Uniden Um50 User Instruction Manual
USER INSTRUCTION MANUAL
GETTING TO KNOW THE UNIDEN UM50:
The Uniden UM50 will increase your cellular signal, expand your service coverage
area, enhance voice call quality and signicantly increase data speeds.
The Uniden UM50 is equipped with internal automatic oscillation protection.
The booster constantly monitors the environment in which it is operating and
automatically adjusts the gain/power accordingly to protect itself while giving you
a maximum coverage footprint. It is easy and simple to install and you can be up
and running in minutes.
TECHNICAL SUPPORT
CONTACT INFORMATION
Live Help: unidencellular.ca
Email: support@unidencellular.ca
Toll Free: 1-800-239-0394
2 year warranty against manufacturing defects.
Does not include misuse or customer damage.
Original Bill of Sale is required for all warranty claims.
The trademark is owned by America Corporation and its afliates is used under license by Signi Mobile.
12V Power Supply
Your Kit Includes:
Booster
Interior (distribution)
Antenna
Outdoor (signal)
Antenna
Optional In-Building Accessories:
Interior (distribution)
Antenna
Panel or Whip
Outdoor (signal) Antenna
Post or Yagi
Cable
30 ft Coaxial Cable
Power Supply
110V Power Adapter
TYPICAL VEHICLE INSTALLATION
1
3
4
2
Outdoor Antenna
Distribution Antenna
Booster
DC Power Connection
1
2
3
4
INITIAL SETUP INSTALLATION & ASSEMBLY:
During this process you will connect the outdoor signal antenna, interior distribution
antenna and the 12V power supply to the Uniden UM50 booster unit as follows:
OUTDOOR SIGNAL ANTENNA
Please connect the magnetic base unit to the outdoor antenna and place it on the
metal roof of the vehicle. Try to keep it as far away from the interior antenna as
possible. Once you have found the desired positioning for your outdoor antenna,
connect it directly to the booster on the connection marked “Outdoor”
INTERIOR DISTRIBUTION ANTENNA
Identify an appropriate location for the interior antenna and keep it as far away
as possible from the location of the outside antenna. Once you have found the
desired position for your indoor antenna, connect it directly to the booster on the
connection marked “Indoor”
BOOSTER PLACEMENT
You should place the booster in an easily accessible location within your vehicle
i.e. Under the passenger seating, in the rear of the vehicle or any other location
that keeps the booster hidden out of sight. Please DO NOT keep the booster in a
location that is continuously exposed to sunlight as it can overheat.
COMMISSIONING THE SYSTEM
Plugging in the power will switch the Uniden UM50 ON causing the “Power”
LED light on the backside of the unit to remain lit indicating the unit is properly
powered.
1
2
3
4
Explanation of LED Light Indicators located on the rear of the unit
The intelligent Automatic Gain Controls (AGC) in the Uniden UM50 enables it to reduce
the gain of the booster automatically and store these settings in the devices memory
unit. The UM50 will then continue to automatically scan the frequency and self adjust
accordingly every 5 seconds.
On the backside of the unit, there are three LED lights labeled: ”High” alarm, “Power”
and “Low” alarm. When the unit is plugged in, the LED “Power” light should be a solid
green color.
Orange LED alarm lights indicate the booster is automatically adjusting the gain. In
which case, the booster is functional.
Red LED alarm lights indicate oscillation (feedback) is severe and additional
distance between the indoor and outdoor antenna is required. If the LED light
continuously stays red, the UM50’s Automatic Gain Control will attenuate the signal
strength in order to stop the booster from oscillating.
Green LED alarm lights indicate the booster is functioning properly.
* Three solid green lights indicate the booster is functioning properly.
The trademark is owned by America Corporation and its afliates is used under license by Signi Mobile.
SMA Female Connector (50 ohm) LED Gain Control Alarm Indicator
LED Power IndicatorPower Input 12v
Loading...