Universal Remote Control (URS) MRX-4IR User Manual

Owner’s Manual

MRX-4IR

Network Base Station

MRX-4IR Network Base Station Owners Manual ©2012 - 2014 Universal
Remote Control, Inc.

The information in this Owner’s Manual is copyright protected. No part of
this manual may be copied or reproduced in any form without prior
written consent from Universal Remote Control, Inc.

UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR
OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE
IN THIS MANUAL.

The information in this Owner’s Manual may be subject to change
without prior notice.

Total Control is a registered trademark of Universal Remote Control, Inc.

URC - Control the Experience is a registered trademark of Universal
Remote Control, Inc.

All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.

500 Mamaroneck Avenue, Harrison, NY 10528

Phone: [phone] Fax: [phone]

TABLE OF CONTENTS

Introduction 1

Features and Benefits 1

Parts Guide 1

Front, Rear and Bottom Panel Descriptions 2

Network Installation 5

Network Discovery & Download 6

Optimizing IR Flasher Levels 7

Overview of IR Routing 8

Limited Warranty Statement 9

End User Agreement 11

Specifications 12

Federal Communication Commission
Interference Statement 13

Regulatory Information to the user 14

Declaration of Conformity 15

MRX-4IR NETWORK BASE STATION

Introduction

Thank you for purchasing the MRX-4IR Network Base Station. The
MRX-4IR requires a Total Control MRX Advanced System Controller
and compatible interfaces, programmed by a Custom Professional,
to control your home. Communicating over the network using Wi­Fi, or a wired LAN connection, the MRX-4IR receives commands
from the System Controller and relays them, via IR, to four or more
devices. Controlling your home is simple with the MRX-4IR.

Features and Benefits

=

IR Flasher Outputs

Control up to four of your components without ever getting up
from your seat.

=

Front IR Blaster

Control IR devices where an IR emitter cannot reach the
device’s location, like a TV over a fireplace.

=

Network Connectivity

Receives commands over the network from an MRX Advanced
System Controller and then sends IR signals to control your

components.

=

Compact Size

The small size of the MRX-4IR allows it to easily fit behind
devices or into places where a traditional base station would not.

Parts Guide

The MRX-4IR includes:

1 - MRX-4IR
1 - AC Power Adapter
4 - Mounting Screws

1 - Mounting Plate
4 - IR Emitters (3.5mm plugs)
1 - Owner’s Manual

Page 1

MRX-4IR NETWORK BASE STATION

Front, Rear and Bottom Panel Descriptions

Front Panel

The front panel consists of 3 indicator lights and an IR Blaster.

IR Blaster

Power LED: The Power LED illuminates when the unit is powered.

Status LED: When the MRX-4IR powers up, both the Status and

Data LEDs blink. When a network connection is made, the Status
LED color will vary depending upon its “connected state”: good
signal strength is represented by “Green”, poor signal strength by
“Orange” (which is only present when a wireless connection is
used) and no connection is OFF.

Data LED: The Data LED flashes as the MRX-4IR transmits IR data.

IR Blaster: The front IR Blaster sends IR signals to one or more

components placed in direct line of sight.

Page 2

MRX-4IR NETWORK BASE STATION

Rear Panel

The rear panel ports are:

DC 12V Power: Plug in the included 12V DC 1A power supply.

IR Outputs: Connect an included 3.5mm IR emitter to each of the

four IR outputs. Adjust the IR output signal strength for port 1 using
the attenuator located on the bottom of the unit.

LAN Connection: If a wired connection is needed, this port uses a
standard Ethernet (RJ-45) plug to communicate via the local area
network.

Page 3