Ubiquiti Networks Uag-xg User Manual
10G Rack-Mountable
Application Server
Model: UAS-XG
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi®
Application Server. This Quick Start Guide is designed to guide
you through installation and also includes warrantyterms.
Package Contents
UniFi Application Server
Rack-Mount Brackets
(Qty. 2)
Cage Nuts
(Qty. 4)
TERMS OF USE: All Ethernet cabling runs must use CAT6A (or above). It is the professional
installer’s responsibility to follow local country regulations, including operation within legal
frequency channels, output power, indoor cabling requirements, and Dynamic Frequency
Selection (DFS) requirements.
Bracket Screws
(Qty. 8)
Power Cord U Logo Stickers
(Qty. 2)
Mounting Screws
(Qty. 4)
10G Rack-Mountable
Application Server
Model: UAS-XG
Quick Start Guide
System Requirement
Web Browser: Google Chrome (Other browsers may have
limited functionality.)
Network Topology Example
US-16-XG
USG-PRO-4
LAN
UAS-XG
The UniFi Server requires a DHCP-enabled network to obtain
an IP address. Here is a sample network diagram using
thesedevices:
• UAS-XG The UniFi Application Server hosts the UniFi
Controller and UniFi Video software applications.
• US-16-XG Connect the 10G Ethernet ports from the
UAS-XG to the US-16-XG or other 10G-capable switches for
maximum throughput. Note that the UAS-XG’s Ethernet
ports are backwards-compatible with standard 1G ports if
10G is not available.
• USG-PRO-4 The UniFi Security Gateway Pro acts as the
DHCP server and connects to the internet.
WAN
Internet
Hardware Overview
Back Panel Ports
Power USB1-2 VGA
Port Description
Power
IPMI LAN
USB1-2
LAN1-2
VGA (Optional) Connect a monitor for console access.
Connect the included Power Cord to the Power
port.
(Optional) The dedicated RJ45 port supports
IPMI (Intelligent Platform Management
Interface) for monitoring and control.
(Optional) Connect USB 3.0 devices. Maximum
power per port is 5W (5V, 1A).
RJ45 ports support 1/10 Gbps Ethernet
connections.
IPMI LAN
LAN1-2
Back Panel LEDs
IPMI
Link
IPMI
Activity
LAN2
Activity
LAN2
Speed
IPMI LAN LEDs
LED State Status
Off No Link
Link
Amber Link Established
Off No Activity
Activity
Red Activity
LAN1/2 LEDs
LED State Status
Off No Link
Activity
Amber Flashing Indicates Activity
Off
Speed
Amber Link Established at 1 Gbps
No Connection or
Link Established at 10/100Mbps
Green Link Established at 10Gbps
LAN1
Activity
LAN1
Speed
Front Panel LEDs
LAN1/2
System
HDD1/2
System LED
Color State Status
Flashing Initializing
White
Steady Factory Defaults
Blue Steady Device Operating Nominally
LAN1/2 LEDs
State Status
Color
Steady Link Established at 1/10 Gbps
Green
Flashing Indicates Activity
HDD1/2 LEDs
State Status
Color
Green Flashing Indicates Read/Write Activity
Amber Steady Indicates HDD Error
Front Panel Ports
USB3/4
USB3-4 (Optional) Connect USB 2.0 devices. Maximum power
per port is 5W (5V, 1A).
Front Panel Buttons
ResetPower
Button Description
Power Press to turn the UniFi Server on or off.
Reset
The UniFiServer should be running after bootup
is complete, and the System LED is blue. Press
the Reset button for a softreboot.
Front Panel HDD Bays
Two 2 TB HDDs are pre-installed. If you want to replace an
HDD, follow these instructions:
1. Before replacing an HDD, ensure that the UniFi Server is
powered off to prevent any software disruption.
2. To replace an HDD, press the HDD bay door.
3. Once the door is released, rotate the door and pull the
HDD bay out.
4. Replace the pre-installed HDD with another HDD (optional)
and then close the HDD bay door.
*640-00281-05*
640-00281-05
Before You Begin
Remove the labels that secure the HDD bay doors.
1. Before removing the labels, ensure that the UniFi Server is
powered off to avoid disconnecting the hard drives while
the UniFi Server is powered on.
2. Pull the white part of the label.
3. Press the HDD bay door.
4. Once the door is released, rotate the door and pull the
HDD bay out.
5. Remove the rest of the label.
6. Push the HDD bay back in and close the HDD bay door.
7. Repeat steps 2-6 for the other label.
Loading...