Page 1
Lifting EyE kit (W4016701) instaLLation instRUCtions
Manual 0-5351
Revision No.: AA
Issue Date: June 6, 2014
16052 Swingley Ridge Road,
Suite 300 St, Louis, MO 63017
USA
www.victortechnologies.com
Lifting Eye Kit for
and VAF-4HD Wirefeeders
Part Number: W4016701
UltraFeed VAF-4
Assembly Instructions
General Information
The Tweco lifting eye kit (W4016701) is designed to be used together with UltraFeed VAF-4 and VAF-4HD Wirefeeders.
These instructions will guide you through the proper assembly procedure of the lifting eye kit.
Supplied Parts
The following components are included in this kit:
Description Quantity
Lifting Eye 1
Insulator Plate 1
Bolt, M8 × 40 (with torque 45~59 N.m.) 2
Flat Washer (smaller), M8 (with torque 45~59 N.m.) 2
Flat Washer (larger), M8 (with torque 45~59 N.m.) 2
Insulator Washer, M8 (with torque 45~59 N.m.) 2
Spring Washer, M8 (with torque 45~59 N.m.) 2
Nut, M8 (with torque 45~59 N.m.) 2
Table 1 Lifting Eye Kit
Manual 0-5351 Rev AA 1 ©2014 Victor Technologies International, Inc
Page 2
Lifting EyE kit (W4016701) instaLLation instRUCtions
!
!
Disconnect input power to the power source before installing or removing this control.
WARNING
SAFETY INSTRUCTIONS AND WARNINGS
WARNING
PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY.
PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS.
READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.
Welding products and welding processes can cause serious injury or death, or damage to other equipment or
property, if the operator does not strictly observe all safety rules and take precautionary actions.
Safe practices have developed from past experience in the use of welding and cutting. These practices must be
learned through study and training before using this equipment. Some of these practices apply to equipment connected to power lines; other practices apply to engine driven equipment. Anyone not having extensive training in
welding and cutting practices should not attempt to weld.
Safe practices are outlined in the American National Standard Z49.1 entitled: SAFETY IN WELDING AND CUTTING.
This publication and other guides to what you should learn before operating this equipment are listed at the end of
these safety precautions. HAVE ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR WORK PERFORMED
ONLY BY QUALIFIED PEOPLE.
WARNING
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
1. Do not touch live electrical parts.
2. Wear dry, hole-free insulating gloves and body protection.
3. Insulate yourself from work and ground using dry insulating mats or covers.
4. Disconnect input power or stop engine before installing or servicing this equipment. Lock input power disconnect switch open, or remove line fuses so power cannot be turned on accidentally.
5. Properly install and ground this equipment according to its Owner’s Manual and national, state, and local
codes.
6. Turn off all equipment when not in use. Disconnect power to equipment if it will be left unattended or out of
service.
7. Use fully insulated electrode holders. Never dip holder in water to cool it or lay it down on the ground or the
work surface. Do not touch holders connected to two welding machines at the same time or touch other people
with the holder or electrode.
8. Do not use worn, damaged, undersized, or poorly spliced cables.
©2014 Victor Technologies International, Inc 2 Manual 0-5351 Rev AA
Page 3
Lifting EyE kit (W4016701) instaLLation instRUCtions
9. Do not wrap cables around your body.
10. Ground the workpiece to a good electrical (earth) ground.
11. Do not touch electrode while in contact with the work (ground) circuit.
12. Use only well-maintained equipment. Repair or replace damaged parts at once.
13. In confined spaces or damp locations, do not use a welder with AC output unless it is equipped with a voltage
reducer. Use equipment with DC output.
14. Wear a safety harness to prevent falling if working above floor level.
15. Keep all panels and covers securely in place.
WARNING
ARC RAYS can burn eyes and skin; NOISE can damage hearing.
Arc rays from the welding process produce intense heat and strong ultraviolet rays that can burn eyes
and skin. Noise from some processes can damage hearing.
1. Use a Welding Helmet or Welding Faceshield fitted with a proper shade of filter (see ANSI Z49.1 and AS 1674
listed in Safety Standards) to protect your face and eyes when welding or watching.
2. Wear approved safety glasses. Side shields recommended.
3. Use protective screens or barriers to protect others from flash and glare; warn others not to watch the arc.
4. Wear protective clothing made from durable, flame-resistant material (wool and leather) and foot protection.
5. Use approved ear plugs or ear muffs if noise level is high.
6. Never wear contact lenses while welding.
WARNING
FUMES AND GASES can be hazardous to your health.
Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.
1. Keep your head out of the fumes. Do not breathe the fumes.
2. If inside, ventilate the area and/or use exhaust at the arc to remove welding fumes and gases.
3. If ventilation is poor, use an approved air-supplied respirator.
4. Read the Material Safety Data Sheets (MSDSs) and the manufacturer’s instruction for metals, consumables,
coatings, and cleaners.
5. Work in a confined space only if it is well ventilated, or while wearing an air-supplied respirator. Shielding gases
used for welding can displace air causing injury or death. Be sure the breathing air is safe.
6. Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can
react with vapours to form highly toxic and irritating gases.
7. Do not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed
from the weld area, the area is well ventilated, and if necessary, while wearing an air-supplied respirator. The
coatings and any metals containing these elements can give off toxic fumes if welded.
Manual 0-5351 Rev AA 3 ©2014 Victor Technologies International, Inc
Page 4
Lifting EyE kit (W4016701) instaLLation instRUCtions
WARNING
WELDING can cause fire or explosion.
Sparks and spatter fly off from the welding arc. The flying sparks and hot metal, weld spatter, hot workpiece, and hot equipment can cause fires and burns. Accidental contact of electrode or welding wire to
metal objects can cause sparks, overheating, or fire.
1. Protect yourself and others from flying sparks and hot metal.
2. Do not weld where flying sparks can strike flammable material.
3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with
approved covers.
4. Be alert that welding sparks and hot materials from welding can easily go through small cracks and openings to
adjacent areas.
5. Watch for fire, and keep a fire extinguisher nearby.
6. Be aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.
7. Do not weld on closed containers such as tanks or drums.
8. Connect work cable to the work as close to the welding area as practical to prevent welding current from travelling long, possibly unknown paths and causing electric shock and fire hazards.
9. Do not use welder to thaw frozen pipes.
10. Remove stick electrode from holder or cut off welding wire at contact tip when not in use.
WARNING
FLYING SPARKS AND HOT METAL can cause injury.
Chipping and grinding cause flying metal. As welds cool, they can throw off slag.
1. Wear approved face shield or safety goggles. Side shields recommended.
2. Wear proper body protection to protect skin.
WARNING
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas
cylinders are normally part of the welding process, be sure to treat them carefully.
1. Protect compressed gas cylinders from excessive heat, mechanical shocks, and arcs.
2. Install and secure cylinders in an upright position by chaining them to a stationary support or equipment cylinder rack to prevent falling or tipping.
3. Keep cylinders away from any welding or other electrical circuits.
4. Never allow a welding electrode to touch any cylinder.
5. Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application;
maintain them and associated parts in good condition.
6. Turn face away from valve outlet when opening cylinder valve.
©2014 Victor Technologies International, Inc 4 Manual 0-5351 Rev AA
Page 5
Lifting EyE kit (W4016701) instaLLation instRUCtions
7. Keep protective cap in place over valve except when cylinder is in use or connected for use.
8. Read and follow instructions on compressed gas cylinders, associated equipment, and CGA publication P-1
listed in Safety Standards.
WARNING
MOVING PARTS can cause injury.
Moving parts, such as fans, rotors, and belts can cut fingers and hands and catch loose clothing.
1. Keep all doors, panels, covers, and guards closed and securely in place.
2. Stop engine before installing or connecting unit.
3. Have only qualified people remove guards or covers for maintenance and troubleshooting as necessary.
4. To prevent accidental starting during servicing, disconnect negative (-) battery cable from battery.
5. Keep hands, hair, loose clothing, and tools away from moving parts.
6. Reinstall panels or guards and close doors when servicing is finished and before starting engine.
Manual 0-5351 Rev AA 5 ©2014 Victor Technologies International, Inc
Page 6
Lifting EyE kit (W4016701) instaLLation instRUCtions
!
This product, when used for welding or cutting, produces fumes or gases which contain chemicals
know to the State of California to cause birth defects and, in some cases, cancer. (California Health &
Safety code Sec. 25249.5 et seq.)
Considerations About Welding And The Effects of Low Frequency Electric and Magnetic Fields
The following is a quotation from the General Conclusions Section of the U.S. Congress, Office of Technology Assessment, Biological Effects of Power
Frequency Electric & Magnetic Fields - Background Paper, OTA-BP-E-63 (Washington, DC: U.S. Government
Printing Office, May 1989): “...there is now a very large volume of scientific findings based on experiments at the
cellular level and from studies with animals and people which clearly establish that low frequency magnetic fields
and interact with, and produce changes in, biological systems. While most of this work is of very high quality, the
results are complex. Current scientific understanding does not yet allow us to interpret the evidence in a single
coherent framework. Even more frustrating, it does not yet allow us to draw definite conclusions about questions
of possible risk or to offer clear science-based advice on strategies to minimize or avoid potential risks.”
To reduce magnetic fields in the workplace, use the following procedures.
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cable around the body.
WARNING
NOTE
4. Keep welding power source and cables as far away from body as practical.
ABOUT PACEMAKERS:
The above procedures are among those also normally recommended for pacemaker wearers. Consult
your doctor for complete information.
©2014 Victor Technologies International, Inc 6 Manual 0-5351 Rev AA
Page 7
Lifting EyE kit (W4016701) instaLLation instRUCtions
AWS F2.2:2001 (R2010), Adapted with permission of the American Welding Society (AWS), Miami, Florida
Guide for Shade Numbers
Minimum
Protective
Shade
7
8
10
11
Process
Shielded Metal Arc Welding
(SMAW)
Electrode Size in.
(mm)
Less than 3/32 (2.4)
3/32-5/32 (2.4-4.0)
5/32-1/4 (4.0-6.4)
More than 1/4 (6.4)
Arc Current
(Amperes)
Less than 60
60-160
160-250
250-550
Suggested*
Shade No.
(Comfort)
10
12
14
Gas Metal Arc Welding (GMAW)
and Flux Cored Arc Welding
(FCAW)
Gas Tungsten arc Welding
(GTAW)
Air Carbon Arc Cutting (CAC-A)
Plasma Arc Welding (PAW)
Plasma Arc Cutting (PAC)
* As a rule of thumb, start with a shade that is too dark to see the weld zone. Then go to a lighter
shade which gives sufficient view of the weld zone without going below the minimum. In oxyfuel gas
welding, cutting, or brazing where the torch and/or the flux produces a high yellow light, it is desirable
to use a filter lens that absorbs the yellow or sodium line of the visible light spectrum.
(Light)
(Heavy)
Less than 60
60-160
160-250
250-550
Less than 50
50-150
150-500
Less than
500
500-1000
Less than 20
20-100
100-400
400-800
Less than 20
20-40
40-60
60-80
80-300
300-400
400-800
7
10
10
10
8
8
10
10
11
6
8
10
11
4
5
6
8
8
9
10
11
12
14
10
12
14
12
14
6 to 8
10
12
14
4
5
6
8
9
12
14
Manual 0-5351 Rev AA 7 ©2014 Victor Technologies International, Inc
Page 8
Lifting EyE kit (W4016701) instaLLation instRUCtions
Handle Assembly
Flat Washer
!
Assembly Procedure
1. Loosen the M10 x 50 Bolts, M10 Flat Washers, M10 Spring Washers and M10 Nuts with 17mm wrench that
secure the handle assembly and remove the handle assembly and fixings from the base assembly.
Bolt, M10 × 50
Flat Washer, M10
Spring Washer, M10
Nut, M10
Art # A-12471
Figure 1 Removing Handle Assembly
2. Use 14mm wrench to secure the lifting eye and insulator plate to the base assembly using the M8 x 40 Bolts,
M8 Flat Washers, M8 insulator washers, M8 Spring Washers and M8 Nuts as supplied with this kit.
Bolt, M8 × 40
(smaller), M8
Art # A-12473
Figure 2 Installing Lifting Eye Kit
Fully tighten all the fasteners with torque 45~59 N.m.
Refer to the figure below for the assembled lifting eye kit.
Lifting Eye
Insulator Plate
Insulator Washer, M8
Flat Washer (larger), M8
Spring Washer, M8
Nut, M8
WARNING
Lifting Eye
Art # A-12474
Figure 3 Assembled Lifting Eye Kit
©2014 Victor Technologies International, Inc 8 Manual 0-5351 Rev AA
Loading...