Trimble GeoExplorer 6000 series User Manual

Download

User GUide

GeoExplorer® 6000 series

Version 1.00 Revision A February 2011

USER GUIDE

GeoExplorer

6000 series

4 GeoExplorer 6000 Series User Guide

Trimble Navigation Limited 10355 Westmoor Drive Suite #100 Westminster, CO 80021 USA

www.trimble.com

Legal Notices

trademarks of Trimble Navigation Limited, registered in the United States and in other countries. EVEREST, GeoBeacon, GeoXH, GeoXT, GPS Analyst, GPScorrect, H-Star, Floodlight, Tempest, TerraSync, Tornado, and VRS are trademarks of Trimble Navigation Limited.

Microsoft, ActiveSync, Excel, OneNote, Outlook, PowerPoint, Windows, Windows Live, Windows Media, Windows Mobile, Windows Vista, and the Windows Start logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Trimble Navigation Limited is under license.

All other trademarks are the property of their respective owners.

Release Notice

This is the February 2011 release (Revision A) of the GeoExplorer 6000 Series User Guide. The GeoExplorer 6000 series handheld’s operating

system is based on the Microsoft Windows Mobile version 6.5 operating system.

Limited Warranty Terms and Conditions

Product Limited Warranty

Subject to the terms and conditions set forth herein, Trimble Navigation Limited (“Trimble”) warrants that for a period of (1) year from date of purchase this Trimble product (the “Product”) will substantially conform to Trimble's publicly available specifications for the Product and that the hardware and any storage media components of the Product will be substantially free from defects in materials and workmanship.

Product Software

Product software, whether built into hardware circuitry as firmware, provided as a standalone computer software product, embedded in flash memory, or stored on magnetic or other media, is licensed solely for use with or as an integral part of the Product and is not sold. The terms of the end user license agreement, as included below, govern the use of the Product Software, including any differing limited warranty terms, exclusions and limitations, which shall control over the terms and conditions set forth in the limited Product warranty.

Warranty Remedies

If the Trimble Product fails during the warranty period for reasons covered by this limited warranty and you notify Trimble of such failure during the warranty period, Trimble will repair OR replace the nonconforming Product with new, equivalent to new, or reconditioned parts or Product, OR refund the Product purchase price paid by you, at Trimble’s option, upon your return of the Product in accordance with Trimble's product return procedures then in effect.

How to Obtain Warranty Service

To obtain warranty service for the Product, please contact your Trimble dealer. Alternatively, you may contact Trimble to request warranty service at +1-408-481-6940 (24 hours a day) or email your request to

trimble_support@trimble.com. Please be prepared to provide:

– your name, address, and telephone numbers; – proof of purchase; – a copy of this Trimble warranty – a description of the nonconforming Product including the model

number; and

– an explanation of the problem. The customer service representative may need additional information

from you depending on the nature of the problem.

Warranty Exclusions and Disclaimer

This Product limited warranty shall only apply in the event and to the extent that (i) the Product is properly and correctly installed, configured, interfaced, maintained, stored, and operated in accordance with Trimble's applicable operator's manual and specifications, and; (ii) the Product is not modified or misused. This Product limited warranty shall not apply to, and Trimble shall not be responsible for, defects or performance problems resulting from (i) the combination or utilization of the Product with hardware or software products, information, data, systems, interfaces, or devices not made, supplied, or specified by

Trimble; (ii) the operation of the Product under any specification other than, or in addition to, Trimble's standard specifications for its products; (iii) the unauthorized installation, modification, or use of the Product; (iv) damage caused by: accident, lightning or other electrical discharge, fresh or salt water immersion or spray (outside of Product specifications); or exposure to environmental conditions for which the Product is not intended; (v) normal wear and tear on consumable parts (e.g., batteries); or (vi) cosmetic damage. Trimble does not warrant or guarantee the results obtained through the use of the Product or Software, or that software components will operate error free.

NOTICE REGARDING PRODU CTS EQUIPPED WITH TECHNOLOGY CAPABLE OF TRACKING SATELLITE SI GNALS FROM SATELLITE BASED AUGMENTATION SYSTEM S (SBAS) (WAAS, EGNOS, AND MSAS), OMNISTAR, GPS, MODERNIZED GPS OR GLONASS SATELLITES, OR FROM IALA BEACON SOURCES: TRIMBLE IS NOT RESPONSI BLE FOR THE OPERATION OR FAILURE OF OPERATION OF ANY SATELLITE BASED POSITIONING SYSTEM OR THE AVAI LABILITY OF ANY SATELLITE BASED POSITIONING SIGNALS.

THE FOREGOING LIMITED WARRANTY TERMS STATE TRIMBL E’S ENTIRE LIABILITY, AND YOUR EXCLUSIVE REMEDIES, RE LATING TO THE TRIMBLE PRODUCT. EXCEPT AS OTHERWISE EXPRESSLY PROVIDED HEREIN, THE PRODUCT, AND ACCOMPANYING DOCUMENTATION AND MATERIALS ARE PROVIDED “AS-IS” AND WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY KIND, BY EITHER TRIMBLE OR ANYONE WHO HAS BEEN INVOLVED IN ITS CREATION, PRODUCTION, INSTALLATION, OR DISTRIBUTION , INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NONINFRINGEMENT. THE ST ATED EXPRESS WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART OF TRIMBLE ARISING OUT OF, OR IN CONNECTION WITH, ANY PRODUCT. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED WARRANTY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

Limitation of Liability

TRIMBLE'S ENTIRE LIABILITY UNDER ANY PROVISION HEREIN SHALL BE LIMITED TO THE AMOU NT PAID BY YOU FOR THE PRODUCT. TO TH E MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INC IDENTAL, OR CONSEQUENTIAL DAMAGE WHATSOEVER UNDER ANY CIRCUMSTANCE OR LEGAL THEORY RELATIN G IN ANYWAY TO THE PRODUCTS, SOFTWARE AND ACCOMPANYING DOCUMENTATION AND MATERIALS, (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA, OR ANY OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER TRIMBLE HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLE SS OF THE COURSE OF DEALING WHICH DEVELOPS OR HAS DEVELOPED BETWEEN YOU AND TRIMBLE . BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

PLEASE NOTE: THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS WILL NOT APPLY TO PRODUCTS PURCHASED IN THOSE JURISDICTIONS (E.G., MEMBER STATES OF THE EUROPEAN ECONOMIC

AREA) IN WHICH PRODUCT WARRANTIES ARE THE RESPONSI BILITY

OF THE LOCAL DEALER FROM WHOM THE PRODUCTS ARE ACQUIRED. IN SUCH A CASE, PLEASE CONTACT YOUR TRIMBLE DEALER FOR APPLICABLE WARRANTY INFORMATION.

Official Language

THE OFFICIAL LANGUAGE OF THESE TERMS AND CONDITIONS IS ENGLISH. IN THE EVENT OF A CONFLICT BETWEEN ENGLISH AND OTHER LANGUAGE VERSIONS, THE ENGLISH LANGUAGE SHALL CONTROL.

End User License Agreement for Product Software

IMPORTANT, READ CAREFULLY. THIS END USER LICENSE AGREEMENT (“EULA”) IS A LEGAL AGREEMENT BETWEEN YOU AND Trimble Navigation Limited (“Trimble”) and applies to the computer software provided with the Trimble product purcha sed by you (whether built into hardware circuitry as firmware, embedded in flash memory or a PCMCIA card, or stored on magnetic or other media), or provided as a stand-alone computer software product, and includes any accompanying written materials such as a user's guide or product manual, as well as any "online" or electronic documentation ("Software" or “Product Software”). This EULA will also apply to any Software error corrections, updates and upgrades subsequently furnished by Trimble, unless such are accompanied by different license terms and conditions, which will govern their use. You have acquired a Trimble Product ("Device") that includes Software, some of which was licensed by Trimble from Microsoft Corporation or its affiliates (collectively "Microsoft"). The Software licensed from Microsoft, as well as associated updates, supplements, internet-based services and support services, media, printed materials, and "online" or electronic documentation ("Microsoft Software"), are protected under this EULA. The Software is

GeoExplorer 6000 Series User Guide 5

also protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The Software is licensed, not sold.

BY USING THE SOFTWARE, INCLUDING USE ON THIS DEVICE, YOU ACCEPT THESE TERMS. IF YOU DO NOT ACCEPT THEM, DO NOT USE THE DEVICE OR SOFT WARE. INSTEAD CONTACT TRIMBLE FOR A REFUND OR CREDIT. As described below, using some features also operates as your consent to the transmission of certain standard computer information for Internet-based services.

WAR NI NG : If the Software contains voice operated technologies, then operating this Software requires user attention. Diverting attention away from the road while driving can possibly cause an accident or other serious consequence. Even occasional, short diversions of attention can be dangerous if your attention is diverted away from your driving task at a critical time. Trimble and Microsoft make no representations, warranties or other determinations that ANY use of this Software is legal, safe, or in any manner recommended or intended while driving or otherwise operating a motor vehicle.

This EULA does not grant you any rights with respect to the Windows Mobile Device Center, Microsoft ActiveSync or Microsoft Outlook 2007 Trial which are subject to the licenses accompanying those items.

1 SOFTWARE PRODUCT LICENSE

1.1 License Grant

. Subject to the terms and conditions of this EULA, Trimble grants you a non-exclusive right to use one copy of the Software in a machine-readable form only as installed on the Device. Such use is limited to use with the Device for which it was intended, as set forth in the product documentation. The Device Software is licensed with the Device as a single integrated product. The Device Software installed in read only m emory (“ROM ”) of the Devi ce may only be u sed as part of the Device into which it was embedded. You may use the installation Software from a computer solely to download the Software to one Device. In no event shall the installation Software be used to download the Software onto more than one Device. A license for the Software may not be shared or used concurrently on different computers or Devices.

1.2 Scope of License

. This EULA only gives you some rights to use the Software. Trimble and Microsoft reserve all other rights. Unless applicable law gives you more rights despite this limitation, y ou may use the Software only as expressly permitted in this EULA. In doing so, you must comply with any technical limitations in the Software that allow you to use it only in certain ways. Except as expressly provided in this EULA, rights to access the Software on this Device do not give you any right to implement Microsoft patents or other Microsoft intellectual property in software or devices that access this device. You may use remote access technologies in the software such as Remote Desktop Mobile to access the Software remotely from a computer or server. You are responsible for obtaining any licenses required for use of the protocols to access other software.

1.3 Proof of License. If you acquired the Software on the Device, or on a disc or other media, a genuine Certificate of Authenticity label with a genuine copy of the Software identifies licensed software. To be valid, this label must be affixed to the Device, or included on or in the software packaging. If you receive the label separately, it is not valid. You should keep the label on the device or packaging to prove that you are licensed to use the Software. To identify genuine Microsoft Software, see

http://www.howtotell.com.

1.4 Connectivity Software

. Your Device package may include Windows Mobile Device Center or Microsoft ActiveSync software. If it is included, then you may install and use it in accordance with the license terms that are provided with it. If no license terms are provided, then you may install and use only one (1) copy of the Software on a single computer.

1.5 Digital Certificates. The Software uses digital certificates in X.509 format. These digital certificates are used for authentication.

1.6 Phone Functionality. If the Device Software includes phone functionality, all or certain portions of the Device Software may be inoperable if you do not have and maintain a service account with a wireless telecommunication carrier (“Mobile Operator”), or if the Mobile Operator’s network is not operating or configured to operate with the Device.

1.7 Upgrade Software

. In the event that any upgrades to the Software, including Microsoft Software, are provided under this EULA, then the following shall apply : you may follow the applicable instructions accompanying this Software and install one (1) copy of the Software on one (1) Device presently containing a licensed copy of a predecessor version of the Software (unless this EULA indicates that this Software copy has been licensed for installation on multiple Devices). NO REPRESENTATION OR WARRANTY IS MADE BY TRIMBLE OR MICROSOFT WITH RESPECT TO THE COMPATIBILITY OF THIS SOFTWARE WITH ANY DEVICE OR ANY OTHER EXISTING SO FTWAR E OR D ATA OF A NY KI ND CO NTAI NED O N SUC H DEV ICES , AND NEITHER TRIMBLE OR MICROSOFT SHALL BE RESPONSIBLE IN ANY REGARD WITH RESPECT TO ANY LOSS, CORRUPTION,

MODIFICATION OR INACCESSIBILITY OF ANY DATA, APPLICATIONS OR OTHER SOFTWARE RESULTING FROM THE INSTALLATION OF THE SOFTWARE ON ANY DEVICE.

1.8 Internet-Based Services Components. Microsoft provides Internetbased services with the software. Microsoft may change or cancel them at any time. The Microsoft Software features described below connect to Microsoft or service provider computer systems over the Internet. In some cases, you will not receive a separate notice when they connect. You may switch off some of these features or not use them. For more information about these features, visit

http://go.microsoft.com/fwlink/?LinkId=81931. By using these

features, you consent to the transmission of this information. Microsoft does not use the information to identify or contact you. You may not use these services in any way that could harm them or impair anyone else’s use of them. You may not use the services to try to gain unauthorized access to any service, data, account or network by any means.

1.9 Device Information. The following features use Internet protocols, which send to the appropriate systems device information, such as your Internet protocol address, the type of operating system, browser and name and version of the Software you are using, and the language code of the Device where you installed the Software. Microsoft uses this information to make the Internet-based services available to you. a) Update Features: Windows Mobile Update feature provides you the ability to obtain and install Software updates on your Device if updates are available. You may choose not to use this feature. Trimble and/or your Mobile Operator may not support this feature or an update for your device. b) Security Updates/Digital Rights Management. Content owners use Windows Media digital rights management technology (WMDRM) to protect their intellectual property, including copyrights. This software and third party software use WMDRM to play and copy WMDRM-protected content. If the software fails to protect the content, content owners may ask Microsoft to revoke the software's ability to use WMDRM to play or copy protected content. Revocation does not affect other content. When you download licenses for protected content, you agree that Microsoft may include a revocation list with the licenses. Content owners may require you to upgrade WMDRM to access their content. Microsoft software that includes WMDRM will ask for your consent prior to the upgrade. If you decline an upgrade, you will not be able to access content that requires the upgrade.

1.10 Additional Software/Services. The Device Software may permit Trimble, Microsoft, their affiliates and/or their designated agent to provide or make available to you Software updates, supplements, add-on components, or Internet-based services components of the Software after the date you obtain your initial copy of the Software (“Supplemental Components”).

1.10.1 If Trimble provides or makes available to you Supplemental Components and no other end user license agreement terms are provided along with the Supplemental Components, then the terms of this EULA shall apply.

1.10.2 If Microsoft, its affiliates and/or its designated agent makes available Supplemental Components, and no other end user license agreement terms are provided, then the terms of this EULA shall apply, except that the Microsoft entity or affiliate entity providing the Supplemental Component(s) shall be the licensor of the Supplemental Component(s).

1.10.3 Trimble, Microsoft and each of their affiliates and/or their designated agents reser ve the right to discontinue any Internetbased services provided to you or made available to you through the use of the Device Software.

1.11 Links to Third Party Sites

. If the Software provides links to third party websites, those links are provided to you only as a convenience, and the inclusion of any link does not imply an endorsement of the third party website by Microsoft or Trimble.

1.12 Other Rights and Limitations. (1) The Software contains valuable trade secrets proprietary to Trimble and its suppliers. To the extent permitted by relevant law, you shall not, nor allow any third party to copy, decompile, disassemble or otherwise reverse engineer the Software, or attempt to do so, provided, however, that to the extent any applicable mandatory laws (such as, for example, national laws implementing EC Directive 91/250 on the Legal Protection of Computer Programs) give you the right to perform any of the aforementioned activities without Trimble's consent in order to gain certain information about the Software for purposes specified in the respective statutes (i.e., interoperability), you hereby agree that, before exercising any such rights, you shall first request such information from Trimble in writing detailing the purpose for which you need the information. Only if and after Trimble, at its sole discretion, partly or completely denies your request, may you exercise such statutory rights. (2) This Software is licensed as a single product. You may not separate its component parts for use on more than one computer nor make more copies of the software than specified in this EULA. (3) You may not rent, lease, or lend the Software. (4) No service bureau work, multiple-user license or timesharing arrangement is permitted. For purposes of this EULA “service

6 GeoExplorer 6000 Series User Guide

bureau work” shall be deemed to include, without limitation, use of the Software to process or to generate output data for the benefit of, or for purposes of rendering services to any third party over the Internet or other communications network. (5) You may make one backup copy of the Software. You may use it only to reinstall the Software on the Device. (6) You may transfer the Software only with the Device, the Certificate of Authenticity label, and these license terms directly to a third party. Before the transfer, that party must agree that these license terms apply to the transfer and use of the Software. You may not retain any copies of the Software including the backup copy. (7) The Software is subject to United States export laws and regulations. You must comply with all domestic and international export laws and regulations that apply to the Software. These laws include restrictions on destinations, end users, and end use. For additional information see

http://www.microsoft.com/exporting. (8) Without prejudice as to any

other rights, Trimble may terminate this EULA without notice if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the Software and all of its component parts. (9) If the Microsoft Software includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process. Neither Trimble, Microsoft, nor any of their suppliers shall be liable for any damages arising out of errors in the speech recognition process. (10) You may not publish the Software for others to copy. (11) You may not use the Software for commercial software hosting services.

1.13 Notice Regarding the MPEG-4 Visual Standard

. The Software may include MPEG-4 visual decoding technology. This technology is a format for data compression of video information. MPEG LA, L.L.C. requires this notice: USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE DIRECTLY RELATED TO (A) DATA OR INFORMATION (i) GENERATED BY AND OBTAINED WITHOUT CHARGE FROM A CONSUMER NOT THEREBY ENGAGED IN A BUSINESS ENTERPRISE, AND (ii) FOR PERSONAL USE ONLY; AND (B) OTHER USES SPECIFICALLY AND SEPARATELY LICENSED BY MPEG LA, L.L.C. If you have questions about the MPEG-4 visual standard, please contact MPEG LA, L.L.C., 250 Steele Street, Suite 300, Denver, CO 80206; www.mpegla.com.

1.14 If the Device Software is provided by Trimble separate from the Device on media such as a ROM chip, CD ROM disk(s) or via web download or other means, and is labeled “For Upgrade Purposes Only” you may install one (1) copy of such Device Software onto the Device as a replacement copy for the existing Device Software and use it accordance with this EULA, including any additional end user license agreement terms accompanying the upgrade Device Software.

1.15 If any software component(s) is provided by Trimble separate from the Device on CD ROM disc(s) or via web download or other means, and labeled “For Upgrade Purposes Only,” you may (i) install and use one (1) copy of such component(s) on the computer(s) you use to exchange data with the Device as a replacement copy for the existing Companion CD com pone nt(s).

1.16 Copyright

. All title and copyrights in and to the Software (including but not limited to any images, photographs, animations, video, audio, music, text and “applets,” incorporated into the Software), the accompanying printed materials, and any copies of the Software are owned by Trimble, or Microsoft (including Microsoft Corporation), and their respective suppliers. You may not copy the printed materials accompanying the Software. All title and intellectual property rights in and to the content which may be a ccessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such content. You shall not remove, cover or alter any of Trimble’s patent, copyright or trademark notices placed upon, embedded in or displayed by the Software or on its packaging and related materials. All rights not specifically granted in this EULA are reserved by Trimble, Microsoft, and their respective suppliers.

1.17 U.S. Government Restricted Rights

. The Software is provided with “RESTRICTED RIGHTS”. Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in this EULA, and as provided in DFARS 227.7202-1(a) and 227.7202-3(a) (1995), DFARS 252.227-7013(c)(1)(ii) (OCT 1988), FAR 12.212(a) (1995), FAR

52.227-19, or FAR 52.227-14(ALT III), as applicable.

1.18 Microsoft has contractually obligated Trimble to include the following terms in this EULA:

Product Support

. The Product support for the Software is not provided by Microsoft or its affiliates or subsidiaries. For product support, please refer to the Trimble support numb er provided in the documentation for the Device.

Not fault tolerant

. The Software is not fault tolerant. Trimble installed the Software on the Device and is responsible for how it operates on the Device.

Restricted user

. The Microsoft Software was designed for systems that do not require fail-safe performance. You may not use the Microsoft Software in any device or system in which a malfunction of the Microsoft Software would result in foreseeable risk of injury or death to any person. This includes operation of nuclear facilities, aircraft navigation or communication systems and air traffic control.

No warranties for the software. Microsoft gives no express warranties, guarantees or conditions regarding the Microsoft Software. Any warranties you receive regarding the Device or the Software do not originate from, and are not binding on, Microsoft or its affiliates. When allowed by your local laws, Trimble and Microsoft exclude implied warranties of merchantability, fitness for a particular purpose and non-infringement.

LIABILITY LIMITATIONS. You can recover from Microsoft and its affiliates only direct damages up to fifty U.S. Dollars (U.S. $50.00), or equivalent in local currency. You cannot recover any other damages, including consequential, lost profits, special, indirect or incidental damages. This limitation applies to:

– Anything related to the Software, services, content

(including code) on third party internet sites, or third party programs, and

– claims for breach of contract, breach of warranty, guarantee

or condition, strict liability, negligence, or other tort to the extent permitted by applicable law.

It also applies even if Microsoft should have been aware of the possibility of the damages. The above limitation may not apply to you because your country may not allow the exclusion or limitation of incidental, consequential or other damages.

2 LIMITED WARRANTY FOR TRIMBLE PRODUCT SOFTWARE.

2.1 Limited Warranty. Trimble warrants that the Software, exclusive of the Microsoft Software, will perform substantially in accordance with the accompanying written materials for a period of twelve (12) months from the date of purchase. This limited warranty gives you specific legal rights; you may have others, which vary from state/jurisdiction to state/jurisdiction. The above limited warranty does not apply to Fixes, Minor Updates, or Major Upgrades of the Software after expiration of the twelve (12) month limited warranty period , all of which are provided “AS IS” and without warranty unless otherwise specified in writing by Trimble. Because the Software is inherently complex and may not be completely free of nonconformities, defects or errors, you are advised to verify your work. Trimble does not warrant that the Software will operate error free or uninterrupted, will meet your needs or expectations, or that all nonconformities can or will be corrected.

2.2 Software Fixes. During the limited warranty period described in section 2.1 above, you will be entitled to receive such Fixes to the Product Software that Trimble releases and makes commercially available and for which it does not charge separately, subject to the procedures for delivery to purchasers of Trimble products generally. If you have purchased the Product from an authorized Trimble dealer rather than from Trimble directly, Trimble may, at its option, forward the software Fix to the Trimble dealer for final distribution to you. Minor Updates, Major Upgrades, new products, or substantially new software releases, as identified by Trimble, are expressly excluded from this update process and limited warranty. Receipt of Software Fixes or other enhancements shall not serve to extend the limited warranty period.

For purposes of this warranty the following definitions shall apply: (1) "Fix(es)" means an error correction or other update created to fix a previous software version that does not substantially conform to its Trimble specifications; (2) "Minor Update" occurs when enhancements are made to current features in a software program; and (3) "Major Upgrade" occurs when significant new features are added to software, or when a new product containing new features replaces the further development of a current product line. Trimble reserves the right to determine, in its sole discretion, what constitutes a Fix, Minor Update, or Major Upgrade.

2.3 Customer Remedies. Trimble’s and its suppliers’ entire liability, and your sole remedy, with respect to the Software shall be either, at Trimble’s option, (a) repair or replacement of the Software, or (b) return of the license fee paid for any Software that does not meet Trimble’s limited warranty. This limited warranty is void if failure of the Software has resulted from (1) accident, misuse, abuse, or misapplication; (2) alteration or modification of the Software without Trimble’s authorization; (3) interaction with software or hardware not supplied or supported by Trimble; (4) your improper, inadequate or unauthorized installation, maintenance or storage; or (5) if you violate the terms of this EULA. Any replacement Software will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer.

2.4 NO OTHER WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, TRIMBLE AND ITS SUPPLIERS DISCLAIM ALL OTHER WARRANTIES, TERMS AND CONDITIONS, EITHER EXPRESS OR IMPLIED, BY STATUTE, COMMON LAW OR

GeoExplorer 6000 Series User Guide 7

OTHERWISE, INCLUDING BUT NOT LIMITED TO, IMPLIED WARRANTIES, TERMS AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NONINFRINGEMENT WITH REGARD TO THE SOFTWARE, ITS SATISFACTORY QUALITY AND THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES. TO THE EXTENT ALLOWED BY APPLICABLE LAW, IMPLIED WARRANTIES, TERMS AND CONDITIONS ON THE SOFTWARE ARE LIMITED TO NINETY (90) DAYS. Y0U MAY HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE/JURISDICTION TO STATE/JURISDICTION.

NO WARRANTIES FOR THE MICROSOFT SOFTWARE. THE MICROSOFT SOFTWARE is provided “AS IS” and with all faults, AND TRIMBLE PROVIDES NO WARRANTY WITH RESPECT THERETO. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY AND EFFORT (INCLUDING LACK OF NEGLIGENCE) FOR THE MICROSOFT SOFTWARE IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE MICROSOFT SOFTWARE OR AGAINST INFRINGEMENT.

2.5 PLEASE NOTE: THE FOREGOING TRIMBLE LIMITED WARRANTY PROVISIONS MAY NOT APPLY TO SOFTWARE PRODUCT LICENSES PURCHASED IN THOSE JURISDICTIONS (SUCH AS COUNTRIES OF THE EUROPEAN UNION) IN WHICH PRODUCT WARRANTIES ARE O BTAINED FROM THE LOCAL DISTRIBUTOR. IN SUCH CASES, PLEASE CONTACT YOUR TRIMB LE DEALER FOR APPLI CABLE WARRANTY INF ORMATION.

3 TRIMBLE LIMITATION OF LIABILITY

3.1 LIMITATION OF LIABILITY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENTIAL OR PUNITIVE DAMAGES HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE, OR THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES, EVEN IF TRIMBLE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY EXCLUSIVE REMEDY PROVIDED IN THIS EULA.

IN NO EVENT SHALL THE TOTAL CUMULATIVE LIABILITY OF TRIMBLE AND ITS SUPPLIERS IN CONNECTION WITH THIS EULA OR THE SOFTWARE, WHETHER BASED ON CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, EXCEED THE ACTUAL AMOUNT PAID TO TRIMBLE FOR THE SOFTWARE LICENSE GIVING RISE TO THE CLAIM. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

4 GENERAL.

4.1 This EULA shall be governed by the laws of the State of California and applicable United States Federal law without reference to “conflict of laws” principles or provisions. The United Nations Convention on Contracts for the International Sale of Goods will not apply to this EULA. Jurisdiction and venue of any dispute or court action arising from or related to this EULA or the Software shall lie exclusively in or be transferred to the courts the County of Santa Clara, California, and/or the United States District Court for the Northern District of California. You hereby consent and agree not to contest, such jurisdiction, venue and governing law.

4.2 Section 4.1 notwithstanding, if you acquired this product in Canada, this EULA is governed by the laws of the Province of Ontario, Canada. In such case each of the parties to this EULA irrevocably attorns to the jurisdiction of the courts of the Province of Ontario and further agrees to commence any litigation that may arise under this EULA in the courts located in the Judicial District of York, Province of Ontario. If you acquired this product in the European Union, this EULA is governed by the laws of The Netherlands, excluding its rules governing conflicts of laws and excluding the United Nations Convention on the International Sale of Goods. In such case each of the parties to this EULA irrevocably attorns to the jurisdiction of the courts of The Netherlands and further agrees to commence any litigation that may arise under this EULA in the courts of The Hague, The Netherlands.

4.3 Trimble reserves all rights not expressly granted by this EULA.

4.4 Official Language. The official language of this EULA and of any documents relating thereto is English. For purposes of interpretation, or in the event of a conflict between English and versions of this EULA or related documents in any other language, the English language version shall be controlling.

Registration

To receive information regarding updates and new products, please contact your local dealer or visit the Trimble website at

www.trimble.com/register. Upon registration you may select the

newsletter, upgrade, or new product information you desire.

Notices

Class B statement- Notice to users This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must acc ept any interference received, including inter ference that may cause undesired operation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communication.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and the receiver. – Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer

or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules.

The radios in this device have been designed and manufactured to not exceed stipulated emission limits for exposure to radio frequency (RF) energy as required by the Federal Communications Commission of the U.S. Government 47 C.F.R. § 2.1091 and 2.1093.

The FCC limits for Specific Absorption Rate (SAR) for general population / uncontrolled exposure for partial-body and extremities such as hands/wrists/feet and ankles are 1.6W/kg and 4W/kg respectively.

The greatest recorded FCC 10-g SAR value as determined at the highest certified power level of this device measured adjacent to the antenna was measured at 1.653 W/Kg; the applicable FCC 10-g SAR limit for handheld portable device is 4W/Kg.

Devices operating close to a base station operate at SAR levels well below the maximum value specified above.

The external antenna connector provided in this device is for GNSS antennas only.

Accessories

The following optional accessories have been approved for use with this device:

P/N 88014-00 GeoExplorer 6000 series AC Power Kit P/N 88056-00 GeoExplorer 6000 Series Vehicle Power Supply P/N 88049-03 USB to Serial Converter Cable

Canada

This Class B digital apparatus complies with Canadian ICES-003. This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.

Cet appareil numérique de la classe B est conforme à la norme NNB-003 du Canada.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada.

Europe

This product has been tested and found to comply with all requirements for CE Marking and sale within the European Economic Area (EEA). It is classified and marked as being Class 2 Radio Equipment under 2000/299/EC, as Bluetooth and wireless LAN approvals are country specific. Please consult your local distributor for more information.

8 GeoExplorer 6000 Series User Guide

EU – Restrictions for Use in the 2.4GHz band

This device may be operated indoors or outdoors in all countries of the European Community using the 2.4GHz band: Channels 1 – 13, except where noted below.

– In France outdoor operation is only permitted using the 2.4 –

2.454 GHz band: Channels 1 – 7.

– In Italy the end-user must apply for a license from the national

spectrum authority to operate this device outdoors.

– In Norway, this unit may not be operated within 20 km of Ny

Alesund

The Trimble GeoExplorer 6000 series has Bluetooth and wireless LAN approval in most EU countries and satisfies the requirements for Radio and Telecommunication Terminal Equipment specified by European Council Directive 1999/5/EC. These requirements provide reasonable protection against harmful inter ference when the equipment is operated appropriately in a residential or commercial environment.

GeoExplorer 6000 series handhelds equipped with wireless cellular modem radios are intended for connection to European Networks operating with GSM 900, or GSM 1800. A copy of the CE Declaration of Conformity for the GeoExplorer 6000 series can be accessed from

http://www.trimble.com/support.shtml.

Australia and New Zealand

This product conforms with the regulatory requirements of the Australian Communications Authority (ACA) EMC and Radiocommunications framework, thus satisfying the requirements for C-Tick Marking and sale within Australia and New Zealand .

Additionally, GeoExplorer 6000 3.5G products that incorporate a modem also comply with the requirements for A-Tick Marking and sale in Australia.

Taiwan – Battery Recycling Requirements

The product contains an internal Lithium-ion battery. Taiwanese regulations require that waste batteries are recycled.

廢電池請回收

Notice to Our European Union Customers

For product recycling instructions and more information, please go to

www.trimble.com/ev.shtml.

Recycling in Europe: To recycle Trimble WEEE (Waste Electrical and Electronic Equipment, products that run on electrical power.), Call +31 497 53 24 30, and ask for the "WEEE Associate". Or, mail a request for recycling instructions to: Tri mble Eu rop e BV c/o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel, NL

GeoExplorer 6000 Series User Guide 9

Safety Information

Radio use

The Trimble® GeoExplorer® 6000 series handheld contains a Bluetooth® radio and Wi-Fi radio. Some models also include a cellular modem radio. In some situations, you may be required to turn off the radios. For example, aviation authority regulations restrict the use of wireless transmission devices on board aircraft.

To prevent the handheld from emitting radio signals, do one of the following:

• To turn off the handheld, press the Power button to display the Power menu

then tap Shutdown.

• To turn off the Bluetooth, Wi-Fi, and wireless cellular modem radios only:

a. Tap the title bar on the Home or Start screen, and then on the pull-down

list, tap the or icon.

b. In the Connectivity or the Phone dialog, select Wireless Manager.

c. Tap

All to turn off all radios. The status fields below the Wi-Fi, Bluetooth,

and Phone buttons change to Off.

Deactivating the integrated Wi-Fi and Bluetooth radios

The GeoExplorer 6000 series handheld is shipped with Wi-Fi and Bluetooth wireless technology activated. To use the Wi-Fi or Bluetooth radio, you need to turn it on (see

Turning on and turning off the integrated radios, page 80).

Note – You may need to deactivate the Wi-Fi and/or Bluetooth radio in the handheld if the country in which you are working does not approve the use of Wi-Fi and/or Bluetooth wireless technology. If you are unsure about whether the GeoExplorer 6000 series handheld’s radios are approved for use in your country, check with your Trimble reseller.

Use the Radio Activation Manager software to deactivate the integrated Wi-Fi and/or Bluetooth radio, or to reactivate the radios if they have been deactivated. The Radio Activation Manager software runs on an office computer.

The latest copy of the software is available for download from the Trimble website. Go to www.trimble.com/support.shtml, click the link for your receiver type (GeoXH, or

GeoXT), click Downloads, click GeoExplorer 6000 Series and then click Radio Activation Manager.

Safety Information

10 GeoExplorer 6000 Series User Guide

Exposure to radio frequency radiation from Bluetooth and Wi-Fi transmitters

This device is approved as a portable device with respect to Radio Frequency (RF) exposure compliance. The radiated output power of the internal wireless radio transmitters is less than 100 milliwatt, which results in exposure levels far below the FCC radio frequency exposure limits, even when operated in close proximity to the body. The internal wireless radios operate within guidelines found in international radio frequency safety standards and recommendations, which reflect the consensus of the international scientific community. Trimble therefore believes the internal wireless radios are safe for use by users. The level of electromagnetic energy emitted is hundreds of times lower than the electromagnetic energy emitted by wireless devices such as mobile phones. However, the use of wireless radios may be restricted in some situations or environments, such as on aircraft. If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radios.

Exposure to radio frequency radiation from cellular wireless transmitters

GeoExplorer 6000 series handhelds equipped with wireless cellular modem radios have been designed and manufactured to meet safety requirements for limiting exposure to radio waves. When used in accordance with the instructions set forth in this manual, the equipment has been independently verified to not exceed the emission limits for safe exposure to radio frequency (RF) energy as specified by the Federal Communications Commission of the U.S. Government in 47 CFR §2.1093.

These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organization through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

The exposure standard for all wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR; the FCC limits for SAR for general population/uncontrolled exposure for partial-body and hands/wrists/feet and ankles are 1.6W/kg and 4W/kg respectively

. Devices operating close to a base station operate at SAR levels well below the maximum value specified above. Tests for SAR on the GeoExplorer 6000 series have been undertaken using the standard operating positions adopted by the FCC that test the device for SAR while it is transmitting at the highest certified power level in all tested frequency bands.

The FCC has granted an Equipment Authorization for this device on the basis that all reported SAR levels have been evaluated to be compliant with the FCC RF exposure guidelines.

In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg

(W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety .

GeoExplorer 6000 Series User Guide 11

Safety Information

SAR information on this device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid; search on FCC IDs:

• JUP 615 - for the GeoExplorer 6000 series standard edition handhelds

• JUP 616 - for the GeoExplorer 6000 series 3.5G edition handhelds

AC adaptor safety

To charge the handheld’s battery, use the international adaptor kit provided with the GeoExplorer 6000 series handheld (see Powering the handheld, page 25).

WARNING – To use AC adaptors safely:

– Use only the AC adaptor intended for the GeoExplorer 6000 series handheld. Using any other AC adaptor can damage the handheld and may void your warranty. Do not use the AC adaptor with any other product. – Make certain that the input voltage on the adaptor matches the voltage and frequency in your location. – Make certain that the adaptor has prongs compatible with your outlets. – Do not use the AC adaptor in wet outdoor areas; it is designed for indoor use only. – Unplug the AC adaptor from power when not in use. – Do not short the output connector. – Be aware that there are no user-serviceable parts in this product. – If the AC adaptor becomes damaged, replace it with a new Trimble AC adaptor.

Electrostatic discharge

WARNING – Static electricity can harm electronic components inside your handheld. To

prevent static damage: – Discharge static electricity from your body before you touch any of the electronic components inside your device, such as a memory module. You can do so by touching an unpainted metal surface.

The GeoExplorer 6000 series is designed for outdoor conditions; however under conditions of low humidity extremely high voltage discharge events are possible. Users are advised that the risk of causing discharge to sensitive electronics can be minimised by avoiding finger contact to the recessed connectors at the sides of the unit.

Battery safety

The removable rechargeable Lithium-ion battery is supplied partially charged. Charge the battery completely before using it for the first time (see Powering the handheld,

page 25). If the battery has been stored for longer than six months, charge it before use.

WARNING – Do not damage the rechargeable Lithium-ion battery. A damaged battery

Safety Information

12 GeoExplorer 6000 Series User Guide

but are not limited to, discoloration, warping, and leaking battery fluid. – Do not store or leave your device near a heat source such as near a fireplace or other heat-generating appliance, or otherwise expose it to temperatures in excess of 70 °C (158 °F) such as on a vehicle dashboard. When heated to excessive temperatures, battery cells could explode or vent, posing a risk of fire. – Do not immerse the battery in water. – Do not use or store the battery inside a vehicle during hot weather. – Do not drop or puncture the battery. – Do not open the battery or short-circuit its contacts.

WARNING – Avoid contact with the rechargeable Lithium-ion battery if it appears to be

leaking. Battery fluid is corrosive, and contact with it can result in personal injury and/or property damage.

- To prevent injury or damage:

- If the battery leaks, avoid contact with the battery fluid.

- If battery fluid gets into your eyes, immediately rinse your eyes with clean water and seek medical attention. Do not rub your eyes!

- If battery fluid gets onto your skin or clothing, immediately use clean water to wash off the battery fluid.

- Do not open the battery or short-circuit its contacts.

WARNING – Charge and use the rechargeable Lithium-ion battery only in strict

accordance with the instructions. Charging or using the battery in unauthorized equipment can cause an explosion or fire, and can result in personal injury and/or equipment damage. To prevent injury or damage: – Do not charge or use the battery if it appears to be damaged or leaking. – Charge the Lithium-ion battery only in a Trimble product that is specified to charge it. Be sure to follow all instructions that are provided with the battery charger. – Discontinue charging a battery that gives off extreme heat or a burning odor. – Use the battery only in Trimble equipment that is specified to use it. – Use the battery only for its intended use and according to the instructions in the product documentation.

Storage card use

The GeoExplorer 6000 series handheld provides a storage card slot, providing an alternative storage location to the storage memory in the handheld.

WARNING – Static electricity can harm electronic components inside your handheld. To

WARNING – The presence of any dust or moisture in the storage card slot may adversely

affect the device and void your Trimble warranty. To prevent dust or moisture entering the storage card slot: – Make certain that the storage card slot door is attached correctly when you are using the handheld outdoors. – When inserting or removing a storage card, place the handheld on a dust-free indoor surface.

GeoExplorer 6000 Series User Guide 13

Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Radio use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Deactivating the integrated Wi-Fi and Bluetooth radios . . . . . . . . . . . . . . . . . . . . . 9

Exposure to radio frequency radiation from Bluetooth and Wi-Fi transmitters . . . . . . . . . . 10

Exposure to radio frequency radiation from cellular wireless transmitters . . . . . . . . . . . . . 10

AC adaptor safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Electrostatic discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Battery safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Storage card use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

About the GeoExplorer 6000 series handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Supported GNSS field software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

What’s in the box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Use and care of the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Storing the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Technical assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Additional help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Windows error reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Your comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Parts of the GeoExplorer 6000 series handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Keypad buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Powering the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

AC adaptor safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Battery safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Inserting the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Charging the battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Checking the level of battery power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Swapping the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Turning on and turning off the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Suspend mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Swap Battery mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Resetting the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Performing a soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Performing a hard reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Resetting to factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

14 GeoExplorer 6000 Series User Guide

Storing data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Storage cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Installing and removing a SIM card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Fitting the hand strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3 Using the Windows Mobile Operating System . . . . . . . . . . . . . . . . 39

Parts of the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Battery status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Speaker status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Network and modem status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Pre-installed programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Interacting with the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Entering information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using the on-screen keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Making a recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Personalizing the handheld. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Device lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Sounds and notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Messaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Synchronizing email messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Connecting directly to an email server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4 Connecting to an Office Computer. . . . . . . . . . . . . . . . . . . . . . . 55

Connection management software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Installing the Windows Mobile Device Center . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Installing ActiveSync technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Connecting the handheld to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Managing the connection using the Windows Mobile Device Center . . . . . . . . . . . . . . . . 57

Managing the connection using ActiveSync technology. . . . . . . . . . . . . . . . . . . . . . . . . 59

Installing software onto the handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

5 Using the GNSS Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Supported GNSS field software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

TerraSync software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Esri ArcPad software and the Trimble GPScorrect extension . . . . . . . . . . . . . . . . . 62

GPS Controller software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

GNSS Connector software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Other GNSS field applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Configuring the GNSS field software to connect to the receiver . . . . . . . . . . . . . . . . . . . . 63

GeoExplorer 6000 Series User Guide 15

GNSS COM ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Connecting to the COM port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Using the GNSS field software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Starting the GNSS field software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Viewing available GNSS satellites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Resetting the GNSS receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Improving GNSS productivity using Floodlight satellite shadow reduction technology . . . . . 66

Ensuring the accuracy of your GNSS data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Accuracy settings and using accuracy-based logging . . . . . . . . . . . . . . . . . . . . . . 68

Connecting to a real-time differential correction source . . . . . . . . . . . . . . . . . . . . 69

Connecting to an external antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Planning a data collection session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Activating the Floodlight technology and the NMEA output options . . . . . . . . . . . . . . . . 74

Differential GNSS explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Real-time DGNSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Postprocessed DGNSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Postprocessed real-time DGNSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Outputting NMEA data to external equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Configuring NMEA output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

6 Getting Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Wireless connection information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Deactivating the integrated radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Turning on and turning off the integrated radios . . . . . . . . . . . . . . . . . . . . . . . . . 80

Connecting wirelessly to other devices and networks . . . . . . . . . . . . . . . . . . . . . . 82

Connecting to a cellular network from the modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Connecting to a Wi-Fi access point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Connecting to a Bluetooth-enabled device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Connecting to a Bluetooth device as a client . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Providing Bluetooth services as a host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Setting up a Bluetooth connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Connecting to a Bluetooth-enabled phone for Internet access or real-time corrections

(including VRS networks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Connecting to the Internet through a Bluetooth-enabled phone using the Bluetooth PAN

profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Connecting to a Bluetooth-enabled serial device . . . . . . . . . . . . . . . . . . . . . . . . .101

Connecting to an office computer using Bluetooth wireless technology . . . . . . . . . .104

Outputting GNSS data to other devices using Bluetooth wireless technology. . . . . . . 107

Enabling other devices to transfer files using Bluetooth wireless technology . . . . . . .108

Beaming files to or from another device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109

Accessing a corporate network through your Internet connection. . . . . . . . . . . . . . 110

Connecting to other devices using the USB to serial converter . . . . . . . . . . . . . . . . . . . .111

Connecting to external devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

16 GeoExplorer 6000 Series User Guide

7 Using the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Parts of the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114

Starting the camera application and capturing photos or video. . . . . . . . . . . . . . . . . . . . 114

Adjusting camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Camera and Video options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116

8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Power issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

Backlight issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119

Touch screen issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119

Storage card issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Keypad issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Connection issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120

ActiveSync technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Windows Mobile Device Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121

Network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121

Bluetooth wireless technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

Wi-Fi connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123

Internal cellular modem connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124

GNSS receiver issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125

Real-time DGNSS issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127

Recommended GNSS settings for maximum precision and productivity . . . . . . . . . . . . . . 128

CHAPTER

GeoExplorer 6000 Series User Guide 17

Introduction 1

In this chapter:

Q About the GeoExplorer 6000

series handheld

Q What’s in the box?

Q Accessories

Q Use and care of the handheld

Q Technical assistance

Q Your comments

The GeoExplorer 6000 Series User Guide describes how to set up and use the Trimble

GeoExplorer

6000 series handheld. The information in this guide supplements the information in the GeoExplorer 6000 Series Quick Start Guide, which you received with the handheld.

This guide describes how to:

• use the Microsoft

Windows Mobile®

version 6.5 operating system.

• use the handheld’s integrated GNSS

receiver.

• synchronize information between a

computer and the handheld.

• exchange information between the

handheld and other devices.

• connect to the Internet or to a computer

network.

• use the integrated camera.

Even if you have used other Global Navigation Satellite System (GNSS) products before, Trimble recommends that you spend some time reading this guide to learn about the special features of the product. If you are not familiar with GNSS, go to the Trimble website (www.trimble.com) for more information.

1 Introduction

18 GeoExplorer 6000 Series User Guide

About the GeoExplorer 6000 series handheld

The GeoExplorer 6000 series includes the GeoXH™ and GeoXT

™

handhelds. These handhelds combine a Trimble GNSS receiver with a field computer powered by Microsoft Windows Mobile version 6.5 operating system.

The GeoExplorer 6000 series handheld has built-in Bluetooth

wireless technology for cable-free connection to other devices, and Wi-Fi connectivity for connections to networks. In addition, some GeoExplorer 6000 series handheld editions are equipped with a wireless cellular modem for downloading and transmitting data over the Internet.

The GeoXT handheld uses EVEREST

™

multipath rejection technology to provide submeter accuracy. The GeoXH handheld uses both EVEREST and H-Star

™

technology to provide decimeter (10 cm) accuracy, either in real time or after postprocessing. In addition, both the GeoXH and GeoXT handhelds are compatible with Trimble Floodlight

™

satellite shadow reduction technology for improved productivity in conditions where sky view is obstructed by buildings, trees, or landscape features. For more information, see Chapter 5, Using the GNSS Receiver.

Supported GNSS field software

To collect GNSS data with the GeoExplorer 6000 series handheld, you must install GNSS field software onto the handheld. You can use the GeoExplorer 6000 series handheld with the following GNSS field software:

• Trimble TerraSync

™

software, for configuring real-time differential correction

options and for productive GIS data collection and maintenance.

• The Trimble GPScorrect

™

extension for Esri ArcPad software, for configuring real-time differential correction options and for productive GIS data collection and maintenance.

• Trimble GPS Controller software, for configuring real-time differential

correction options and NMEA output settings.

• Other GNSS field software that accepts NMEA messages. To use NMEA Output

messages, you must purchase and activate the NMEA output option. See

Activating the Floodlight technology and the NMEA output options, page 74

For more information, see Chapter 5, Using the GNSS Receiver.

GeoExplorer 6000 Series User Guide 19

Introduction 1

What’s in the box?

When you unpack the GeoExplorer 6000 series handheld, check that you have received all the components:

Inspect all contents for visible damage (scratches, dents) and if any components appear damaged, notify the shipping carrier. Keep the shipping and packaging material for the carrier’s inspection.

Accessories

The following optional accessories are available:

For more information, go to www.trimble.com/geoxh.shtml, or

www.trimble.com/geoxt.shtml.

• GeoExplorer 6000 series handheld

• Carry pouch

• AC adaptor kit

• Microsoft Getting Started CD and licence

• Anti-reflection screen protector kit

• USB data cable

• Hand strap kit

• Spare stylus and lanyard

• A sheet of device ID labels

• Rechargeable battery pack

• USB to serial converter cable

• Null modem cable

• Hard carry case

• Range pole

• Range pole bracket

• Vehicle mounting bracket

• Te mp es t

™

antenna

• To rn a do

™

antenna

• Pole-mountable ground plane

• Backpack kit

• Screen protectors (2 pack)

• Stylus kit

• GeoBeacon

™

receiver (receives differential corrections from a beacon network)

• Replacement battery pack

• Replacement international AC adaptor

• Replacement carry pouch

• Replacement hand strap kit

Requires USB to serial converter (sold separately)

Compatible with GeoXH/XT handhelds for improved yield. Also improves accuracy for the GeoXT handheld

only.

Compatible with the GeoXH handheld for improved accuracy.

1 Introduction

20 GeoExplorer 6000 Series User Guide

Use and care of the handheld

To protect the GeoExplorer 6000 series handheld when not in use, Trimble recommends storing the handheld in the pouch provided.

When using the handheld:

• To protect the touch screen from pressure and abrasive objects, Trimble

recommends that you apply one of the screen protectors provided with the GeoExplorer 6000 series handheld.

• Protect the touch screen by using your finger or the stylus provided, and avoid

using excessive pressure and sharp or abrasive objects.

• Keep the outer surface free of dirt and dust.

• Ensure that protective covers and doors are appropriately fitted to the external

antenna port, SIM, and storage card areas, so that they are kept free from dirt, dust, fluid ingress & electrostatic discharge (see Storage cards, page 35).

• Protect the handheld from extreme temperatures. For example, do not leave the

handheld on the dashboard of a vehicle.

• When the battery is removed, the handheld is not waterproof. Avoid exposing

the internals of the handheld to dust and moisture when removing the battery. Trimble recommends that you only swap the battery indoors or from inside a vehicle.

• Use the handstrap provided with the GeoExplorer 6000 series handheld.

To clean the handheld, wipe it with a clean dry cloth. Do not immerse the handheld in water.

Storing the handheld

If you are not going to use the handheld for three months or more, Trimble recommends that you do not leave the handheld in Suspend mode (see page 31). Instead, partially charge the battery and then turn off the handheld.

To prepare the GeoExplorer 6000 series handheld for storage:

1. Transfer any data that you need to an office computer.

2. Charge the battery to approximately 30%.

3. Press the

Power key for one second until the Power menu appears and then tap

Shutdown.

4. Store the handheld at room temperature.

To use the GeoExplorer 6000 series handheld after storage:

1. Press the

Power key to turn on the handheld.

2. Recharge the battery (see Charging the battery, page 27).

GeoExplorer 6000 Series User Guide 21

Introduction 1

Technical assistance

Technical support

Go to the GeoExplorer 6000 series handheld technical support page (www.trimble.com/geoxh_ts.asp, or www.trimble.com/geoxt_ts.asp) on the Trimble website for the latest support information about the software, including:

• support notes detailing support issues

• documentation

• the latest files available for download

Additional help

If you still cannot find the information that you need, contact your Trimble reseller.

Windows error reporting

If for any reason a Microsoft Windows Error Reporting dialog appears, indicating that the handheld or Trimble GNSS field software has encountered a problem and needs to close, you are prompted to send an error report to Microsoft.

Trimble recommends that you click

Send and then click any subsequent links that are

used to obtain additional information.

Trimble can access the report that is sent to Microsoft and use it to improve the GeoExplorer 6000 series handheld.

Your comments

Your feedback about the supporting documentation helps Trimble to improve it with each revision. Email your comments to ReaderFeedback@trimble.com.

1 Introduction

22 GeoExplorer 6000 Series User Guide

CHAPTER

GeoExplorer 6000 Series User Guide 23

Getting Started 2

In this chapter:

Q Parts of the GeoExplorer 6000

series handheld

Q Keypad buttons

Q Powering the handheld

Q Turning on and turning off the

handheld

Q Resetting the handheld

Q Storing data

Q Installing and removing a SIM

card

Q Fitting the hand strap

This chapter describes the main features of the GeoExplorer 6000 series handheld, and provides the information you need to get up and running with the handheld.

2 Getting Started

24 GeoExplorer 6000 Series User Guide

Parts of the GeoExplorer 6000 series handheld

The following diagrams show the main parts of the handheld.

Figure 2.1 Parts of the GeoExplorer 6000 series handheld

Keypad buttons

The GeoExplorer 6000 series handheld has a keypad for fast, easy access to common actions. LEDs provide visual notifications of system events.

Figure 2.2 GeoExplorer 6000 series handheld keypad area

Camera Lens

Handstrap

Removable battery

Lanyard tether

Stylus

GNSS receiver

External GNSS antenna connector

Touch panel

SIM card door

SD card door

Application keys

Camera control key

Power key

USB door

Notification LEDs Microphone

Speaker

Barometer

display

Identification label zone

Ambient light sensor

Left softkey

Right softkey

Camera control key

Speaker

Power key

Microphone

LEDs: Power, GNSS, Radios

GeoExplorer 6000 Series User Guide 25

Getting Started 2

The function of each key is described below:

Tip – To lock the screen and handheld keys without turning off the handheld, use the device lock option (see Device lock, page 49).

The function of each LED is described below:

Powering the handheld

The GeoExplorer 6000 series handheld contains a removable rechargeable Lithium-ion battery.

Note – Charge the battery completely before using the handheld for the first time. If the battery has been stored for longer than six months, charge it before use. Trimble recommends charging the battery for five hours to recharge it fully.

When fully charged, the handheld battery provides enough power for a full working day (10 hours) using the internal GNSS antenna and with the backlight on at the default settings.

Note – Cold temperatures, or using Bluetooth wireless technology, Wi-Fi, or the wireless cellular modem consumes additional battery power and so shortens battery life between charges.

Key Description

Power key Press briefly (less than one second) to turn on the handeld, or to turn off

the handheld (put it into Suspend mode). To access other power options, or to reset the handheld, press and hold

for one second until the Power menu appears (see Turning on and

turning off the handheld, page 31, or see Resetting the handheld, page 33).

Left and right soft keys

By default these keys perform the same action as the left and right softkeys in the tile bar.

Alternatively, program these keys to perform a selected action. To program the keys, use the Buttons control (see Buttons, page 46).

Camera Control key

Press to activate and operate the camera (see Chapter 7, Using the

Camera).

Key LED Description

Battery status Battery charging is complete.

Battery is charging.

... ... Battery level is critically low (<5% remaining).

Battery fault.

GNSS receiver status ... ... Receiver is on, and GNSS positions are available.

... ... Receiver is on, but GNSS positions are not available.

Wireless radio status ... ... A wireless radio is turned on.

2 Getting Started

26 GeoExplorer 6000 Series User Guide

AC adaptor safety

WARNING – To use AC adaptors safely:

Battery safety

WARNING – Do not damage the rechargeable Lithium-ion battery. A damaged battery

can cause an explosion or fire, and can result in personal injury and/or property damage. To prevent injury or damage: – Do not use or charge the battery if it appears to be damaged. Signs of damage include, but are not limited to, discoloration, warping, and leaking battery fluid. – Do not store or leave your device near a heat source such as near a fireplace or other heat-generating appliance, or otherwise expose it to temperatures in excess of 70 °C (158 °F) such as on a vehicle dashboard. When heated to excessive temperatures, battery cells could explode or vent, posing a risk of fire. – Do not immerse the battery in water. – Do not use or store the battery inside a vehicle during hot weather. – Do not drop or puncture the battery. – Do not open the battery or short-circuit its contacts.

WARNING – Avoid contact with the rechargeable Lithium-ion battery if it appears to be

leaking. Battery fluid is corrosive, and contact with it can result in personal injury and/or property damage.

- To prevent injury or damage:

- If the battery leaks, avoid contact with the battery fluid.

- If battery fluid gets into your eyes, immediately rinse your eyes with clean water and seek medical attention. Do not rub your eyes!

- If battery fluid gets onto your skin or clothing, immediately use clean water to wash off the battery fluid.

- Do not open the battery or short-circuit its contacts.

WARNING – Charge and use the rechargeable Lithium-ion battery only in strict

GeoExplorer 6000 Series User Guide 27

Getting Started 2

– Use the battery only in Trimble equipment that is specified to use it. – Use the battery only for its intended use and according to the instructions in the product documentation.

Inserting the battery

To insert the battery into the handheld:

1. Slide the battery into the cavity with the label facing upwards (as shown in

Figure 2.3).

2. Push the battery in until it clicks into place.

CAUTION – Make sure that the battery is fully inserted and that both the left and right latches are fully engaged. If the battery is not properly inserted, it may fall out if the device is dropped.

Figure 2.3 Inserting the battery

Charging the battery

Charge the battery in the handheld, or, if you have a spare battery, you can charge it outside the handheld.

To charge the battery:

1. Connect one end of the AC adaptor cable to the battery and the other to an AC power outlet. An international adaptor kit is provided with the handheld.

2. Turn off the handheld or put the handheld in Suspend mode (see page 31).

Note – Trimble recommends that you charge the handheld at or below normal room temperature (0 to 30 °C / 32 to 86 °F ).

2 Getting Started

28 GeoExplorer 6000 Series User Guide

3. Leave the battery to charge. It may take up to five hours for the handheld to charge completely.

When the handheld is charging, the Power LED on the handheld is solid orange. If the Power LED changes to red, a battery charging fault has occured. For more information, see page 28.

When fully charged, the Power LED is green.

The Power LED on the keypad on the handheld indicates the battery power or charging status, as shown below:

Note – During normal charging, the battery may become hotter than the maximum temperature allowed (40 °C or 104 °F). If this happens, charging is automatically suspended until the battery cools and then charging automatically restarts. During this time the battery icon in the title bar shows , to indicate that the handheld is running on external power. It may take about one hour for the battery to cool.

Avoid keeping the battery at full charge at high temperatures. For more information, see Storing the handheld, page 20.

Note – The life of the battery can be significantly shortened if power is constantly supplied to the handheld. To avoid this issue, connect the handheld to an external power source only when the battery requires charging. Once fully charged, disconnect the external power source and allow the battery to discharge through normal use.

Checking the level of battery power

To check the level of battery power remaining at any time while the device is running, tap the battery icon in the title bar of the Home screen and then tap in the pulldown list.

Power source LED state Handheld/battery state

Battery power Off Handheld is turned off or is in Suspend mode.

Off Handheld is turned on and battery level is good.

.... Flashing red: Handheld is turned on and battery level is

critically low (<5%).

External power Solid orange: Battery is charging.

Solid red: Charging fault - for example, there is a problem with the battery, or the temperature of the battery has exceeded the acceptable temperature range.

Solid green: Charging is complete.

GeoExplorer 6000 Series User Guide 29

Getting Started 2

The Power control appears, displaying the Battery tab.

When the handheld battery is recharging from an external power source, the battery icon in the Home screen changes to . You can still tap the icon to view the level of battery power.

To check the level of battery power remaining on a spare battery or one that is not inside the handheld, press the battery icon on the battery pack label. The level of charge indicator will light up with the approximate level of battery power remaining on the battery. Each LED represents a 20% increment in battery capacity.

Low battery indicators

When the battery level reaches:

• 15%, the battery icon in the title bar of the Home screen changes to .

• 10%, the Power LED on the handheld flashes red and the Main battery low

message appears on the handheld.

• 5%, the Main battery very low message appears on the handheld.

Trimble recommends that you recharge the battery when any of these indicators appear.

Swapping the battery

If the battery runs low while you are working, you can swap the battery without the need to close files and shut down the handheld, and can resume working straight away.

1. Save any open files.

2. Ensure that you have a spare battery close by with sufficient charge to keep working (see Checking the level of battery power, page 28).

3. Turn off the handheld or put the handheld in Swap Battery mode (see page 32).

CAUTION – In Swap Battery mode, the battery LED shows as a red warning. When the device is ready, the red LED turns off, and the battery can be safely swapped. Generally the red LED will only display for half a second or less, but it may display for three seconds or so. Do not remove the existing battery until the red LED turns off. Removing the battery when the red LED warning light is still on will make the device reboot when the battery is swapped. Do not remove the existing battery until the red LED turns off.

2 Getting Started

30 GeoExplorer 6000 Series User Guide

4. Remove the old battery by pinching the battery latches together until the battery is ejected. Slide the battery out.

CAUTION – The handheld is not sealed from water and dust when the battery is removed. Trimble recommends only removing the battery for short periods of time and only removing the battery indoors or from inside the protection of a vehicle.

5. Insert the new battery (see Inserting the battery, page 27).

CAUTION – The handheld has enough power to keep the device running for approximately 30 seconds with the battery removed. If the power drains before the battery is restored the device will shut down. Trimble recommends saving open files before swapping the battery.

6. Press the Power key to resume your session.

Conserving power

Although the handheld battery can operate for a full day without recharging, Trimble recommends that you do the following to reduce power consumption:

• Set the handheld to automatically turn off when idle. For more information, see

Suspend mode, page 31.

• Set the backlight to automatically turn off when the handheld is idle for a

specified time. For more information, see Backlight, page 51.

• Turn off the integrated Bluetooth, Wi-Fi, and wireless cellular modem radios

whenever you are not using them. For more information, see Turning on and

turning off the integrated radios, page 80.

• Disconnect from the integrated GNSS receiver when GNSS data is not required,

using the application’s Disconnect or Deactivate GNSS command. When you disconnect from GNSS, the integrated GNSS receiver switches off and stops drawing power.

Note – Do not disconnect from GNSS if you will be reconnecting within about five minutes. A GNSS application can take up to 30 seconds to reactivate the integrated GNSS receiver, so disconnecting to save power can cost time.

GeoExplorer 6000 Series User Guide 31

Getting Started 2

Turning on and turning off the handheld

If the screen on the handheld is blank, the handheld is in Suspend mode or Battery Change mode (see page 31) or has been shut down. To turn on the handheld, press the

Power key briefly (less than one second).

To turn off the handheld and put the handheld into Suspend mode, press the

Power

key briefly (less than one second). The handheld is placed in a very low power state, but the Bluetooth and wireless cellular modem radios may remain active (see Suspend

mode, page 31)

To completely shut down the handheld, press the

Power key for one second until the

Power menu appears and then tap

Shutdown. All running applications are shut down,

and the handheld is completely turned off.

The options available from the Power menu are as follows:

Suspend mode

When you press the Power key to turn off the handheld, the handheld goes into Suspend mode. This is a low-power mode that maintains the main memory contents and keeps applications running but does not allow you to operate any of the handheld’s functions. The handheld appears to be turned off. The integrated GNSS receiver is turned off and any application using GNSS is disconnected.

If a wireless radio is turned on (the

LED is flashing), the Wi-Fi radio will be turned

off, and the Bluetooth and wireless cellular modem radios will remain turned on. The handheld is capable of receiving data via Bluetooth or the cellular modem radio while it is in Suspend mode. The handheld is able to automatically wake up to calendar alarms if it is in Suspend mode.

CAUTION – To save battery power, use the Wireless Manager to turn off the wireless radios before you place the handheld into Suspend mode.

Button Used to...

Power Settings quickly access the Power Settings menus.

Backlight Settings quickly access the Backlight Settings menus.

Swap Battery put the handheld into Swap Battery mode. This is a low-power mode. The

handheld, the integrated receiver, and all wireless radios are turned off, and you cannot operate the handheld.

Shutdown put the handheld into Shutdown mode. Applications are shut down and

the handheld is completely turned off.

Reset restart the handheld. If the handheld stops responding to the stylus, or if

it does not respond when you press any of the keypad buttons, try a soft reset. For more information, see Resetting the handheld, page 33.

access the Align Screen Sequence. You can also press the left application key to access the Align Screen Sequence. If at any time the touch screen does not respond correctly to stylus taps, start the screen alignment sequence and follow the on-screen instructions.

2 Getting Started

32 GeoExplorer 6000 Series User Guide

To turn on the handheld when it is in Suspend mode, press the Power key. The handheld is immediately ready for operation. There may be a delay of up to 30 seconds while the integrated GNSS receiver and the Wi-Fi radio automatically reactivate.

You can configure the handheld to automatically enter Suspend mode when it has been idle for a specified time. By default, the handheld is set to enter Suspend mode if it is not used for one minutes.

To change the time before the handheld enters Suspend mode:

1. Tap the title bar of the Home or the Start screen and then tap . The Power control appears, displaying the Battery tab.

2. Tap the Advanced tab.

3. From the On battery power option, select the Tur n off screen if device not used for check box and then select the idle time from the drop-down list.

4. Tap

OK.

Swap Battery mode

Swap Battery mode is a low power mode that allows you to remove an empty battery and replace it with a fresh battery without closing files and applications; it maintains the main memory contents and keeps applications running but does not allow you to operate any of the handheld's functions. The handheld appears to be turned off. The integrated GNSS receiver is turned off and any application using GNSS is disconnected. All wireless radios are powered down and the device is unable to be automatically woken up.

When in Swap Battery mode, the handheld operates on backup power with the battery removed. From the time that the battery is removed, you have approximately 45 seconds to replace the battery before the backup power supply is consumed and the handheld shuts down.

To switch to Swap Battery mode, press and hold the

Power key and then tap Swap

Battery

on the Power menu. The battery LED shows as a red warning. When the device is ready, the red LED turns off, and the battery can be safely swapped. Generally the red LED will only display for half a second or less, but it may display for three seconds or so. Do not remove the existing battery until the red LED turns off.

CAUTION – Removing the battery when the red LED warning light is still on will make the device reboot when the battery is swapped. Do not remove the existing battery until the red LED turns off.

GeoExplorer 6000 Series User Guide 33

Getting Started 2

To turn on the handheld when it is in Swap Battery mode, ensure that the battery is correctly installed and then press the

Power key. The handheld is immediately ready

for operation. There may be a delay of up to 30 seconds while the integrated GNSS receiver automatically reactivates.

The wireless radios will not automatically reactivate; use the Wireless Manager to manually turn on the wireless radios.

Resetting the handheld

If the screen on the handheld is blank, the handheld has turned off. Press the Power button to turn on the handheld.

If the handheld stops responding to the stylus, or if it does not respond when you press any of the keypad buttons, you may need to reset it by performing a soft or hard reset.

You can also reset the handheld to its factory default settings by performing a factory reset.

Performing a soft reset

A soft reset is similar to restarting a computer. A soft reset retains all settings and device data that you have previously saved on the handheld. The handheld saves any unsaved data, closes all open applications, and then restarts.

To perform a soft reset, press the

Power key for one second until the

Power menu appears and then tap the

Reset button.

Performing a hard reset

A hard reset retains settings and data that you have previously saved on the handheld. However, any unsaved data may be lost.

Note – Perform a hard reset only if a soft reset does not resolve the problem.

To perform a hard reset, press and hold the

Power key until the boot screen appears

and then release the

Power key.

2 Getting Started

34 GeoExplorer 6000 Series User Guide

Resetting to factory default settings

Reset the handheld to factory default settings to restore the handheld to it’s original state, or only if a soft reset and then a hard reset does not resolve the problem.

CAUTION – Resetting the handheld to factory default settings erases all data, installed applications, and settings stored in the handheld, except for any data or applications that were pre-installed on the handheld or are stored on a storage card. It does not change the language of the operating system used on the handheld.

CAUTION – If you have encrypted files on a storage card and you reset the handheld to factory default settings, the encryption key on the handheld is deleted. This means that any files you have encrypted on a storage card are permanently locked and unreadable by any device. For more information, see Encrypting files on storage cards, page 36.

Tip – To quickly and easily restore data deleted by performing a factory reset, synchronize the handheld with a computer before you reset the handheld to the factory default settings. Once the handheld is reset then resynchronize the handheld with the computer.

To reset the handheld to the factory default settings:

1. Press and hold the two application keys on the handheld.

2. While holding the application keys, press and hold the

Power key until the

device reboots.

3. Keep holding the two application keys until the factory reset screen appears.

4. Follow the on-screen instructions to continue the factory reset.

GeoExplorer 6000 Series User Guide 35

Getting Started 2

Storing data

The handheld has two types of memory:

• Storage memory is similar to the hard disk in a

computer, and is used for storing programs and data.

• Program memory is similar to the RAM in a

computer, and is used for running programs. You cannot use it to save data.

To check the storage capacity on the handheld, tap

/ Settings / System / Memory. The Storage and Program columns show the current memory available, and the memory that is already in use.

Pre-installed documents and program files are not affected by power loss or resetting. However, you can still lose data if you accidentally delete or overwrite it.

CAUTION – The Windows Mobile version 6.5 operating system does not include a Recycle Bin. When you delete files from the handheld, they are deleted permanently.

Trimble recommends that you regularly copy important data to an office computer. For more information, see Connecting to an Office Computer, page 55.

Storage cards

As an alternative to internal storage, you can save data to a removable card. Use either an SD or SDHC (high capacity SD) card to securely transfer data to and from another device that supports SD or SDHC cards.

Note – The GeoExplorer 6000 series handheld does not support SDIO (Secure Digital Input/Output) or SDXC (Secure Digital Extended Capacity) cards.

WARNING – The presence of any dust or moisture in the storage card slot may adversely

WARNING – Static electricity can harm electronic components inside the handheld. To

To insert an SD or SDHC card:

1. Place the handheld on a dust-free indoor surface.

2. Flip open the storage card slot door on the side of the handheld.

2 Getting Started

36 GeoExplorer 6000 Series User Guide

3. Insert the storage card into the storage card slot with the gold contacts facing down. Gently press the card until you hear a click, and the card is locked into place.

4. Close the storage card slot door.

When you select the Save As option in an application, the storage card appears in the list of available storage locations.

Note – Do not store required data or applications to a storage card if the card will be removed. Data saved to a storage card is available only when the card is inserted in the handheld.

To remove the storage card from the storage card slot, gently press the card in and then let go. The card pops out.

Encrypting files on storage cards

To prevent sensitive data on an SD or SDHC card from being used if the card is lost or stolen, files can be encrypted as they are placed on the card.

When encryption is enabled, an encryption key is stored on the handheld. Files are encrypted as they are copied or written to the storage card. Files already saved on storage cards before enabling encryption are not automatically encrypted.

Note – Because the encryption key is stored on the handheld, encrypted files are only readable on the handheld on which they are initially encrypted. It is not possible to read encrypted files on the storage card with any other device, including another GeoExplorer 6000 series handheld or an office computer.

CAUTION – If you reset the handheld to the factory default settings, the encryption key is deleted and the handheld is no longer able to read any encrypted files on a storage card. This means that any files you have encrypted are permanently locked and unreadable by any device. To avoid being unable to read previously encrypted files, Trimble recommends that you use another device, such as an office computer, as the primary location for storing important data and to control the encryption of important files.

To enable encryption of files as they are written to a storage card:

1. Tap / Settings / System / Encryption.

2. Select the Encrypt files when placed on a storage cards check-box.

Note – Encrypted files appear as ordinary files on the handheld they were encrypted on. If the storage card is inserted in another device, the files appear with a .menc file extension and cannot be opened.

To disable encryption, clear the Encrypt files when placed on a storage cards check-box.

Note – Disabling encryption does not remove encryption from any existing files on the storage card, but ensures that new files placed onto the storage card are not encrypted.

To encrypt files that are already stored on a storage card:

1. Copy the files to the handheld’s internal storage or to an office computer.

2. Ensure encryption is enabled on the handheld.

GeoExplorer 6000 Series User Guide 37

Getting Started 2

3. Copy the files back to the storage card. The files are encrypted as they are written to the storage card.

To remove encryption from files so they can be read by other devices:

1. Insert the storage card in the handheld and then connect the handheld to an office computer using Microsoft ActiveSync

technology or the WMDC.

2. Copy the encrypted files from the storage card to the office computer.

3. To use the decrypted files on the handheld, copy the files from the office computer to the handheld’s internal storage.

4. To store the decrypted files on a storage card, ensure encryption is not enabled on the handheld and then copy the decrypted files from the office computer to the storage card.

Installing and removing a SIM card

The GeoExplorer 6000 series 3.5G edition handhelds are equipped with a cellular modem. To use the integrated modem, the 3.5G edition handhelds require a SIM card.

CAUTION – The SIM card and its contents can be easily damaged by scratches or bending.

CAUTION – The presence of any dust or moisture in the SIM card slot may adversely affect the device and void your Trimble warranty. To prevent dust or moisture entering the SIM card slot:

- Make certain that the SIM card slot door is attached correctly when you are using the handheld outdoors.

- When inserting or removing a SIM card, place the handheld on a dust-free indoor surface.

CAUTION – Static electricity can harm electronic components inside the handheld. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components inside your device, such as a memory module. You can do so by touching an unpainted metal surface.

To insert a SIM card :

1. Turn off the handheld.

2. Place the handheld on a dust-free indoor surface.

3. Flip open the SIM card slot door on the side of the handheld.

4. Insert the card into the SIM card slot with the gold contacts facing down. Gently press the card until you hear a click, and the card is locked into place.

5. Close the SIM card slot door.

To remove the SIM card:

1. Follow steps 1 to 3 above.

2. Gently press the card in and then let go. The card pops out.

2 Getting Started

38 GeoExplorer 6000 Series User Guide

3. Gently slide the card out of the slot.

Fitting the hand strap

The hand strap and screws are provided in the box with the handheld. To fit the hand strap:

1. Align the upper hand strap bracket with the two mounting holes and then use a coin or screwdriver to tighten the screws.

2. Stretch the hand strap to align the bottom hand strap bracket with the mounting hole and then use a coin or screwdriver to tighten the screw.

CHAPTER

GeoExplorer 6000 Series User Guide 39

Using the Windows Mobile Operating System

In this chapter:

Q Parts of the screen

Q Interacting with the handheld

Q Status indicators

Q Pre-installed programs

Q Entering information

Q Personalizing the handheld

Q Messaging

The GeoExplorer 6000 series handheld is powered by the Windows Mobile 6.5 operating system.

This chapter describes the main features of this generation of the Windows Mobile operating system.

3 Using the Windows Mobile Operating System

40 GeoExplorer 6000 Series User Guide

Parts of the screen

The main parts of the Home screen and the Start screen are shown below.

Start screen

Tap any item on the menu to open it.

Start button

Tap to open the Start screen, where you can access programs and system controls.

Title bar

Contains status icons for important system functions.

Tile bar

Contains touchable tiles providing access to applications, menus, and notifications.

Home screen

Provides access to the key functions on your device. Scroll, and tap any item to open it.

Connectivity icons

Tap either icon to access the Wireless Manager.

Lock device

Tap to lock the screen. Once locked, you have multiple points of unlock entry depending on the current status.

Pull-down list

Tap anywhere on the title bar to open the title bar pull-down list, where you can access connectivity controls (the Wireless Manager), battery information, time and date settings, and volume.

GeoExplorer 6000 Series User Guide 41

Using the Windows Mobile Operating System 3

Status indicators

Status indicators that appear in the title bar at the top of the screen are as follows:

Battery status indicators

The battery status icon on the title bar of the Home screen or the Start screen shows the status of the battery charge. Tap the title bar and then on the pull-down list tap the

icon to access the Power control dialog. See Checking the level of battery power,

page 28.

Speaker status indicators

The speaker status icon on the title bar of the Home screen or the Start screen shows the status of the speaker. Tap the title bar and then on the pull-down list tap the icon to adjust the volume and to turn the speaker on or off.

Icon Description

Battery has full charge

Battery has high charge

Battery has medium charge

Battery has low charge

Battery has very low charge (20% or less)

Battery charging/using external power

Icon Description

Speaker is on

Speaker is off

3 Using the Windows Mobile Operating System

42 GeoExplorer 6000 Series User Guide

Network and modem status indicators

The network and modem status icons on the title bar of the Home screen or the Start screen show the status of each radio. Tap the title bar and then on the pull-down list tap the or icon. In the Connectivity or Phone dialog, select Wireless Manager and turn on or turn off the radio.

Icon

Connected to ActiveSync or the Windows Mobile Device Center (WMDC) on a computer

Connected to a Bluetooth-enabled phone

Disconnected from ActiveSync or WMDC

Disconnected from a Bluetooth-enabled phone

Wi-Fi radio is on

Wi-Fi is detected

Connected to a wireless network

Maximum cellular modem signal strength

No cellular modem signal

Cellular modem is turned off

No cellular service

Searching for cellular modem service

Data is transferring using the cellular modem

No SIM card

UMTS network is available

UMTS network is connecting

UMTS connection is active

3G+ network is available

Analog network is available

EDGE network is available

EDGE network is connecting

EDGE connection is active

GPRS network is available

GPRS network is connecting

GPSR connection is active

HSDPA network is available

HSDPA network is connecting

HSDPA connection is active

GeoExplorer 6000 Series User Guide 43

Using the Windows Mobile Operating System 3

Pre-installed programs

Programs that are pre-installed on the GeoExplorer 6000 series handheld are as follows:

Interacting with the handheld

To interact with the handheld, use the stylus or your finger to tap items on the touch screen, or to scroll up or down.

If at any time the touch screen does not respond correctly to stylus taps or your finger, realign it. For more information, see Screen, page 50.

Program Function

ActiveSync Synchronize information between the handheld and a computer.

Adobe Reader LE Read PDF documents.

Alarms Set alarms.

Calculator Perform basic arithmetic functions.

Calendar Keep track of appointments and arrange meetings.

Contacts Keep track of your friends and colleagues.

File Explorer View and manage files.

Internet Explorer Browse the World Wide Web.

Email Write, send, and receive email messages.

Messenger Send instant messages using Windows Live

™

Messenger.

Notes Create handwritten, typed, or recorded notes.

Office Mobile 2010 Provides access to these Office Mobile applications: Excel

Mobile

2010, PowerPoint

Mobile 2010, OneNote® Mobile 2010,

SharePoint WorkSpace Mobile 2010, and Word Mobile.

Pictures and Videos Take, view, and edit pictures, or record and launch video clips.

Search Device Search for a file or item stored on the handheld.

Tasks Keep track of your tasks.

Text Send, receive, and organize text messages

Windows Live Access Windows Live services, including email, instant messenger

and Internet search.

Windows Media Play Windows Media

or MP3 audio and video files.

Action Definition

Tap Touch the screen once to open items and select options.

Tap and hold Tap and hold the stylus on an item to see a list of actions available for that

item. On the pop-up menu that appears, tap the action you want to perform.

Drag Hold the stylus on the screen and drag across the screen to select text and

images. Drag in a list to select multiple items.

Flick Flick the stylus or you finger over the screen to scroll a page or a list up or

down.

3 Using the Windows Mobile Operating System

44 GeoExplorer 6000 Series User Guide

The stylus is located on the rear of the handheld. To remove the stylus from its holder, slide the stylus downwards.

To attach a tether to the stylus:

1. Hold the stylus with the Trimble logo facing upwards and insert the end of the tether down through one of the two holes in the top of the stylus and then back up through the other hole.

2. Insert the other end of the tether through the loop and pull until the knot in the tether is tight.

3. Attach the tethered stylus to the handheld as described below.

To attach a tethered stylus to the handheld, feed the end of the tether through the top of the stylus retainer on the rear of the handheld and then feed the end of the stylus through the loop until the knot in the tether is tight.

Entering information

Depending on the program you are using, you can enter information in several ways, as described below:

Input method Description

Synchronizing Use Microsoft connection management software to exchange information

between the handheld and an office computer. For more information, see Chapter 4, Connecting to an Office Computer.

Typing Use the Keyboard input panel to enter typed text by tapping keys on the on-

screen keyboard.

Drawing Use the stylus like a pen to draw (or write) directly on the screen.

Recording Create a stand-alone recording or embed a recording into a note.

GeoExplorer 6000 Series User Guide 45

Using the Windows Mobile Operating System 3

Using the on-screen keyboard

The keyboard button automatically appears in the tile bar of any application.

To display the keyboard, tap the keyboard button, or tap a text box in the application.

To enter characters, use your finger or the stylus to tap the keys on the keyboard. When you finish entering text in a field, tap to accept the text you have entered and then move to the next field.

To enter special characters, tap to display keyboards containing numbers and symbols. To switch back to the main keyboard, tap again.

To hide the keyboard, tap the keyboard icon again.

Tip – To make the keys larger, tap / Settings / Personal / Input. In the Input method list, select Keyboard and then tap Large Keys.

Drawing and writing directly on screen

In some applications, for example Notes, you can draw (or write directly) on the screen using the stylus.

1. Tap and then tap the Notes icon.

2. Tap the Menu icon.

3. Select Draw.

4. Use the stylus to write or draw on the screen.

Textbox

Keyboard button

Keyboard

3 Using the Windows Mobile Operating System

46 GeoExplorer 6000 Series User Guide

Making a recording

You can create a stand-alone voice note or you can add a recording to a note. Then you can work with voice notes in the same way that you work with notes.

To make a recording:

1. Tap

and then tap the Notes icon.

2. Tap the Menu icon.

3. Do one of the following:

– To create a stand-alone recording, in the

screen displaying the list of notes, tap the Record button to begin recording.

– To add a recording to a note, create or open

a note and then tap the Record button to begin recording.

Note – The GeoExplorer 6000 series handheld microphone is on the front of the handheld, in the keypad area. The microphone will capture voice notes when you are holding the handheld in front of you. In noisy environments, you may need to move the handheld closer to you or to the source of the sounds you want to record.

4. When you finish recording, tap the Stop button

If you are creating a stand-alone recording, an icon appears in the note list.

If you are recording in an open note, an icon appears in the note. Tap

OK to return to the note

list.

To play a recording, tap the recording in the note list or open the note and then tap the icon in the note.

Personalizing the handheld

Use the controls in the Settings area to customize the handheld. The following examples describe controls that are available.

Buttons

Use the Buttons control under Personal settings to assign the action you want to be performed when you press the left or right application key.

By default, these keys perform the same action as the left and right tiles in the tile bar. Alternatively, program these keys to perform a selected action.

GeoExplorer 6000 Series User Guide 47

Using the Windows Mobile Operating System 3

Application buttons can be programmed to perform one of the following types of actions:

• Run a selected application, for example Messaging or Calendar.

• Act as a software button, for example an OK/Close button or a scroll button.

• View a selected screen, or part of a screen, for example return to the Home

screen or launch the Context menu or Input panel.

To open the Buttons control:

• Ta p / Settings / Personal / Buttons.

To specify an action for the button:

1. Tap the Program Buttons tab.

2. Tap a button in the list to select it.

3. From the Assign a program drop-down list, select the action you want to occur when you press the button or tap the softkey.

4. Tap

OK.

Home

Use the Home settings to change the display theme that controls the appearance of the Home screen, and to customize how items appear on the Home screen.

Appearance

You can use a theme to customize the background picture on the Home screen, the color of the title and tile bars, menus, and messages.

To change the display theme:

1. Tap / Settings / Home.

2. Tap the Appearance tab.

3. Do one of the following:

– To use a predefined theme, select it from the

list.

– To select the picture that you want to display

in the Home screen background, select the Use this picture as the background check box. Then

tap

Browse to search for a file on the

handheld.

4. Tap

OK.

3 Using the Windows Mobile Operating System

48 GeoExplorer 6000 Series User Guide

Items

You c an choos e betw een:

• the Windows default Home screen view, which allows you to flick through the

list of entries, giving access to functions such as email, text messaging, current time, and Internet Explorer.

• customising which items appear on the Home screen and the order in which

they appear.

To use the default Home screen view:

1. Tap

/ Settings / Home.

2. Tap the Items tab.

3. Select the Windows Default check box.

4. Tap

OK.

To customise the items which appear on the Home screen:

1. Tap / Settings / Home.

2. Tap the Items tab.

3. Select or clear the check boxes to show or hide the Home screen items.

4. Use the

Move Up and Move Down buttons to change where the selected item

appears on the Home screen.

5. Tap

OK.

Set the time and date

1. On the Home screen, tap the clock item, or tap the title bar and then on the pull-down list, tap the clock icon . The Clock & Alarms screen appears.

2. Tap the Time tab.

3. In the Time Zone field, select the required time zone from the dropdown list.

4. In the Date field, tap the down arrow and then select the correct date.

Tip – On the calendar which appears, tap on the month or year to select the required value.

5. In the Time field, tap in turn the hour, minute, and second values and then tap the up or down arrows to set the correct time.

GeoExplorer 6000 Series User Guide 49

Using the Windows Mobile Operating System 3

Device lock

Tap the Device Lock icon on the Start screen to lock the screen and keypad while the handheld remains turned on.

Once the handheld is locked, the screen and most of the keys do not respond until the handheld is unlocked. The exception is the

Power key, which always respond when

pressed.

Communication with external devices such as a GNSS receiver, or external sensors used by GNSS field software, is not interrupted by locking the handheld. This means that you can keep using the GNSS field software when the handheld is locked. For example, you could lock the device so that you can safely transport it between features, while keeping the software connected to the GNSS receiver so that you can continue recording GNSS positions.

The lock screen provides multiple unlock sliders for different applications, when there are new notifications. For example, if a new email has arrived, an email unlock slider takes you straight to the email.

To unlock the device, slide the Unlock icon for the required application to take you straight to that application.

You can help to keep your data secure by requiring a password each time the handheld is turned on. Tap

/ Settings / Lock to set a password or to change password settings.

Power

To open the Power control, do one of the following:

• Tap the title bar of the Home screen or the Start screen, and then tap .

• Ta p / Settings / Power.

Tap the Battery tab to check the battery level (see Checking the level of battery power,

page 28).

Tap the Advanced tab to set the time before the handheld turns off when idle (see

Suspend mode, page 31).

Sounds and notifications

Use the Sounds & Notifications control to set preferences for the speaker volume and system sounds. To open the Sounds & Notifications control:

• Ta p / Settings / Sounds & Notifications.

3 Using the Windows Mobile Operating System

50 GeoExplorer 6000 Series User Guide

To turn on or turn off sounds:

1. Tap the Sounds tab.

2. Select or clear the check boxes to enable or disable categories of sounds.

3. If you select the Screen taps or Hardware buttons check boxes, select the Soft or Loud option to control the volume of the sounds.

4. Tap OK.

You can use predefined schemes to customize sounds, or you can create your own sound schemes.

To specify a sound scheme:

1. Tap the Notifications tab.

2. From the Event drop-down list, select an event.

3. Select the type of notification you want to receive for that event.

4. Tap

OK.

Screen

Use the Screen control to align the touch screen or to change the appearance of text on the screen. To open the Screen control:

• Tap / Settings / System / Screen.

To change the screen settings:

1. Tap the General tab.

2. To change the orientation of the screen, select an option in the Orientation group.

3. To start the alignment sequence for the touch screen, tap

Align Screen.

4. Tap

OK.

Note – To align the screen at any time, press and hold the

Power button for 1 second until the Power menu appears

and then tap .

Using ClearType font smoothing can make text easier to read on the screen.

GeoExplorer 6000 Series User Guide 51

Using the Windows Mobile Operating System 3

To enable ClearType:

1. Tap the ClearType tab and then select the Enable ClearType check box.

2. Tap

OK.

To change the size of text on screen:

1. Tap the Text S ize tab.

2. Tap and drag the slider control to the left to make text smaller, or to the right to make text larger.

The example text below the slider shows how the text will appear on screen.

3. Tap

OK.

Backlight

The backlight makes the screen easier to read in low light, but uses extra power. Use the Backlight control to configure power-saving settings for the backlight. To open the Backlight control:

• Tap / Settings / System / Backlight.

To set the backlight to automatically turn off:

1. To automatically turn off the backlight when the handheld is idle and is using battery power, tap the Battery Power tab. Select the Turn off backlight check box and then select a time from the drop-down list.

3 Using the Windows Mobile Operating System

52 GeoExplorer 6000 Series User Guide

2. To automatically turn off the backlight when the handheld is idle and is using external power, tap the External Power tab. Select the Turn off backlight check box and then select a time from the drop-down list.

3. Tap

OK.

To change the br ightness:

1. Tap the Brightness tab.

2. Tap and drag the Brightness Level slider control to the left to make the backlight darker, or to the right to make the backlight brighter.

3. Tap

OK.

Messaging

Use Messaging to send and receive email messages using the GeoExplorer 6000 series handheld. Messaging is the equivalent of your email Inbox.

To use email, you can do one of the following:

• Synchronize email messages with Microsoft Exchange or Microsoft Outlook

an office computer.

• Send and receive email messages by connecting directly to an email server

through an ISP or a network.

Synchronizing email messages

You can synchronize email messages on the handheld and the computer.

CAUTION – When you delete a message on the handheld, it is deleted from the office computer the next time you synchronize the devices.

GeoExplorer 6000 Series User Guide 53

Using the Windows Mobile Operating System 3

To synchronize email, you must enable Inbox synchronization in the Microsoft ActiveSync technology ( for Windows XP) or the WMDC ( for Windows Vista or Windows 7). For more information, refer to the ActiveSync Help or the WMDC Help on the office computer.

During synchronization:

• Messages are copied from the mail folders of Exchange or Outlook on the office

computer to the Messaging folder on the handheld. By default, you will receive messages from the past 3 days only, the first 100 lines of each message, and file attachments of less than 100 KB in size.

• Email messages in the Outbox folder on the handheld are transferred to

Exchange or Outlook, and then sent from those programs.

• Email messages in subfolders in other email folders in Outlook are synchronized

only if they were selected for synchronization (using ActiveSync technology or the WMDC).

To send and receive email for a synchronized Exchange or Outlook account, connect the handheld to the office computer. Synchronization automatically begins, and the handheld sends and receives email.

Connecting directly to an email server

In addition to synchronizing email messages with an office computer, you can send and receive email messages by connecting to an email server.

Before you can send and receive email, you must create an email account in the Messaging software.

Note – You must set up an Internet connection on the handheld before you can set up and use your email account. For more information, see Connecting to a Wi-Fi access point,

page 85, Connecting to a Bluetooth-enabled device, page 87, or Connecting to a Bluetoothenabled phone for Internet access or real-time corrections (including VRS networks), page 94.

If you need to connect to different mailboxes, set up and name a different service for each connection.

Note – The Messaging software supports only the POP3 and IMAP4 protocols for incoming mail, and SMTP for outgoing mail.

3 Using the Windows Mobile Operating System

54 GeoExplorer 6000 Series User Guide

To set up a mail service:

1. Tap / E-mail.

2. Tap Setup E-mail.

3. Enter the email address for your account.

4. Enter a password. Select Save password if you want the device to remember your password.

5. Tap

Next.

6. To automatically get connection settings for your email account from the Internet, select the check box.

7. Tap

Next.

8. Follow the steps in the Setup wizard. If the connection settings are not automatically downloaded from the Internet, you must enter them using the connection details supplied by your ISP or network administrator.

Note – You cannot change the account name later.

9. Tap

Finish.

10. Tap

OK to download mail immediately.

Tip – To receive TerraSync data files by email, edit the settings for the email account you have set up. To do this, tap Menu and then select Options. In the Accounts tab, tap the e-mail account you want to use to receive TerraSync files. The Email Setup wizard appears. Tap Next until you reach the last page of the wizard. From the Message download limit drop-down list, select Entire message.

When you connect the handheld to the email server, new messages are downloaded to the Messaging folder, messages in the Outbox folder are sent, and messages that have been deleted on the email server are removed from the Messaging folder.

Messages received directly from an email server are linked to the email server rather than an office computer. When you delete a message on the handheld, it is also deleted from the email server the next time you connect the handheld to the email server.

You can work online or offline. When working online, you read and respond to messages while connected to the email server. Messages are sent as soon as you tap

Send, which saves space on the handheld.

When working offline, you can disconnect from the email server after you download new message headers or partial messages and then decide which messages to download completely. The next time you connect, Messaging downloads the complete messages you have marked for retrieval and sends any messages that you have written.

CHAPTER

GeoExplorer 6000 Series User Guide 55

Connecting to an Office Computer 4

In this chapter:

Q Connection management

software

Q Connecting the handheld to a

computer

Q Managing the connection using

the Windows Mobile Device Center

Q Managing the connection using

ActiveSync technology

Q Installing software onto the

handheld

Connect the GeoExplorer 6000 series handheld to an office computer to transfer information, settings, and files from one device to the other, or to install software onto the handheld.

You can connect the handheld to a computer using the USB cable or a Bluetooth wireless link.

To protect your data, Trimble recommends that you regularly copy important data to an office computer.

4 Connecting to an Office Computer

56 GeoExplorer 6000 Series User Guide

Connection management software

To install software onto a device powered by the Windows Mobile operating system, or to copy files between the handheld and a computer, you must connect the device to an office computer. If the computer is running:

• the Windows 7 or Windows Vista

operating system, use the Windows Mobile

Device Center (WMDC) to manage the connection.

• the Windows

XP or 2000 operating system, use ActiveSync technology to

manage the connection.

Note – You must install the Windows Mobile Device Center or ActiveSync technology onto the computer before you connect the handheld.

This connection management software also enables you to synchronize office applications on an office computer with the handheld.

CAUTION – The available space on the handheld is small compared to an office computer. To avoid accidentally synchronizing the handheld with a large amount of data on the office computer, Trimble recommends that you either connect to the handheld without forming a partnership, or that you limit the information types and amount of data that is synchronized.

CAUTION – Synchronizing data is designed to keep the same data on both the office computer and the handheld. Exercise care when resynchronizing applications after deleting data from one computer, as resynchronizing will delete the same information from the other computer.

For more information see one of the following:

• Managing the connection using the Windows Mobile Device Center, page 57

• Managing the connection using ActiveSync technology, page 59.

Installing the Windows Mobile Device Center

The Windows 7 and the Windows Vista operating system include a basic connectivity driver for devices powered by a Windows Mobile operating system. This driver allows you to transfer files from the handheld to an office computer.

To install software onto a device powered by a Windows Mobile operating system, you must install Windows Mobile Device Center 6.1 onto an office computer.

A copy of the Windows Mobile Device Center is provided on the GeoExplorer 6000 Series Getting Started Disc. Alternatively, go to

www.microsoft.com/windowsmobile/devicecenter.mspx to download the latest

version from the Microsoft website.

GeoExplorer 6000 Series User Guide 57

Connecting to an Office Computer 4

Installing ActiveSync technology

A copy of ActiveSync technology is provided on the GeoExplorer 6000 Series Getting Started Disc. Alternatively, go to

www.microsoft.com/windowsmobile/activesync/default.mspx to download the latest

version from the Microsoft website.

Connecting the handheld to a computer

To connect the GeoExplorer 6000 series handheld to a computer:

1. Make sure that the handheld and the computer are switched on.

2. Make sure you have installed the appropriate connection management software onto the computer (see Connection management software, page 56).

3. To form a connection, do one of the following:

– Use the handheld's integrated Bluetooth radio to establish a wireless serial

link to a Bluetooth-enabled computer. For more information, see

Connecting to an office computer using Bluetooth wireless technology, page 104.

– Use a USB connection:

a. Connect the USB data cable to the USB port on the handheld.

b. Connect the other end of the USB data cable to a USB port on the

computer.

When the handheld and the computer are connected, you can manage the connection through a window that appears on the office computer. See one of the following:

– Managing the connection using the Windows Mobile Device Center,

page 57

– Managing the connection using ActiveSync technology, page 59

Managing the connection using the Windows Mobile Device Center

1. Connect the handheld to the computer (see page 57).

2. If the Autoplay window appears, close the window.

4 Connecting to an Office Computer

58 GeoExplorer 6000 Series User Guide

3. The Windows Mobile Device Center window displays the message Connected:

Note – If the connection is not made automatically, check that the connection is enabled in the Windows Mobile Device Center software and on the handheld. For more information, see Troubleshooting, page 117.

4. Do one of the following:

– To synchronize files and data between the handheld and a computer, click

Set up your device and then follow the instructions on screen.

– To transfer data between the handheld and the computer without

synchronizing the devices, click Connect without setting up your device.

5. To transfer files between the computer and the handheld, click File Management. A Windows Explorer-type window appears, displaying files stored on the handheld. Copy and paste files to other locations on the computer, or from the computer to the handheld.

6. To install software onto the handheld, see Installing software onto the handheld,

page 60.

7. To uninstall software from the handheld, click Programs and Services and then click Add/Remove Programs.

Tip – If the Add/Remove Programs option does not appear below Programs and Services, click More. The Add/Remove Programs option appears.

For more information, refer to the Windows Mobile Device Center Help.

Tip – If the GPS Pathfinder® Office software is installed on the office computer, you can configure the Connection Manager utility in the GPS Pathfinder Office software to automatically detect when you connect a GeoExplorer 6000 series handheld to the computer. This enables you to automatically transfer data from the TerraSync software, differentially correct the data, and then export it to a GIS. For more information, refer to the GPS Pathfinder Office Software Help.

GeoExplorer 6000 Series User Guide 59

Connecting to an Office Computer 4

Managing the connection using ActiveSync technology

1. Connect the handheld to the computer (see page 57). The Synchronization Setup Wizard appears:

Note – If the connection is not made automatically, check that the connection is enabled in the ActiveSync technology and on the handheld. For more information, see

Troubleshooting, page 117.

2. Do one of the following:

– To synchronize files and data between the handheld and a computer, click

Next and then follow the instructions in the Synchronization Setup Wizard.

– To transfer data between the handheld and the computer without

synchronizing the devices, click

Cancel to close the wizard.

3. The Microsoft ActiveSync window displays the message

Connected:

4 Connecting to an Office Computer

60 GeoExplorer 6000 Series User Guide

4. To transfer files between the computer and the handheld, click Explore. A Windows Explorer-type window appears, displaying files stored on the handheld. Copy and paste files to other locations on the computer, or from the computer to the handheld.

5. To install software onto the handheld, see Installing software onto the handheld,

page 60.

6. To uninstall software from the handheld, select Add/Remove Programs from the To ol s menu. Clear the check box beside the program you want to remove and then click

OK.

For more information, refer to the ActiveSync Help.

Tip – If the GPS Pathfinder Office software is installed on the office computer, you can configure the Connection Manager utility in the GPS Pathfinder Office software to automatically detect when you connect a GeoExplorer 6000 series handheld to the computer. This enables you to automatically transfer data from the TerraSync software, differentially correct the data, and then export it to a GIS. For more information, refer to the GPS Pathfinder Office Software Help.

Installing software onto the handheld

Before you begin, refer to the installation instructions provided with the software.

Some software installations are specifically designed to run on a device powered by a Windows Mobile operating system. To install software that has a Windows Mobile installation setup:

1. Connect the handheld to a computer (see page 57).

2. Copy the installation files to a folder on the handheld.

3. Browse to the folder on the handheld. Tap and hold the installation setup file and then select Run.

4. If prompted after installation, perform a soft reset of the handheld (see page 33).

To install software that is provided on a CD, or as an installation setup that runs on an office computer:

1. Connect the handheld to a computer (see page 57).

2. If the software is provided on a CD, insert the software CD into the office computer.

3. Run the installation setup.

4. If prompted, select the install option for a device powered by a Windows Mobile operating system. Once the software is installed on the computer, it is automatically transferred to the handheld.

Note – If a storage card is inserted in the handheld, the card appears as an installation location option. Trimble recommends that you install software to the handheld’s internal storage, not to a storage card. If you install software to a card and then remove the card from the handheld, the software will not be available for use.

5. If prompted after installation, perform a soft reset of the handheld (see page 33).

CHAPTER

GeoExplorer 6000 Series User Guide 61

Using the GNSS Receiver 5

In this chapter:

Q Supported GNSS field software

Q Configuring the GNSS field

software to connect to the receiver

Q Using the GNSS field software

Q Improving GNSS productivity

using Floodlight satellite shadow reduction technology

Q Ensuring the accuracy of your

GNSS data

Q Activating the Floodlight

technology and the NMEA output options

Q Differential GNSS explained

Q Outputting NMEA data to

external equipment

Q Configuring NMEA output

The GeoExplorer 6000 series handheld includes an integrated GNSS receiver that enables you to collect GPS and GLONASS data for incorporating into a GIS or for managing assets.

GPS (Global Positioning System) and GLONASS (GLObal NAvigation Satellite System) are Global Navigation Satellite Systems (GNSS). Each system consists of a constellation of satellites that orbit the earth. GNSS provides worldwide, all-weather, 24-hour time and position information.

Note – To receive signals from GPS or GLONASS satellites, the handheld must have a clear view of the sky. GPS or GLONASS positions may not always be available, particularly in or near buildings, in vehicles, or under tree canopy.

With the addition of the Trimble Floodlight satellite shadow reduction technology option, the GeoExplorer 6000 series handheld’s integrated GNSS receiver can improve accuracy and productivity in difficult environments.

Note – To track G LO NASS satel li tes, you mu st have the Trimble Floodlight technology option installed and activated.

5 Using the GNSS Receiver

62 GeoExplorer 6000 Series User Guide

Supported GNSS field software

You can use the GeoExplorer 6000 series handheld with any of the software products described below.

TerraSync software

You can install version 5.10 or later of the TerraSync software on a GeoExplorer 6000 series handheld. Use the software to collect and maintain GIS and GNSS data.

To install the TerraSync software, run the downloaded setup file. To obtain an installation code for installation, you must register the Proof-of-Purchase Number (POPN) that you received when you purchased the software. Detailed installation instructions are provided in the TerraSync Software Getting Started Guide.

Esri ArcPad software and the Trimble GPScorrect extension

You can install the Esri ArcPad software version 10 on a GeoExplorer 6000 series handheld. Use the software to collect and maintain GIS and GNSS data. Detailed installation instructions for Esri ArcPad software are provided in the ArcPad documentation.

To be able to differentially correct ArcPad GNSS data, install version 3.20 or later of the Trimble GPScorrect extension for Esri ArcPad software on a GeoExplorer 6000 series handheld.

You m ust in stall t h e ArcPad softwa re before you install the GPScorrect extension.

Note – Make sure your version of the GPScorrect extension is compatible with the version of ArcPad software you are using. For more information, go to

www.trimble.com/gpscorrect_ts.asp, click Support Notes and then search for the Mapping

and GIS Product Compatibility List Support Note.

To install the GPScorrect extension, run the downloaded setup file. Detailed installation instructions are provided in the Trimble GPScorrect Extension Getting Started Guide.

GPS Controller software

You can install version 2.40 or later of the GPS Controller software on a GeoExplorer 6000 series handheld. Use the software to configure and monitor the status of the internal GNSS receiver, and to configure GNSS output settings for third party GNSS applications.

To install the GPS Controller software, go to www.trimble.com/support.shtml. Click GPS Controller and then click Downloads. Click the link for the version you want to install and then follow the instructions in the Installation wizard.

GeoExplorer 6000 Series User Guide 63

Using the GNSS Receiver 5

GNSS Connector software

You can install the GNSS Connector software on a GeoExplorer 6000 series handheld. Use the software to specify how the integrated GNSS receiver communicates with equipment that is connected to one of the handheld’s external communications ports.

To install the GNSS Connector software, go to www.trimble.com/support.shtml. Click GNSS Connector and then click Downloads. Follow the instructions in the Installation wizard.

Other GNSS field applications

If you have purchased and activated the NMEA Output option, you can also use the GeoExplorer 6000 series handheld with any GNSS field software that accepts NMEA messages.

Configuring the GNSS field software to connect to the receiver

The first time you use GNSS field software on the handheld, you may need to specify which GNSS COM port to connect to.

GNSS COM ports

The integrated GNSS receiver has three COM ports for communicating with software on the handheld and with external devices. Two ports are for outputting GNSS data, and one port is for receiving real-time corrections into the receiver.

To use GNSS, open the appropriate GNSS COM port. The type of communication used for each port is described below:

Note – NMEA messages can only be output if you have purchased and activated the NMEA Output option.

Port Function Description

COM2 NMEA Outputs NMEA-0183 messages. NMEA is a standard GNSS

communication protocol used by many GNSS applications. The handheld outputs the following NMEA messages by default: GGA,

GLL, GSA, GSV, RMC, VTG, ZDA. All messages are output at a onesecond interval.

COM3 TSIP Outputs and receives TSIP messages. TSIP (Trimble Standard Interface

Protocol) is used by Trimble GNSS applications, and is also supported by some other GNSS applications.

COM4 Real-time

corrections

Receives real-time correction messages. If you are using an external correction source connected to COM1 or a Bluetooth port, the corrections must be redirected to COM4. For more information, see

Using real-time corrections from an external correction source, page 70.

5 Using the GNSS Receiver

64 GeoExplorer 6000 Series User Guide

Note – COM1 is a standard serial port that connects to external devices. For more information, see Connecting to other devices using the USB to serial converter, page 111.

Connecting to the COM port

Details of how to configure different types of GNSS field software to connect to the GNSS COM port are as follows:

Using the GNSS field software

Depending on the GNSS field software you have installed, the default GNSS field software will be GPS Controller, TerraSync, or the Trimble GPScorrect extension for Esri ArcPad software.

The GPS Controller software enables you to check the current GNSS status, or to configure the integrated GNSS receiver.

Note – You must first install the GPS Controller software. See GPS Controller software,

page 62 for details.

Depending on the GNSS field software you have installed, you can use the software to configure settings such as GNSS, real-time correction, and antenna settings. You may also be able to use the software to connect to a real-time correction source, configure logging settings, and collect features. For more information, refer to the rest of this chapter and the documentation for the GNSS field software.

GPS field software Configuration details

GPS Controller Run GPS Controller. The software automatically activates the

integrated GNSS receiver on COM3.

TerraSync Run Terrasync. The software automatically activates the integrated

GNSS receiver on COM3.

ArcPad with the GPScorrect extension

When the Trimble GPScorrect extension is installed, the extension automatically configures the ArcPad software to use the integrated GNSS receiver on COM3 using the Trimble GPScorrect protocol.

To connect to the receiver, tap the

GPS button and then tap Yes.

To configure a real-time Differential GNSS source, or to view status information, run the GPScorrect extension. To do this, tap the

GPScorrect button in the Trimble toolbar.

ArcPad without the GPScorrect extension

1. In ArcPad, tap the

GPS drop-down menu and then select

GPS Preferences from the drop-down menu. Tap the GPS tab.

2. In the Protocol field, select NMEA 0183.

3. In the Port field, select COM2.

4. Tap

OK.

5. Tap the

GPS button and then tap Yes.

NMEA application Configure the software to connect to GNSS on COM2 and then use

the Connect or Activate GNSS command.

TSIP application Configure the software to connect to GNSS on COM3 and then use

the Connect or Activate GNSS command.

GeoExplorer 6000 Series User Guide 65

Using the GNSS Receiver 5

Starting the GNSS field software

Do one of the following:

• From the Home screen, tap the GeoXH (or GeoXT) item, then tap the GNSS

Application Launcher item to launch the default GNSS field application.

• Tap / Programs and then select the GNSS field software, for

example TerraS ync.

When you first open any Trimble GNSS field software, the Skyplot section is displayed.

Viewing available GNSS satellites

Use the graphical Skyplot section or the Satellite Info section in the installed Trimble GNSS field software to view detailed GPS and GLONASS information.

Note – To receive signals from GNSS satellites, the handheld must have a clear view of the sky. GNSS positions may not always be available, particularly in or near buildings, in vehicles, or under tree canopy.

Filled (black) boxes represent satellites that the receiver is using to compute its current GNSS position. Unfilled (white) boxes represent satellites that the receiver is getting signals from but is not using because the signals are too weak. In the example shown here, eight satellites are being tracked and seven of these satellites are being used to compute GNSS positions.

Note – Numbers with no box represent satellites that are available, but that the TerraSync software is not receiving signals from. Satellites that have an "R" prefix are GLONASS satellites. GLONASS satellites appear only if the receiver has the Trimble Floodlight satellite shadow reduction technology option activated. For more information, see

Activating the Floodlight technology and the NMEA output options.

Your current GNSS position is displayed at the bottom of the screen.

Tip – For detailed information on satellite positions and signal strengths, use the Satellite information screen in the Status section.

Resetting the GNSS receiver

Trimble GNSS field applications all have options to reset the receiver to:

• delete the almanac

• delete information stored on the last known position

• restart the receiver

• reset the GNSS receiver to factory default settings

5 Using the GNSS Receiver

66 GeoExplorer 6000 Series User Guide

Improving GNSS productivity using Floodlight satellite shadow reduction technology

The productivity of high-accuracy GNSS receivers can be affected by satellite shadow. Satellite shadow occurs when the line of sight between a GNSS receiver and GNSS satellites is partially or fully blocked by obstructions such as buildings, trees, or even the landscape itself. The effect of satellite shadow is a reduction in the number of satellites that the receiver can track. In general, the quality of your data decreases when the number of satellites which is used to calculate the position is low, and in many cases when large portions of the sky are obstructed, it is impossible to generate any positions at all.

The Floodlight satellite shadow reduction technology option for the GeoExplorer 6000 series reduces the effects of satellite shadow to help deliver more positions and better accuracy in conditions affected by satellite shadow.

The Floodlight technology option improves GNSS productivity using three key technologies:

• it enables GLONASS satellite tracking, which greatly increases the number of

satellites that the GNSS receiver can track. Tracking more satellites can help to improve satellite geometry and thereby improve accuracy.

• it utilizes barometric measurements to assist the GNSS receiver. The barometer

measurements can assist by improving both the vertical and horizontal accuracy of positions, particularly in conditions where the satellite count is very low, for example under tree canopy.

• it improves the ability of the receiver to track weaker satellite signals which are

common when working in the shadows of trees and buildings.

To achieve optimum Floodlight technology performance, it is important that the barometer is kept free of obstructions. Make sure that the Barometer seal located on the underside of the device is kept clear and is not covered by your fingers or any other covering.

Note – If you are using Trimble field software, for example, the TerraSync software, make sure that you have selected the correct option for postprocessing data—if your base station(s) provide corrections for GPS and GLONASS satellites, select GPS + GLONASS. This affects the accuracy of the Predicted Postprocessed Accuracy (PPA). See Accuracy settings and

using accuracy-based logging, page 68.

To purchase the Floodlight technology option, contact your Trimble reseller.

After purchase, you must activate the Floodlight technology option on the receiver. See

Activating the Floodlight technology and the NMEA output options, page 74.

Barometer

GeoExplorer 6000 Series User Guide 67

Using the GNSS Receiver 5

Ensuring the accuracy of your GNSS data

GeoExplorer 6000 series handhelds are high performance GNSS receivers that calculate very accurate GNSS positions.

To correct errors in the collected data and to further improve the accuracy of the GNSS positions, use differential GNSS. Differential GNSS (DGNSS) requires one or more additional receivers, called base stations or reference stations, which are located at known points. Data collected at the base stations is used to determine GNSS measurement errors and compute corrections to these errors. These corrections are then applied to data collected in the field either in real time or during postprocessing. For more information, see Differential GNSS explained, page 75.

The different models in the GeoExplorer 6000 series offer two levels of DGNSS accuracy:

• The GeoXT handheld uses EVEREST multipath rejection technology to provide

< 1 meter accuracy with real-time or < 0.5 meters postprocessed differential correction.

• The GeoXH handheld uses EVEREST multipath rejection technology as well as

H-Star technology to provide 10 cm accuracy with real-time or postprocessed differential correction.

For more information, refer to the datasheet for your model of handheld.

Where the DGNSS infrastructure does not meet 10 cm accuracy requirements ( for example, the base station provides L1 corrections only, or is at a distance greater than recommended), the GeoXH handheld typically achieves submeter accuracy.

The list below identifies the most important settings and techniques that you can use in the field to improve the accuracy of your data:

Note – This list assumes that you are using Trimble GNSS field software, and lists items in order of most important to less important.

1. If you are using the TerraSync software to collect data, use accuracy-based logging. For more information, see page 68.

2. Use real-time differential corrections. If you are using a GeoXH handheld and have access to dual-frequency corrections from a VRS

™

network, use the

corrections from the VRS network. For more information, see page 69.

3. Configure the GNSS settings for the receiver to use Smart Settings to increase the precision of your data, and to minimize the effect of atmospheric interference and poor satellite geometry. For more information, see Using Smart

Settings, page 71.

4. Connect to an external antenna, if you have one. For more information, see page 73.

5. Plan GNSS data collection around the times of the day when satellite geometry is best. For more information, see page 74.

5 Using the GNSS Receiver

68 GeoExplorer 6000 Series User Guide

Accuracy settings and using accuracy-based logging

If you are using the TerraSync software, use accuracy-based logging to ensure that only GNSS positions that meet the specified estimated accuracy are logged. GNSS positions that do not meet your accuracy requirements are not logged.

Note – Accuracy estimates for streaming (dynamic) GNSS positions may not be as good as those for static GNSS positions.

To configure accuracy-based logging in the TerraSync software:

1. In the Setup section of the TerraSync software, tap

Logging Settings. The Logging Settings form

appears.

2. Tap the

Setup button below the Accuracy

Settings field. The Accuracy Settings form appears.

3. In the Accuracy Value For Display/Logging fields, select the parameters that will be used to determine the estimated accuracy:

– Select whether to use the horizontal or

vertical accuracy of the current GNSS position.

– Select In the field to use the current

estimated accuracy (recommended if you are using a real-time correction source), or select Postprocessed to use the predicted estimated accuracy that will be achieved after the field data has been postprocessed.

4. If you selected Postprocessed:

a. select the estimated distance to the base station that will be used for

postprocessing from the Postprocessing Base Distance field. If you will use more than one base station (during H-Star processing), specify the estimated distance to the closest base station.

b. select the type of data that your base station(s) will provide to ensure that

PPA (Predicted Postprocessed Accuracy) values can be predicted accurately:

– If your base station(s) are providing corrections for GPS and GLONASS

satellites, select GPS + GLONASS.

– For base stations with only GPS satellite corrections, select GPS.

– If you don't know what base station data you will use, or what base data is

provided by your base stations, select GPS.

5. Set the Use Accuracy-based Logging field to Yes. The settings fields for accuracy-based logging appear.

6. In the Apply Accuracy-based Logging To field, select the feature types that you want to log only if the GNSS positions meet your required accuracy.

GeoExplorer 6000 Series User Guide 69

Using the GNSS Receiver 5

7. In the Required Accuracy field, select the estimated accuracy that is required before GPS positions are logged.

8. Tap

Done.

Note – Accuracy settings do not affect GNSS positions that are used for navigation. GNSS positions are still calculated by the GNSS receiver and are available for navigation.

Connecting to a real-time differential correction source

Use a real-time differential GNSS (DGNSS) source to give you better accuracy as you collect data. For more information about how real-time differential GNSS works, see

Differential GNSS explained, page 75.

Using real-time corrections from an Internet source

DGNSS corrections are often broadcast over the Internet. For example, corrections generated by a VRS network are commonly broadcast over an Internet server. A VRS network uses data from several base stations to provide rover receivers with corrections that are generally more accurate than corrections from a single base station. Alternatively, you can connect to a server that provides DGNSS corrections from a single base station.

For information on how to connect to the Internet and receive real-time corrections from an Internet server, see Connecting to a Bluetooth-enabled device, page 87 or

Connecting to a Bluetooth-enabled phone for Internet access or real-time corrections (including VRS networks), page 94.

Using SBAS corrections

The GeoExplorer 6000 series handheld has an integrated receiver that uses Satellite Based Augmentation Systems (SBAS) correction messages to improve the accuracy and integrity of GNSS data.

The default SBAS tracking mode is Auto. In Auto mode, the receiver tracks or locks onto the most powerful satellite signal. The GNSS receiver can track two SBAS satellites at the same time in Auto or Custom mode. It uses corrections from only one SBAS satellite at a time, but tracking two satellites can improve the availability of SBAS real-time corrections. For example, if you are working in environments where obstacles may block the direct line of sight to the SBAS satellite, there is less chance of signal loss if you are tracking more than one SBAS satellite.

Note – To turn off multiple SBAS satellite tracking, select Custom mode and then deselect all other SBAS satellites except for the satellite you want to track.

The receiver tracks SBAS satellites according to your geographical location:

• Wide Area Augmentation System (WAAS) satellites are tracked in the

Continental United States including Alaska, and parts of Canada and Mexico.

• European Geostationary Navigation Overlay Service (EGNOS) satellites are

tracked in Europe.

5 Using the GNSS Receiver

70 GeoExplorer 6000 Series User Guide

• MTSAT Satellite-based Augmentation System (MSAS) satellites are tracked in

Japan.

To use SBAS corre ctions:

1. In the Setup section of the GNSS software, tap

Real-time Settings. The Real-time Settings form

appears.

2. In the Choice 1 field, select Integrated SBAS.

3. To select particular satellites, tap the

Setup

button next to the Choice 1 field. Select Custom tracking mode and then enable or disable tracking of particular satellites. Tap

OK to return

to the Real-time Settings screen.

4. In the Choice 2 field, specify whether to use uncorrected positions, or to stop using GNSS positions, if corrections are not available.

5. Tap

Done.

Using real-time corrections from an external correction source

You can improve the accuracy of your data by using real-time corrections from an external correction source, such as a GeoBeacon receiver or a DGNSS radio. Connect the external correction source to a Bluetooth port (see page 93). Use the GNSS field software to set up and monitor the real-time input source that you want to use.

The integrated GNSS receiver communicates only through its GNSS COM ports (COM2, COM3, and COM4). Trimble GNSS field software, such as TerraSync and GPS Controller, automatically redirects input from an external correction source connected to COM1 or to a Bluetooth port to the real-time GNSS COM port (COM4).

Note – For information on configuring the GNSS field software to use corrections from a VRS network or single base station that transmits corrections over the Internet, see Step 3:

Configuring the GNSS field software to use data received from the Internet source, page 97.

GeoExplorer 6000 Series User Guide 71

Using the GNSS Receiver 5

To set up an external correction source—such as a GeoBeacon receiver or a DGNSS radio—in the Trimble GNSS field software:

1. In the Setup section of the GNSS software, tap

Real-time Settings. The Real-time Settings form

appears.

2. In the Choice 1 field, select External Source.

3. Tap the

Setup button next to the Choice 1

field.

4. In the Connection Method field, select Serial Port.

5. In the Port field, select the COM port to use. If you are using:

– the USB to serial converter, select COM 1.

– a Bluetooth wireless connection, select the

COM port you configured for the Bluetooth connection in the COM Ports tab of the Bluetooth manager.

6. Tap

Done.

To set up an external correction source for use with non-Trimble GNSS field software:

1. In the Trimble GPS Controller software, configure the GNSS receiver to use real-time corrections on COM4. For more information, see the steps above.

Note – You must first install the GPS Controller software. See GPS Controller software,

page 62 for details.

2. In the GNSS Connector software, manually redirect the real-time correction source to COM4 by tapping

Setup then select the real-time source from the

drop down list.

Note – You must first install the GNSS Connector software. See GNSS Connector software,

page 63 for details.

3. Configure your data collection software to monitor and use real-time corrections as required.

Note – To receive real-time corrections, the GNSS Connector software must remain running on the handheld.

Using Smart Settings

Note – Trimble recommends that you use accuracy-based logging (see Accuracy settings

and using accuracy-based logging, page 68) and Smart Settings to control the quality of the

GNSS positions logged and let the TerraSync software manage the logging of positions based on your required accuracy.

5 Using the GNSS Receiver

72 GeoExplorer 6000 Series User Guide

Using Smart Settings, the GNSS receiver generates the best possible position for any given environment, without the need for you to adjust receiver settings to match the conditions. Regardless of whether you are working under canopy, in wide open spaces, or somewhere in between, Smart Settings automatically generates the best solution possible.

Using traditional mask techniques in open conditions, weak signals can accidentally degrade the accuracy of the position if masks are too relaxed, whereas in obstructed conditions, more satellites are needed to help maintain optimum accuracy if masks are set too strictly. Using Smart Settings, the receiver uses all available GNSS information to determine which combination of satellites to use to deliver the best position. Once you set the receiver to use Smart Settings, the receiver does the rest.

By default, the receiver is configured to use Smart Settings. In this mode, the receiver will track all visible satellites, and determine which to use in the position solution to automatically generate the most accurate position possible.

To open the GNSS Settings form, do one of the following:

• Ta p GNSS Settings in the Setup section.

• Tap in the Skyplot, Satellite Info, or Plan section.

To enable Smart Settings, select the Use Smart Settings check box.

To define custom GNSS settings, clear the Use Smart Settings check box. Editable fields appear enabling you to specify the required GNSS quality settings. Enter values in these fields.

GeoExplorer 6000 Series User Guide 73

Using the GNSS Receiver 5

Connecting to an external antenna

The GeoExplorer 6000 series handheld has an internal antenna, which is suitable for use in most conditions.

If you have a GeoXT handheld, you can also connect a Tempest or an external patch antenna for when you work in a vehicle. For improved yield under canopy, you can use a Tempest antenna, or a patch antenna with a ground plane.

If you have a GeoXH handheld, you can connect an external Tornado antenna for improved accuracy when you collect data for postprocessing using H-Star technology.

Configure antenna settings in the GNSS field software, once you have connected the external antenna to the handheld.

To configure antenna settings in the TerraSync software:

1. In the Setup section of the TerraSync software, tap

Logging Settings. The

Logging Settings form appears.

2. Tap the

Setup button next to the Antenna Height field. The Antenna Settings

form appears.

3. In the Height field, specify the height of the GNSS antenna that is connected to the GNSS position.

4. In the Confirm field, select how often the software will ask you to confirm the configured antenna height during data collection.

5. In the Type field, select the type of antenna that is connected. The number in the Part Number field is automatically updated when you select the antenna type.

6. In the Measure Height To field, select the point on the antenna that you have measured the height to.

7. Tap

OK to return to the Logging Settings form.

5 Using the GNSS Receiver

74 GeoExplorer 6000 Series User Guide

Planning a data collection session

To maximize productivity, plan GNSS data collection around the times of the day when satellite geometry is best. The TerraSync software and the GPS Controller software both include a Plan section with an animated skyplot and DOP (satellite geometry) graph for your position for the next 12 hours.

In the Plan section, you can check the planning skyplot as you play a session, then use the timeline to zoom in on times when geometry is poor. As you adjust GNSS settings, the Plan section is updated, so you can see the effect of different quality control settings.

Activating the Floodlight technology and the NMEA output options

Two options are available for use with the GeoExplorer 6000 series handhelds:

• the Trimble Floodlight satellite shadow reduction technology, which can

increase the accuracy and likelihood of generating positions in environments affected by satellite shadow including canopy and near buildings.

• the NMEA Output option, which enables you to use the GeoExplorer 6000 series

handheld’s integrated GNSS receiver with any GNSS field software that accepts NMEA messages.

The Floodlight satellite shadow reduction technology is provided as standard with the GeoXH handheld.

For the GeoXT handheld, you will need to purchase the Floodlight satellite shadow reduction technology option.

The NMEA option must be purchased for both the GeoXH handheld and the GeoXT handheld if required. Contact you Trimble reseller for more information.

Both the Floodlight satellite shadow reduction technology option and the NMEA Output option must be activated on your handheld using the Option Activation Wizard. The wizard can either automatically retrieve an activation file over the Internet, or you can copy the file manually to the device using an external storage card or a USB cable. The activation wizard uses the file to determine which options to activate on the handheld.

To activate these options using the Option Activation wizard, do the following:

1. Tap / Settings / System / System Information, the System Information screen appears.

2. Select the Options tab and then tap

Activate Options.

3. If you have received an activation file from your Trimble reseller, select Manually activate purchased options. Otherwise select Automatically check and activate purchased options.

GeoExplorer 6000 Series User Guide 75

Using the GNSS Receiver 5

4. Do one of the following:

• If you selected Automatically check and activate purchased options:

a. Ensure that the device is connected to the Internet (using a USB cable and

the ActiveSync technology, or a Wi-Fi connection or Bluetooth wireless connection using the modem—see Chapter 6, Getting Connected).

b. Tap

Get Updates.

c. The Option Activation Wizard will run. When the wizard finishes, restart

your device to complete the activate process.

• If you selected Manually activate purchased options:

a. Copy the activation XML file that you reecieved from your Trimble reseller

to a folder on the device.

b. Tap

Get Updates.

c. Browse to the folder that contains the activation file.

d. Tap the file to initiate the activation process.

e. The Option Activation Wizard will run. When the wizard finishes, restart

your device to complete the activate process.

Differential GNSS explained

Use differential GNSS to correct errors in your collected data. Differential GNSS (DGNSS) requires one or more additional receivers, called base stations or reference stations, which are located at known points. Data collected at the base stations is used to determine GNSS measurement errors and compute corrections to these errors. An unlimited number of mobile GNSS receivers, called rovers, collect GNSS data at unknown locations within the vicinity of the base station. Errors common at both the base station and the rover receiver are corrected with DGNSS either in real time or during postprocessing.

Real-time DGNSS

In real-time DGNSS, the base station calculates and broadcasts the error for each satellite as each measurement is received, enabling you to apply corrections while in the field and collect accurate GNSS data. DGNSS corrections are available from a variety of public and commercial sources. They can be generated and broadcast in real-time by privately or self-owned GNSS base stations, or by a wide range of government agencies.

Real-time DGNSS sources include external beacon and radio sources, as well as Satellite Based Augmentation Systems (SBAS) such as WAAS in the US, EGNOS in Europe, MSAS in Japan, and VRS networks. SBAS and VRS networks use multiple base stations to calculate the DGNSS corrections that are then delivered to the user from a Geostationary satellite (SBAS) or from a radio or cellular phone (VRS networks).

5 Using the GNSS Receiver

76 GeoExplorer 6000 Series User Guide

Factors that affect real-time DGNSS accuracy include how often the corrections are updated, how far you are from the base station, and whether the coordinate system used by the correction source matches the coordinate system used by the GNSS receiver.

Postprocessed DGNSS

In postprocessed DGNSS, the collected GNSS data is transferred to an office computer, and measurements from the base station are downloaded. You can postprocess GNSS data collected with Trimble GNSS field software using:

• the GPS Pathfinder Office software version 5.10 (with the latest updates) or later.

• the Trimble GPS Analyst

™

extension for Esri ArcGIS Desktop software version

2.40 (with the latest updates) or later.

Typically, postprocessed DGNSS uses only one base station. However, when differentially correcting data collected with GeoXH receivers using H-Star technology, you can select multiple base stations to correct the file against for improved accuracy.

Factors that affect the accuracy of postprocessed DGNSS include the type of receiver and antenna used at the base station, the distance between the base station and the location where the rover data was collected, the accuracy of the base station position, and the logging interval at the base station.

For more information, refer to the documentation provided with the postprocessing software.

Postprocessed real-time DGNSS

If you collected data with 10 cm accuracy in real time, you do not need to postprocess the data.

However, if your data files contain autonomous (uncorrected) positions as well as real-time corrected positions, Trimble recommends that you postprocess the data. During postprocessing, you can choose whether to correct only autonomous positions, or all positions.

If you collected data with submeter accuracy in real time, Trimble recommends that you postprocess the data, as postprocessed data is usually more accurate than data corrected in real time.

Outputting NMEA data to external equipment

Use the GNSS Connector software to specify how the integrated GNSS receiver communicates with equipment that is connected to one of the handheld’s external communications ports.

Note – You must first install the GNSS Connector software. See GNSS Connector software,

page 63 for details.

To open GNSS Connector, tap / GNSS Connector.

GeoExplorer 6000 Series User Guide 77

Using the GNSS Receiver 5

The GNSS Connector software lets you connect the NMEA GNSS COM port to COM1 or Bluetooth ports and configure port settings such as the baud rate for COM1.

Use the GNSS Connector software to output NMEA messages from the integrated GNSS receiver to another device, such as an external data collector.

Note – If you are using a Bluetooth port, ensure that the Bluetooth radio is on and the handheld is visible to other devices. Use the GNSS Connector software to configure NMEA output to Bluetooth - COM9, which is the pre-defined Bluetooth Host Serial Port. For more information, see Providing Bluetooth services as a host, page 89.

The connections that you create in the GNSS Connector software are active only while the software is running. Connections created by the GNSS Connector end when you exit the software.

For more information, go to www.trimble.com/support.shtml and refer to the GNSS Connector Help. Click GNSS Connector and then click Help.

Configuring NMEA output

You can use the GeoExplorer 6000 series handheld's integrated GNSS receiver with any GNSS field software that accepts NMEA messages, if you have purchased the NMEA output option and it has been activated on the handheld.

To configure the NMEA data output settings, use the GPS Controller software. The software is provided free from the Trimble website. For more information, see GPS

Controller software, page 62.

To configure NMEA data output:

1. In the GNSS Settings form, set the NMEA Output field to On.

2. Tap the

Setup button that appears next to the

NMEA Output field. The NMEA Output Settings appears.

3. Configure the NMEA message output settings.

CAUTION – NMEA standard dictates that a baud rate of 4800bps should be used for NMEA messages. Depending on the number of satellites being tracked (for example, if you are tracking GLONASS and GPS satellites) the amount of data being captured at once may often cause the 4800 bit limit to be exceeded. Buffers have been added which allow the data to be stored and then sent when it is able to. This avoids data corruption, but may delay delivery of data, and positions may take as long as 8 seconds to be sent from the time at which they were originally recorded. If you need 4800bps output, Trimble suggests that you try to minimise the effect by reducing the amount of NMEA data being sent, for example, by dropping out NMEA sentences from the NMEA stream.

4. Tap Done.

For more information, refer to the GPS Controller Help.

5 Using the GNSS Receiver

78 GeoExplorer 6000 Series User Guide

CHAPTER

GeoExplorer 6000 Series User Guide 79

Getting Connected 6

In this chapter:

Q Wireless connection information

Q Connecting to a cellular network

from the modem

Q Connecting to a Wi-Fi access

point

Q Connecting to a Bluetooth-

enabled device

Q Connecting to other devices using

the USB to serial converter

The GeoExplorer 6000 series handhelds include a number of options for connecting to other devices. For wireless connections to networks or other devices, the options are:

• a 3.5G capable cellular modem (available

on 3.5G editions only)

• an 802.11 b/g compatible Wi-Fi radio

• a Bluetooth radio

You can also connect to other devices using the USB to serial converter.

This chapter describes how to enable the wireless radios, and the main connectivity options available.

Use the table on page 83 to identify the wireless connection type you want to make and then follow the steps provided to connect to that device.

6 Getting Connected

80 GeoExplorer 6000 Series User Guide

Wireless connection information

The GeoExplorer 6000 series handheld has an integrated Wi-Fi radio compliant with IEEE 802.11 b/g, and an integrated Bluetooth radio. 3.5G editions are also equipped with an integrated cellular modem. The handheld is shipped with Wi-Fi and Bluetooth wireless technology activated. To use Wi-Fi, the Bluetooth radio, or the cellular modem you need to turn it on (see Turning on and turning off the integrated radios below).

Note – The integrated cellular modem is only installed on handheld models 88951-00 and 88951-20.

Note – You may need to deactivate the Wi-Fi and/or Bluetooth radio in the handheld (see below) if the country in which you are working does not approve the use of Wi-Fi and/or Bluetooth wireless technology.

Using a data connection from your local cellular provider, the GeoExplorer 6000 series handheld's integrated cellular modem can be used to connect to the Internet to receive real-time corrections from a VRS network, send and receive messages (including email, SMS, or instant messages), or to send and receive files and other data to and from the office directly in the field.

You can also use the handheld’s integrated Wi-Fi radio to connect to the Internet or a corporate network using a Wi-Fi connection.

Alternatively, you can use Bluetooth wireless technology to connect to the Internet using a cellular phone. You can also connect directly to other Bluetooth-enabled devices such as a GeoBeacon receiver, a laser rangefinder, or a barcode scanner.

You can also use the optional USB to serial converter to connect to a range of external devices using a cabled serial connection.

Deactivating the integrated radios

Note – If you are unsure about whether the GeoExplorer 6000 series handheld radios are approved for use in your country, check with your Trimble reseller.

The latest copy of the software is available for download from the Trimble website. Go to www.trimble.com/support.shtml, click the link for your receiver type (GeoXH, or

GeoXT), click Downloads, click GeoExplorer 6000 Series and then click Radio Activation Manager.

Turning on and turning off the integrated radios

You can use the Wireless Manager application to turn on and turn off the GeoExplorer 6000 series handheld's Wi-Fi, Bluetooth, and / or cellular modem radio (see Using the

Wireless Manager, page 81).

GeoExplorer 6000 Series User Guide 81

Getting Connected 6

You can also turn on or turn off the Bluetooth radio from within the Bluetooth application (see Turning on and turning off the Bluetooth radio from within the

Bluetooth application, page 82).

To make the GeoExplorer 6000 series handheld visible to other Bluetooth-enabled devices and enable them to connect, see Making the handheld visible (discoverable) to

other Bluetooth devices, page 82.

Using the Wireless Manager

You can use the Wireless Manager application to turn on and turn off the GeoExplorer 6000 series handheld's Wi-Fi, Bluetooth, and / or cellular modem radio. You can turn on and turn off all radios at the same time, or control each radio individually.

To open the Wireless Manager, do one of the following:

• Tap the title bar, tap any of the radio icons and then tap Wireless Manager.

• Tap / Settings / Connections / Wireless Manager.

Turn on the Wi-Fi, Bluetooth, and / or cellular modem radio to be able to connect to other devices or networks.

Turn off the Wi-Fi, Bluetooth, and / or cellular modem radio to prevent the handheld from sending or receiving wireless signals.

Tip – To conserve power, turn off the Wi-Fi, Bluetooth, and / or cellular modem radio when not in use.

CAUTION – The Bluetooth and cellular modem radios remain active even when the device is in Suspend mode. Turn off the radios when they are not in use.

To turn on or turn off the radios using the Wireless Manager

1. Open the Wireless Manager (see above).

2. Do one of the following:

– Ta p All at the top of the screen to turn on all

radios, or to turn off all radios if they are already on.

– Ta p Wi-Fi, Bluetooth, or Phone to turn on

the radio that you want to use, or to turn off the radio if it is already on.

The status fields below the

Wi-Fi button, the

Bluetooth button, and the Phone button change

from Off when the radios are turned on and show the current state of the radio. The Wi-Fi status field shows Connecting or Available, the Bluetooth status field shows On or Visible, and the

Phone status field shows On or the name of the cellular network

that you are connected to.

6 Getting Connected

82 GeoExplorer 6000 Series User Guide

3. Tap to exit the Wireless Manager.

After you turn on the Wi-Fi radio, the Wi-Fi icon appears in the title bar to indicate that the Wi-Fi radio is enabled. A second icon appears if a Wi-Fi network is detected, and a notification for the detected network may appear in the left softkey.

Turning on and turning off the Bluetooth radio from within the Bluetooth application

1. Tap / Settings / Bluetooth.

2. Tap the Mode tab.

3. Select the Turn on Bluetooth check box to turn on the radio, or clear this check box to turn off the radio.

4. Tap

OK.

Note – If the integrated Bluetooth radio is deactivated, the message

Problem with Bluetooth hardware may appear

when you try to turn on the Bluetooth radio or discover devices.

Making the handheld visible (discoverable) to other Bluetooth devices

To allow other Bluetooth-enabled devices to connect to the GeoExplorer 6000 series handheld, or if the handheld will not connect to or pair with another device you are attempting to connect to, you must make the handheld visible (this is sometimes referred to as “discoverable”).

To make t h e handheld visible to other devices:

1. Tap / Settings / Bluetooth.

2. Tap the Mode tab.

3. Select the Turn on Bluetooth check box, if it is not already selected. This enables the integrated Bluetooth radio.

4. Select the Make this device visible to other devices check box.

5. Tap

OK.

Connecting wirelessly to other devices and networks

You can use a connection to a cellular network using the integrated cellular modem, or a connection to a Wi-Fi access point using the integrated Wi-Fi radio, to connect to the Internet (at broadband speeds) or a corporate network to:

• browse the Internet or an Intranet and send and receive data ( for example, to

obtain real-time corrections from a VRS network)

GeoExplorer 6000 Series User Guide 83

Getting Connected 6

• send and receive messages ( for example, email, instant messages, or SMS

messages)

• access files on the network

Wi-Fi access points are also known as “hotspots”.

You can use Bluetooth wireless technology to connect to other Bluetooth-enabled devices that are within range (typically within 5 m to 10 m of the handheld). You can connect to:

• Bluetooth-enabled devices such as cellular phones to access the Internet and

receive data ( for example, to obtain real-time corrections from a VRS network)

• computers and other handheld devices to exchange files

• other devices such as a GeoBeacon receiver, laser rangefinder, or barcode

scanner

Note – For information on connecting to external devices using the optional USB to serial converter, see Connecting to other devices using the USB to serial converter, page 111

The following table lists devices you can connect to using the handheld, and where to find detailed information on how to achieve these connections.

Connection method To... See...

Cellular modem Connect to a cellular network page 84

Wi-Fi Connect to a Wi-Fi access point page 85

Bluetooth wireless technology Connect to another Bluetooth-enabled device

(paired and non-paired connections)

page 87

Connect to a Bluetooth-enabled phone for Internet access or real-time corrections (including VRS networks)

page 94

Connect to a Bluetooth-enabled serial device page 101

Connect to an office computer to use ActiveSync technology / WMDC

page 104

Output GNSS data to other devices using Bluetooth wireless technology

page 107

Enable other devices to transfer files using Bluetooth wireless technology

page 108

Beam files to or from another device page 109

Wi-Fi, Bluetooth wireless technology, or cellular modem

Access a corporate network through your Internet connection

page 110

6 Getting Connected

84 GeoExplorer 6000 Series User Guide

Connecting to a cellular network from the modem

If your handheld is fitted with the optional cellular modem, use it to establish a connection to a cellular network.

Use this type of connection to browse the Internet or an Intranet and send and receive data ( for example, to obtain real-time corrections from a VRS network), send and receive messages (for example, email, instant messages, or SMS messages), or access files on a corporate network.

Note – The GeoExplorer 6000 series' cellular modem can only be used to send and receive data or text SMS messages. It does not support voice call functionality or sending and receiving MMS messages. Trimble recommends that you request a data-only plan from your cellular service provider and have a 'voice-restriction' placed on your line.

To connect to a cellular network:

1. Configure the connection to the network. This can be Automatic or Manual.

2. Connect to the cellular network.

Before you begin the steps below, Trimble recommends that you:

• make sure that a SIM card is inserted in the handheld. See Installing and

removing a SIM card, page 37.

• confirm that the modem can access the Internet directly. If necessary, contact

your service provicer and confirm whether you must enter a user name, password, and domain details when connecting.

• make sure that you have the correct APN (Access Point Name) from your

cellular provider.

Step 1: Configure the connection

To set up an automatic configuration

1. Tap / Settings / Connections / Wireless Manager. If the Phone is Off, tap Phone to turn it on.

2. Tap / Settings / Connections / Connections.

3. On the Connections screen, on the Tasks tab, tap Automatically configure connection.

The device holds a database of the most common cellular providers and the correct connection settings. The handheld will attempt to identify the SIM vendor.

4. If the SIM vendor is recognised correctly, tap

Next to continue. The connection

settings are set up automatically. The process takes about 30 seconds.

If the SIM is not automatically detected, or the vendor settings are not known you will need to set up the configuration manually. Go to To set up a manual

configuration below.

GeoExplorer 6000 Series User Guide 85

Getting Connected 6

To set up a manual configuration

1. Tap / Settings / Connections / Wireless Manager. If the Phone is Off, tap Phone to turn it on.

2. Tap / Settings / Connections / Connections.

3. Under Tasks, tap Add a new modem connection.

4. Enter a name for the connection, for example

My Connection.

5. In the Select a modem field, select Cellular Line (WWAN) and then tap Next.

6. Enter the APN provided by your cellular provider (check with your provider first for correct settings, some providers have multiple APN settings).

7. Tap

Next.

8. Enter a username password and domain if required (check with your provider, these are often not required). If not required, leave these fields empty.

9. Tap

Finished.

Step 2: Connect to the cellular network:

1. Tap / Settings / Connections / Wireless Manager. If the Phone is Off, tap Phone to turn it on.

2. Tap / Settings / Connections / Connections.

3. Under Tasks, tap Manage existing connections. The configured connections are listed.

4. Tap and hold the connection that you want to use. Tap Connect from the pop-up menu.

The task bar shows the “connecting” icon, for example . When the connection is open/established, the task bar shows the “connected” icon, for example . The icons shown depend on the network—see Network and

modem status indicators, page 42 for full details.

Once connected, open an application, for example, Internet Explorer, to test the connection. Some applications automatically launch the connection when you start the application, if a current connection is not already established.

Connecting to a Wi-Fi access point

To connect to a Wi-Fi access point, you must:

1. Set up the Wi-Fi connection.

2. Connect to the Wi-Fi network or access point.

Note – If you have installed a personal certificate on the handheld, you do not need to set up the wireless connection manually as described in Step 1. To connect to the network or access point go to Step 2: Connecting to the network or access point.

6 Getting Connected

86 GeoExplorer 6000 Series User Guide

Step 1: Setting up the Wi-Fi connection

1. Make sure that the GeoExplorer 6000 series handheld’s Wi-Fi radio is enabled (see page 80).

2. Tap / Settings / Connections / Wireless Manager.

3. Tap

Menu and then select Wi-Fi Settings..

Any networks that you have already configured are displayed in the list of preferred networks.

4. To add a new network, tap Add New. To change the settings for an existing network, tap the network.

5. Enter the name of the network and other connection details and then tap

Next.

6. Do one of the following

– To use authentication, select the

authentication method from the Authentication list.

– To use data encryption, select an encryption method from the Data

encryption list.

– To automatically use a network key, select the check box for The key is

automatically provided. Otherwise, enter the Network key and the Key index.

7. Tap

Next.

8. For increased security, select the Use IEEE 802.1x network access control check box and then configure additional authentication information.

9. Tap

Finish.

Step 2: Connecting to the network or access point

1. Disconnect the USB data cable, as the handheld prioritizes a USB connection over a Wi-Fi connection.

2. Bring the handheld within range of the network or access point.

When a Wi-Fi connectionis detected, the access point icon

appears on the

title bar, and a notification message appears on the left softkey.

If the access point icon or the notification does not appear, use the Wireless Manager to turn off and then turn back on the Wi-Fi radio. When the Wi-Fi radio is turned on, any networks or access points within range are detected and the icon and notification appear.

3. Tap the access point icon on the title bar or tap

Notification on the left softkey.

A popup message shows the available networks.

4. Select the network you want to connect to and then tap

OK on the left softkey.

GeoExplorer 6000 Series User Guide 87

Getting Connected 6

5. Select The Internet (or work via a VPN) or Work and then tap Connect on the left softkey.

6. If a Network Log On screen appears, enter your user name, password, and domain information and then tap

OK on the left softkey.

When the handheld is connected to the network or access point, the Wi-Fi connected icon appears in the title bar.

7. Start using the program you want to use, for example Windows Explorer Mobile or Internet Explorer.

Note – To disconnect from the network or an access point at any time, turn off the handheld’s wireless radio. To do this, tap title bar, tap the Connectivity icon

on the pull-

down list, select Wireless Manager and then tap the

Wi-Fi button.

Tip – To delete a Wi-Fi connection, tap and hold the connection in the Wireless tab of the Wi-Fi Settings screen and then select Remove Settings.

Connecting to a Bluetooth-enabled device

The GeoExplorer 6000 series handheld has an integrated Bluetooth radio that you can use to establish a wireless connection to other Bluetooth devices that are within range.

Using a Bluetooth connection, you can communicate with devices such as cellular phones, office computers, other handhelds, and Bluetooth-enabled laser rangefinders and barcode scanners. You can also communicate with peripheral devices that use Bluetooth adaptors instead of serial or USB connections.

The GeoExplorer 6000 series handheld can act as a Bluetooth client device or a Bluetooth host device, and can act as both at the same time. The concepts of client and host devices are explained in detail below.

Connecting to a Bluetooth device as a client

You can use the GeoExplorer 6000 series handheld as a client device, which uses services offered by Bluetooth host devices that are within range. In general the host

device provides information to the client device, but in some cases the client initiates the connection and also provides information to the host device.

The services used by a GeoExplorer 6000 series handheld when connecting as a Bluetooth client are:

Service Description

Dialup Networking (DUN)

Connects the handheld to a cellular phone or modem for dial-up network or Internet access.

Personal Area Networking (PAN)

Connects to Bluetooth network access points or phones that support the Personal Area Network/Network Access (PAN) profile.

The PAN service is only available on GeoExplorer 6000 series handheld models which do not have an integrated modem.

Serial Port Emulates an RS-232 serial (COM) port on the handheld.

6 Getting Connected

88 GeoExplorer 6000 Series User Guide

A client can connect to a number of different services provided by different hosts. The number of active connections at any one time affects the speed of the connections.

Figure 6.1 shows the handheld connected to different types of host devices using

Bluetooth wireless technology.

Figure 6.1 GeoExplorer 6000 series handheld Bluetooth client connections

In Figure 6.1, the dashed arrows indicate the client device—that is, the GeoExplorer 6000 series handheld—connecting to host devices. The Bluetooth profile (or service) used for the connection is shown between the arrows, for example, the DUN service is used for a connection to a cell phone, and the Serial Port service is used for a serial connection to a GeoBeacon receiver or laser rangefinder.

The solid arrows indicate the flow of information between devices. For example, when the GeoExplorer 6000 series handheld connects as a client to:

• a cellphone, the handheld uses the DUN or PAN host service provided by the

phone to access the Internet and receive real-time differential corrections or background map data.

ActiveSync Enables an ActiveSync connection to a computer.

This service is also used for office computers which have the WMDC installed.

Input Device (HID) Connects the handheld to a physical input device, such as a keyboard.

Wireless Stereo Connects to Bluetooth A2DP (Advanced Audio Distribution Profile)

headphones.

Service Description

GeoExplorer 6000 Series User Guide 89

Getting Connected 6

• a laptop computer or office computer, the devices use the ActiveSync

technology to exchange information to and from either device.

• Bluetooth headphones, the handheld uses the Wireless Stereo host service

provided by the headphones to play audio files and system sounds.

Providing Bluetooth services as a host

You can use the GeoExplorer 6000 series handheld as a Bluetooth host device, which provides services to Bluetooth client devices that are within range.

Host services provided by the GeoExplorer 6000 series handheld are:

To provide a host service, you must turn on the Bluetooth radio and make both devices visible to other devices (see page 80 and page 82).

Figure 6.2 shows different client devices connecting to the handheld using Bluetooth

wireless technology.

Service Description

Serial Port Emulates an RS-232 serial (COM) port on the handheld. For more

information, see Outputting GNSS data to other devices using Bluetooth

wireless technology.

File Transfer Allows a client to browse, copy, paste, and delete files and folders on the

handheld.

Note – You cannot transfer files between two GeoExplorer 6000 series handhelds, as the client file transfer profile is not supported. The handheld supports file transfers as a host device only. To transfer files between handhelds, you can beam them (see page 109).

6 Getting Connected

90 GeoExplorer 6000 Series User Guide

Figure 6.2 GeoExplorer 6000 series handheld Bluetooth host connections

In Figure 6.2 the dashed arrows indicate the client devices—for example, the laptop or PDA—connecting to the GeoExplorer 6000 series handheld, which is the host device. The Bluetooth profile (or service) used for the connection is shown between the arrows, for example the Serial Port service is used when outputting GPS data from the handheld to another device.

The solid arrows indicate the flow of information between devices. The GeoExplorer 6000 series handheld can output GNSS data to client devices that connect to the handheld using a Bluetooth serial port. When a laptop computer or office computer connects to the GeoExplorer 6000 series handheld and selects the File Transfer service, files and information can be exchanged to and from either device.

When a client device connects to the Serial Port service provided by the GeoExplorer 6000 series handheld, applications on the handheld can use the pre-defined host serial port on COM9 to provide host services to the client device. For example, to provide GNSS positions from the integrated GNSS receiver to another device, use the GNSS Connector software to redirect the NMEA output to COM9.

GeoExplorer 6000 Series User Guide 91

Getting Connected 6

Setting up a Bluetooth connection

To use another Bluetooth-enabled device with the GeoExplorer 6000 series handheld, you must form a Bluetooth connection between the two devices, during which you select the type of service to use for the connection. This defines how the devices will communicate with each other.

After forming the Bluetooth connection between the devices you may need to configure settings for the connection such as the COM port for the field software to use, or the number for the phone to dial. You must then connect to the other device using the appropriate software application.

To connect the GeoExplorer 6000 series handheld to another Bluetooth-enabled device, you can use either a paired connection or a non-paired connection.

Note – If you are connecting to a phone, skip this section and go to Connecting to a

Bluetooth-enabled phone for Internet access or real-time corrections (including VRS networks) on page 94, where the pairing step is described as part of the procedure for

connecting to a phone.

Trimble recommends using a paired connection, if pairing is supported by the other device, as a paired connection creates a more secure connection and makes reconnecting to the device easier. For more information, see Pairing with a Bluetooth-

enabled device below.

Some devices, such as a Trimble GeoBeacon receiver, do not support paired connections. Use a non-paired connection if the device does not have a keyboard, and if you know that the device does not automatically exchange a pre-programmed passkey during pairing. For more information, see Setting up a connection to a non-

paired device, page 93.

Pairing with a Bluetooth-enabled device

Pairing the handheld with another Bluetooth-enabled device creates a permanent security bond between the devices, which helps to exchange information securely between the devices. The paired relationship is established when two devices create and exchange a link key. Once the relationship is established, the handheld and the other Bluetooth device only need to have their Bluetooth radios turned on to exchange information; they do not need to be visible to other devices.

To pair with a Bluetooth device:

1. Make sure that the handheld and the Bluetooth device you want to pair with are within five meters of each other, and that the Bluetooth radio in each device is turned on.

2. On the GeoExplorer 6000 series handheld, tap

/ Settings / Bluetooth.

6 Getting Connected

92 GeoExplorer 6000 Series User Guide

3. In the Devices tab, tap Add new device. The handheld searches for other Bluetooth devices and displays them in the list.

If the device you are trying to connect is not displayed in the list, ensure that the device is on and within range and then tap

Retry to search for

devices again.

4. Tap the name of the device you want to pair with and then tap

Next.

5. In the Passcode field, enter a passcode of between 1 and 16 characters. If you are connecting to:

– a device with a keypad, enter a passcode of

your choice.

– a device without a keypad, but you know that the device has a

pre-programmed passcode that will be exchanged, enter that passcode on the GeoExplorer 6000 series handheld.

Note – Trimble recommends that you enter only numbers, as some devices do not support passcodes that include letters.

6. Tap

Next.

7. When prompted, enter the same passcode on the other device.

8. On the handheld, tap the name of other device. The Partnership Settings screen appears.

9. If required, change the name of the device in the Display Name field.

10. Select the service(s) you want to use with this device. For example, if you are connecting to:

– a Bluetooth-enabled phone to connect to the Internet and receive real-time

corrections or download background maps, select Dialup Networking (DUN).

– a serial device, such as a GeoBeacon receiver or a laser rangefinder, select

Serial Port.

– a computer to access ActiveSync technology (or WMDC), select

ActiveSync.

Note – Only ActiveSync shows on the Windows Mobile device. Select ActiveSync even if

you use the WMDC on the desktop computer.

Note – For more information on the types of devices that the GeoExplorer 6000 series handheld can connect to, and the supported Bluetooth services, see Connecting to a

Bluetooth device as a client, page 87.

11. Tap

Save.

12. Tap

OK to close the Bluetooth application.

GeoExplorer 6000 Series User Guide 93

Getting Connected 6

13. Tap to close the Settings screen.

You have now created a partnership between the GeoExplorer 6000 handheld and the other Bluetooth-enabled device so that they can communicate. To start using the connection, you must complete the configuration steps for that type of connection and then connect to the device. For more information, see:

• Connecting to a Bluetooth-enabled phone for Internet access or real-time

corrections (including VRS networks), page 94

• Connecting to a Bluetooth-enabled serial device, page 101

• Connecting to an office computer using Bluetooth wireless technology, page 104

Tip – You only need to pair the handheld with a device before you connect to the device for the first time.

Setting up a connection to a non-paired device

Setting up a connection to a non-paired device enables you to connect to a device that does not allow you to enter a passcode on the device, or that does not automatically exchange a pre-programmed passkey during pairing.

To set up a non-paired connection to a Bluetooth-enabled device:

1. Make sure that the handheld and the Bluetooth device you want to connect to are within five meters of each other, and that the Bluetooth radio in each device is turned on.

2. Tap

/ Settings / Bluetooth.

3. In the Devices tab, tap Add new device. The handheld searches for other Bluetooth devices and displays them in the list.

4. Tap the name of the device you want to connect to and then tap

Next.

The Enter Passcode screen appears.

5. Tap

Next without entering a passcode.

6. If prompted to add the device to your device list, tap

No.

7. On the handheld, tap the name of the other device. The Partnership Settings screen appears.

8. If required, change the name of the device in the Display Name field.

9. Select the service(s) you want to use with this device. For example, if you are connecting to:

– a Bluetooth-enabled phone to connect to the Internet and receive real-time

corrections or download background maps, select Dialup Networking (DUN).

6 Getting Connected

94 GeoExplorer 6000 Series User Guide

– a serial device, such as a GeoBeacon receiver or a laser rangefinder, select

Serial Port.

– a computer to access ActiveSync (or WMDC), select ActiveSync.

Note – Only ActiveSync shows on the Windows Mobile device. Select ActiveSync even if

you use the WMDC on the desktop computer.

Note – For more information on the types of devices that the GeoExplorer 6000 series handheld can connect to, and the supported Bluetooth services, see Connecting to a

Bluetooth device as a client, page 87.

10. Tap

Finish.

11. Tap

OK to close the Bluetooth application.

12. Tap to close the Settings screen.

• Connecting to a Bluetooth-enabled phone for Internet access or real-time

corrections (including VRS networks), page 94

• Connecting to a Bluetooth-enabled serial device, page 101

• Connecting to an office computer using Bluetooth wireless technology, page 104

Connecting to a Bluetooth-enabled phone for Internet access or real-time corrections (including VRS networks)

If your GeoExplorer 6000 series handheld does not include the integrated cellular modem, you can still connect to a cellular network using the Bluetooth radio to connect to a Bluetooth-enabled cellular phone. Use this type of connection to access a VRS network or other correction source from the Internet, a background map server, or for Internet and email access.

Note – Some cellular phones support the Bluetooth PAN (Personal Area Networking) service as well as the Bluetooth DUN (Dialup Networking) service. Because DUN connections are more common, this section assumes you are making a dialup network connection with the Bluetooth-enabled phone. For information on setting up a PAN service, see Connecting to the Internet through a Bluetooth-enabled phone using the Bluetooth PAN

profile, page 100.

To connect to a Bluetooth-enabled phone using a Bluetooth DUN (Dialup Networking) connection, you must:

1. Connect the GeoExplorer 6000 series handheld to a Bluetooth-enabled phone and then configure the connection to the dialup network.

2. Connect to the Internet using the dialup network.

GeoExplorer 6000 Series User Guide 95

Getting Connected 6

3. Configure the software to use the connection. For example, you must configure the GNSS field software to use real-time corrections or map data received from the Internet source, or you must set up the Messaging application to send and receive email using the connection.

Note – Before you begin the steps below, Trimble recommends that you confirm that the phone can access the Internet directly. If necessary, contact the cellular phone provider and confirm whether you must enter a user name, password, and domain details when connecting an external device to the phone using Bluetooth dialup networking.

Step 1: Connecting the handheld to the phone and configuring the connection to the dialup network

1. Make sure that the handheld and the Bluetooth device you want to connect to are within five meters of each other, and that the Bluetooth radio in each device is turned on. For more information, see Turning on and turning off the

integrated radios, page 80.

2. On the handheld, tap / Settings / Connections / Connections.

3. Below My ISP, tap Add a new modem connection.

4. Enter the name for the connection. For example, enter the name of the phone or the VRS network that you will connect to.

5. From the Select a Modem dropdown list, select Bluetooth and then tap

Next.

6. If the phone you want to connect to is:

– listed, go to Step 7 below.

– not listed:

a. Tap Add new device. The handheld

searches for other Bluetooth devices and displays them in the list.

If the handheld’s integrated Bluetooth radio is turned off, it is now automatically turned on.

b. From the list of available devices, select the device you want to connect

to and then tap

Next.

c. To pair with the phone, enter a passcode of your choice that you will

easily remember onto the handheld and then tap

Next.

d. When prompted by the phone, enter the same password and then

accept the connection.

e. On the GeoExplorer 6000 series handheld, tap Advanced to open the

Partnership Settings screen. Make sure that Dialup Networking (DUN) is selected and then tap

Save.

6 Getting Connected

96 GeoExplorer 6000 Series User Guide

You have now created a partnership between the GeoExplorer 6000 series handheld and the phone so that they can communicate.

7. From the My Connections list, select the phone that you want to configure the connection to.

8. Enter the GPRS access number for the Internet.

Two of the common GPRS access numbers for cellular phones on GSM networks are *99***1# and *99#. If these access numbers do not work, contact the cellular phone provider to obtain the appropriate number to use.

Note – You do not need to set up dialling rules or change the Internet connection settings on the phone. The connection settings you enter on the handheld are passed to the phone to use for this connection.

9. Tap

Next.

10. Unless the phone provider confirmed that you must enter user name, password, and domain settings to access the Internet, tap

Finish without entering any

information in this screen.

Otherwise:

a. Enter the required information.

b. If the phone provider has told you that you need to change the baud rate or

other settings for the connection, tap

Advanced, configure these settings

and then tap

OK.

c. Tap

Finish .

You are returned to the Connections screen.

You have now configured the dialup networking connection.

Step 2: Connecting to the Internet using the dialup network

1. On the handheld, go to the Connections screen, if it is not already open (tap / Settings / Connections / Connections).

2. Below My ISP, tap Manage existing connections.

3. Tap and hold the connection you want to use and then select Connect.

4. Unless the phone provider confirmed that you must enter user name, password, and domain settings to access the Internet, tap

OK without entering any

information in this screen. Otherwise, enter the required information and then tap

OK.

5. If the phone prompts for confirmation to connect to the Internet, accept the connection.

The phone dials the configured GPRS access number and then connects to the Internet.

GeoExplorer 6000 Series User Guide 97

Getting Connected 6

A Connectivity notification appears on the handheld as the connection is being made.

After the connection is made you are returned to the My ISP screen.

To confirm that the GeoExplorer series handheld is connected to the phone, or to check the status of the connection at any time, tap the title bar and then tap the Connectivity icon on the pull-down list. The notification shows the name of the current connection, and the time elapsed since the connection was made. To hide the notification, tap

Hide.

Note – If you have an active Wi-Fi connection, the connectivity icon appears as instead.

6. Tap

OK to close the My ISP screen.

7. Tap

OK to close the Connections / Ta sk s screen.

8. Tap to close the Connections screen.

To check the connection status at any time, tap the title bar and then tap the required status icon on the pull-down list.

To end the connection at any time, tap the title bar, tap the required status icon on the pull-down list and then tap

Disconnect.

To connect to a corporate network or Intranet, see page 110.

To send and receive email messages, see Messaging, page 52.

Step 3: Configuring the GNSS field software to use data received from the Internet source

Now that you have connected the GeoExplorer 6000 series handheld to the Internet, you must configure the software to use the connection to receive data.

To use real-time corrections in Trimble field software, see Using real-time corrections

from the Internet below.

To use background map data in the TerraSync software, see Downloading background

map files from an Internet map server, page 99.

Using real-time corrections from the Internet

1. Start the Trimble GNSS field software and then open the Setup section.

2. Tap

Real-time Settings. The Real-time Settings form appears.

3. From the Choice 1 field, select External Source.

4. Configure the external source:

6 Getting Connected

98 GeoExplorer 6000 Series User Guide

a. Tap the Setup button beside the Choice 1

field. The External Source Settings form appears.

b. From the Correction Datum field, select the

same datum as the VRS network coordinate system.

c. From the Type field, select:

– VRS if the real-time correction source is a

VRS network.

– Single Base if the real-time correction

source is a single base station that broadcasts its corrections over the Internet.

d. From the Connection Method field, select Internet.

Typically, the IP address or URL of a VRS network has the format

10.3.123.456:1234, where the digits before the colon (:) are the address, and the digits after the colon (:) are the port number.

e. In the Address field, enter the IP address or URL of the VRS network or the

server that is supplying the corrections from the VRS network.

f. In the Port field, enter the port number that you will use to connect to the

server.

g. If you are connecting to a VRS network through a broadcast server, tap the

Setup button beside the Source field. The GNSS field software attempts to establish a connection to the broadcast server. If the connection is successful, the Select Server form appears. Select the server that you want to use and then tap

Done to return to the External Source Settings form.

h. If you selected a VRS network that requires authentication, the Name and

Password fields appear. Enter the user name and password that you obtained from the service provider.

i. From the Connection Control field, select:

– Auto if you want the GNSS field software to automatically establish and

end connections to the VRS network as necessary.

– Manual if you want to connect or disconnect only when you tap Ext

Source

in the Setup screen.

j. Tap

Done to confirm the settings and return to the Real-time Settings form.

5. Tap

Done to confirm the real-time settings and return to the main screen of the

Setup section.

If you selected Auto in the Connection Control field, the

Ext Source button is

depressed and the software attempts to connect to the server.

GeoExplorer 6000 Series User Guide 99

Getting Connected 6

6. If you selected Manual in the Connection Control field, tap the Ext Source button that appears below the Status bar in the Setup section to connect the Trimble GNSS field software to the Internet correction source.

Tip – To disconnect or reconnect to the server at any time, tap Ext Source. To view the status of the real-time correction source, open the Status section, select the Real-time subsection and then select External from the Summary list button.

Downloading background map files from an Internet map server

1. Make sure that the coordinate system selected in the TerraSync software matches the coordinate system of the map server.

2. In the Map section of the TerraSync software,

pan or zoom to make sure that the

area for which you want a background image is displayed on the map.

If the map server covers the area you are in, it will provide a background image that matches the current map extents.

3. Tap

Layers and then select Background files. The

Background Files form appears.

4. In the Location field select Internet and then use the fields that appear to specify the Map Server type, the URL of the server, the service, and the layers from that service that you want to download.

5. Tap

Done to close the Background File form and

download the selected background map.

This may take some time. When a download is in progress, an icon appears in the top left corner of the map. Once the background file is downloaded, the hourglass icon appears until the downloaded image is rendered and becomes visible.

If you pan or zoom beyond the extents of the downloaded image, new images are downloaded automatically and displayed in the background of the map.

To stop automatic downloading of background files, either clear the address of the map server from the URL field, or set the Location field to Default and then clear the check box next to any files.

Reconnecting to the Internet

To reconnect to the Internet at any time after setting up the connection, repeat the steps listed under Step 2: Connecting to the Internet using the dialup network on

page 96.

If you selected Auto in the Connection Control field of the Trimble GNSS field software, the software automatically connects to the Internet source that is providing real-time differential corrections.

6 Getting Connected

100 GeoExplorer 6000 Series User Guide

To manually reconnect the Trimble GNSS field software to the Internet source that is providing real-time differential corrections, open the software and then tap the

Ext

Source

button that appears below the status bar in the Setup section.

Connecting to the Internet through a Bluetooth-enabled phone using the Bluetooth PAN profile

This section describes how to set up a Bluetooth Personal Area Network (PAN) connection for Internet access, using Bluetooth-enabled cellular phone.

The PAN service is not available on GeoExplorer 6000 series handheld models which have an integrated modem.

Making a Bluetooth PAN connection with a Bluetooth-enabled cellular phone is similar to making a Bluetooth Dialup Networking (DUN) connection (see Connecting

to a Bluetooth-enabled phone for Internet access or real-time corrections (including VRS networks), page 94), in that it enables the handheld to access the Internet. If PAN

connections are supported by your cellular phone, the advantages of using a PAN connection rather than a DUN connection are:

• PAN connections are easier to set up.

• PAN connections automatically attempt to reconnect when the handheld is

resumed from being suspended or shut down.

To access the Internet using a Bluetooth PAN connection to a Bluetooth-enabled cellular phone, you must:

1. Pair the GeoExplorer 6000 series handheld with a cellular phone that supports the Bluetooth PAN profile.

2. Enable the PAN connection on the handheld.

Step 1: Pairing with the cellular phone

1. Make sure that the handheld and the Bluetooth device you want to pair with are within five meters of each other, and that the Bluetooth radio in each device is turned on.

2. On the GeoExplorer 6000 series handheld, tap / Settings / Bluetooth.

3. In the Devices tab, tap Add new device. The handheld searches for other Bluetooth devices and displays them in the list.

If the device you are trying to connect is not displayed in the list, ensure that the device is on and within range and then tap Refresh to search for devices again.

4. Tap the name of the device you want to pair with and then tap

Next on the right

softkey.

5. In the Passcode field, enter a passcode of your choice (between 1 and 16 characters).

Trimble GeoExplorer 6000 series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual