Vaillant VRT 360f Operation Manual
For the owner and heating engineer
VRT 360f
Operating and Installation Manual
VRT 360f
Room temperature thermostat
GB
2
Contents
Operating and installation manual VRT 360f
Inhaltsverzeichnis
Notes on the documentation . . . . . . 4
Storage of the documents .................... 4
Symbols used ........................................... 4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating manual . . . . . . . . . . . . . . . . 6
1
Overview of the equipment . . . . . 6
2 Overview of the display . . . . . . . 7
3 Description of the appliance . . . 8
4 Operation . . . . . . . . . . . . . . . . . . . 8
4.1 Setting the operating modes ...... 9
4.2 Setting the current day and
time ................................................... 12
4.3 Setting timer programmes .......... 13
4.4 Setting the room temperature ... 16
4.5 Setting the hot water
temperature .................................... 18
4.6 Activating special functions ........ 19
4.7 Info level ........................................... 22
4.8 Changing the battery .................... 23
5 Manufacturer’s warranty and
liability . . . . . . . . . . . . . . . . . . . . 25
6 Recycling and disposal . . . . . . . . 25
3Operating and installation manual VRT 360f
Contents
GB
Installation instructions . . . . . . . . . . 27
7
Notes on the installation and
operation . . . . . . . . . . . . . . . . . . . 27
7.1 CE label ............................................. 27
7.2 Intended use .................................... 28
8 Safety instructions and regulati-
ons . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1 Safety instructions ........................ 29
8.2 Regulations ...................................... 30
9 Installation . . . . . . . . . . . . . . . . . 31
9.1 Place of installation ....................... 31
9.2 Fitting the receiver ........................ 31
9.3 Mounting the room temperature
thermostat ....................................... 33
10 Electrical installation . . . . . . . . . 35
10.1 Connecting the receiver ............... 35
11 Start-up . . . . . . . . . . . . . . . . . . . . 36
11.1 Installer level ................................... 37
11.2 Service/diagnostics level .............. 41
11.3 Handing over the appliance to
the owner ......................................... 43
12 Troubleshooting . . . . . . . . . . . . . 44
13 Technical data . . . . . . . . . . . . . . . 45
14 Vaillant Service . . . . . . . . . . . . . 46
4 Operating and installation manual VRT 360f
Notes on the documentation
The following information is intended to
help you throughout the entire
documentation.
Other documents apply in combination
with this installation and operation
manual.
We accept no liability for any damage
caused by failure to observe these
instructions.
Storage of the documents
Please pass on this operating and
installation manual to the owner of the
system in order for him/her to store it so
that it is available whenever it is required.
Symbols used
Please observe the safety instructions in
this manual for the installation of the
appliance.
Danger!
Immediate risk of serious injury
or death
Caution!
Potentially dangerous situation
for the product and environment.
Notes on the documentation
5GBOperating and installation manual VRT 360f
Note!
Useful information and
instructions.
• Symbol for a necessary task
Safety
The room temperature thermostat must
be installed by a suitably qualified
heating engineer, who is responsible for
adhering to the existing standards and
regulations.
We accept no liability for any damage
caused by failure to observe these
instructions.
Notes on the documentation, safety
6 Operating manual VRT 360f
Operating manual
1
Overview of the equipment
1
2
Abb. 1.1 Overview of equipment
Key
1 Display
2 Dial (turn and click)
I Info button
F Special functions button
P Programming key/installer level
1 Overview of the device
7GBOperating manual VRT 360f
2 Overview of the display
1
2
3
4
5
6
7
8
9
11
10
Fig. 2.1 Overview of the display
Key
1 Installer level and
Service/Diagnosis level (Chapter 11.1)
2 Info level (see 4.7)
3 Hot water symbol
4 Circulation pump symbol
5 Heating circuit symbol
6 Time/temperature display
7 Days of the week
8 Actual temperature
9 Operating modes (see 4.1)
10 Special functions (see 4.6)
11 Setting timer programmes (see 4.3)
Overview of the display 2
8 Operating manual VRT 360f
3 Description of the
appliance
The VRT 360f is a programmable room
temperature thermostat with weekly
programme for heating, hot water and
circulation pump for connection to
Vaillant heating equipment with eBus.
The connection between the room
temperature thermostat and the heating
unit is by radio link.
The VRT 360f enables you to specify the
room temperature using heating
programs. In addition, you can select
special functions such as the party
function, and control the timed
operation of a boiler and a circulation
pump.
4 Operation
The operating principle is based on the
three buttons and an dial (Vaillant "turn
and click“ operating concept).
The display normally shows the current
operating mode (e.g.
), or, if
activated, the special function and the
current room temperature, the day of
the week, the time and the symbol for
heating, hot water and/or the circulation
pump, depending on which is requested.
3 Device description, 4 Operation
9GBOperating manual VRT 360f
4.1 Setting the operating modes
T
able 4.1 provides you with an overview
of the operating modes you can select.
The selected operating mode affects the
timer programmes both for heating and
for hot water and the circulation pump.
• When the room temperature
thermostat is in normal display mode.
press the dial once – the symbol for
the selected mode flashes in the
display.
• Turn the dial until the desired
operating mode appears on the
display.
The display switches back to normal
mode after five seconds.
Operation 4
10 Operating manual VRT 360f
Symbol Meaning
Heating Hot water
Automatic:
The operation of the heating circuit changes between
the operation modes Heating and Energy Saving
. The heating circuit symbol is displayed if a heating
requirement is detected.
The operation of the hot water
storage cylinder/circulation
pump changes between
heating/ON and OFF
depending upon the time
programme set on the room
temperature thermostat.
The hot water symbol and the
circulation pump symbol are
displayed if the time window
is active.
Heating:
The heating circuit is operated according to the
room temperature, regardless of the programme set
on the room temperature thermostat. The heating
circuit symbol is displayed if a heating requirement is
detected.
Energy Saving:
The heating circuit is operated according to the
energy saving temperature "ECO“, regardless of the
programme set on the room temperature thermostat.
The heating circuit symbol is displayed if a heating
requirement is detected.
Table 4.1 Operating modes
4 Operation
11GBOperating manual VRT 360f
Symbol Meaning
Heating Hot water
Off:
The heating circuit is off, provided that
the frost protection function (if the room
temperature is below 5°C)
is not activated.
If the frost protection function is activated,
the heating circuit symbol is displayed.
The boiler is not heated up, regardless of
the set timer programme. The circulation
pump is switched off. The hot water
and circulation pump symbols are not
displayed.
Table 4.1 Operating modes (contd.)
Operation 4
12 Operating manual VRT 360f
4.2 Setting the current day and
time
To set the current time and day of the
week with the display in normal mode,
you must perform the following steps:
• Press the dial until a day of the week
starts flashing.
• Turn the dial until you see the current
day of the week.
MO = Monday
TU = Tuesday
WE = Wednesday
TH = Thursday
FR = Friday
SA = Saturday
SU = Sunday
• Press the dial. The hours start flashing.
• Turn the dial until you see the current
hour.
• Press the dial. The minutes start
flashing.
• Turn the dial until you see the current
minute.
The display switches back to normal
mode after five seconds.
If the calendar is activated on the
installer level (see 11.1), you can set the
day, month and year in the same way
after you set the time. This allows
automatic switching from winter to
summer time.
4 Operation
13GBOperating manual VRT 360f
4.3 Setting timer programmes
T
he room temperature thermostat is
equipped with a basic program (see table
4.2).
Time
window
Current day
/ Block of
days
Start
time
End
time
H1 M0 - FR 6:00 22:00
H2 — — —
H3 — — —
H1 SA 7:30 23:30
H2 — — —
H3 — — —
H1 SU 7:30 22:00
H2 — — —
H3 — — —
Table 4.2 Default heating, hot water and
circulation pump programmes
You can adapt the default programmes
to suit your needs. There are six steps to
setting the times you want.
1. Press the programming button P
2. Select the timer programme (heating,
hot water or circulation pump)
3. Select the time window
4. Select the current day or week block
5. Set the start time.
6. Set the end time.
Operation 4
14 Operating manual VRT 360f
You can define three time windows for
each day.
When you press the P button the display
returns to basic mode.
The table below illustrates the individual
steps again, using the example of the hot
water timer programme. If you want to
change the timer programme for heating
or the circulation pump, after pressing
the programming button P, select the
corresponding symbol (heating circuit or
circulation pump) and continue as shown
in the example.
Display Required steps
Press the programming
button P. The cursor (black
triangle) marks the value
which can be changed ( ),
which also flashes.
Turn the dial until the tap
symbol appears.
Press the dial. The cursor
marks the adjustable value
(H1), which also flashes.
Select the desired time
window by turning the dial.
Settings: H1, H2, H3
4 Operation
15GBOperating manual VRT 360f
Display Required steps
Press the dial. The cursor
marks the week block
display, which also flashes.
Select a block programme
or a single day of the week
by turning the dial.
Settings:
MO - SU
MO - FR
SA - SU
MO = Monday
TU = Tuesday
WE = Wednesday
TH = Thursday
FR = Friday
SA = Saturday
SU = Sunday
Display Required steps
Press the dial. The cursor
marks the start time and the
hour display flashes.
Select the start time by
turning the dial. Press
the dial again to set the
minutes.
Press the dial. The cursor
marks the end time and the
hour display flashes.
Select the end time by
turning the dial. Press
the dial again to set the
minutes.
Table 4.3 Setting time windows
Operation 4
Loading...