Quick Installation Guide
TV-H100
H/W: V1
Table of Contents
English ......................................................................................................
1. Before You Start
2. Hardware Installation .........................................................................
Troubleshooting ........................................................................................
................................................................................
1
1
2
11
Version 02.17.2009
1. Before you start
Package Contents
TV-H100
?
Quick Installation Guide
?
?Mounting Bracket
?Hexagon screwdriver (1/4” L=6mm)
?Screws, washers and wall mount
screws
Installation Requirements
The following items below are not included. Users must provide the items
themselves. Make sure to have each item on hand before installation.
Internet Camera Server (e.g. TV-IP110, TV-IP110W, TV-IP212,
?
TV-IP212W, TV-IP312, TV-IP312W)
?Dry Wall or Wood surface
?Power Cord
?Wire Stripper
?Phillips Screwdriver
? Pliers
?Electrical Tape
?RJ-45 cable (For Wired Internet Camera Server)
?RJ-45 connector (For Wired Internet Camera Server)
?TEW-ASAK (For Wireless Internet Camera Server)
?TEW-L406 or TEW-L412 (For Wireless Internet Camera Server)
?Outdoor Antenna (e.g. TEW-AO14D) (For Wireless Internet Camera
Server)
*Note: You must know how to terminate a network cable with an RJ-45
connector in order to install a wired internet camera server into the TV-H100.
If you do not know how to terminate a network cable with an RJ-45 connector,
please consult a network professional.
1
English
2. Hardware Installation
Note: Configure your Internet Camera Server to match your network before
installing the device.
1. Remove the screws from the
back of the camera enclosure.
Save these screws. You will
need to use these screws later.
2. Slide out the back end of the
enclosure.
3. Unscrew the metal bracket from
the TV-H100. Save this screw and
washer. You will need to use this
screw and washer later.
English
2
4. Use the following screw to mount
the Internet Camera Server to the
metal bracket.
5. Screw the metal bracket back in
to the TV-H100.
6. Connect the IR shelter to the
Internet Camera Server
(TV-IP312 and TV-IP312W only).
7. Take the Internet Camera Server's
power adapter and cut about 4
inches from the end the power
connector using the wire cutter.
Note: This is the AC/DC adapter
that is included with your Internet
Camera Server.
3
English
8. Take a knife or box cutter and cut
along the middle to split the cable
into two strands.
9. Use a wire stripper to remove the
insulation to expose the copper
wiring.
10. Run the power adapter and RJ-45
Ethernet cable from the base to
the top of the mounting arm.
Make sure to leave one end of
the RJ-45 Ethernet cable
unterminated.
11. Remove one of the caps from the
enclosure.
12. Insert the unterminated end of the
cable through the cap.
4
English
13. Terminate the Ethernet cable.
14. Insert the Ethernet cable through
the cable access hole. Then
screw in the cap securely.
15. Remove one of the caps from the
enclosure.
16. Insert the power adapter through
the cap.
17. Insert the power adapter through
the cable access hole. Then
screw in the cap securely.
English
5
18. Connect the two ends of the
power adapter back by twisting
the copper wiring. Make sure you
do not cross the copper wires.
19. Use electrical tape to seal the
cables back together. Make sure
to seal the individual strands
separately.
20. Connect the Ethernet cable to the
Internet Camera Server.
21. Connect the power adapter to the
Internet Camera Server.
22. Slide the back end of the
enclosure back in.
6
English
Installing External Antenna to Wireless Internet
Camera
1. Remove the antenna from the back
of your wireless Internet Camera
Server.
2. Run the pigtail cable that comes
with the TEW-ASAK from the base
to the top of the mounting arm.
3. Remove one of the caps from the
enclosure.
4. Insert the pigtail cable that comes
with the TEW-ASAK through the
cap.
English
7
5. Insert the pigtail cable that comes
with the TEW-ASAK through the
cable access hole. Then screw in
the cap securely.
6. Connect the pigtail cable that
comes with the TEW-ASAK and
the power adapter to the Internet
Camera Server.
7. Slide the back end of the enclosure
back in.
8. Follow the directions in the QIG for
the TEW-ASAK to connect the
surge arrestor to your outdoor
antenna (e.g. TEW-AO14D).
8
English
Mounting the Camera Housing
1. Place the mounting bracket against
the wall and mark each of the four
holes with a pencil.
2. Drill holes for the screws at each
marked position. Make sure the
drill bit matches the size of the
provided white screws.
3. Insert the screws into the holes.
4. Use the bracket screws to mount
the mounting bracket to the
TV-H100. Use the provided Hex
screwdriver to secure the mounting
bracket.
9
English
5. Adjust the mounting bracket to the
desired position. Then use the
provided Hex screwdriver and turn
it clockwise to secure position.
6. Align the Wall Mount bracket with
the screws, and then use the
provided nuts and washers to
secure it.
Your installation is now complete.
For detailed information regarding the TV-H100 configuration and advanced
settings, please refer to the User's Guide included on the Utility & Driver CDROM or TRENDnet's website at www.trendnet.com
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
10
English
Troubleshooting
Q1:
After I put my Internet Camera Server in the enclosure, the image is distorted.
What should I do?
A1:
First, make sure that you have adjusted the focus on your camera. Second,
mount the TV-H100 so that it's not in direct view of the sun. Third, if you are using
a day/night camera with auto iris lens, make sure to push the camera all the way
to the front so that the IR shelter is touching the glass.
My Ethernet cable will not fit through the cap. What should I do?
Q2:
A2:
You must first run the Ethernet cable unterminated. Once the Ethernet cable
is run through the cap and the cable access hole, then terminate the Ethernet
cable with an RJ-45 jack.
My antenna cable will not fit through the cap. What should I do?
Q3:
You must use the TEW-ASAK with the TEW-L406/L412. See Installing
A3:
External Antenna to Wireless Internet Camera in section 2 for more instructions.
If you still encounter problems or have any questions regarding the TV-H100, please
contact TRENDnet's Technical Support Department.
11
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA
Copyright ©2009. All Rights Reserved. TRENDnet.
Loading...