
◆ Installation
8
4
Specifications
Power Requirements
Input Voltage : 120VAC 60Hz 18 W
■
Output Voltage: 12VDC 1000mA
■
Operating Environment
Temperature: 0 to 40 degrees C (32 to 104 degrees F)
■
Humidity: 20% to 90%, noncondensing
■
Service and Repair
Do not, under any circumstances, attempt to repair, service, or
adjust your Mobil Indoor Speedpass equipment. If you have any
problems with your unit, contact the manufacturer of your POS
equipment.
Specifications ◆
9
Cleaning
Routine cleaning can be accomplished by removing dust or dirt
with a clean, damp cloth and mild soap or detergent. Use a cloth
dampened with alcohol for more stubborn stains.
Warning: Never use thinner, trichloroethylene, or ketone based
solvents to clean this equipment or cabling as they
may deteriorate plastic parts.
◆ Specifications
10
Loading...