Ubiquiti Networks RocketDis LW User Manual [en, de, es, fr, it]

airMAX® 2x2 PtP Bridge
Dish Antenna

Model: RD-5G30-LW

Introduction

Thank you for purchasing the Ubiquiti Networks® RocketDish™,
an airMAX® 2x2 PtP Bridge Dish Antenna. This Quick Start
Guide is designed to guide you through the installation of the
antenna. This Quick Start Guide also includes the warranty

terms and is for use with the RocketDish, modelRD-5G30-LW.

Package Contents

Dish Antenna Mounting

Upper Pole

Bracket

Hex Head Bolts

(M8, Qty. 5)

M10x100 Bolts

(Qty. 2)

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable
is designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.

Bracket

Support Arm Brace Screws

Lock Washers

(M8, Qty. 5)

Serrated

Flange Nuts

(M10, Qty. 2)

Antenna Feed Lower Pole

Flat Washers

(M8, Qty. 5)

M8x150 Carriage

Bolts (Qty. 4)

(M6, Qty. 4)

Stabilizer Brackets

Pole Clamps

(Qty. 2)

Bracket

Protective

Shroud

(Qty. 2)

Quick Start

airMAX® 2x2 PtP Bridge
Dish Antenna

Model: RD-5G30-LW

Guide

™

Installation Requirements

• Rocket™5ac PtP, Rocket5ac Lite, RocketM5 Titanium, or

RocketM5 (sold separately)

• Phillips screwdriver

• 13 mm wrench

• Wrench or channel lock pliers with 63.5 mm (2.5") capacity

• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded
through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Overview

Protective Shroud

Pole Clamp

Elevation Rod

Mounting Bracket

Pole Clamp

Stabilizer Brackets

Fully Assembled Back View

Installation

Important: Handle the Dish Reflector with care.

Deformations in its shape may reduce the RocketDish's
effectiveness.

1. Line up the alignment tabs of the Mounting Bracket with

the alignment slots of the Dish Reflector. Insert the tabs and
rotate the Mounting Bracket until they lock intoplace.

Note: Ensure that the antenna feed slot of the

Mounting Bracket lines up with the antenna feed slot
of the Dish Reflector, as shown below:

2. The Dish Reflector and Antenna Feed are keyed so the

Antenna Feed can only be installed in a single orientation.
Follow these steps:

a. Remove the knob from the Antenna Feed.
b. Line up the alignment pins of the Antenna Feed with

the alignment holes of the Dish Reflector and Mounting
Bracket.

Note: Ensure that the straight edge of the

Antenna Feed end (shown below) and arrow on
the Antenna Feed cap are pointing straight up.

c. Insert the Antenna Feed.

3. To secure the Antenna Feed to the Dish Reflector:

a. Replace the knob and tighten it by hand until the knob

touches the surface of the Mounting Bracket.

b. Use a wrench or channel lock pliers to tighten the knob

an additional ¼ turn. Do NOT over-tighten the knob.

Note: Ensure that the Antenna Feed is securely

attached by the knob.

Important: Do not handle the RocketDish by the Antenna

Feed once the feed is attached.

*640-00148-03*

640-00148-03

4. Attach the Rocket to the Mounting Bracket.

a. Align the mounting tabs on the back of the Rocket with

the Rocket mount.

b. Slide the Rocket down to lock it into place.

5. Attach the other end of the RF Cables to the RF connectors

on the Rocket in this combination: H to Chain 1 and V to
Chain 0. Then slide the jackets over the RF connectors to
protect them.

6. Attach the Protective Shroud.

a. Align the hash mark on the top of the shroud with the

notch on the Dish Antenna.

b. Rotate the shroud clockwise until it locks into place.

7. Attach two Hex Head Bolts, two Lock Washers, and two Flat

Washers to the bottom of the Mounting Bracket. Ensure that
there is a gap of 8 mm between each Flat Washer and the
Mounting Bracket.

Note: Ensure that each Lock Washer is always

installed between the Hex Head Bolt and Flat Washer.

Hex Head Bolt
Lock Washer
Flat Washer

8 mm

8. Attach the horizontal slot of the Support Arm to the Upper

Pole Bracket using a Hex Head Bolt, Lock Washer, and

FlatWasher.

Note: Ensure that the degree settings are the same

on both arms of the Upper Pole Bracket.

Degree markings

facing outward

9. Attach the Brace to the pole brackets using the four Screws.

10. Each M8x150 Carriage Bolt includes a serrated flange nut.

Remove these and use them in the next step.

11. Attach one Pole Clamp to each pole bracket.

a. Insert two M8x150 Carriage Bolts into each pole bracket.
b. Slide the hole of a Pole Clamp over one bolt of each

pole bracket.

c. Place one serrated flange nut on each bolt.

12. Attach the Stabilizer Brackets to the pole just beneath the

area where the RocketDish will be attached.

Note: The pole-bracket assembly can accommodate

a Ø 38 - 101mm pole.

a. Place one Stabilizer Bracket on each side of the pole.
b. Insert the two M10x100 Bolts into the Stabilizer Brackets.
c. Secure each bolt with one Serrated Flange Nut.

50 N-m

13. Attach the pole-bracket assembly to the pole:

a. Slide the slot of each Pole Clamp over the

corresponding M8x150 CarriageBolt.

b. Tighten the serrated flange nuts of the bolts to secure

the pole-bracket assembly to the pole.

Proper slot orientation

25 N-m

14. Lift the Dish Reflector and align the two lower Hex Head

Bolts with the slots on the Lower Pole Bracket. Seat the bolts

in the slots.

15. Attach each arm of the Upper Pole Bracket to the Mounting

Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer.

16. Before adjusting the tilt angle, ensure that the six Hex Head

Bolts are loose enough to allow movement.

IMPORTANT: If you cannot spin the washers freely by

hand, then loosen the Hex Head Bolts until you can.

17. To adjust the tilt angle, turn the screw head of the Elevation

Rod until the desired tilt is reached.

18. Lock the alignment by tightening all six Hex HeadBolts to

25 N-m.

Specifications

Dimensions 650 x 650 x386 mm (25.6 x 25.6 x 15.2")

Weight 7.4 kg (16.31 lb)

Frequency 5.1 - 5.9 GHz

Gain 30 dBi

Max. VSWR 1.6:1

Wind Survivability 200 km/h (125 mph)

Wind Loading 790 N @ 200 km/h (178 lbf @ 125 mph)

Polarization Dual Linear

F/B Ratio 30 dB

ETSI Specication EN 302 326 DN2

Mounting Universal Pole Mount, Rocket Bracket, and

RocketDish RD-5G30-LW

(Mount Included)

Weatherproof RF Jumpers Included

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from
lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;
(V) has been damaged or impaired as a result of using third party

firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.
In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements
are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.

Compliance

RF Exposure Warning

The antenna and transmitter must be installed to provide a separation
distance from all persons and must not be located or operating in
conjunction with any other antenna or transmitter. For the specific
separation distance, refer to the Quick Start Guide for your Rocket device
(transmitter).

L’antenne et l’émetteur doit être installé pour fournir une distance de
séparation de toute les personnes et ne doit pas être situé ou opérant en
conjonction avec une autre antenne ou un autre émetteur. Pour la distance
spécifique de séparation, se référer au Guide de démarrage rapide pour
votre appareil Rocket (l’émetteur).

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing
this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this
product should be disposed of separately from regular household waste
streams. It is your responsibility to dispose of this and other electric and
electronic equipment via designated collection facilities appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human
health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or
the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall
entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt
von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es
liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische
und elektronische Geräte über die dafür zuständigen und von der
Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu
entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder
städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das
Produkt erworben haben.

Español

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este
símbolo en el propio aparato y/o en su embalaje no deben eliminarse

junto con otros residuos urbanos no seleccionados. El símbolo indica

que el producto en cuestión debe separarse de los residuos domésticos

convencionales con vistas a su eliminación. Es responsabilidad suya

desechar este y cualesquiera otros aparatos eléctricos y electrónicos a
través de los puntos de recogida que ponen a su disposición el gobierno y

las autoridades locales. Al desechar y reciclar correctamente estos aparatos
estará contribuyendo a evitar posibles consecuencias negativas para el
medio ambiente y la salud de las personas. Si desea obtener información
más detallada sobre la eliminación segura de su aparato usado, consulte a
las autoridades locales, al servicio de recogida y eliminación de residuos de
su zona o pregunte en la tienda donde adquirió el producto.

Français

La directive européenne 2002/96/CE exige que l’équipement sur lequel
est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté
avec les autres ordures ménagères. Ce symbole indique que le produit
doit être éliminé dans un circuit distinct de celui pour les déchets des
ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout
autre matériel électrique ou électronique par les moyens de collecte
indiqués par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme ont pour
but de lutter contre l’impact néfaste potentiel de ce type de produits
sur l’environnement et la santé publique. Pour plus d’informations sur le
mode d’élimination de votre ancien équipement, veuillez prendre contact
avec les pouvoirs publics locaux, le service de traitement des déchets, ou
l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non

siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica
che questo prodotto non deve essere smaltito insieme ai normali rifiuti
domestici. È responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante le specifiche
strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il
corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze
potenzialmente negative per l’ambiente e per la salute dell’essere umano.
Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti
pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel
quale avete acquistato il prodotto.

Declaration of Conformity

Česky
[Czech]

Dansk
[Danish]

Nederlands
[Dutch]

English

Eesti
[Estonian]

Suomi
[Finnish]

Français
[French]

Deutsch
[German]

Ελληνική
[Greek]

Magyar
[Hungarian]

Íslenska
[Icelandic]

Italiano
[Italian]

Latviski
[Latvian]

UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS
device, je ve shod se základními po adavky a dal ími p íslu n mi
ustanoveními sm rnice 1999/5/ES.

Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende
udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav
og øvrige relevante krav i direktiv 1999/5/EF.

Hierbij verklaart UBIQUITI NETWORKS dat het toestel UBIQUITI
NETWORKS device, in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn 1999/5/EG.

Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI
NETWORKS device, voldoet aan de essentiële eisen en aan de
overige relevante bepalingen van Richtlijn 1999/5/EC.

Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI
NETWORKS device, is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.

Käesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITI
NETWORKS device, vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

UBIQUITI NETWORKS vakuuttaa täten että UBIQUITI NETWORKS
device, tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Par la présente UBIQUITI NETWORKS déclare que l’appareil
UBIQUITI NETWORKS, device est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.

Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI
NETWORKS Gerät, in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet. (BMWi)

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ UBIQUITI NETWORKS ΔΗΛΩΝΕΙ ΟΤΙ UBIQUITI
NETWORKS device, ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1995/5/ΕΚ.

Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a
UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS
device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í
tilskipun 1999/5/EC.

Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI
NETWORKS device, è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar o UBIQUITI NETWORKS deklarē, ka UBIQUITI NETWORKS ierīce,
atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.

Lietuviškai
[Lithuanian]

Malti
[Maltese]

Norsk
[Norwegian]

Slovensky
[Slovak]

Svenska
[Swedish]

Español
[Spanish]

Polski
[Polish]

Português
[Portuguese]

Română
[Romanian]

UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS
įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.

Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITI
NETWORKS device, jikkonforma mal- ti ijiet essenzjali u ma
provvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

UBIQUITI NETWORKS erklærer herved at utstyret UBIQUITI
NETWORKS device, er i samsvar med de grunnleggende krav og
øvrige relevante krav i direktiv 1999/5/EF.

UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKS
device, sp a základné po iadavky a v etky príslu né ustanovenia
Smernice 1999/5/ES.

Härmed intygar UBIQUITI NETWORKS att denna UBIQUITI
NETWORKS device, står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.

Por medio de la presente UBIQUITI NETWORKS declara que el
UBIQUITI NETWORKS device, cumple con los requisitos esenciales
y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.

Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt serii
UBIQUITI NETWORKS device, spełnia zasadnicze wymagania i inne
istotne postanowienia Dyrektywy 1999/5/EC.

UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device,
está conforme com os requisitos essenciais e outras disposições da
Directiva 1999/5/CE.

Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv
UBIQUITI NETWORKS este în conformitate cu cerințele esențiale și
alte prevederi relevante ale Directivei 1999/5/CE.

Online Resources

Support support.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com

www.ubnt.com

©2014-2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti

Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, Rocket,
RocketDish, and TOUGHCable are trademarks or registered trademarks of

UbiquitiNetworks,Inc. in the United States and in other countries. All other

trademarks are the property of their respective owners. JL030215