DC TO AC POWER INVERTER
POWER : 300W
PI300M
PI30024
for input voltage 12V
for input voltage 24V
ATTENTION – OPGELET - ACHTUNG
OVERLOADING THIS DEVICE OR CONNECTING IT WITH AN IN DUCTIVE LOAD (e.g. refriger ator, fan,
drill) WILL DAMAGE IT AND AUTOMATICALLY VOID THE WARRANTY !!
HET TOESTEL ZAL WORDEN BESCHADIGD INDIEN U HET OVERBELAST OF ER EEN INDUCTIEVE
BELASTING (vb. koelkast, boormachine, ventilator) OP AANSLUIT. DE GARANTIE VERVALT DAN
AUTOMATISCH !!
LA SURCHARGE DE L’APPAREIL OU LA CONNEXION D’UNE CHARGE INDUCTIVE (p.ex. vent ilat eu r,
réfrigérateur, perceuse) ENDOMMAGERONT L’APPAREIL ET LA GARANTIE SERA INVALIDEE
AUTOMATIQUEMENT !!
DIE GARANTIE ERLISCHT UND DER SPANNUNGSWANDLER KANN BESCHÄDIGT WERDEN, WENN SIE
IHN ÜBERLASTEN ODER MIT EINER INDUKTIVEN LAST VERBINDEN (z.B. Kühlschrank, Lüfter,
Bohrmaschine).
User Manual
Gebruikershandleiding
Manuel d'utilisation
Bedienungsanleitung
1. DESCRIPTION
voltage
indicator
power
switch
AC output
socket
crocodile
clips
2. CONNECTIONS
Connect to lighter for appliances 0-150W or connect directly to battery (clips
included) for appliances of 150-300W . The length of the cable is ≤ 2m.
Please verify if you have chosen the right operating voltage for both input and output.
3. OPERATION
When connected to an appliance, remember to turn on the inverter before turning
on the appliance. If the buzzer sounds during operation, this indicates that the
battery voltage is very low and that the inverter will be disconnected in 5 minutes.
"Turn on"
secondly
"Turn on"
firstly
PI300M & PI30024 v2 GB 1
4. OUTPUT CAPACITY
The inverter will switch off automatically if the total wattage of the electrical
appliances exceeds the inverter's output capacity. This will also happen if the
temperature of the inverter exceeds 55°C due to prolonged use.
5. SPECIAL RECOMMENDATIONS
Unplug the AC inverter when not in use and when starting the vehicle's motor.
If the AC inverter makes a beeping sound : switch off your appliance, unplug the
inverter and restart your vehicle's engine. The beeping sound is simply the lowbattery warning which indicates that the voltage of your battery is getting low.
Your inverter will shut down automatically if you do not restart your engine and
continue the use of your inverter. This will leave your vehicle's battery at about
10.5VDC (21VDC for a 24V inverter), enabling you to start your engine and
resume operation of the inverter. It also eliminates the possi bil ity of being
stranded with a dead battery.
To avoid over-discharging the battery, it is advisable to let your engine run for 10
to 20 minutes after every 2-3 hours of using the AC inverter. This allows your
vehicle's battery to recharge.
Please remember to connect the "+" wire to the "+" terminal and the "-" wire to the
"-" terminal if you choose to use an adapter for a direct connecti on between the
AC inverter and the battery terminals. IF YOU CONNECT THE WIRES TO
INCORRECT TERMINALS, THE POLARITY WILL BE REVERSED AND THIS
WILL DAMAGE THE INVE RTER. REVERSED POLARITY WILL INSTANTLY
VOID YOUR INVERTER'S WARRANTY.
Please remember to disconnect the AC inverter before using the battery charger
to replenish you battery's voltage. Failure to disconnect the inverter prior to
connecting a charger may result in an input spike which will damage the inverter.
CONNECTING THE INVERTER'S INPUT TO A BATTERY CHARGER WILL
VOID THE WARRANTY AND MAY DAMAGE THE INV ERTER.
The battery's voltage must never exceed 15VDC (30VDC for a 24V inverter).
CONNECTING THE INVERTER TO A DC POW ER SOURCE GREATER THAN
15VDC (30VDC) WILL VOID THE WARRANTY AND MAY DAMAGE THE
INVERTER.
PI300M & PI30024 v2 GB 2
Loading...