Vectronics VEC-412KC Instruction Manual



VEC-412KC Assembly

Manual

To install your enclosure follow these instructions

Battery Charger/Conditioner

Rapid Battery Charger/Conditioner

in the VEC-412KC matching

(read all instructions before beginning ...

take your time):

1. Find the front panel decal and rear panel decal; separate using scissors. Put the rear panel decal on first. This is done by: a.) Remove all debris and oil from the chassis. This should

be done using a piece of cloth and alcohol. b.) Remove the crack and peel to expose the

adhesive. c.) Place the decal on the rear panel without securing it completely. d.) Gently

rub the alignment circles with your finger--if the circles are centered in the enclosure holes

(also check the corner alignment marks) secure the decal by rubbing and removing all air

bubbles.e.) If the alignment circles are not centered, adjust the decal accordingly then secure. f.) Use a penknife, or small Exacto

the adhesive side) g.)

Repeat for the front panel.

Next install the two L-brackets on the chassis using two of the 3/16" screws.

side of the L-bracket

edge of the enclosure. Refer to the diagram on the nest page for location and orientation.

3. Install the four 1/2" mounting screws next. Insert the screws, from the bottom, through die

four holes relativelv close to each corner of the chassis.

Place the four 3/16" round spacers on the mounting screws.

Now insert the PC board. This must be done by: a.) Insert the front of the PC board at an angle so the controls enter their respective holes. b.) Push the rear of the board in place.

Make sure the mounting screws align with the mounting holes in the PC board before

pushing.

Use the four hex nuts to secure the PC board. Be certain all appropriate components are centered with the enclosure holes before tightening.

7. Find switch caps.Align the red switch cap with SW2 and push it on. push on, rotate it 90° and try again. Repeat for SW3 and SW4 using the black switch caps.

S. Locate the strain relief bushing. Place the red/black wire into the strain relief and lock.

Insert the strain relief in the slot on the left rear of the enclosure. strap that holds the two parts of the strain relief together is inserted into the slot first.

9. Find the remaining decal and trim with scissors. Use the corner marks as guides. Put this decal on now by: a.) Remove all debris and oil from the top. b.) Orient the top so the front

is toward you. c.) Remove the crack and peel to expose the adhesive. d.) Place the decal on the top with the number I closest to the rear and use the switch hole as your guide. Do not secure it completely. e.) Gently rub the alignment circle with your finger--if the alignment circle is not centered adjust accordingly. g.) Use a penknife, or small ExactoTM knife, to cut out the switch hole.

10. Install the top now. First, insert the .343" black bushing into the switch hole on the top. Then, use the two remaining 3/16" screws for securing the top to the L-brackets.

the L-brackets are aligned properly.

11. Locate and put the knob on the rotating switch (SWI); you may need to loosen the set

screw.

You may adjust the distance between the bottom of the knob and the bushing by removing the knob and trimming the shaft of the switch with a pair of cutters. Once you are satisfied with the spacing, tighten the knob in place. Check the alignment of the decal by rotating the switch--if it is satisfactory secure the decal by rubbing and removing all air

bubbles. If the alignment is not adequate adjust and secure.

12. Finally, place the four rubber feet on the bottom of the enclosure at the corners.

and cut out the component holes

must be

connected to the chassis using the two holes centered on each

TMknife, to cut away the unused edges

(cut from the description side).

If it is difficult to

Make sure the connector

(cut from

The longer

Make sure



VEC-412KC Assembly

Manual

Rapid Battery Charger/Conditioner