U-line U1224WCS13B User Manual

Download

USER GUIDE & SERVICE MANUAL

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

RIGHT PRODUCT. RIGHT PLACE. RIGHT TEMPERATURE. SINCE 1962.

1000 Series • 1224WC • 24" Single Zone Wine Captain® Model

USER GUIDE

u-line.com

Contents

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Intro

Safety

Safety and Warning Disposal and Recycling

Installation

Environmental Requirements Electrical Cutout Dimensions Product Dimensions Side by Side Installation Anti-Tip Bracket General Installation Integrated Panel Dimensions Integrated Panel Installation

Maintenance

Cleaning Cleaning Condenser Wine Rack Installation Extended Non-Use

Service

Troubleshooting Warranty

Service Extended

Wire Diagram Product Liability Warranty Claims Parts Ordering Replacement Parts

Grille / Plinth Installation Door Swing Door Stop Door Adjust Wood Trim Finishing Free Standing Kit

Operating Instructions

First Use Control Operation Sabbath Mode Airflow and Product Loading U-Line Wine Guide Recommended Wine Storage

System Diagnosis Guide Compressor Specifications Troubleshooting Extended Control Quick Guide Thermistor Defrost

USER GUIDE

u-line.com

WELCOME TO U-LINE

Congratulations on your U-Line purchase. Your product comes from a company with over five decades of premium modular

ice making, refrigeration, and wine preservation experience. U-Line continues to be the American leader, delivering versatility

and flexibility for multiple applications including residential, light commercial, outdoor and marine use. U-Line’s complete

product collection includes Wine Captain

Door Refrigerators, Drawer Models, Freezers, Combo® Models, and more.

U-Line has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired innovations

and attention to even the smallest details. We are known and respected for our unwavering dedication to product design,

quality and selection. U-Line is headquartered in Milwaukee, Wisconsin and has shipped product to five continents for over

two decades and is proud to have the opportunity to ship to you.

PRODUCT INFORMATION

Looking for additional information on your product? User Guides, Spec Sheets, CAD Drawings, Compliance Documentation,

and Product Warranty information are all available for reference and download at u-line.com.

Models, Beverage Centers, Clear Ice Machines, Crescent Ice Makers, Glass & Solid

PROPERTY DAMAGE / INJURY CONCERNS

In the unlikely event property damage or personal injury is suspected related to a U-Line product, please take the following

steps:

1. U-Line Customer Care must be contacted immediately at +1.800.779.2547.

2. Service or repairs performed on the unit without prior written approval from U-Line is not permitted. If the unit has been

altered or repaired in the field without prior written approval from U-Line, claims will not be eligible.

GENERAL INQUIRIES

U-Line Corporation

8900 N. 55th Street

Milwaukee, Wisconsin 53223 USA

Monday - Friday 8:00 am to 4:30 pm CST

T: +1.414.354.0300

F: +1.414.354.7905

Email: sales@u-line.com

u-line.com

SERVICE & PARTS ASSISTANCE

Monday - Friday 8:00 am to 4:30 pm CST

T: +1.800.779.2547

F: +1.414.354.5696

Service Email: onlineservice@u-line.com

Parts Email: onlineparts@u-line.com

CONNECT WITH US

Designed, engineered and assembled in WI, USA

Introduction 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Safety and Warning

Please read all instructions before installing, operating, or servicing the appliance.

Use this appliance for its intended purpose only and follow these general precautions with those listed throughout this guide:

SAFETY ALERT DEFINITIONS

Throughout this guide are safety items labeled with a Danger, Warning or Caution based on the risk type:

DANGER

Danger means that failure to follow this safety statement will result in severe personal injury or death.

DANGER

This unit contains R600a (Isobutane) which is a flammable hydrocarbon. It is safe for regular use. Do not use sharp objects to expedite defrosting. Do not service without consulting the “R600a specifications” section included in the User Guide. Do not damage the refrigerant circuit.

WARNING

Service must be done by factory authorized service personnel. Any parts shall be replaced with like components. Failure to comply could increase the risk of possible ignition due to incorrect parts or improper service.

WARNING

Warning means that failure to follow this safety statement could result in serious personal injury or death.

CAUTION

Caution means that failure to follow this safety statement may result in minor or moderate personal injury, property or equipment damage.

Safety and Warning 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Disposal and Recycling

DANGER

RISK OF CHILD ENTRAPMENT. Before you throw

away your old refrigerator or freezer, take off

the doors and leave shelves in place so children

may not easily climb inside.

If the unit is being removed from service for disposal,

check and obey all federal, state and local regulations

regarding the disposal and recycling of refrigeration

appliances, and follow these steps completely:

1. Remove all consumable contents from the unit.

2. Unplug the electrical cord from its socket.

3. Remove the door(s)/drawer(s).

Disposal and Recycling 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Environmental Requirements

This model is intended for indoor/interior applications only

and is not to be used in installations that are open/

exposed to natural elements.

This unit is designed to operate between 50°F (10°C) and

100°F (38°C). Higher ambient temperatures may reduce

the unit’s ability to reach low temperatures and/or reduce

ice production on applicable models.

For best performance, keep the unit out of direct sunlight

and away from heat generating equipment.

In climates where high humidity and dew points are

present, condensation may appear on outside surfaces.

This is considered normal. The condensation will

evaporate when the humidity drops.

CAUTION

Damages caused by ambient temperatures of

40°F (4°C) or below are not covered by the

warranty.

Environmental Requirements 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Electrical

WARNING

SHOCK HAZARD — Electrical Grounding

Required. Never attempt to repair or perform

maintenance on the unit until the electricity has

been disconnected.

Never remove the round grounding prong from

the plug and never use a two-prong grounding

adapter.

Altering, cutting or removing power cord,

removing power plug, or direct wiring can cause

serious injury, fire, loss of property and/or life,

and will void the warranty.

Never use an extension cord to connect power to

the unit.

Always keep your working area dry.

Electrical installation must observe all state and

local codes. This unit requires connection to a

grounded (three-prong), polarized receptacle

that has been placed by a qualified electrician.

The unit requires a grounded and polarized 115 VAC,

60 Hz, 15A power supply (normal household current). An

individual, properly grounded branch circuit or circuit

breaker is recommended. A GFCI (ground fault circuit

interrupter) is usually not required for fixed location

appliances and is not recommended for your unit because

it could be prone to nuisance tripping. However, be sure

to consult your local codes.

See CUTOUT DIMENSIONS for recommended receptacle

location.

Electrical 1

USER GUIDE

(102 mm)

(178 mm)

24"

(610 mm)

24-1/4"

(616 mm)

34-1/4"

(870 mm)

35-1/8"

(892 mm)

Preferred location for electrical outlet is in adjacent cabinet.

5/8"

(16 mm)

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Cutout Dimensions

PREPARE SITE

Your U-Line product has been designed for either free-

standing or built-in installation. When built-in, your unit

does not require additional air space for top, sides, or

rear. However, the front grille must NOT be obstructed,

and clearance is required for an electrical connection in

the rear.

CAUTION

Unit can NOT be installed behind a closed cabinet

door.

CUTOUT DIMENSIONS

Cutout Dimensions 1

USER GUIDE

3-9/16" (91 mm)

34-1/8" to 35-1/8"

23-1/4

" (591 mm)

(Includes

3/4

" [20 mm] Integrated Panel)

24" (610 mm)

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Product Dimensions

(867 mm to 892 mm)

Product Dimensions 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Side-by-Side Installation

Two units may be installed side-by-side.

Cutout width for a side-by-side installation is the cutout

dimension of a single unit times two.

No trim kit is required. However, 1/4" (6 mm) of space

needs to be maintained between the units to ensure

unobstructed door swing.

Units must operate from separate, properly grounded

electrical receptacles placed according to each unit’s

electrical specifications requirements.

Side-by-Side Installation with Bracket

1. Slide both units out so screws on top of units are easily

accessible.

3. Place bracket over holes and attach to unit with two

screws removed in step 2 using a T-25 Torx driver.

Tighten screws fully.

4. Gently push units into position. Be careful not to

entangle the electrical cord or water line, if applicable.

5. Re-check the leveling, from front to back and side to

side. Make any necessary adjustments. The unit’s top

surface should be approximately 1/8" (3 mm) below

the countertop.

2. Remove screws as shown below.

Side-by-Side Installation 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Anti-Tip Bracket

1. Slide unit out so screws on top of unit are easily

accessible.

2. Remove the two screws from the opposite side of the

hinge assembly using a T-25 Torx driver (see below).

NOTE: 1224 models shown with four screws. 1215 models

only have three screws, but same screws are used in both

applications.

FLOOR MOUNTED ANTI-TIP INSTALLATION

1. Locate two anti-tip brackets included in the kit.

2. Place the unit into the area where it will be installed.

Check the door, sides, and top for a proper fit. Also

test to make sure the door opens and closes freely.

3. Remove grille and place a mark on the floor at the

front of the unit. Also place a mark on the floor in the

center of the unit.

3. Place bracket (part #14154) over holes and attach to

unit with two screws removed in step 2 using a T-25

Torx driver. Tighten screws fully.

4. Gently push unit into position. Be careful not to

entangle the electrical cord or water line, if applicable.

5. Check to be sure the unit is level from front to back

and side to side. Make any necessary adjustments.

The unit’s top surface should be approximately 1/8"

(3 mm) below the countertop.

6. Secure bracket into adjoining surface.

Anti-Tip Bracket 1

USER GUIDE

Back wall

Back of unit

Front of unit

Surrounding

area (Top view)

1024/1224 WC 1215 WC

A 11-1/16" (281 mm) 6-9/16" (167 mm)

B 20-1/4" (514 mm) 20-1/4" (514 mm)

1024/1224 WC 1215 WC

A 11-1/16" (281 mm) 6-9/16" (167 mm)

B 20-1/4" (514 mm) 20-1/4" (514 mm)

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

4. Remove the unit. Using a square, extend center line

“B” (see chart below). This line serves as the back

edge for the anti-tip brackets. From the center line,

measure “A” to the left and right. This line is the outer

edge of each bracket.

5. Place the anti-tip brackets on the floor against the line

drawn for the outer edge. Mark spots for the screw

holes.

Surrounding

area (Top view)

Drill holes and

mount anti-tip

Front

unit

brackets to ﬂoor

Back

unit

Back wall

6. Use a 1/8" drill to make two starter holes and fasten

the anti-tip brackets to the floor using the screws

provided.

7. Place the unit back into position, making sure the feet

engage the anti-tip brackets properly. Check the

alignment of the lines made on the floor in step 3 with

the position of the front feet to ensure proper

positioning.

Anti-Tip Bracket 2

USER GUIDE

Turn to Adjust

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

General Installation

LEVELING INFORMATION

1. Use a level to

confirm the unit is

level. Level should

be placed along top

edge and side edge

as shown.

2. If the unit is not level, adjust the legs on the corners of

the unit as necessary.

INSTALLATION

1. Plug in the power/electrical cord.

2. Gently push the unit into position. Be careful not to

entangle the cord.

3. Re-check the leveling, from front to back and side to

side. Make any necessary adjustments. The unit’s top

surface should be approximately 1/8" (3 mm) below

the countertop.

4. Remove the interior packing material and wipe out the

inside of the unit with a clean, water-dampened cloth.

3. Confirm the unit is level after each adjustment and

repeat the previous steps until the unit is level.

INSTALLATION TIP

If the room floor is higher than the floor in the cutout

opening, adjust the rear legs to achieve a total unit rear

height of 1/8" (3 mm) less than the opening’s rear height.

Shorten the unit height in the front by adjusting the front

legs. This allows the unit to be gently tipped into the

opening. Readjust the front legs to level the unit after it is

correctly positioned in the opening.

General Installation 1

USER GUIDE

NOTICE

BACK SURFACE MUST HAVE AMPLE FLAT SURFACE TO MOUNT OVERLAY FRAME FLAT AND WITHOUT INTERFERENCE

2-3/4" (70 mm)

Integrated Frame

3/4" (20 mm)

23-3/4"

(603 mm)

30-1/4" (768 mm)

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Integrated Frame

Due to differences in surrounding cabinetry the

panel may not perfectly align with door. The

procedure below is designed to provide a

finished integrated panel that seamlessly

integrates with surrounding cabinetry.

The door panel must not weigh more than 20 lbs

(10 kg).

It is important to ensure that all drilled holes are

drilled to the correct depth in order to avoid

splits in the wood when hardware is installed.

When applying an integrated panel to a unit,

ensure that both sides are finished in order to

prevent warping. In some frame installations,

the panel may be visible through the glass while

the door is open.

2. Optional: Stain or Finish panel to desired stain or color.

Be sure to closely follow the instructions provided by

the manufacturer.

3. Optional: Install handles and hardware.

Integrated Frame Dimensions

A full integrated door panel completely covers the door

frame and provides a built-in appearance.

Integrated Frame Preparation

1. Cut the panels to the dimensions listed in the diagram

below.

Integrated Panel Dimensions 1

USER GUIDE

NOTICE

Align Panel

Against

Door/Drawer

Edge First

Align Top Of Panel With Highest Point Of Door/Drawer

Door

Panel

Integrated Panel

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Integrated Panel Installation

1. Fully open door/drawer.

2. Starting at corner, pull

gasket away from door/

drawer.

3. Continue to pull gasket

free from gasket channel.

4. Upon removal, lay gasket down on a flat surface.

5. The panel should be aligned with the outside edge

(opposite the hinge) and high enough to align with the

highest point in the door/drawer.

6. Secure integrated

panel to door/drawer

Bar

Clamp

using clamps. A

robust tape may also

be used. U-Line

recommends the use

of bar clamps to

Door/Drawer

secure the panel to

the door/drawer. If

using tape, be

Wood Panel

certain the tape will

not damage panel

finish upon removal.

7. Using a 7/64" (3 mm)

Bar

Clamp

drill bit, drill 6 pilot

holes into the wood

panel 1/2" (12 mm)

deep using the holes in the door/drawer frame as a

guide.

Due to differences in floor construction or

surrounding cabinetry, the panel may not sit

flush with the top of the door/drawer.

It is important to ensure that all drilled holes are

drilled to the correct depth in order to avoid

splits in the wood when hardwood is installed.

8. Locate 6 of the #6x 1-1/4" (32 mm) screws provided

with your unit.

9. Using a Phillips screwdriver, place one screw into each

of the 6 pilot holes and screw down. Do not overtighten

screws.

10.Be sure the screws force their way past the opening on

the gasket channel and sit flush against the bottom of

the channel.

Integrated Panel Installation 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

11.Remove clamps from door/drawer.

If panel requires additional adjustment after

removing clamps, slightly loosen each screw and

adjust panel as necessary. Tighten screws upon

completion.

12.Starting at the corners, re-install the gasket into the

gasket channel in the frame. Make sure the gasket is

fully seated. This may take some force.

Integrated Panel Installation 2

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Grille - Plinth Installation

REMOVING AND INSTALLING GRILLE

WARNING

Disconnect electric power to the unit before

removing the grille.

When using the unit, the grille (plinth strip/base

fascia) must be installed.

WARNING

DO NOT touch the condenser fins. The condenser

fins are SHARP and can be easily damaged.

Removing the grille

1. Disconnect power to the unit.

2. Loosen the two screws (1).

3. Remove grille (2) from unit.

Installing the grille

1. Align cabinet and grille holes and secure, but do not

over tighten grille screws (1).

2. Reconnect power to the unit.

Grille - Plinth Installation 1

USER GUIDE

Wall Wall

Door Swing

2-1/8" Min.

(54 mm)

1/4" Min.

(6 mm)

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Door Swing

Units have a zero clearance for the door to open 90°,

when installed adjacent to cabinets.

Stainless Steel and black and white models require 2-1/8"

(54 mm) door clearance to accommodate the handle if

installed next to a wall.

Integrated models require 1/4" (6 mm) clearance if

installed next to a wall. Allow for additional space for any

knobs or pulls installed on the integrated panel/frame.

Door Swing 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Door Stop

Your U-Line unit was shipped to you with the optional

90° pin(s). (Models that are 15" wide include 1 pin. Models

that are 24" wide include 2 pins.) The unit’s door will open

freely without a fixed opening angle limitation. If you

would like the door stop at 90° follow these instructions.

The pin is designed to stop the door at 90° under

normal operating conditions. It is not designed

for excessive force. Do not use the door to move

the unit in/out of the cutout during installation.

If your unit is already undercounter, it might

need to be moved out/forward to access the

hinge.

1. Locate the threaded pin.

3. On 24" models, a second pin is included for the bottom

hinge. Repeat steps above for second hinge.

NOTE: Threaded pin will be inserted from the bottom.

4. Carefully slide your unit back in place.

2. With the door between 0° (closed) and 90° and using a

3/32" hex driver, install the threaded pin through the

hinge.

The pin can be removed to return the door swing

back to its original state by unscrewing the

threaded pin.

Door Stop 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Door Adjustments

DOOR ALIGNMENT AND ADJUSTMENT

Align and adjust the door if it is not level or is not sealing

properly. If the door is not sealed, the unit may not cool

properly, or excessive frost may form in the interior.

Properly aligned, the door’s gasket should be

firmly in contact with the cabinet all the way

around the door (no gaps). Carefully examine

the door’s gasket to ensure that it is firmly in

contact with the cabinet. Also make sure the

door gasket is not pinched on the hinge side of

the door.

TO ALIGN AND ADJUST THE DOOR

Remove grille:

Remove the grille (see GRILLE-PLINTH INSTALLATION section of this guide).

TO REVERSE THE DOOR

Remove grille:

Remove the grille (see GRILLE-PLINTH INSTALLATION

section of this guide).

Remove top hinge and door:

1. Loosen (do not remove) top and bottom hinge screws.

2. Align door squarely with cabinet.

3. Make sure gasket is firmly in contact with cabinet all

the way around the door (no gaps).

4. Tighten bottom hinge screws.

5. Tighten top hinge screws.

REVERSING THE DOOR

Location of the unit may make it desirable to mount the

door on the opposite side of the cabinet.

The hinge hardware will be removed and installed on the

opposite side of the cabinet.

1. Hold door to keep it from falling.

2. Remove top hinge from cabinet by removing three

screws. Set aside and save for possible future use.

Door Adjustments 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

3. Remove door by tilting forward and lifting door off

bottom hinge. Retain shoulder washers; they will be

reused.

4. Remove four screws from hinge holes on the opposite

side. Reinstall into holes where the hinge was

removed. Take care not to scratch cabinet.

Remove and reinstall bottom hinge:

1. Remove bottom hinge from cabinet by removing three

screws.

3. Rotate gasket 180°, aligning notch with magnet

assembly and pressing firmly into the gasket channel

starting at the corners.

4. Rotate door 180° to reverse.

Install top hinge and door:

1. Use alternate hinge supplied with unit and reinstall the

screws. Do not tighten..

2. Lift the door on to the bottom hinge.

2. Remove corresponding screws on opposite side of

cabinet.

3. Flip hinge plate over and reinstall on opposite side.

Prepare door for reinstallation:

1. Remove gasket. This will reveal mounting holes for the

magnet assembly

2. Remove magnet assembly from door with T-10 TORX

driver. Be sure to only remove the two screws holding

the assembly to the door. Reinstall on the opposite end

of the door

3. Align flat edge of the hinge with the outer edge of the

unit.

4. Tighten three screws.

Align and adjust the door:

Align and adjust the door (see DOOR ALIGNMENT AND

ADJUSTMENT).

Install grille:

Install the grille.

Door Adjustments 2

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

SHIFTING WINE RACK SPACERS (OPTIONAL)

Only perform these steps if you require wine

rack clearance with a 90° door opening. Doors

which are allowed to open past 90° do not

require this step.

1. Remove wine rack (see WINE RACK INSTALLATION in

Maintenance).

2. Starting from the side that has the spacers (previously

unaltered units will be on the right hand side from the

factory), remove 2 screws, slide and spacer.

5. Place the spacer in between the liner and slide.

6. Install original hardware.

7. Slide wine rack back into position.

3. Reinstall the slide with the original 2 screws.

4. Remove 2 screws from the other side.

Door Adjustments 3

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Wood Trim Finishing

The wine rack fronts are solid natural beech wood. They

are factory coated with a clear vinyl sealer, which will

sufficiently protect the wood in normal use.

You may coat the trim with stain and/or a final finish to

match surrounding cabinetry.

CAUTION

You MUST remove the wood trim from the unit

for staining or finishing to prevent permanent

damage to the inner liner of the unit. Allow stain

or finish to dry thoroughly (at least 24 hours for

each coat) following the product manufacturer’s

instructions before reinstallation. Not following

this warning may cause the inner liner of the

unit to have a permanent odor, which the

warranty will not cover.

U-Line recommends Minwax

and Minwax Polycrylic

Never use oil based stains or finishes.

On glass door models, the stain may appear

darker when viewed through the glass.

Follow the manufacturers instructions for the

stain and/or finish you select.

Brand Water Based Stains

Protective Finish.

Wood Trim Finishing 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Free Standing Kit

The free standing kit is an optional accessory. It is only

used when unit is not installed in surrounding cabinetry.

To install the kit:

1. Remove grille (see GRILLE-PLINTH INSTALLATION

section).

2. Place shell accessory over front and back of cabinet

base, aligning holes of shell accessory with the holes

on the base. Insert sheet metal screw in back of base.

3. Align front hole with hole in shell accessory, hole in

base, and hole in grille. Tighten screw.

Free Standing Kit 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

First Use

All U-Line controls are preset at the factory. Initial startup

requires no adjustments.

U-Line recommends allowing the unit to run

overnight before loading with product. As warm

air rises, the temperature inside the unit tends

to be slightly warmer at the top and slightly

cooler at the bottom.

When plugged in, the unit will begin operating under the

factory default settings. If the unit was turned off during

installation, simply press and the unit will immediately

switch on. To turn the unit off, press .

First Use 1

USER GUIDE

Up Down Light Power

Not

Used LED

and

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Control Operation

CONTROL FUNCTION GUIDE

FUNCTION COMMAND DISPLAY/OPTIONS

ON/OFF Press and release Unit will immediately turn ON or OFF.

Toggle lights

Adjust refrigerator set

point

View temperature in unit Press together and release

Toggle between F/C Hold for 5 seconds The display will change units.

DOOR ALERT NOTIFICATION

When the door is left open for more than 5 minutes:

• An audible tone will sound for several seconds every

minute.

• “dr” will appear in display.

Close door to silence alert and reset.

Press and release to leave interior

light on for 3 hours

Press and release

Glass door wine and beverage centers only.

When the “F” or “C” in the display is flashing, press

to adjust the set point temperature.

The display will flash and then toggle from set point

to temperature in unit.

Control Operation 1

USER GUIDE

12 3456 7

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE



Sabbath Mode

This unit is Star-K certified and offers a Sabbath mode.

Sabbath mode disables system responses to user initiated

activities and all external functions, including lighting,

display and audible alarms. The unit will still maintain

internal temperatures and set points. View a full list of

Star-K certified U-Line units at www.star-k.org.

To enable Sabbath Mode:

1. Press (4) and hold for ten seconds and release (the

°F/°C symbol will flash briefly at the end of the ten

second period).

2. The interior light and control display (3) will go dark

until user resets mode.

3. NOTE: Although the display will not be visible, the

temperature controls in the unit remain active and

preserve the interior temperature.

Sabbath Mode remains active until (4) is quickly

pressed and released.

Sabbath Mode 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Airflow and Product Loading

The unit requires proper airflow to perform at its

highest efficiency. Do not block the front grille,

or the unit will not perform as expected. Do not

install the unit behind a door. When loading your

unit, leave space between the evaporator and

product loaded. Anything in direct contact with

the evaporator is subject to freezing.

When properly loaded, your U-Line unit will store up to 48

(750 ml) bottles of wine.

Airflow and Product Loading 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

U-Line Wine Guide

LOOKING BEHIND THE LABEL

To most, wine is a delicious mystery. We purchase it,

uncork it, and savor its taste and beauty. But there is so

much more to true wine appreciation. Many secrets are

simply too good to keep bottled up.

WINE SELECTIONS SUGGESTIONS

Selecting the right wine for the right occasion can

sometimes be a seemingly awkward or difficult task for

the beginning wine enthusiast. We would therefore like to

present you with a few suggestions which may provide a

little more confidence and enjoyment when choosing and

serving your wines.

When selecting wines, keep an open mind and do not be

afraid to be adventurous. Do not view the subject of wine

so seriously it discourages you from learning and

discovering for fear of embarrassment if something is

incorrect. Wine is best viewed as a hobby and enjoyed.

Guide To Common Styles Of Wine

Red Wines

Full-Bodied Dry California

Medium-Bodied Dry California

Light-Bodied Dry French

White Wines

Full-Bodied Dry California

Medium-Bodied Dry California

Light-Bodied Dry French Chablis, Muscadet,

Full-Bodied, Very Sweet

Medium-Bodied, Semi-Sweet

Light-Bodied Off Dry Germany Rhine, Mosel, Riesling

French Italian

French

Italian

French

Germany French Hungary

California Germany

Zinfandel, Cabernet Rhone, Chateauneuf-du- Pape Barbaresco, Barolo

Pinot Noir Bordeaux, Burgundy

Beaujolais Chianti, Bardolino

Chardonnay Montrachet, Meursault Puligny- Montrachet

Sauvignon-Blanc Pouilly-Fuisse, Sancerre, Vouvray, Graves

Pouilly-Fume

Beerenauslese Sauternes Tokay

Gewurtztraminer Liebfraumilch

When assembling your collection, try not to become

obsessed with “Vintages.” Although a chart can be a useful

tool, generalizations about a specific year have led more

than one collector to disappointment. Often an “Off Year”

will provide a better value and more drinking enjoyment.

The primary guideline to the subject of wine is your own

palate. Do not be afraid to make mistakes. Experiment,

discover, but most of all, enjoy yourself and your new U-

Line product.

Matching Food and Wine

Although there are no hard fast rules for matching wine to

food, observe some guidelines. Delicate dishes should be

accompanied by lighter more delicate wines. Full-flavored

foods should be matched with fuller-bodied wines.

As a general rule, one should aim to ascend in flavor and

quality of wines served.

Serve a: Before a:

DRY wine SWEET wine

WHITE wine RED wine

YOUNG wine OLD wine

LIGHT-BODIED wine FULL-BODIED wine

Any step back in quality will be noticed. If a fine wine is

tasted prior to a lesser wine, many of the fine wine’s

subtle qualities may be missed.

U-Line Wine Guide 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Common Food and Wine Matches

Foods Wines

Fish, Shell Fish, Crab, Oysters Dry White Wines, Light

Beef, Venison Full-Bodied Red Wines

Pork, Veal, Lamb and Poultry Light-Bodied Red Wines

Fruit Sweet White and Sparkling

A Toast to Wine Truths

Like the grapes themselves, many wine myths have been

cultivated over the centuries.

Myth 1: Most wines taste better when aged.

Truth: In fact, less than 5% of wines produced today are

meant to be aged. Most wines are crafted to be consumed

within the first one to two years.

Myth 2: Wines should be uncorked and decanted allowing

them to “breathe.”

Truth: To breathe or not breathe? While it is better to

allow a young tannic Red to breathe in a glass or decanter

to soften the tannins, an old Red reaches a stage in its life

where it should be enjoyed soon after opening. Allow an

old Red to breathe for a short time to dissipate any off

odors. Most white wines can be served, ideally, 10-15

minutes after opening.

Sparkling or Extra Dry

Champagne

Wines

The Cork: A Mystery on Its Own

Cork Presentation. The ritual of the presentation of the

cork has a rich and fascinating history dating back to the

late 1800’s. A phylloxera (root louse) devastation to the

vineyards severely limited the supply of great wines.

Restaurateurs would remove labels on inferior wines and

replace them with labels from superior wines. This made it

necessary for patrons to protect themselves by checking

the branding on the cork to ensure that what they ordered

was, in fact, what they were served.

When presented with a cork today, feel it to check for its

integrity, read and match the branding on the cork to the

bottle and set it aside. There is little to be learned from

the cork. The proof is in the wine.

“Corked” wines. If you’ve ever had a wine that smelled or

tasted of mold, you’ve experienced a wine that may have

been “corked.” Today, between five and eight percent of

wines are tainted with Trichloroanisole (TCA). This

substance, found naturally in plants and trees, is imparted

to the wine through the cork. Corked wines are a major

concern for winemakers as it destroys millions of cases

per year and puts reputations at stake. Amazing as it may

seem twist-off caps may offer a better alternative and

many great wineries in California, Australia and New

Zealand are pioneering the trend.

Myth 3: When age worthy wines peak, they must be

consumed almost immediately.

Truth: Most great wines reach a plateau period rather

than a peak. Great Bordeaux’s may have as much as a

10-year plateau before fading.

Myth 4: Wine color does not change with aging.

Truth: As red wines age they get lighter in color while

whites get darker.

U-Line Wine Guide 2

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Common Tasting Terms IDEAL WINE STORAGE CONSIDERATIONS

Terminology Description

Acidity A critical element of wine that is responsible

for preserving the wines freshness. Excess acidity results in an overly tart and sour wine.

Balance A desired trait where tannin, fruit and acidity

are in total harmony. Wines with good balance tend to age gracefully.

Body The weight and presence of wine in the

mouth provided by the alcohol and tannin level. Full-bodied wines tend to have this strong concentration.

Bouquet The blending of a wine’s aroma within the

bottle over a period of time, caused by volatile acidity.

Complex A subjective term often used in tasting. A

wine is said to be complex if it offers a variety of flavors and scents that continue to evolve as it develops.

Flabby A wine that lacks structure, or is heavy to

the taste, lacks acidity.

Full-Bodied Wine high in alcohol and extract, generally

speaking, fills the mouth, powerful.

Lean Generally describes wines that are slim,

lacking of generosity or thin.

Oaky A desirable flavor imparted to wine if done in

moderation. Most wines are aged in oak barrels one to three years, thereby receiving this toasty oak characteristic. However, if a weak wine is left in contact too long with an oak barrel it will tend to be overpowered with an oaky taste.

Tannin Tannins are extracted from the grape skins

and stems and are necessary for a well- balanced red wine. Tannins are easily identified in wine tasting as the drying sensation over the gums. Tannins generally fade as a wine ages.

Temperature: The most important element about

storage temperature is stability. If wine is kept in a stable

environment between 40°F (7°C) and 65°F (21°C), it will

remain sound. A small 1-2 degree temperature fluctuation

within a stable environment is acceptable. Larger

temperature fluctuations can affect the corks ability to

seal, allowing the wine to “leak” from the bottle.

Humidity: The traditional view on humidity maintains

that wines should be stored on their sides in 50% - 80%

relative humidity to ensure cork moisture and proper fit in

the bottle. Contemporary wisdom suggests that the cork

surface is too small to be impacted by humidity. Further

the cork is sealed with a metal or wax capsule making

humidity penetration impossible. The concept of a humid

storage environment was derived from the necessity of

wineries to maintain moisture in their cellars to keep

wooden barrel staves swollen, preventing wine

evaporation and product loss. In fact, vineyards estimate

as much as a 10% product loss per year due to

evaporation while wine is aging in the wooden barrels.

Humidity, however, was not intended for the modern

home cellar where wine is stored in glass bottles with

sealed corks.

Light: UV rays are not only harmful to people, they are

damaging to wines - especially those in clear bottles.

Since oxygen molecules in wine absorb UV rays, wine

should never be stored in direct light for long periods of

time.

Vibration: Provided that sediment is left undistributed

and particles are not suspended, vibration in a storage

environment is not an issue. Wines can become flat or

tired when voids and vacuums are created inside the wine

bottle. In order to create voids and vacuums within a

liquid, aggressive motion or shaking of the wine bottle

would have to occur.

U-Line Wine Guide 3

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

The Right Temperature for Wine

Temperature Wines

Approximately 60°F (15°C) Red

50°F - 55°F (10°C -12°C) White

Approximately 45°F (7°C) Sparkling

Wine Captain® Models - A Touch of Elegance

In 1985 U-Line was the first North American appliance

manufacturer to develop a residential wine storage unit,

the Wine Captain®. Each U-Line Wine Captain® model is

designed to impress and inspire anyone with an interest in

wine by providing cellar conditions in stylish, undercounter

units. U-Line Wine Captain

temperatures, a 50% internal relative humidity and

protection from UV light rays. U-Line has the largest

product offering available, making storing, presenting,

and sharing your wine effortless and elegant.

models offer stable storage

U-Line Wine Guide 4

USER GUIDE

NOTE: After stocking, allow unit to stabilize product

temperatures for 24 hours.

Use These Racks For Larger Diameter Bottles

& Champange

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Recommended Wine Storage

Specially designed horizontal wine racks properly position

the bottles so the wine remains in contact with the cork,

which ensures the cork does not become dry.

U-Line recommends arranging wine bottles as shown in

the illustrations below.

Racks 1 through 5:

Recommended Wine Storage 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Cleaning

EXTERIOR CLEANING

Vinyl Clad (Black or White)

Clean surfaces with a mild detergent and warm water

solution. Do not use solvent-based or abrasive cleaners.

Use a soft sponge and rinse with clean water. Wipe with a

soft, clean towel to prevent water spotting.

Clean any glass surfaces with a non-chlorine glass

cleaner.

Stainless Models

Stainless door panels, handles and frames can discolor

when exposed to chlorine gas, pool chemicals, saltwater

or cleaners with bleach.

Keep your stainless unit looking new by cleaning with a

good quality all-in-one stainless steel cleaner and polish

monthly. For best results use Claire

Polish and Cleaner. Comparable products are acceptable.

Frequent cleaning will remove surface contamination that

could lead to rust. Some installations may require cleaning

weekly.

Stainless Steel

If any surface discoloring or rusting appears, clean it

quickly with Bon-Ami

and a nonabrasive cloth. Always clean with the grain.

Always finish with Claire

Cleaner or comparable product to prevent further

problems.

Using abrasive pads such as Scotchbrite™ will cause the graining in the stainless steel to become blurred.

Rust not cleaned up promptly can penetrate the surface of the stainless steel and complete removal of the rust may not be possible.

Integrated Models

To clean integrated panels, use household cleaner per the

cabinet manufacturer’s recommendation.

INTERIOR CLEANING

Disconnect power to the unit.

Clean the interior and all removed components using a

mild nonabrasive detergent and warm water solution

applied with a soft sponge or non-abrasive cloth.

or Barkeepers Friend Cleanser®

Stainless Steel Polish and

Do not clean with steel wool pads.

Do not use stainless steel cleaners polishes on any glass surfaces.

Clean any glass surfaces with a non-chlorine glass

cleaner.

Do not use cleaners not specifically intended for stainless steel on stainless surfaces (this includes glass, tile and counter cleaners).

Rinse the interior using a soft sponge and clean water.

Do not use any solvent-based or abrasive

cleaners. These types of cleaners may transfer taste to

the interior products and damage or discolor the interior.

DEFROSTING

Under normal conditions this unit does not require manual

defrosting. Minor frost on the rear wall or visible through

the evaporator plate vents is normal and will melt during

each off cycle.

If there is excessive build-up of 1/4" (6 mm) or more,

manually defrost the unit.

Ensure the door is closing and sealing properly.

Cleaning 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

High ambient temperature and excessive humidity can

also produce frost.

CAUTION

DO NOT use an ice pick or other sharp

instrument to help speed up defrosting. These

instruments can puncture the inner lining or

damage the cooling unit. DO NOT use any type of

heater to defrost. Using a heater to speed up

defrosting can cause personal injury and

damage to the inner lining.

The drain pan was not designed to capture the

water created when manually defrosting. To

prevent water from overflowing the drain pan,

place towels or other absorbent materials over

the interior drain trough (under the evaporator)

before defrosting.

To defrost:

1. Disconnect power to the unit.

2. Remove all products from the interior.

3. Prop the door in an open position (2 in. [50 mm]

minimum).

4. Allow the frost to melt naturally.

5. After the frost melts completely clean the interior and

all removed components. (See INTERIOR CLEANING).

6. When the interior is dry, reconnect power and turn unit

on.

Cleaning 2

USER GUIDE

NOTICE

Condenser

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Cleaning Condenser

INTERVAL - EVERY SIX MONTHS

To maintain operational efficiency, keep the front grille

free of dust and lint, and clean the condenser when

necessary. Depending on environmental conditions, more

or less frequent cleaning may be necessary.

WARNING

Disconnect electric power to the unit before

cleaning the condenser.

WARNING

DO NOT touch the condenser fins. The condenser

fins are SHARP and can be easily damaged.

DO NOT use any type of cleaner on the

condenser unit.

1. Remove the grille.

2. Clean the condenser coil using a using a soft brush

with a “combing” action or vacuum cleaner.

3. Install the grille.

Cleaning Condenser 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Wine Rack Installation

To remove rack from the cabinet:

1. Remove any bottles stored on the rack.

2. Grasp the end of the rack and gently slide it out until it stops.

3. Press the left rack release lever down. At the same time, lift the matching right rack release lever up. Pull the rack out until it is free of the tracks and the cabinet.

Do not remove the track rails from the cabinet.

To insert rack in the cabinet:

1. Align the left and right rack channels with the tracks in the cabinet. Ensure an even track engagement on both sides by gently pushing the rack into the cabinet until it stops.

2. Before reloading the rack, ensure proper movement of the travel stops in the left and right track rails by pulling the rack out gently until it stops.

Wine Rack Installation 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Extended Non-Use

VACATION/HOLIDAY, PROLONGED SHUTDOWN

The following steps are recommended for periods of

extended non-use:

1. Remove all consumable content from the unit.

2. Disconnect the power cord from its outlet/socket and

leave it disconnected until the unit is returned to

service.

3. If ice is on the evaporator, allow ice to thaw naturally.

4. Clean and dry the interior of the unit. Ensure all water

has been removed from the unit.

5. The door must remain open to prevent formation of

mold and mildew. Open door a minimum of 2"

(50 mm) to provide the necessary ventilation.

WINTERIZATION

If the unit will be exposed to temperatures of 40°F (5°C)

or less, the steps above must be followed.

For questions regarding winterization, please

call U-Line at +1.800.779.2547.

CAUTION

Damage caused by freezing temperatures is not

covered by the warranty.

Extended Non-Use 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Troubleshooting

BEFORE CALLING FOR SERVICE

If you think your U-Line product is malfunctioning, read

the CONTROL OPERATION section to clearly understand

the function of the control.

If the problem persists, read the NORMAL OPERATING

SOUNDS and TROUBLESHOOTING GUIDE sections below

to help you quickly identify common problems and

possible causes and remedies. Most often, this will resolve

the problem without the need to call for service.

IF SERVICE IS REQUIRED

If you do not understand a troubleshooting remedy, or

your product needs service, contact U-Line Corporation

directly at +1.800.779.2547.

When you call, you will need your product Model and

Serial Numbers. This information appears on the Model

and Serial number plate located on the upper right or rear

wall of the interior of your product.

NORMAL OPERATING SOUNDS

All models incorporate rigid foam insulated cabinets to

provide high thermal efficiency and maximum sound

reduction for its internal working components. Despite this

technology, your model may make sounds that are

unfamiliar.

Normal operating sounds may be more noticeable because

of the unit’s environment. Hard surfaces such as cabinets,

wood, vinyl or tiled floors and paneled walls have a

tendency to reflect normal appliance operating noises.

Listed below are common refrigeration components with a

brief description of the normal operating sounds they

make. NOTE: Your product may not contain all the

components listed.

• Evaporator: Refrigerant flowing through an evaporator

may sound like boiling liquid.

• Condenser Fan: Air moving through a condenser may

be heard.

• Automatic Defrost Drain Pan: Water may be heard

dripping or running into the drain pan when the unit is

in the defrost cycle.

TROUBLESHOOTING GUIDE

DANGER

ELECTROCUTION HAZARD. Never attempt to

repair or perform maintenance on the unit

before disconnecting the main electrical power.

Troubleshooting - What to check when problems occur:

Problem Possible Cause and Remedy

Interior Light Does Not Illuminate.

Light Remains on When Door Is Closed.

Unit Develops Frost on Internal Surfaces.

Unit Develops Condensation on External Surfaces.

Product Is Freezing.

If the unit is cooling, it may be in Sabbath mode.

Turn off light switch if equipped. Adjust light actuator bracket on bottom of

door.

Frost on the rear wall is normal and will melt during each off cycle.

If there is excessive build-up of 1/4" or more, manually defrost the unit.

Ensure the door is closing and sealing properly.

High ambient temperature and excessive humidity can also produce frost.

The unit is exposed to excessive humidity. Moisture will dissipate as humidity levels decrease.

Because product in contact with the rear wall may freeze, ensure no product is touching the rear wall.

Adjust the temperature to a warmer set point.

• Compressor: The compressor makes a hum or pulsing

sound that may be heard when it operates.

Troubleshooting 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Problem Possible Cause and Remedy

Product Is Not Cold Enough.

Air temperature does not indicate product temperature. See CHECKING PRODUCT TEMPERATURE below.

Adjust the temperate to a cooler set point. Ensure unit is not located in excessive

ambient temperatures or in direct sunlight. Ensure the door is closing and sealing

properly. Ensure the interior light has not remained on

too long. Ensure nothing is blocking the front grille,

found at the bottom of the unit. Ensure the condenser coil is clean and free of

any dirt or lint build-up.

CHECKING PRODUCT TEMPERATURE

Causes which affect the internal temperatures of the cabinet include:

• Temperature setting.

• Ambient temperature where installed.

• Installation in direct sunlight or near a heat source.

• The number of door openings and the time the door is

open.

• The time the internal light is illuminated. (This mainly

affects product on the top rack or shelf.)

• Obstruction of front grille or condenser.

To check the actual product temperature in the unit:

1. Partially fill a plastic (nonbreakable) bottle with water.

2. Insert an accurate thermometer.

3. Tighten the bottle cap securely.

4. Place the bottle in the desired area for 24 hours.

5. Avoid opening the unit during the testing period.

6. After 24 hours, check the temperature of the water. If

required, adjust the temperature control in a small

increment (see CONTROL OPERATION).

Troubleshooting 2

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

U-Line Corporation (U-Line) Limited Warranty

One Year Limited Warranty

For one year from the date of original purchase, this U-Line product warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase. All service provided by U- Line under the above warranty must be performed by U-Line factory authorized service, unless otherwise specified by U-Line. Service provided during normal business hours.

Available Second Year Limited Warranty

Beyond the standard one year warranty outlined above, U-Line offers an extension of the one year warranty coverage for an additional second year from the date of purchase, free of charge. To take advantage of this second year warranty, you must register your product with U-Line within two months from the date of purchase at u-line.com providing proof of purchase.

Five Year Sealed System Limited Warranty

For five years from the date of original purchase, U-Line will repair or replace the following parts, labor not included, that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier, and all connecting tubing. All service provided by U-Line under the above warranty must be performed by U-Line factory authorized service, unless otherwise specified by U-Line. Service provided during normal business hours.

Terms

These warranties apply only to products installed in any one of the fifty states of the United States, the District of Columbia, or the ten provinces of Canada. The warranties do not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service, repair, acts of God, fire, flood or other natural disasters. The product must be installed, operated, and maintained in accordance with the U-Line User Guide.

The remedies described above for each warranty are the only ones that U-Line will provide, either under these warranties or under any warranty arising by operation of law. U-Line will not be responsible for any consequential or incidental damages arising from the breach of these warranties or any other warranty, whether express, implied, or statutory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. These warranties give you specific legal rights, and you may also have other rights which vary from state to state.

Any warranty that may be implied in connection with your purchase or use of the product, including any warranty of merchantability or any warranty fit for a particular purpose is limited to the duration of these warranties, and only extends to five years in duration for the parts described in the section related to the five ye ar limited warranty above. Some states do not all ow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

• The warranties only apply to the original purchaser and are non-transferable.

• The second year and five year warranties cover products installed and used for normal residential or designated marine use only.

• The warranties apply to units operated outside only if designed for outdoor use by model and serial number.

• Replacement water filters, light bulbs, and other consumable parts are not covered by these warranties.

• The start of U-Line’s obligation is limited to four years after the shipment date from U-Line.

• In-home instruction on how to use your product is not covered by these warranties.

• Food, beverage, and medicine loss are not covered by these warranties.

• If the product is located in an area where U-Line factory authorized service is not available, you may be responsible for a trip charge or you may be required to bring the product to a U-Line factory authorized service location at your own cost and expense.

• Units purchased after use as floor displays no coverage is provided for cosmetic defects.

• Signal issues related to Wi-Fi connectivity are not covered by these warranties.

, and/or certified reconditioned units, are covered by the limited one year warranty only and

For parts and service assistance, or to find U-Line factory authorized service near you, contact U-Line: 8900 N. 55th Street, Milwaukee, WI 53223 • u-line.com • onlineservice@u-line.com • +1.800.779.2547

Warranty 1

USER GUIDE

42350_B WIRING DIAGRAM

POWER CORD

ASSEMBLY

GROUND:

GREEN or GREEN W/ YELLOW

HOT:

BLACK (115v)

BROWN (220-240v)

NEUTRAL

HOT

RELAY

EMBRACO

COMPRESSOR

GREEN or

GREEN W/ YELLOW

GROUND:

115

VOLT

PLUG

220-240 VOLT

PLUG

OVERLOAD

NEUTRAL:

WHITE (115v)

DARK BLUE (220-240v)

(TO COMPRESSOR)

NEUTRAL:

WHITE (115v)

DARK BLUE (220-240v)

BLUE (115V)

LIGHT BLUE (220V-240V)

(TO COMPRESSOR)

CONTROL

BOARD

ZONE TEMP

FUSE

EVAP TEMP

L/T DOOR SWITCH

AMBIENT TEMP

R/B LIGHT

L/T LIGHT

COND FAN

EVAP TEMP

R/B DOOR SWITCH

CAP

PROGRAMING

TO DISPLAY

OPEN

ANTENNA

J10

HOT (LIGHT BLUE)

OVERLOAD

EMBRACO COMPRESSOR

220-240 VOLT

RELAY

GREEN W/ YELLOW

GROUND:

NEUTRAL:

DARK BLUE

CAP.

BROWN BLUE

115 VOLT

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Wire Diagram

Wire Diagram 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Product Liability

Field service technicians are authorized to make an initial

assessment in the event of reported damages. If there are

any questions about the process involved, the technician

should call U-Line for further explanation.

While inspecting for defects or installation issues, photos

should be taken to document any damages or issues

found.

During the assessment, if the service technician is able to

find the source of the damage and it can be resolved by

replacement of a part, the servicer is authorized to

replace the part in question. The part that caused the

damage must be returned to U-Line in its entirety. The

part must be clearly labeled with the serial number of the

unit it was removed from, the date, and the servicer who

removed the part.

If the service technician determines the damage is the

result of installation issues (water connection/drain, etc.),

the consumer would be notified and the issues shall be

resolved at the direction of the consumer.

If damage is evident and the service technician is unable

to find the source, U-Line must be contacted at 1-800-

799-2547 for further direction

8900 N. 55th Street • Milwaukee, WI 53223

T: +1.414.354.0300 • F: +1.414.354.354.5696

Website: www.u-line.com

Right product. Right place.

Right temperature Since 1962.

Product Liability 1

USER GUIDE

14 30911 1 2 XXXX

Year

Month

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Warranty Claims

The following information defines the parameters for filing

a warranty claim:

• Valid serial number needed

• Valid model number needed

• Narda (or equivalent) form or submitted online at

www.u-line.com

• 60 day submittal deadline from date of completed

service

• Only one repair or unit per warranty claim

• Refrigerant should be labeled and included on the labor

submittal

warranty status. We also accept the following

information to verify warranty status:

• New Construction Occupancy Documents

•Closing Paperwork

• Final Billing – Remodel

Noting all of the following on the warranty claim will be

considered proof of purchase, hard copy will not be

required:

• Name of the selling Dealer

• Date of purchase/installation

• Order or Invoice number (if available)

• Door and water level adjustments are covered 30 days

from install date.

Serial Number Requirements:

A typical serial number is shown above. The first two

digits of the first segment, 14, represents the production

year. The number between the dashes, 12, represents the

production month. In most cases, warranty status can be

verified by the production date information within the

serial number.

• Description of document reviewed (i.e. store receipt,

closing paperwork, etc)

Parts and labor claims are paid separately. Indicate part

numbers and description for parts used in the warranty

repair. Include the purchase invoice and name of the parts

supplier used to procure the parts.

• Alternatively, a Proof of Purchase (or equivalent) may

submitted with the warranty claim to document

Warranty Claims 1

Parts

26 27

U-1224WCINT-00B

Item Description U-Line P/N

1 Anti tip bracket w/screws 80-54221-00

2 Back panel 80-54204-00

3 Compressor electricals only 80-54149-00

4 Compressor w/electricals 80-54150-00

5 Condenser assembly 80-54264-00

6 Condenser fan w/screws 80-54014-00

7 Control Housing 80-54265-00

8 Display module 80-54252-00

9 Display rack, btm 80-54318-00

10 Door assembly w/ hinges 80-54263-00

11 Gasket, door 80-54213-00

12 Drain pan w/double sided tape 80-54217-00

13 Drier 80-54055-00

14 Evaporator assembly 80-54262-00

15 Grille w/screws 80-54267-00

16 Hinges(2) w/screws 80-54208-00

17 LED light strip and cover assy 80-54000-00

18 Leg Levelers (4) 80-54201-00

19 Magnet w/brkt and screws 80-54250-00

20 Main board (no case or wires) 80-54008-00

21 Packaging 80-54209-00

22 Power cord 80-54171-00

23 Rack Assembly 80-54269-00

24 Reed switch 80-54284-00

25 Slide Assembly 80-54219-00

26 Thermistor (1 pc) 80-54006-00

27 Thermistor cover and pin 80-54023-00

28 Wire harness, board 80-54251-00

29 Wood front w/screws 80-54283-00

Parts 1

USER GUIDE

NOTICE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Ordering Replacement Parts

If you have a purchasing account, please utilize our

service website to order parts.

Orders may also be placed by Fax or phone. See our

contact information below:

www.U-LineService.com (with service login)

FAX Number: +1.414.354.5696

Phone Number: +1.800.779.2547

Use only genuine U-Line replacement parts. The

use of non-U-Line parts can reduce speed of ice

production, cause water to overflow from ice

maker mold, damage the unit, and void the

warranty.

Warranty parts will be shipped at no charge after U-Line

confirms warranty status. Please provide the model, serial

number, part number and part description. Some parts

will require color or voltage information.

If U-Line requires the return of original parts, we will

inform you when the parts order is taken. This

requirement will be noted on your packing list. A prepaid

shipping label will be included with the replacement part.

Please enclose a copy of the parts packing list and any

labor claims with your return. Please be sure the model

and serial numbers are legible on the paperwork. Tag the

part with the reported defect.

When ordering a non-warranty part, you will need an open

account and tax exemption on file at U-Line. Another

option would be to visit www.u-line.com to locate an

authorized parts distributor in your area.

Ordering Replacement Parts 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

System Diagnosis Guide

REFRIGERATION SYSTEM DIAGNOSIS GUIDE

System Condition

Normal Normal Slightly below

Overcharge Higher than

Undercharge Lower than

Partial Restriction

Complete Restriction

No Gas 0 PSIG to 25" Room

Suction Pressure

normal

Somewhat lower than normal vacuum

In deep vacuum

Suction Line

room temperature

Very cold may frost heavily

Warm-near room temperature

Warm - near room temperature

Room temperature (cool)

temperature (cool)

Compressor Discharge

Very hot Very hot Warm Cold Normal

Slightly warm to hot

Hot Warm Warm Extremely cold

Very hot Top passes

Room temperature (cool)

Cool to hot Room

Condenser Capillary

Hot to warm Cool Cold Higher than

warm - Lower passes cool (near room temperature) due to liquid

Room temperature (cool)

temperature (cool)

Tube

Room temperature (cool) or colder

Room temperature (cool)

Evaporator Wattage

normal

Lower than near inlet - Outlet below room temperature

Extremely cold near inlet - Outlet below room temperature backing up

No refrigeration Lower than

normal

Lower than

normal

System Diagnosis Guide 1

USER GUIDE

OVERLOAD PROTECTOR

STARTING RELAY

CAPACITOR

RELAY COVER

ULIN_0368_A

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Compressor Specifications

DANGER

Electrocution can cause death or serious injury.

Burns from hot or cold surfaces can cause

serious injury. Take precautions when servicing

this unit.

EMX20CLC

Disconnect the power source.

Do not stand in standing water when working

around electrical appliances.

Make sure the surfaces you touch are not hot or

frozen.

Do not touch a bare circuit board unless you are

wearing an anti-static wrist strap that is

grounded to an electrical ground or grounded

water pipe.

Refrigerant R600a

Voltage 115 - 127 VAC

Frequency 60 Hz

Run Cap 12μF/165 VAC

Start Winding 6.7 Ohm at 77°F

Run Winding 12.6 Ohm at 77°F

LRA 3.7 A

FLA 0.5 A

Starting Device 8EA14C

Overload 4TM142RFBYY-53

* All resistance readings are ±10%

Handle circuit boards carefully and avoid

touching components.

To measure the start winding resistance, measure across

the C and S pins.

To measure the run winding resistance, measure across

the C and R pins.

Also check S to R and you should get the sum of the run

and start windings.

To ensure the windings are not shorted, check the S and R

to ground.

Compressor Specifications 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Troubleshooting - Extended

CAUTION

Never attempt to repair or perform maintenance

on the unit until the main electrical power has

been disconnected from the unit.

SPECIFIC ERRORS AND ISSUES

The technically advanced diagnostic capabilities of the

electronic controls utilized on the 1200 and 2200 series

units allows for easy and thorough troubleshooting.

Navigation of the control is the key and is explained in the

CONTROL OPERATION section of the manual, along with

control button layout, control function descriptions, a

service mode menu and service menu selection

explanations.

NORMAL OPERATING SOUNDS

All models incorporate rigid foam insulated cabinets to

provide high thermal efficiency and maximum sound

reduction for its internal working components. Despite this

technology, your model may make sounds that are

unfamiliar.

Normal operating sounds may be more noticeable because

of the unit’s environment. Hard surfaces such as cabinets,

wood, vinyl or tiled floors and paneled walls have a

tendency to reflect normal appliance operating noises.

Listed below are common refrigeration components with a

brief description of the normal operating sounds they

make. NOTE: Your product may not contain all the

components listed.

• Compressor: The compressor makes a hum or pulsing

sound that may be heard when it operates.

Verification of temperature and thermistor performance

can be identified by directly viewing thermistor readings in

the service mode.

Component failure issues can be identified through service

mode menu #19, “Component Testing.” Individual

components can be switched on and off to check for both

proper function of a specific component and also delivery

of supply voltage to the components through the relays

and DC outputs located on the relay/power board.

Included in this section are some diagnostic tips and of

course, if additional help is required please contact the

U-Line Corp, “Customer Care Facility” at +1.800.779.2547

for assistance.

• Evaporator: Refrigerant flowing through an evaporator

may sound like boiling liquid.

• Condenser Fan: Air moving through a condenser may

be heard.

• Automatic Defrost Drain Pan: Water may be heard

dripping or running into the drain pan when the unit is

in the defrost cycle.

Solenoid Valves: An occasional clicking sound may be

heard as solenoid valves are operated.

Troubleshooting - Extended 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

TROUBLESHOOTING GUIDE

Concern Potential Causes Suggested Remedy

Not Cooling Compressor overheating Verify proper air flow through condenser. Is condenser clean?

Confirm condenser fan operation.

Confirm proper compressor operating voltage. Use #19, Component Testing in Service Mode.

Compressor not operating Confirm proper compressor operating voltage. Use #19, Component

Compressor operating - no cooling Refer to System Diagnosis Guide.

Evaporator fan not operating Use #19, Component Testing in Service Mode.

Frozen Product Control set too cold Adjust Set Point Temp accordingly.

Review logged error codes Refer to #14, Error Log in Service Mode.

Thermistor failure Check Error Log in Service Mode, OHM thermistor.

Frost Buildup Inside Unit

Display Not Working

Internal Lights Not Working

Noisy Refrigeration tubing touching cabinet Carefully reposition tubing.

Door Ajar or Restricted from Closing Check door clearance to adjoining cabinetry. Check distribution of

Evaporator fan not operating Use Relay Toggle, Component Testing in Service Mode.

Thermistor failure Check Error Log.

Unit placed in Sabbath mode? Press and hold for 5 seconds to check.

Display unplugged Verify that both ends of the display wiring are firmly connected.

Display wiring broken or damaged Perform continuity test of wiring and replace as needed.

Control Setting Unit set to Sabbath Mode. Press and hold for 5 seconds to check.

Door switch misaligned or defective Check the function of reed switch and door magnet adjustment.

Fan blade obstruction (wiring, foam insulation, packaging material)

Testing in Service Mode.

Test overload and relay, replace as needed.

product in unit.

Remove obstruction.

Troubleshooting - Extended 2

USER GUIDE

NOTICE

Check Voltage

At Wall Outlet

Verify Voltage At

Main Control

Voltage Input

Check Fuse F1 For Continuity

Replace

Reed Switch

Replace Main

Board

Replace

Fuse

Replace

Power Cord

Alert Customer

Of Power Failure

Is the Reed

Switch Operating

Properly?

Inspect

Customer UI

and Data Cable

Connect Test Display

Cycle Power And Check

For Operation

No Voltage

Voltage

Continuity

Operating

Not Operating

No Continuity

Yes

Voltage

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

MAIN CONTROL

The main control board is very robust and is rarely the

cause of system issues. It is important to fully diagnose

the board for any suspected failures before attempting to

remove the board for replacement or service. Follow the

guidelines below to fully test and diagnose the main

control.

Power Fault

If the unit does not (or seems to not) power on, follow the

flow chart below to help diagnose the issue. Before

beginning it is important to first verify the unit is not

simply set to sabbath mode.

Testing The Main Control

If the main control is suspected of being faulty, the

following procedure should be performed to verify main

control for functionality.

Relay & DC Outputs

One of the primary functions of the main control is to

operate the multiple relay and DC outputs during each

cycle. Verify proper operation of these relays using the

following procedure.

1. Enter “Relay Toggle” through the service menu.

Frequently toggling the compressor relay could

force the compressor into overload. The

compressor will automatically deactivate during

an overload and will remain deactivated until the

overload switch cools. This could take some

time. It is important to allow the compressor at

least 5 minutes off time between relay cycles.

2. Toggle the relay. Its related component should

activate / deactivate with the switching of the relay. If

it does not, test component.

Other Suspected Main Control Faults

If other components have been ruled out as being faulty

but the unit continues to have operating issues, it is most

likely due to a configuration error. Configuration errors

can be cleared by restoring the unit to its factory default

setting. Factory defaults may be restored through the

service menu.

CAUTION

Precautions must be taken while working with

live electrical equipment. Be sure to follow

proper safety procedures while performing tests

on live systems.

Troubleshooting - Extended 3

USER GUIDE

Magnet Close To Switch

(Door Closed)

(Switch Closed)

Magnet Away From Switch

(Door Open)

(Switch Open)

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

REED SWITCH

A reed switch is used to monitor door state. When the

door is closed magnetic force pulls the reed to its contact

and closes the circuit which turns the light and display off.

When the door is open the reed pulls away from the

contact and opens the circuit. If the door is left open for

longer than 5 minutes, the switch will trigger an error code

and set an audible warning.

Troubleshooting - Extended 4

USER GUIDE

123 4567

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Control Operation - Service

UI BUTTON LAYOUT

1. Hidden Button

-Accesses Service Menu

-No LED directly above. All LEDs turn on with button activation except #7.

Up Button

-Increases temperature

-Navigates through service menu

-LED activated with button activation.

Down Button

-Decreases temperature

-Navigates through service menu

-LED activated with button activation

Light Button

-Activates light for 3 hours on s elect models

-Used to select items in service menu

-LED activated with button activation

Power Button

-Turns unit off/on

-LED activated with button activation (only turning unit off)

6. Clean Button

-Activates Clean Cycle on CLR models

-LED activated with button activation

LED

-No button

Control Operation - Service 1

USER GUIDE

and

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

CONTROL FUNCTION QUICK GUIDE FUNCTION COMMAND DISPLAY/OPTIONS

ON/OFF Press and release Unit will immediately turn ON or OFF

Toggle lights

Adjust refrigerator temperature

View temperature in unit Push and release the together

Toggle between F/C Hold the for five seconds The display will change units.

Press and release to leave interior light on for 3 hours

Push and release

Glass door wine captains and beverage centers only.

When the “F” or “C” in the display is flashi ng, push to adjust the set point temperature.

The display will flash and then toggle from set point to temperature in unit.

DOOR ALERT NOTIFICATION

When the door is left open for more than 5 minutes:

• An audible tone will sound for several seconds every minute.

• “dr” will appear in display.

Close door to silence alert and reset.

VIEWING ACTUAL TEMPERATURE

In viewing temperature in these modes any offsets are taken into account. This means that if you place a therm- istor in a known temperature, let’s say ice water, it may not read the 32°F that you would assume. If the control offset was preset at -3°F while you placed the thermistor in an icebath, the actual thermistor reading when viewing actual temperature would read 35°F . In the unit this would cause the cabinet to push itself 3° cooler. To view pure thermistor readings you must go into the service menu and choose the correct option.

T o view the thermistor temperature, push and release the up and down keys. The display will show the corr ected refrigerator temperature.

When the degree symbol is flashing the unit will allow the use of the control for demonstrations. The unit can be left in this mode indefinitely.

SERVICE MODE

This mode has options available for service diagnostics. To enter the mode hold the hidden key for 10 seconds. The display will show “0.” When in this mode use the up and down arrows to select the desired option. The LIGHT key is the ENTER key and will initiate the function. If changing a setting, you must press the LIGHT key again to retain the changed setting. T o exit the service mode scroll to option “0” and press the LIGHT key. After five minutes of not touching any keys the mode will also exit automatically.

SHOWROOM MODE

This mode is designed to show units in a display environ- ment. When in this mode the only functions will be the control and cabinet lights. The compressor, fans, etc. will not operate. To enter/exit this mode hold the light key and the power key for 5 seconds. The display will flash once and beep and the degree symbol will begin to flash.

Control Operation - Service 2

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

SERVICE MODE GUIDE

# Service Mode Menu Item

1 View thermistor #1 (no offsets) 2 View thermistor #2 (no offsets) 3 View thermistor #3 (no offsets) 4 View thermistor #4 (no offsets) 5 Adjust thermistor #1 offset 6 Adjust thermistor #2 offset 7 Adjust thermistor #3 offset 8 Adjust thermistor #4 offset

9 View thermistor #2 set point no offsets 10 View thermistor #3 set point no offsets 11 View thermistor #4 set point no offsets 12 Adjust defrost interval 3 to 24 hours 13 Adjust defrost duration 0 to 99 minutes 14 View error log 15 Clear error log 16 Adjust thermistor #1 differential 17 Adjust evaporator fan delay in minutes (start of cooling

cycle) 0 - 99 minutes

18 Adjust evaporator fan delay in minutes (after cooling

cycle stops) 0 - 99 minutes 19 Individual component toggle 20 Model number indicato r 21 Light all LED segments of display 22 View defrost cycles 23 View compressor run time 24 Activate defrost/harvest 25 Restore factory defaults 26 View software version - main board 27 View software version - user interface 28 Login period 29 Factory test mode

0Exit service mode

NAVIGATE SERVICE MODE

SERVICE MODE GUIDE

1. THERMISTOR 1 — ZONE

This shows the pure thermistor reading with no offsets taken into account.

2. THERMISTOR 2 — EVAPORATOR

This shows the pure thermistor reading with no offsets taken into account.

3. Does not apply to this model.

4. Does not apply to this model.

5. THERMISTOR 1 — ZONE OFFSET

(DO NOT MAKE AN ADJUSTMENT TO THIS WITHOUT CONTACTING TECH LINE: 800-779- 2547)

This calibration is only to be used if actual

temperature at thermistor #1 is off from set point.

By adjusting the offset higher we can force the unit to drive the temperature down below the set point. (example: adjusting from 0 to +2 will drop the unit temperature 2 degrees)

6. THERMISTOR 2 — EVAPORATOR OFFSET

(DO NOT MAKE AN ADJUSTMENT TO THIS WITHOUT CONTACTING TECH LINE: 800-779- 2547)

7. Does not apply to this model.

8. Does not apply to this model.

9. THERMISTOR 2 — SET POINT MINUS

OFFSET

This shows the thermistor reading with offsets taken into account.

10. Does not apply to this model.

11. Does not apply to this model.

12. ADJUST DEFROST INTERVAL — 3 TO 24

HOURS

This will adjust the interval between defrosts from 3 to 24 hours. Adjusting from the factory settings may cause undesired temperature in the refrigerator section.

Use up or down arrows to scroll through the menu. Use the light bulb key to enter or exit menu. If values

have been change d, they will be saved when exiting.

13. ADJUST DEFROST DURATION — 0 TO 99

MINUTES

The length of the defrost can be adjusted 0 to 99 minutes long. The other defrost parameters still apply. Lengthening a defrost may cause higher than normal temperatures in the refrigerator section.

Control Operation - Service 3

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

14. VIEW ERROR LOG

A list of the errors in the order they occurred will scroll once on the display. All errors are logged in memory. Only door error is displayed on the display and has an audible signal.

E0:

Door 1 (upper) open.

E1: Thermistor 1 open. E2: Thermistor 2 open. E3: Thermistor 3 open. E4: Thermistor 4 open (Does not apply to this

model).

E5: Thermistor 1 shorted. E6: Thermistor 2 shorted. E7: Thermistor 3 shorted. E8: Thermistor 4 shorted (Does not apply to this

model).

E9: Door 2 (lower) open. P1: Pump Circuit open (Does not apply to this

model).

15. CLEAR ERROR LOG

To clear errors, press and hold

(5 seconds)

when CLR is flashing.

16. THERMISTOR — 1 DIFFERENTIAL

This number should not be adjusted.

17. Does not apply to this model.

18. Does not apply to this model.

21. LIGHT ALL LED SEGMENTS

This will illuminate all the LEDs on the display to ensure they work properly.

22. VIEW DEFROST CYCLES

Displays the number of defrosts that have occurred in the past 24 hours.

23. VIEW COMPRESSOR RUNTIME

This will show the number of minutes the compressor has run in the prior cycle (or current cycle if the compressor was running when service mode was entered).

24. ACTIVATE DEFROST/HARVEST

Turns on the hot gas bypass valve allowing hot gas to circulate through the evaporator causing frost to melt.

25. RESTORE FACTORY DEFAULTS

Will restore all adjustable functions to their factory settings.

26. SOFTWARE VERSION — MAIN BOARD

Displays software version of the main control board.

19. INDIVIDUAL COMPONENT TOGGLE

Display # Relay/Output

0 Exit 2 Relay 2 3 Relay 3 4 Relay 4 5 Relay 5 6 Relay 6

7 Relay 7 8 DC Output 1

9 DC Output 2 10 DC Output 3 11 DC Output 4 12 DC Output 5

SEE RELAY/OUTPUT CHART

20. MODEL NUMBER INDICATOR

Displays the two-digit model number of the specific unit. See model list table.

27. SOFTWARE VERSION —

USER INTERFACE

Displays software version of the user interface.

28. LOG IN PERIOD

Factory use only - do not adjust.

29. FACTORY TEST MODE

Should be 0.

0. EXIT SERVICE MODE

Control Operation - Service 4

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

MODEL LIST

1000 MODEL

1215R 07 2218R 05 2245R 55 1215WC 12 2218RGL 04 2245DC 54 1224BEV 13 2218WC 06 2245WC 56 1224DWR 08 2224BEV 00 2260DC 50 1224R 14 2224FZR 11 2260FZR 57 1224RF 09 2224R 02 2260R 52 1224RSOD 10 2224RGL 01 2260RDC 51 1224WC 15 2224WC 03 2260WC 53 CLR1215 18 2224ZWC 59 2260ZWC 58 CO1224F 19 ADA24R 17

INDICATOR

2000 (120V) MODEL

INDICATOR

2000 (230V) MODEL

INDICATOR

PROGRAMMING THE UNIT TO CORRECT MODEL NUMBER

1. Disconnect the unit from power source.

2. Push and hold the U-Line button.

3. While still holding the U-Line button, plug the

unit into the appropriate power source.

4. When the flashing digits appear (3-5 seconds), use the up and down arrow buttons to select the

appropriate model number*.

*(See Above “Model List”)

5. Press the light bulb button once.

6. The display will blink, and then will appear as the

programmed display.

Control Operation - Service 5

USER GUIDE

Name Relay 2 Relay 3 Relay 4 Relay 5 Relay 6 Relay 7

1215R N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

1215WC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

124BEV N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

1224DWR

N/A N/A N/A N/A Compressor Top Light Evaporator Fan Condenser Fan N/A Bottom Light

1224R N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

1224RF N/A N/A Pan Heater Hot Gas Valve N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

1224RSOD N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

1224WC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

ADA24R N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

CLR1215 N/A Pump Water Valve Hot Gas Valve

Compressor Light N/A N/A N/A N/A

CO1224F Ice Maker 2 Ice Maker 1 Pan Heater Hot Gas Valve N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2218R N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2218RGL N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2218WC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2224BEV N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2224R N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2224RGL N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2224WC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2224ZWC N/A N/A vl2 vl1 N/A Compressor Top Light N/A Condenser Fan N/A Bottom Light

2245R N/A Hot Gas Valve N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2245RDC N/A Hot Gas Valve N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2245WC N/A Hot Gas Valve N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2260DC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2260R N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2260RDC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2260WC N/A N/A N/A N/A N/A Compressor Light Evaporator Fan Condenser Fan N/A N/A

2260ZWC N/A N/A vl2 vl1 N/A Compressor Top Light N/A Condenser Fan N/A Bottom Light

5HOD\2XWSXW&KDUW

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

ut 5

Out

ut 4

Out

ut 3

Out

ut 2

Out

ut 1

Out

Condenser

Fan

Mullion

Heater

Control Operation - Service 6

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Thermistors

Thermistors are used for various temperature readings.

Thermistors provide reliable temperature readings using a

resistance which varies based on surrounding

temperatures. If a faulty thermistor is suspected it may

be tested using an accurate ohmmeter.

Both thermistors in the unit are identical. If a thermistor is

suspected of being defective, the resistance can be

verified. Place the thermistor in an ice water bath, the

resistance should read 16.1k OHMs +/-5% on your meter.

Thermistor connections must be kept clean. A thermistor

connection that has become corroded can cause

resistance values from the thermistor to change as they

pass through a dirty connection to the board.

It is for that reason that we apply dielectric grease to all of

our thermistor connections. Dielectric grease will help to

keep thermistor connections clean and dry.

If you change a thermistor in the unit please re-apply

dielectric grease to the connection. If you encounter a

dirty thermistor connection, you should replace the

thermistor and the thermistor harness.

Thermistor error information can be found in the Control

Operations - Service section.

This unit has two thermistors.

Thermistor one (Zone):

Located along the right hand side wall. It is used to

maintain the operating temperature within that zone.

Thermistor two (Evaporator):

Located on the evaporator. It is used for defrost.

THERMISTOR FAILURE

Zone Thermistor

1000 Series Self Preservation Mode:

The unit will cycle on for 10 minutes then off for 40

minutes.

Evaporator Thermistor

If the evaporator thermistor fails, the unit will rely on a

preset defrost timer during defrost cycles. The unit will

otherwise operate normally. Refer to defrost section.

Thermistor Resistance Data

Temp (F) Temp (C)

-40 -40 169157

-31 -35 121795

-22 -30 88766

-13 -25 65333

-4 -20 48614

5-15 36503

14 -10 27681

23 -5 21166

32 0 16330

41 5 12696

50 10 9951

59 15 7855

68 20 6246

77 25 5000

86 30 4029

95 35 3266

104 40 2665

113 45 2186

122 50 1803

131 55 1495

140 60 1247

149 65 1044

158 70 879

167 75 743

176 80 631

* (+/-5%)

Nominal Resistance

(OHMS)*

If the zone thermistor in the unit fails, the unit will

continue to cool in a backup mode (Self Preservation

Mode) to preserve the integrity of the contents. The unit

will otherwise operate normally.

Thermistor 1

USER GUIDE

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Defrost

The models below have automatic or frost free design and do not require manual defrosting under normal conditions.

Defrost Settings

Base Model Variant(s) Compressor Run Time

1224 RF 12 45 15 (-9)

1215/1224/2218/2245/

2224/2260

1215/1224/2218/2245/

2224/2260

CO29 F 12 18 n/a

CO1224 F 12 18 45 (7)

1224FZR Freezer Mode 6 45 42(6)

1224FZR Refrigerator Mode 12 45 42(6)

WC, ZWC 12 45 45 (7)

R, RSOD, RDC,

BEV, DC, DWR, RGL

Between Defrost (Hours)

12 45 42 (6)

Duration in Minutes

(Maximum)

Stop Temperature

°F (°C)

The defrost settings for 3000 series models are determined by zone.

Defrost Settings by Zone (3000 Series)

Zones Compressor Run Time

Between Defrost (Hours)

Beverage/Drinks 12 5 60 42 (6)

Market/Fresh 12 5 60 42 (6)

Root/Root Cellar 12 5 60 45 (7)

Pantry 12 5 60 42 (6)

White Wine 12 5 60 45 (7)

Red Wine 12 5 60 45 (7)

Sparkling Wine 12 5 60 45 (7)

Polar 6 5 20 42 (6)

Deli 12 5 60 42 (6)

Duration in Minutes

(Minimum)

Duration in Minutes

(Maximum)

Stop Temperature

°F (°C)

Defrost 1

U-line U1224WCS13B User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual