Trimble DCM-300 Quick Start Manual
DCM-300 Modem Quick Start Guide
3:51 pm, Apr 07, 2011
This guide provides step-by-step instructions for a quick setup of the Trimble® DCM-300 modem.
CFX-750 display
j
f
c
p
67259
75741
67095
P3 / GPS connector
g
d
l
h
e
AG25 GNSS antenna 77038-00
k
Main NavController II cable 54601
l
DCM-300 to display cable 82026
m
DCM 300 cellular antenna 72122 +
n
DCM-300 modem 83x00-10
o
1
USB hub
p
DCM-300 power harness
q
2
i
k
n
o
m
q
Item Description P/N Item Description P/N
CFX-750 display 94100-01
c
CFX-750 power cable 77282
d
CFX power cable with relay and
e
switch (power bus)
Basic power cable 67258
f
CFX to NavController II cable with
g
port replicator
2-pin DTM to 2-pin DT power
h
adapter
NavController II 55563-00
i
8 m GPS TNC / TNC RT angle cable 76442
j
51227
82026
FmX integrated display
c
k
n
j
m
p
d
q
f
Item Description P/N Item Description P/N
FmX integrated display 93100-01
c
FmX power cable 66694
d
FmX power cable with relay and
e
switch (power bus)
Basic power cable 67258
f
FmX to NavController II cable with
g
port replicator
2-pin DTM to 2-pin DT power
h
adapter
NavController II 55563-00
i
8 m GPS TNC / TNC RT angle cable 76442
j
67259
75741
67095
AG25 GNSS antenna 68040-00S
k
Main NavController II cable 54601
l
DCM-300 to display cable 82033
m
DCM 300 cellular antenna 72122 +
n
DCM-300 modem 83x00-10
o
1
USB hub
p
DCM power harness
q
P3 / GPS connector
i
g
l
h
e
2
51227
82026
1
The USB hub included in the P/N 82026 harness must be used for the DCM-300 modem to work with the FmX / CFX-750 displays.
2
The P/N 82026 cable has two power harness options; one for connecting to a power bus cable, and another for connecting to machine power. The harness for connecting to machine power has leads for connecting to power, ground, and ignition. The ignition
lead must be connected to a switched +12 V source for the DCM-300 to operate correctly when this harness option is used.
AgGPS 262 receiver
Status messages
c
e
d
f
g
Item Description P/N Item Description P/N
Ag
c
d
e
GPS 262 receiver 55500-xx
DCM-300 modem 83x-00-15
DCM 300 cellular antenna 72122 +
51227
DCM-300 to receiver cable 82133
f
DCM-300 power harness
g
1
82133
Green LED
Power and Telematics
GPS status
Amber LED
Cellular and Wi-Fi status
DCM-300 status Green LED Amber LED
Power On & Booting Solid Off
GPS Signal Blink
Cellular Link N/A Solid
Wi-Fi Link N/A Blink
Wi-Fi and Cellular Link N/A Slow Blink
Poor or no Wireless Signal N/A Fast Blink
Poor or no GPS Signal Fast Blink
System In Sleep Mode Off Off
1
Slow blink is 3 s on/3 s off.
2
Blink is 1 s on/1 s off.
3
Fast blink is 200 ms on/200 ms off
2
3
N/A
2
N/A
1
3
1
The P/N 82026 cable has two power harness options; one for connecting to a power bus cable, and another for connecting
to machine power. The harness for connecting to machine power has leads for connecting to power, ground, and ignition. The
ignition lead must be connected to a switched +12 V source for the DCM-300 to operate correctly when this harness option is
used.
*93020-88-E03*
P/N 93020-88-E03
© 2011. Trimble Navigation Limited. All rights reserved. Trimble, the Globe
and Triangle logo, AgGPS, and FmX are trademarks of Trimble Navigation
Limited, registered in the United States and in other countries. CFX-750 is a
trademark of Trimble Navigation Limited. Version 1.00, Rev A (April 2011).
Loading...