Universal Remote Control (URS) UR3-SR3 User Manual
Universal Remote Control, Inc.
www.universalremote.com
UR3-SR3
Operating Manual
For Easy Clicker
1
This remote control is designed to operate most Digital
and Analog Cable Boxes, as well as TVs, and a DVD
player.
Introduction
Install two
AAA alkaline batteries
as shown here
1
Before you program or operate the remote control, you
must install two new AAA alkaline batteries.
STEP1 Remove the battery compartment cover from the
back of your remote control.
STEP2 Check battery polarity carefully, and install the
batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
Replacing Batteries
2
2
Button Functions
3
Programming the Remote Control.
4
A. Quick Set-Up Method
A. Quick Set-Up Method
STEP1
Turn on the component you want to program. To
program your TV, turn on the TV.
STEP2
Press and hold the [DEVICE] key for 5 seconds until
the Device LED will blink once and stays on.
Continue to hold the [DEVICE] key and press the
*Note : In this section, when you are instructed to press a
[DEVICE] button, that means you should press either
the CBL, TV, or DVD button, depending on which
device you are programming the remote to operate.
3
number key assigned to your brand in the Quick
Set-up Code Table and release both [DEVICE] key
and the number key to save the code. The Device
LED will blink twice to confirm that the code is
stored.
STEP3
Point the remote control at the component.
STEP4
Press the [DEVICE] button. If it turns off, it is
programmed for your component. If it does not turn
off, use the Pre-Programmed 3-Digit code Method
or Scanning Method.
Repeat the steps above for all components (CBL, TV, DVD).
B. Quick Set-up Code Tables
B. Quick Set-up Code Tables
Quick Number
Manufacturer/Brand
CBL
0 PACE DTA
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL
3 MOTOROLA DTA
4 EVOLUTION DTA
5 CISCO IPTV
6 ADB IPTV
7 TECHNICOLOR
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV
0 SANYO
1 SONY
2 SAMSUNG
3LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8SHARP
9 VIZIO
Quick Number
Manufacturer/Brand
TV
4
C. Manual Programming
C. Manual Programming
The remote control can be programmed by entering a threedigit code number that corresponds to particular brands and
models of equipment. The three-digit code numbers are listed
in the code tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the remote
control to operate Cable Box, TV and DVD.
STEP2 Press the [DEVICE] button and the [OK/SEL]
button simultaneously for three seconds. The
corresponding device LED will turn on indicating
that it is ready to be programmed. The LED will
remain on for 20 seconds. The next step must be
entered while the LED is on.
STEP3 Point the remote control toward the equipment
and enter the three-digit code number assigned
to your brand from the code tables. If there are
more than one three-digit number listed for your
brand, try one code number at a time until your
equipment turns off.
*Note : You can verify that you have selected the correct
code by pressing the [MUTE] button. The
equipment should turn on or off.
STEP4 Store the three-digit code by pressing the same
[DEVICE] button once again. The device LED will
DVD
0 HITACHI
1 SONY
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX
5 PANASONIC
6LG
7JVC
8 DENON
9 PIONEER
Quick Number
Manufacturer/Brand
5
blink twice to confirm that the code has been
stored.
*Note : Try all the functions on the remote control. If any
of the functions do not operate as they should,
repeat the instructions from Step 2 using the next
three-digit code number from the same brand list.
D. Auto Search Method
D. Auto Search Method
If none of the three digit code numbers assigned to your
brand of equipment works, or the code table does not list your
brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by
following steps:
STEP1 Turn on the equipment that you want the remote
control to operate (Cable Box, TV, or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL]
button simultaneously for three seconds. The
device LED will turn on indicating that it is ready
to be programmed. The LED will remain on for 20
seconds. The next step must be entered while
the LED is on.
STEP3
Press the [CH5] or [CH6] button one at a time or
keep it pressed. The remote will emit a series of
Power ON/OFF code signals. Release the [CH5] or
[CH6] button as soon as the equipment turns off.
*Note : You can verify that you selected the correct code
by pressing the [MUTE] button. The equipment
should turn On or Off.
STEP4 Press the same [DEVICE] button to store the
code. The Device LED will blink twice to confirm
that the code has been stored.
E.
E.
To find the Three-Digit Code that Was
To find the Three-Digit Code that Was
Programmed using the Auto Search
Programmed using the Auto Search
Method
Method
STEP1 Press the appropriate [DEVICE] button and the
[OK/SEL] button simultaneously for three
seconds. The device LED will turn on for 20
seconds. The next step must be performed while
the LED is on.
6
STEP2 Press the [INFO] button. The device LED will blink
a number of times indicating the number of each
digit for the code. Each digit is separated by a
one second interval of the LED being off.
Example : One blink, then three blinks, then eight blinks
indicates the code number 138.
*Note : Ten blinks indicates the number 0.
F.
F.
Programming a Second TV to the DVD Button
Programming a Second TV to the DVD Button
STEP1 Press the [DVD] button and the [OK/SEL] button
simultaneously for 3 seconds. The DVD LED will
turn on for 20 seconds. The next step must be
performed while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the
three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD]
button. The device LED will blink twice to confirm
that the code has been stored.
G. Programming for Advanced Functions.
G. Programming for Advanced Functions.
In the CABLE device mode, the A,B,C,D and blank macro
buttons can be programmed to act as a 'Macro' or
Favorite Channel button. This allows you to program up to
five 2-digit channels, four 3-digit channels or three 4-digit
channels that can be accessed with ONE button press.
*Note : The A,B,C and D buttons are not programmable if
you have a Digital Cable Box made by Pace,
Pioneer or Scientific-Atlanta.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button
will turn on for 20 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel you
want programmed first (for example, 007) using the
Number Pad, then press the [STOP] button. Then
enter the code for the next channel (for example,