U-Line U-ADA15IMB-00B Installation Manual

®

INSTALL GUIDE

1/4” Door & Drawer Panel Insert

Installation Guide

The Built-In Undercounter Leader Since 1962

U-LINE.COM

1 Insert Panel Installation

IMPORTANTIMPORTANT

CAUTION

IMPORTANTIMPORTANT

Custom 1/4'' Thick Door/ Drawer Panel
Insert

Drawer Models

1b. Drawer model inserts can be installed without removing the

drawer from the unit. Simply pull the drawer open and follow
instructions.

Insert Panel Preparation

A custom insert panel may be inserted into the doorframe.
Custom insert panels can be flat or raised, as long as the maximum
panel thickness, where inserted into the door / drawer reveal
(channel), is no more than 1/4" thick. For raised panels, the depth
of the reveal is 1/4" on all four sides.

Raised panels will reduce the door’s 90° swing/zero
clearance if the unit is installed next to a wall or similar
type of structure.

Panel Dimensions.

The insert panel must not weigh more than 20 lbs.

Model Width Height

1115R 13 15/16” 26 15/16”

1175R 22 15/16” 26 15/16”

2115R 14 1/32” 27 11/16”

2175R(F) 23 1/32” 27 11/16”

2275DWR 23 1/32” 12 15/32”

29R 19 13/16” 21 13/32”

75F 22 15/16” 26 15/16”

ADA15IM 13 15/16” 26 15/16”

ADA24R 22 15/16” 26 15/16”

BI2115 14 1-32” 27 11/16”

BI95 12 15/16” 13 15/32”

BI95BTP 12 15/16” 13 15/32”

BI98 13 15/16” 15 15/16”

CLR2160 14 1/32” 27 11/16”

CLRCO2175 23 1/32” 27 11/16”

CO1175 22 15/16” 26 15/16

CO2175F 23 1/32” 27 11/16”

CO29(F) 19 13/16” 21 13/32”

Insert Panel Installation

Door Models

1a. Remove top hinge screw pin with

Phillips head screwdriver. Remove
door by tilting forward and lifting
off bottom hinge pin.

2. Pull door / drawer gasket out of
groove (top edge of door /
drawer only). Start in the middle
and pull outward, moving toward
the edge . This may take some
force.

3. Remove the two outside screws
holding door / drawer handle.
Slightly separate door handle
from door.

4. Pull handle up and off.

Use care when handling the insert. Insert edges may be
sharp.

5. Slide custom door panel insert into 1/4-inch channel in door /
drawer front.

Use care not to damage magnet, located on door bottom,
when installing door insert. Do not set door on bottom
edge when pushing insert into place.

6. Holding door / drawer gasket out of the way, replace handle on
door, making sure it is seated properly on insert and that screw
holes line up.

7. Install two small screws removed in

8. Starting at the corners and working inward, push door gasket
into place on door.

Door Models Only

9. Place door on bottom hinge pin and install upper hinge screw.

Step 3

.

U-Line Insert Panel Installation 1

®

INSTALLATION GUIDE

SERVICE INFORMATION

If you have a problem with this appliance, your use and care guide has troubleshooting information to help you
quickly identify common problems and provide information on possible cause and remedy. Answers to
Customers Frequently Asked Questions are available at www.u-line.com/customer/faq.cfm. You may contact
U-Line directly:

GENERAL INQUIRIES:

U-Line Corporation

P.O. Box 245040

Milwaukee, Wisconsin 53224-9540 U.S.A.

Phone [phone]

FAX [phone]

Email: [e-mail]

www.u-line.com

SERVICE ASSISTANCE:

Phone [phone]

FAX [phone]

Email: [e-mail]

www.u-lineservice.com

PARTS ASSISTANCE:

E-mail: [e-mail]

ABOUT U-LINE

Building on 45 years, U-Line has captivated those with an appreciation for the finer things with exceptional
design, inspired innovations and attention to even the smallest details.

U-Line is synonymous with premium built-in undercounter ice making, refrigeration and wine storage appli­ances, the U-Line Corporation is committed to luxury under the counter. U-Line is known and respected for
unwavering dedication to product innovation, quality and selection. A bold and broad line of models is the prod­uct of visionaries in the pursuit of distinctive living environments in the kitchen and spaces beyond.

In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was
the first to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and
determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evi­dent today. The Milwaukee, Wisconsin based family operated business provides continuity and vision from
which innovations continue to be born.

Going forward, U-Line will continue offering best-in-class products that build on the company's numerous pat­ents and world firsts to guide the undercounter industry in realizing its unlimited potential.

The Built-In Undercounter Leader Since 1962

U-LINE.COM

©2009 U-Line Corporation

Publication Number 30304 10/2010 Rev. C