Ubiquiti edgepoint r6 Quick Start Manual

Intelligent WISP Control
with FiberProtect

™

Model: EP-R6

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgePoint™
Router. This Quick Start Guide is designed to guide you through
installation and includes the warranty terms.

Package Contents

EdgePoint Router Metal Strap Gigabit PoE (24V, 1.25A) with

Mounting Bracket

Intelligent WISP Control
with FiberProtect

™

Model: EP-R6

Power Cord Quick Start Guide

Installation Requirements

• Phillips screwdriver

• 7 mm socket wrench

• Ground wire – min. 10 AWG (5 mm

2

) and max. length: 1m. Asa

safety precaution, ground the EdgePoint to a grounded mast,
pole, tower, or grounding bar.

• Shielded Category 5 (or above) cabling should be used for all
wired Ethernet connections and should be grounded through
the AC ground of the PoE.

• We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial‑grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit: www.ubnt.com/toughcable

TERMS OF USE: Shielded Ethernet cable and earth grounding must be used as conditions of product
warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to
follow local country regulations, including operation within legal frequency channels, output power,
and Dynamic Frequency Selection (DFS) requirements.

1

Introduction

Hardware Overview

Ports Panel

Ground

Bonding Point

Reset

Interface

Description

Ground

Bonding Point

Used to secure a ground wire (not included).

Reset

There are two methods to reset the EP‑R6 to
factory defaults:

• Runtime reset (recommended) The
EP‑R6 should be running after bootup is
complete. Press and hold the Reset button
for about 10seconds until the eth4 LED
starts flashing and then becomes solidly lit.
After a few seconds, the LED will turn off,
and the EP‑R6 will automatically reboot.

• Power-on reset Disconnect power from
the EP‑R6. Press and hold the Reset button
while connecting power to the EP‑R6. Keep
holding the button until the eth4 LED starts
flashing and then stops flashing after a few
seconds.

2

EdgePoint EP‑R6 Quick Start Guide

Power Options

Either the VDC input or PoE input is used at any one time. If both
input types are connected, only the input type with the highest
voltage will be used; the other can be used as a backup. Any of the
input options can power any of the output options.

Power Input Options

• 24VDC, 3A

• 24V, 1.4A on eth0 (PoE In)

Power Output Options

• EdgePoint (required)

• Passive 24V, 2‑Pair PoE on

eth0-eth4

The number of devices that can be powered depends on the
power consumption of the specific devices. For example, if
you provide 24VDC, 1.25A, then you have 30W of power. If the
EdgePoint uses 7W (Max. Power Consumption), then you have
23W available for passive PoE output. Please check product
specifications for the power consumption values to use in your
calculations.

DC Input

VDC

Interface Description

VDC In

Terminal block connector accepts 24VDC, 3A
input to power the EdgePoint and passive

PoEoutput.

3

Hardware Overview

Ports

PoE In / eth0 eth1-4

eth5 / SFP

Interface

Description

PoE In/eth0

(24V PoE Out)

The RJ45 port supports 10/100/1000 Ethernet
connections and has PoE input or output
functionality:

• PoE Input Accepts 24V, 1.4A PoE input to
power the EdgePoint and PoE output.

• PoE Output You can configure the port for
24V 2‑pair PoE output.

Do NOT configure port eth0 in PoE output
mode if you are using it as a PoE input power
source.

eth1‑4

(24V PoE Out)

RJ45 ports support 10/100/1000 Ethernet
connections and passive 24V, 2‑pair PoE
output for airMAX® devices.

eth5/SFP

The SFP port is hot‑swappable and supports
100 Mbps or Gigabit fiber SFP modules.

Note: For extreme temperatures, please use industrial‑grade

fiber SFP modules.

4

EdgePoint EP‑R6 Quick Start Guide

Front Panel LEDs

LED State Status

power

Green EdgePoint Powered On

eth0‑eth4

Speed/

Link/Act

Off No Link

Green

10/100/1000Mbps (1 Gbps) Link
Flashing Indicates Activity

PoE

Output

Off No PoE

Green 24V Passive

eth5/SFP

Speed/

Link/Act

Off No Link

Green

100/1000Mbps (1 Gbps) Link
Flashing Indicates Activity

5

Hardware Overview

Hardware Installation

Pole Mounting

1. Open the Metal Strap and feed it through the mounting slots
on the back of the EdgePoint.

2. Wrap the Metal Strap around the pole. Use a 7 mm socket
wrench to turn the screw clockwise and securely fasten the
strap to the pole.

3. Proceed to the Grounding the EdgePoint section.

6

EdgePoint EP‑R6 Quick Start Guide

Removing the Port Cover

1. Press down and remove the port cover from the EdgePoint.

2. Depending on which cables will be connected, remove the

corresponding cable feed plugs from the port cover.

7

Hardware Installation

Grounding the EdgePoint

Note: The ground wire should be as short as possible and

no longer than one meter in length.

1. Remove the grounding screw and secure a ground wire (not
included) to the Ground Bonding Point.

2. Secure the other end of the ground wire to a grounded mast,
pole, tower, or grounding bar.

8

EdgePoint EP‑R6 Quick Start Guide

Connecting Ethernet

1. Connect the Ethernet cables to ports in this range: eth0‑eth4.

Note: PoE is disabled by default.

2. You can create a strain relief for any Ethernet cable by feeding
a cable tie (not included) through the tie slot under the cable.
Then wrap the cable tie around the cable and tighten.

3. Connect the other ends of the Ethernet cables to your

networkdevices.

9

Connecting Ethernet

Using the SFP Port (Optional)

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

To use an SFP port:

1. Plug a compatible fiber module into the SFP port.

2. Connect a fiber optic strand to the fiber module.

10

EdgePoint EP‑R6 Quick Start Guide

3. Create a strain relief by feeding a cable tie (not included)
through the tie slot under the cable. Then wrap the cable tie
around the cable and tighten.

11

Using the SFP Port (Optional)

Connecting to Power

Either the VDC input or PoE input is used at any one time. If both
input types are connected, only the input type with the highest
voltage will be used; the other can be used as a backup. Follow the
appropriate instructions for your installation:

Connecting to the 24VDC Input

1. Wire one end of the DC power cable to the VDC terminal block.

2. When you are finished, replace the port cover.
Optional: You can use an M4x6 set screw (not included) to

secure the port cover.

3. Wire the other end of the cable to a DC power supply. (Wiring
will depend on your device.)

4. Connect the DC power supply to its power source.

12

EdgePoint EP‑R6 Quick Start Guide

Connecting Power Using PoE

Note: Do NOT configure port eth0 in PoE output mode if you

are using it as a PoE input power source.

1. Connect an Ethernet cable to the PoE In / eth0 port of the
EdgePoint.

2. Connect the other end of the Ethernet cable to the POE port
on the Gigabit PoE adapter.

3. Connect an Ethernet cable from the LAN to the LAN port on
the Gigabit PoE adapter.

4. Connect the Power Cord to the Gigabit PoE adapter. Then plug
the Power Cord into a power outlet.

13

Connecting to Power

5. When you are finished, replace the port cover.
Optional: You can use an M4x6 set screw (not included) to

secure the port cover.

Mounting the Gigabit PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place the
bracket at the desired location, and mark the two holes.

2. Pre‑drill the holes if necessary, and secure the bracket using
two fasteners (not included).

3. Align the slots on the adapter with the tabs on the PoE
Mounting Bracket, and then slide the adapter down.

14

EdgePoint EP‑R6 Quick Start Guide

Accessing the EdgeOS® Configuration Interface

Note: Ensure that your host system is connected to the

Gigabit PoE adapter or local network of the EdgePoint.

1. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet.

2. Launch your web browser. Type https://192.168.1.1 in the
address field. Press enter (PC) or return (Mac).

3. The login screen will appear. Enter ubnt in the Username
and Password fields. Read the Ubiquiti License Agreement,
and check the box next to I agree to the terms of this License
Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you to
customize your settings as needed. You can click the Wizards tab
to access the Setup Wizard. For information on PoE configuration,
refer to the Configuring PoE Settings section.

15

Accessing the EdgeOS® Configuration Interface

Configuring PoE Settings

WARNING: Before activating 24V passive PoE, ensure

that the connected device supports PoE and the

suppliedvoltage.

1. Go to Actions > PoE for the interface you want to configure.

2. Select 24V from the PoE drop‑down menu.

Note: If the PoE screen states that PoE is not supported,

then there is insufficient power. You will need to increase
the power input to the EdgePoint.

3. ClickSave.

For more information, refer to the EdgeOS User Guide, which is
available at documentation.ubnt.com/edgemax

16

EdgePoint EP‑R6 Quick Start Guide

Specifications

EP‑R6

Dimensions 188.6 x 177.1 x 49.8 mm (7.43 x 6.97 x 1.96")
Weight 605 g (1.33 lb)
Max. Power Consumption 7W (Excludes PoE Output)
Power Input (1) DC Terminal Block or (1) RJ45 (eth0)

(Self‑Correcting Polarity Protection on DC

Terminal Block Only,

Diode ORed Protection on All Power Inputs)
Power Supply Min. 24V / 0.3A (Excludes PoE Output Power)
VDC Input 24V, 3A
Passive PoE Input (1) 24V / 1.4A, 4‑Pair (+1, 2, 4, 5; ‑3, 6, 7, 8)

Passive PoE, eth0

(Do NOT congure eth0 in PoE output mode

if you are using a PoE input power source.)

Passive PoE Output (5) 24V / 0.7A, 2‑Pair (+4, 5; ‑7, 8)

Passive PoE, eth0 to eth4

Power Monitoring (1) DC Terminal Block, Input Power

(1) RJ45, eth0, Input Power
Supported Voltage Range 26 to 16VDC
Button Reset
LEDs

System
eth0 to eth4
eth5/SFP

Power

Speed/Link/Activity, PoE

Speed/Link/Activity

Ports

Data Ports (5) 10/100/1000 RJ45 Ports

(1) 1 Gbps SFP Port

Processor Dual‑Core 880 MHz, MIPS1004Kc with

Hardware Acceleration for Packet Processing
System Memory 256 MB DDR3‑1600 RAM
Code Storage 256 MB NAND
Certications CE, FCC, IC
Pole/Wall Mount Yes
Operating Temperature ‑40 to 65° C (‑40 to 149° F)
Operating Humidity 10 ‑ 90% Noncondensing

17

Specifications

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can be

submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from
lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified may result in improper operation, damage to
the equipment or pose a fire hazard if the limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service should be
provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has an integral
safety ground wire intended for connection to a grounded safety outlet.

a. Do not substitute the power cord with one that is not the provided approved

type. Never use an adapter plug to connect to a 2‑wire outlet as this will
defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the safety

certification, modification or misuse can provide a shock hazard that can
result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there are questions

about the installation prior to connecting the equipment.

d. Protective earthing is provided by Listed AC adapter. Building installation

shall provide appropriate short‑circuit backup protection.

e. Protective bonding must be installed in accordance with local national wiring

rules and regulations.

18

EdgePoint EP‑R6 Quick Start Guide

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s)
furnished hereunder (the “Product(s)”) shall be free from defects in material and
workmanship for a period of one (1) year from the date of shipment by UBIQUITI
NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and
exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI
NETWORKS, at its discretion, to repair or replace any Product that fails to conform to
the above warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty period of
any repaired or replaced Product shall not extend beyond its original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto, except by

Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as
approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or accident;

(V) has been damaged or impaired as a result of using third party firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti

label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA.

In addition, the above warranty shall apply only if: the product has been properly
installed and used at all times in accordance, and in all material respects, with the
applicable Product documentation; all Ethernet cabling runs use CAT5 (or above),
and for outdoor installations, shielded Ethernet cabling is used, and for indoor
installations, indoor cabling requirements are followed.

Returns

No Products will be accepted for replacement or repair without obtaining a Return
Materials Authorization (RMA) number from UBIQUITI NETWORKS during the
warranty period, and the Products being received at UBIQUITI NETWORKS’ facility
freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products
returned without an RMA number will not be processed and will be returned freight
collect or subject to disposal. Information on the RMA process and obtaining an RMA
number can be found at: www.ubnt.com/support/warranty.

19

Limited Warranty

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS,
ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND
HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION
OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING,
BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF
MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A
PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY WARRANTIES ARISING
FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH
SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI
NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT
OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO
LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS
INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS
AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR
ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS,
CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the
operation of the Products will be error‑free or that operation will be uninterrupted.
In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any
nature or description relating to system performance, including coverage, buyer’s
selection of products (including the Products) for buyer’s application and/or failure of
products (including the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI
OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT,
LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE,
OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY,
CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied warranties
or conditions, so the above exclusion may not apply to you. You may have other
rights that vary from country to country, state to state, or province to province. Some
countries, states and provinces do not allow the exclusion or limitation of liability for
incidental or consequential damages, so the above limitation may not apply to you.
EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY
STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED
IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the
International Sale of Goods shall not apply to any transactions regarding the sale of
the Products.

20

EdgePoint EP‑R6 Quick Start Guide

Compliance

FCC

Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that
may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operations of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.

Industry Canada

CAN ICES‑3(A)/NMB‑3(A)

This Class A digital apparatus complies with Canadian CAN ICES‑003.

CAN ICES‑3(A)/NMB‑3(A)

Cet appareil numérique de la classe A est conforme à la norme NMB‑003 du Canada.

Australia and New Zealand

Warning: This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.

CE Marking

CE marking on this product represents the product is in compliance with all directives
that are applicable to it.

21

Compliance

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing this symbol on
the product and/or its packaging must not be disposed of with unsorted municipal
waste. The symbol indicates that this product should be disposed of separately from
regular household waste streams. It is your responsibility to dispose of this and other
electric and electronic equipment via designated collection facilities appointed by
the government or local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and human health. For more
detailed information about the disposal of your old equipment, please contact
your local authorities, waste disposal service, or the shop where you purchased the
product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die
direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist,
nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das
Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere
elektrische und elektronische Geräte über die dafür zuständigen und von der
Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative
Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere
Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die
örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei
dem Sie das Produkt erworben haben.

Español

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en
el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos
urbanos no seleccionados. El símbolo indica que el producto en cuestión debe
separarse de los residuos domésticos convencionales con vistas a su eliminación.
Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos
y electrónicos a través de los puntos de recogida que ponen a su disposición el
gobierno y las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias negativas para
el medio ambiente y la salud de las personas. Si desea obtener información más
detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades
locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la
tienda donde adquirió el producto.

22

EdgePoint EP‑R6 Quick Start Guide

Français

La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé
ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures
ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter
ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens
de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de
lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et
la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de
traitement des déchets, ou l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate
con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme
ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve
essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario
smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche
mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici
locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze
potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in
Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di
smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Declaration of Conformity

Česky
[Czech]

UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je
ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnice
1999/5/ES.

Dansk [Danish]

Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed,
er i overensstemmelse med de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.

Nederlands
[Dutch]

Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI NETWORKS apparaat,
in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EC.

English

Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is
in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.

Eesti [Estonian]

Käesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI NETWORKS
seade, on vastavus olulistele nõuetele ja teistele asjakohastele sätetele direktiivi
1999/5/EÜ.

Suomi [Finnish]

Täten UBIQUITI NETWORKS vakuuttaa, että tämä UBIQUITI NETWORKS laite, on
yhdenmukainen olennaisten vaatimusten ja muiden sitä koskevien direktiivin
1999/5/EY.

Français [French]

Par la présente UBIQUITI NETWORKS déclare que l’appareil UBIQUITI
NETWORKS, est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.

23

Declaration of Conformity

Deutsch
[German]

Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI NETWORKS
Gerät, in Übereinstimmung mit den grundlegenden Anforderungen und den
anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.

Ελληνική
[Greek]

Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI
NETWORKS, είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές
σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ.

Magyar
[Hungarian]

Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI NETWORKS készülék
megfelel az alapvető követelményeknek és más vonatkozó 1999/5/EK irányelv
rendelkezéseit.

Íslenska
[Icelandic]

Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI NETWORKS tæki er í
samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipun 1999/5/EC.

Italiano [Italian]

Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo
UBIQUITI NETWORKS, è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti della direttiva 1999/5/CE.

Latviski [Latvian]

Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS ierīce, ir saskaņā ar
būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvā 1999/5/EK.

Lietuviškai
[Lithuanian]

UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Malti
[Maltese]

Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS
huwa konformi mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta
‘Direttiva 1999/5/EC.

Norsk
[Norwegian]

Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enheten,
er i samsvar med de grunnleggende kravene og andre relevante bestemmelser
i direktiv 1999/5/EF.

Slovensky
[Slovak]

Týmto UBIQUITI NETWORKS, prehlasuje, že toto UBIQUITI NETWORKS
zariadenie, je v súlade so základnými požiadavkami a ďalšími relevantnými
ustanoveniami smernice 1999/5/ES.

Svenska
[Swedish]

Härmed UBIQUITI NETWORKS, intygar att denna UBIQUITI NETWORKS enhet
är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG.

Español
[Spanish]

Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo
UBIQUITI NETWORKS, cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Polski
[Polish]

Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie UBIQUITI NETWORKS,
jest zgodny z zasadniczymi wymaganiami oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.

Português
[Portuguese]

UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS,
está conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.

Română
[Romanian]

Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv UBIQUITI
NETWORKS este în conformitate cu cerințele esențiale și alte prevederi
relevante ale Directivei 1999/5/CE.

Online Resources

Support support.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com

JL012616

24

EdgePoint EP‑R6 Quick Start Guide

www.ubnt.com

© 2015‑2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks,
the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, EdgeMAX, EdgeOS, EdgePoint,
and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc. in
the United States and in other countries. All other trademarks are the property of their
respective owners.

*640-00224-04*

640-00224-04