UVP PS-11 User Manual

Pen-Ray Power Supplies

PS-1, PS-2, PS-3, PS-4, PS-9 and PS-11

Operating Instructions

WARNING

Please read operating instructions before turning unit on.

INTRODUCTION

The Pen-Ray Power Supplies are made specifically for the Pen-Ray Lamps.
These power supplies provide proper voltage and current for starting and operat-

ing the lamps. Mating recommendations are available to provide optimum energy
output from and maximum life span of the Pen-Ray lamps.

DESIGN

Each power supply is designed to be maintenance free. There is an internal
circuit protection fuse which is designed to prevent mains circuit shut down in the
unlikely case of a catastrophic internal failure. The connector must be used with
the mating connector supplied with the Pen-Ray lamps. The connector is certified

to UL and CE compliance for use with this power supply. The power supply carries
the CE, ETL and ETLc marks.

WARNINGS

• Never handle the connector when the unit is in position as a hazardous shock
condition will exist.

• Do not attempt to operate lamps with operating voltages greater than 300 volts
continuously. Starting voltages do not apply.

• If the equipment is used in a manner not specified by UVP, LLC, the protection
provided by the equipment may be impaired.

Unit may become HOT during continuous use.

If internal circuit protection fuse blows, the unit should be returned to the factory for
service. The internal protection fuse is designed to trip if the primary coil short
circuits for any reason, protecting the user and the circuit it is plugged into. The unit
may be cleaned with any mild cleaning agent. Although the powder coated finish is
extremely durable, avoid acids and caustic substances. Do not use solvent cleaners
on plastic end caps.

ENVIRONMENT AL CONDITIONS

• For indoor use only

• Temperature: 5 to 40OC

• Maximum or Relative Humidity: 80% for temperatures up to 31OC decreasing
linearly to 50% relative humidity at 40OC

• Mains supply voltage fluctuations not to exceed +10% of the nominal voltage

• Installation is category II

• Pollution degree is 2

OPERATING INSTRUCTIONS

The operation of the PS series power supply is as follows:

1. Make sure the switch is in the off position.

2. Connect the Pen-Ray lamp to the connector making sure the connector is
completely inserted into its mating part.

3. Plug the unit into proper mains power supply.

4. Turn on the unit and the lamp should immediately light up.

5. Always unplug the unit when disconnecting or connecting the lamp.

MAINTENANCE

Keep the connector clean and free from debris, oil, fluids, etc. If the cord should
become frayed or cracked, it should be replaced immediately. Call UVP for
replacement service.

If connector arcing should occur due to dirt in the connector or attempting to
operate a Pen-Ray lamp which operates in excess of 300volts, do not continue
operation. The unit should be returned to the factory for repair. (Cleaning the
carbonized area between the connector pins may restore function to the power
supply).

SPECIFICA TIONS

Primary
Model Primary Current Starting Max. Lamp Lamp
No. Voltage AMPS Voltage Voltage Current Dimensions

PS-1 115Vac/60Hz 0.40 2300Vac 300Vac 18mA 6.3x3.7x2.3"
PS-1 230Vac/50Hz 0.21 2300Vac 300Vac 18mA (160x94x53mm)

PS-2 115Vac/60Hz 0.40 2000Vac 300Vac 6mA 6.3x3.7x2.3"
PS-2 230Vac/50Hz 0.21 2000Vac 300Vac 6mA (160x94x53mm)

PS-3 115Vac/60Hz 0.40 2100Vac 300Vac 10mA 6.3x3.7x2.3"
PS-3 230Vac/50Hz 0.21 2100Vac 300Vac 10mA (160x94x53mm)

PS-4 115Vac/60Hz 1.00 2800Vac 300Vac 26mA 4.6 x 5.8 x 3.8”
PS-4 230Vac/50Hz 0.55 2800Vac 300Vac 26mA (117x147x97mm)

PS-9 115Vac/60Hz 0.90 2400Vac 300Vac 48mA 5.8 x 4.6 x 3.6”
PS-9 230Vac/50Hz 0.50 2400Vac 300Vac 48mA (147x117x92mm)

PS-11 115Vac/60Hz 0.40 2300Vac 300Vac 18mA 5.2x2.2x3.5"
PS-11 230Vac/50Hz 0.21 2300Vac 300Vac 18mA (132x56x89mm)

NOTE: 115V ETL LISTED US/CANADA; 230V CE COMPLIANCE

81-0154-01 Rev F

Web Site: www.uvp.com

UVP, LLC 2066 W. 11th Street, Upland, CA 91786 • Tel: [phone] or [phone]

Ultra-Violet Products Ltd, Unit 1, Trinity Hall Farm Estate, Nuffield Road,

Cambridge, CB4 1TG UK • Tel: [phone]

Cambridge, CB4 1TG UK • Tel: [phone]

Web Site: www.uvp.com

81-0154-01 Rev F

Primary

Ultra-Violet Products Ltd, Unit 1, Trinity Hall Farm Estate, Nuffield Road,

UVP, LLC 2066 W. 11th Street, Upland, CA 91786 • Tel: [phone] or [phone]

NOTE: 115V ETL LISTED US/CANADA; 230V CE COMPLIANCE

PS-11 230Vac/50Hz 0.21 2300Vac 300Vac 18mA (132x56x89mm)
PS-11 115Vac/60Hz 0.40 2300Vac 300Vac 18mA 5.2x2.2x3.5"

PS-9 230Vac/50Hz 0.50 2400Vac 300Vac 48mA (147x117x92mm)
PS-9 115Vac/60Hz 0.90 2400Vac 300Vac 48mA 5.8 x 4.6 x 3.6”

PS-4 230Vac/50Hz 0.55 2800Vac 300Vac 26mA (117x147x97mm)
PS-4 115Vac/60Hz 1.00 2800Vac 300Vac 26mA 4.6 x 5.8 x 3.8”

PS-3 230Vac/50Hz 0.21 2100Vac 300Vac 10mA (160x94x53mm)
PS-3 115Vac/60Hz 0.40 2100Vac 300Vac 10mA 6.3x3.7x2.3"

PS-2 230Vac/50Hz 0.21 2000Vac 300Vac 6mA (160x94x53mm)
PS-2 115Vac/60Hz 0.40 2000Vac 300Vac 6mA 6.3x3.7x2.3"

PS-1 230Vac/50Hz 0.21 2300Vac 300Vac 18mA (160x94x53mm)
PS-1 115Vac/60Hz 0.40 2300Vac 300Vac 18mA 6.3x3.7x2.3"

No. Voltage AMPS Voltage Voltage Current Dimensions
Model Primary Current Starting Max. Lamp Lamp

SPECIFICA TIONS

supply).
carbonized area between the connector pins may restore function to the power
operation. The unit should be returned to the factory for repair. (Cleaning the
operate a Pen-Ray lamp which operates in excess of 300volts, do not continue
If connector arcing should occur due to dirt in the connector or attempting to

replacement service.
become frayed or cracked, it should be replaced immediately. Call UVP for
Keep the connector clean and free from debris, oil, fluids, etc. If the cord should

MAINTENANCE

5. Always unplug the unit when disconnecting or connecting the lamp.

4. Turn on the unit and the lamp should immediately light up.

3. Plug the unit into proper mains power supply.

completely inserted into its mating part.

2. Connect the Pen-Ray lamp to the connector making sure the connector is

1. Make sure the switch is in the off position.
The operation of the PS series power supply is as follows:

OPERATING INSTRUCTIONS

C decreasing

O

• Pollution degree is 2

• Installation is category II

• Mains supply voltage fluctuations not to exceed +10% of the nominal voltage

C

O

C

O

linearly to 50% relative humidity at 40

• Maximum or Relative Humidity: 80% for temperatures up to 31

• Temperature: 5 to 40

• For indoor use only

ENVIRONMENT AL CONDITIONS

on plastic end caps.
extremely durable, avoid acids and caustic substances. Do not use solvent cleaners
may be cleaned with any mild cleaning agent. Although the powder coated finish is
circuits for any reason, protecting the user and the circuit it is plugged into. The unit
service. The internal protection fuse is designed to trip if the primary coil short
If internal circuit protection fuse blows, the unit should be returned to the factory for

Please read operating instructions before turning unit on.

the CE, ETL and ETLc marks.
to UL and CE compliance for use with this power supply. The power supply carries

the mating connector supplied with the Pen-Ray lamps. The connector is certified
unlikely case of a catastrophic internal failure. The connector must be used with
circuit protection fuse which is designed to prevent mains circuit shut down in the
Each power supply is designed to be maintenance free. There is an internal

DESIGN

output from and maximum life span of the Pen-Ray lamps.
ing the lamps. Mating recommendations are available to provide optimum energy
These power supplies provide proper voltage and current for starting and operat­The Pen-Ray Power Supplies are made specifically for the Pen-Ray Lamps.

INTRODUCTION

WARNING

Unit may become HOT during continuous use.

provided by the equipment may be impaired.

• If the equipment is used in a manner not specified by UVP, LLC, the protection

continuously. Starting voltages do not apply.

• Do not attempt to operate lamps with operating voltages greater than 300 volts

condition will exist.

• Never handle the connector when the unit is in position as a hazardous shock

WARNINGS

Operating Instructions

PS-1, PS-2, PS-3, PS-4, PS-9 and PS-11

Pen-Ray Power Supplies