Traxxas 56076-1 User Manual

MODEL 56076-1

owner’s manual

introduction

3 BEFORE YOU

PROCEED

4 SAFETY

PRECAUTIONS

6 TOOLS, SUPPLIES,

AND REQUIRED

EQUIPMENT

7 ANATOMY OF

THE SUMMIT

8 QUICK START:

GETTING UP

TO SPEED

9 TRAXXAS TQ

RADIO SYSTEM

16 ADJUSTING THE

ELECTRONIC SPEED

CONTROL

18 DRIVING YOUR MODEL

21 TUNING

ADJUSTMENTS

27 MAINTAINING

YOUR MODEL

i

Thank you for purchasing the new Traxxas Summit electric monster
truck. The Summit is the most advanced electric monster truck
ever created, with multi-terrain capabilities that far exceed those of
any other monster truck. Designed from the start to optimize the
advantages of electric power, Summit builds on the success and
innovation of the E-Revo racing monster truck with the first-ever
remote-locking differentials and transmitter-operated high-low
transmission for total mastery of any terrain without compromising
speed or handling.

This manual contains the instructions you will need to operate and
maintain your model so that you can enjoy it for years to come.
We want you to feel confident that you own one of the best­performing models in the market and that it is backed by a team
of professionals who aim to provide the highest level of factory
support possible. Traxxas models are about experiencing total
performance and satisfaction, not just with your model, but also
with the company that stands behind it.

We know you’re excited about getting your new model on
the road, but it’s very important that you take some time to
read through the Owner’s Manual. This manual contains all the
necessary setup and operating procedures that allow you to unlock
the performance and potential that Traxxas engineers designed
into your model. Even if you are an experienced R/C enthusiast,

it’s important to read and follow the procedures in this manual.

Thank you again for going with Traxxas. We work hard every day
to assure you the highest level of customer satisfaction possible.
We truly want you to enjoy your new model!

Traxxas Support

Traxxas support is with you every step of the
way. Refer to the next page to find out how to
contact us and what your support options are.

Quick Start

This manual is designed with a Quick
Start path that outlines the necessary
procedures to get your model up
and running in the shortest time possible. If you are an
experienced R/C enthusiast, you will find it helpful and fast.
Be sure and read through the rest of the manual to learn
about important safety, maintenance, and adjustment
procedures. Turn to page 8 to begin.

REGISTERING YOUR MODEL

In order to serve you better as our customer, please
register your product within 10 days of your purchase
online at Traxxas.com/register.

Traxxas.com/register

28 TQ

i

TUNING GUIDE

2 • SUMMIT

ADVANCED

FCC Compliance

This device contains a module that complies with the limits for a Class B digital device as described in part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The limits for a Class B digital device are designed to provide reasonable protection against harmful interference in residential settings. This product generates, uses and can radiate radio
frequency energy, and, if not operated in accordance with the instructions, may cause harmful interference to radio communications. The user is cautioned that changes or modifications
not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canada, Industry Canada (IC)

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the
following two conditions: This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency (RF) Exposure Statement

This equipment complies with radio frequency exposure limits set forth by FCC and Industry Canada for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the radiator and your body or bystanders and must not be co-located or operating in conjunction with any other
antenna or transmitter.

before you proceed

Carefully read and follow all instructions in this and any
accompanying materials to prevent serious damage to your
model. Failure to follow these instructions will be considered
abuse and/or neglect.

Before running your model, look over this entire manual and
examine the model carefully. If for some reason you decide it is not
what you wanted, then do not continue any further. Your hobby

dealer absolutely cannot accept a model for return or exchange
after it has been run.

Warnings, Helpful Hints, & Cross-References

Throughout this manual, you’ll notice warnings and helpful hints
identified by the icons below. Be sure to read them!

An important warning about personal safety or avoiding
damage to your model and related components.

Special advice from Traxxas to make things easier
and more fun.

Refers you to a page with a related topic.

SUPPORT

If you have any questions about your model or its operation,
call the Traxxas Technical Support Line toll-free at:
1-888-TRAXXAS (1-888-872-9927)*

Technical support is available Monday through Friday from 8:30am
to 9:00pm central time. Technical assistance is also available at
Traxxas.com. You may also e-mail customer support with your
question at [e-mail]. Join thousands of registered
members in our online community at Traxxas.com.

Traxxas offers a full-service, on-site repair facility to handle any
of your Traxxas service needs. Maintenance and replacement
parts may be purchased directly from Traxxas by phone or online
at BuyTraxxas.com. You can save time, along with shipping
and handling costs, by purchasing replacement parts from your
local dealer.

Do not hesitate to contact us with any of your product support needs.
We want you to be thoroughly satisfied with your new model!

Traxxas
6200 Traxxas Way
McKinney, Texas 75070
Phone: [phone]
Toll-free 1-888-TRAXXAS

Internet
Traxxas.com
E-mail: [e-mail]

Entire contents ©2014 Traxxas.
Traxxas, Ready-To-Race, TQ, Titan,
Summit, and EVX-2 are trademarks
or registered trademarks of
Traxxas. Other brand names and
marks are the property of their
respective holders and are used
only for purposes of identification.
No part of this manual may be
reproduced or distributed in print
or electronic media without the
express written permission of
Traxxas. Specifications are subject
to change without notice.

*Toll-free support is available to U.S. residents only.

SUMMIT • 3

bluehighway font

Choose the Model That is Right For You. For individual Models

No previous experience with radio controlled models is required.
Models require a minimum of setup, maintenance, or support equipment.

Previous experience with radio controlled models is recommended.
Models require a higher level of setup, maintenance, or support equipment.

No previous experience with radio controlled models is required.
Model requires a minimum of setup, maintenance, or support equipment.

Previous experience with radio controlled models is recommended.
Model requires a higher level of setup, maintenance, or support equipment.

BELOW TEXT HAS BEEN UPDATED on 3-14-07
Kent wants maintenance text to be at the END of the paragraph.-- KB

SAFETY PRECAUTIONS

All instructions and
precautions outlined in this
manual should be strictly
followed to ensure safe
operation of your model.

This model is not intended
for use by children under
14 years of age without the
supervision of a responsible
and knowledgeable adult.

Previous experience with
radio controlled models
is recommended. Models
require a higher level of
setup, maintenance, or
support equipment.

1

4 • SUMMIT

All of us at Traxxas want you to safely enjoy your new model.
Operate your model sensibly and with care, and it will be exciting,
safe, and fun for you and those around you. Failure to operate your
model in a safe and responsible manner may result in property
damage and serious injury. The precautions outlined in this manual
should be strictly followed to help ensure safe operation. You alone
must see that the instructions are followed and the precautions are
adhered to.

Important Points to Remember

• Your model is not intended for use on public roads or congested
areas where its operation can conflict with or disrupt pedestrian or
vehicular traffic.

• Never, under any circumstances, operate the model in crowds of
people. Your model is very fast and could cause injury if allowed to
collide with anyone.

• Because your model is controlled by radio, it is subject to radio
interference from many sources that are beyond your control. Since
radio interference can cause momentary losses of radio control,
always allow a safety margin in all directions around the model in
order to prevent collisions.

• The motor, battery, and speed control can become hot during use.
Be careful to avoid getting burned.

• Don’t operate your model at night, or anytime your line of sight to
the model may be obstructed or impaired in any way.

• Most importantly, use good common sense at all times.

Batteries and Battery Charging

Your model uses rechargeable batteries that must be handled with
care for safety and long battery life. Make sure to read and follow
all instructions and precautions for charging and maintaining the
batteries. It is your responsibility to charge and care for the battery
packs properly. In addition to your battery and charger instructions,
here are some more tips to keep in mind.

• Do not charge batteries inside of an automobile. Do not charge
batteries while driving in an automobile. The charger is equipped
with a long cord intended to allow the battery to be charged
outside of an automobile when using the automobile’s auxiliary
power socket. If the cord will not reach outside of the automobile,
find another power source.

• Never charge batteries on wood, cloth, carpet or on any other
flammable material.

• Do not operate the charger in a cluttered space, or place objects on
top of the charger or battery.

• If a battery gets hot to the touch during the charging process
(temperature greater than 140°F / 60°C), disconnect the battery
from the charger and discontinue charging immediately.

• Always store battery packs safely out of the reach of children and
pets.

• Do not short-circuit the battery pack. This may cause burns and
severe damage to the battery pack and create the risk of fire.

• Do not expose the charger to water or moisture.

• Do not disassemble the charger.

• Use the supplied charger to charge the included battery. See
“Charging the Battery Pack” on page 11.

• Never leave batteries to charge unattended.

• Remove the battery from the model while charging.

• Always unplug the battery from the electronic speed control when
the model is not in use and when it is being stored or transported.

• Allow the battery pack to cool off between runs (before charging).

• Children should have responsible adult supervision when charging
and handling batteries.

• Do not use battery packs that have been damaged in any way.

• Do not use battery packs that have damaged wiring, exposed
wiring, or a damaged connector.

• Do not short-circuit the battery pack. This may cause burns and
severe damage to the battery pack.

• Do not burn or puncture the batteries. Toxic materials could be
released. If eye or skin contact occurs, flush with water.

• Store the battery pack in a dry location, away from heat sources
and direct sunlight.

• Nickel Metal Hydride batteries must be recycled or disposed of
properly.

1500

3600

SAFETY PRECAUTIONS

Recycling Your Traxxas Power Cell NiMH Battery

Traxxas strongly encourages you to recycle your Power Cell NiMH
battery when it has reached the end of its useful life. Do not throw

your battery in the trash. All Power Cell NiMH battery packs display

the RBRC (Rechargeable Battery Recycling Corporation) icon,
indicating they are recyclable. To find a recycling center near you,
ask your local hobby dealer or visit www.call2recycle.org.

Speed Control

Your model’s electronic speed control (ESC) is an extremely
powerful electronic device capable of delivering high current. Please
closely follow these precautions to prevent damage to the speed
control or other components.

• Always adhere to the minimum and maximum limitations of the
speed control as stated in the
specifications on page 16.
If your ESC operates on two
batteries, do not mix battery
types and capacities. Use the
same voltage and capacity
for both batteries. Using
mismatched battery packs
could damage the batteries

1500

3600

Do not mix battery
capacities. Use two

batteries with the

same capacity.

Do not use a 6-cell 7.2V
battery in combination

with a 7-cell battery

8.4V pack.

and electronic speed control.

• Disconnect the Battery: Always disconnect the battery or batteries
from the speed control when not in use.

• Insulate the Wires: Always insulate exposed wiring with heat shrink
tubing to prevent short circuits.

• Transmitter on First: Switch on your transmitter first before
switching on the speed control to prevent runaways and erratic
performance.

• Do not remove the heat sinks from the ESC. Three heat sinks
are factory-installed on the speed control and must be used for
maximum cooling and performance.

• Don’t Get Burned: The ESC and motor can become extremely hot
during use, so be careful not to touch them until they cool. Supply
adequate airflow for cooling.

• Use the Factory-Installed Stock Connectors: Do not change the
battery and motor connectors. Improper wiring can cause fire or
damage to the ESC. Please note that modified speed controls can
be subject to a rewiring fee when returned for service.

• No Reverse Voltage: The ESC is not protected against reverse
polarity voltage.

• No Schottky Diodes: External Schottky diodes are not compatible
with reversing speed controls. Using a Schottky diode with your
Traxxas speed control will damage the ESC and void the 30-day
warranty.

LiPo Batteries

Lithium Polymer (LiPo) batteries are becoming popular for use
in R/C models due to their compact size, high energy density,
and high-current output. However, these types of batteries
require special care and handling procedures for long life and safe
operation. Warning: LiPo batteries are intended only for advanced

users that are educated on the risks associated with LiPo battery
use. Traxxas does not recommend that anyone under the age of
14 use or handle LiPo battery packs without the supervision of a
knowledgeable and responsible adult.

Your model is able to use LiPo batteries with nominal voltage not
to exceed 11.1 volts (3S packs). LiPo batteries have a minimum safe
discharge voltage threshold that should not be exceeded. The EVX-2
electronic speed control is equipped with built-in Low-Voltage
Detection that alerts the driver when LiPo batteries have reached
their minimum voltage (discharge) threshold. It is the driver’s

responsibility to stop immediately to prevent the battery pack
from being discharged below its safe minimum threshold.

Low-Voltage Detection on the speed control is just one part of a
comprehensive plan for safe LiPo battery use. It is critical for you,

the user, to follow all other instructions supplied by the battery
manufacturer and the charger manufacturer for proper charging,
use, and storage of LiPo batteries. Do not attempt to charge LiPo
batteries with the Traxxas charger included in this package. Make
sure you understand how to use your LiPo batteries. Be aware

that Traxxas shall not be liable for any special, indirect, incidental,
or consequential damages arising out of the installation and/or use
of LiPo batteries in Traxxas models. If you have questions about

LiPo battery usage, please consult with your local hobby dealer
or contact the battery manufacturer. As a reminder, all batteries

should be recycled at the end of their useful life.

DO NOT ATTEMPT TO CHARGE LIPO BATTERIES OR ANY OTHER TYPE
OF BATTERY WITH THE INCLUDED TRAXXAS CHARGER.

SUMMIT • 5

For more information on
batteries, see Use the Right
Batteries on page 11.

Recommended Equipment

These items are not required
for the operation of your
model, but are a good idea to
include in any R/C toolbox:

• Safety glasses

• Traxxas Ultra Premium Tire
Glue, Part #6468 (CA glue)

• Hobby knife

• Side cutters and/or needle
nose pliers

• Phillips screwdriver

• Soldering iron

tools, supplies, and required equipment

Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate
and maintain your model.

Supplied Tools and Equipment

4-way wrenchShock wrench 5mm turnbuckle wrench Suspension multi-tool Antenna nut wrench Universal wrench

17mm wheel wrench 2.0mm “T” wrench 2.5mm “T” wrench

Battery Retainers3.0mm “L” wrench

Body clips

6 • SUMMIT

Two NiMH battery packs* NiMH battery charger*

Required Equipment

4 AA alkaline batteries

*Battery and charger style are subject to change and may vary from images.

anatomy of the summit

Battery Door Release Tab

Traxxas High-Current
Connector

Rear Body Mount

Rear Bumper

Rocker

Push Rod

Rear Suspension
Arm

Motor

Electronic Speed Control

Steering Servo

Front T-Lock Servo

Slipper Clutch

Transmission

Chassis

Pivot Ball

Axle Carrier

Push Rod

Rocker

Front Body

Mount

Shock

Front Bumper

Rear Half Shaft

Toe Link

Battery Compartment
Vent

Antenna Mount

LED Light Pipe

Receiver Box

Battery Compartment Door

Transmission Shifting Servo

Rear T-Lock Servo

Skid Plate

Front Suspension

Arm

Spring Preload

Adjuster

SUMMIT • 7

The Quick Start Guide is
not intended to replace the
full operating instructions
available in this manual.
Please read this entire
manual for complete
instructions on the proper
use and maintenance of
your model.

quick start: getting up to speed

The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom
corners of Quick Start pages.

1. Read the safety precautions on page 4 8. Detail your model • See page 9

For your own safety, understand where carelessness and misuse
could lead to personal injury.

2. Install batteries in the transmitter • See page 11 9. Drive your model • See page 18

The transmitter requires 4 AA alkaline batteries (sold separately). Driving tips and adjustments for your model.

3. Charge the battery packs • See page 11 10. Maintaining your model • See page 27

Fully charge the two provided battery packs. Charge your batteries
now so it will be ready when you finish the other setup procedures.

4. Install battery packs in the model • See page 11

Your model requires two fully charged battery packs (included).

5. Turn on the radio system • See page 13

Make a habit of turning the transmitter on first and off last.

Apply other decals if desired.

Follow these critical steps to maintain the performance
of your model and keep it in excellent running condition.

Look for the Quick Start
logo at the bottom of
Quick Start pages.

8 • SUMMIT

6. Check servo operation • See page 14

Make sure the steering servos are working correctly.

7. Range test the radio system • See page 14

Follow this procedure to make sure your radio system works properly
at a distance and that there is no interference from outside sources.

TRAXXAS TQi RADIO SYSTEM

INTRODUCTION

Your model includes the latest Traxxas TQi 2.4GHz transmitter with Traxxas

™

Link

Model Memory. The transmitter’s easy-to-use design provides instant
driving fun for new R/C enthusiasts, and also offers a full complement of
pro-level tuning features for advanced users – or anyone interested in
experimenting with the performance of their model. The steering and throttle
channels feature adjustable Exponential, End Points, and Sub-Trims. Steering
and braking Dual-Rate are also available. Many of the next-level features are
controlled by the Multi-Function knob, which can be programmed to control
a variety of functions. The detailed instructions (page 28) and Menu Tree
(page 30) included in this manual will help you understand and operate the
advanced functions of the new TQi radio system. For additional information
and how-to videos, visit Traxxas.com.

RADIO AND POWER SYSTEM TERMINOLOGY

Please take a moment to familiarize yourself with these radio and power
system terms. They will be used throughout this manual. A detailed
explanation of the advanced terminology and features of your new radio
system begins on page 28.

BEC (Battery Eliminator Circuit) - The BEC can either be in the receiver or in

the ESC. This circuit allows the receiver and servos to be powered by the
main battery pack in an electric model. This eliminates the need to carry a
separate pack of 4 AA batteries to power the radio equipment.

Current - Current is a measure of power flow through the electronics, usually

measured in amps. If you think of a wire as a garden hose, current is a
measure of how much water is flowing through the hose.

ESC (Electronic Speed Control) - An electronic speed control is the electronic

motor control inside the model. The EVX-2 uses MOSFET power transistors to
provide precise, digital proportional throttle control. Electronic speed controls
use power more efficiently than mechanical speed controls so that the batteries
run longer. An electronic speed control also has circuitry that prevents loss of
steering and throttle control as the batteries lose their charge.

Frequency band - The radio frequency used by the transmitter to send signals

to your model. This model operates on the 2.4GHz direct-sequence spread
spectrum.

LiPo - Abbreviation for Lithium Polymer. Rechargeable LiPo battery packs are

known for their special chemistry, which allows extremely high energy density
and current handling in a compact size. These are high performance batteries
that require special care and handling. LiPo battery packs are for advanced
users only.

mAh – Abbreviation for milliamp hour, a measure of the capacity of the

battery pack. The higher the number, the longer the battery will last
between recharges.

Neutral position - The standing position that the servos seek when the

transmitter controls are at the neutral setting.

NiCad - Abbreviation for nickel-cadmium. The original rechargeable hobby

pack, NiCad batteries have very high current handling, high capacity, and
can last up to 1000 charging cycles. Good charging procedures are required
to reduce the possibility of developing a “memory” effect and shortened run
times.

NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH batteries

offer high current handling and much greater resistance to the “memory”
effect. NiMH batteries generally allow higher capacity than NiCad batteries.
They can last up to 500 charge cycles. A peak charger designed for NiMH
batteries is required for optimal performance.

Receiver - The radio unit inside your model that receives signals from the

transmitter and relays them to the servos.

Resistance - In an electrical sense, resistance is a measure of how an object

resists or obstructs the flow of current through it. When flow is constricted,
energy is converted to heat and is lost.

Servo - Small motor unit in your model that operates the steering mechanism.

Transmitter - The hand-held radio unit that sends throttle and steering

instructions to your model.

Trim - The fine-tuning adjustment of the neutral position of the servos,

made by adjusting the throttle and steering trim knobs on the face of the
transmitter. Note: The Multi-Function knob must be programmed to serve as a

throttle trim adjustment.

Thermal Shutdown Protection - Temperature sensing electronics are used

in the ESC to detect overloading and overheating of the transistor circuitry.
If excessive temperature is detected, the unit automatically shuts down to
prevent damage to the electronics.

2-channel radio system - The TQ radio system, consisting of the receiver, the

transmitter, and the servos. The system uses two channels: one to operate
the throttle and one to operate the steering.

2.4GHz Spread Spectrum – This model is equipped with the latest R/C
technology. Unlike AM and FM systems that require frequency crystals and
are prone to frequency conflicts, the TQi system automatically selects and
locks onto an open frequency and offers superior resistance to interference
and “glitching.”

Voltage - Voltage is a measure of the electrical potential difference between

two points, such as between the positive battery terminal and ground.
Using the analogy of the garden hose, while current is the quantity of water
flow in the hose, voltage corresponds to the pressure that is forcing the
water through the hose.

550 and 540 - These numbers refer to the size of the motor. 550 motors have

armatures that are 30% longer than 540 motors.

Applying the Decals

The main decals for your
model have been applied at
the factory. Additional decals
are printed on self-adhesive
clear mylar and are die-cut
for easy removal. Use a
hobby knife to lift the corner
of a decal and lift it from the
backing.

To apply the decals, place
one end down, hold the
other end up, and gradually
smooth the decal down with
your finger as you go. This
will prevent air bubbles.
Placing both ends of the
decal down and then trying
to smooth it out will result
in air pockets. Look at the
photos on the box for typical
decal placement.

8

SUMMIT • 9

TRAXXAS TQi RADIO SYSTEM

EVX-2 Wiring Diagram

Your model is equipped with the newest TQi 2.4GHz

transmitter with Traxxas Link™ Model Memory. The
transmitter has two channels for controlling your throttle
and steering. The receiver inside the model has 5 output
channels. Your model is equipped with one servo and an
electronic speed control.

TRANSMITTER AND RECEIVER

Set Button

Red/Green Status LED

see page 29 for more info

Menu Button

Steering
Trim

Multi-Function
Knob

Shift Switch
(Channel 3)

Throttle
Trigger

Throttle Neutral Adjust

T-Lock Switch (Channel 4)

Steering

Sensor Expansion

Link
Button

Wheel

MODEL WIRING DIAGRAM

Channel 4 Front
T-Lock Servo

Channel 1
Steering Servos

Antenna

V/T
V/T

RPM
RPM

BA
B
A

TT

CH5

T

CH5

T
/
/

CH4

CH4
CH3
CH3

CH2

CH2
CH1
CH1

CH1
CH1

S
S

+

+

-

-

** Accessory sensor port for use with TQi Docking Base (see Traxxas.com and included materials for more information)

to

LED Lights

V/T - Voltage/Temp Senor Port**
RPM - RPM Sensor Port**
BATT/

CH5 - Battery/Channel 5
CH4 - Channel 4
CH3 - Channel 3
CH2 - Speed Control
CH1 - Steering Servo
CH1 - Channel 1

EVX-2 ELECTRONIC SPEED CONTROL

**

Port

High-Current

Battery Connector

To Motor

Channel 3
Shift Servo

WATERPROOF

16.8V ESC

Channel 5
Rear T-Lock
Servo

Motor
(Titan® 775)

Channel 2
EVX-2 Electronic
Speed Control

10 • SUMMIT

LED

Power Switch Battery Compartment

** Accessory sensor port for use with the Telemetry Expander Module (see Traxxas.com for more information)

Heat Sinks

LED

WATERPROOF

16.8V E SC

EZ-Set Button

TRAXXAS TQi RADIO SYSTEM

INSTALLING TRANSMITTER BATTERIES

Your TQi transmitter uses 4 AA batteries. The battery
compartment is located in the base of the transmitter.

1. Remove the battery compartment door by pressing the tab
and sliding the door open.

2. Install the batteries in the correct orientation as indicated in
the battery compartment.

3. Reinstall the battery door and snap it closed.

4. Turn on the transmitter and check the status indicator for a
solid green light.

If the status LED flashes red, the transmitter
batteries may be weak, discharged or
possibly installed incorrectly. Replace
with new batteries. The power indicator
light does not indicate the charge level
of the battery pack installed in the model. Refer to the
Troubleshooting section on page 29 for more information on
the transmitter Status LED codes.

CHARGING THE BATTERY PACK

The Traxxas Battery Charger is a fully featured NiMH (Nickle Metal
Hydride) charger. It features 4-amp charge current for fast charging
and advanced peak detection to optimize every charge. Take this
compact charger with you wherever you want to have radio controlled
fun! Do not charge batteries inside of an automobile. Read the Safety

Precautions section of this manual.

1. Plug the charger into a 12-volt
automotive auxiliary power
socket. The charger is compatible

with 12-volt automotive auxiliary
power sockets only. The LED on the
charger will glow red to indicate it
is ready to charge a battery.

2. Connect the battery to begin
charging. Plug the battery into

the charger. The charger’s LED
will flash green, indicating that
charging has begun. The flashing
green LED on the charger indicates
the charge progress.

3. Disconnect the battery when
charging is complete. The

Traxxas 4-amp DC charger uses
sophisticated voltage-detection
circuitry to monitor the battery and
automatically stop charging when
the pack has reached
maximum capacity. When

CHARGE PROGRESS

the battery is fully charged,
the LED will light solid
green. The battery will
be warm in your hand.
Disconnect the battery.

CHARGER LED INDICATION MEANING

Solid Red LED Ready for Charging

Slowly Flashing Green LED Charging (see Charge Progress chart)

Solid Green LED Battery Fully Charged

Flashing Red LED Charger error

1

2

3

1 green flash 0 - 25% charged

x1

2 green flashes 25% - 50% charged

x2

3 green flashes 50% - 75% charged

x3

4 green flashes 75% or more charged

x4

Solid green LED 100% charged

Disconnected

Connected

Charged

The included charger is
designed for use only with
Traxxas NiMH batteries
with iD. Legacy Traxxas
High-Current Connectors
are not compatible with this
charger. DO NOT try to force
legacy connectors into the
charge connector.

If the status LED doesn’t light
green, check the polarity
of the batteries. Check
rechargeable batteries for
a full charge. If you see any
other flashing signal from the
LED, refer to the chart on page
29 to identify the code.

Use the Right Batteries

Your transmitter uses
AA batteries. Use new
alkaline batteries. Do
not use rechargeable AA
cells to power the TQi
transmitter, as they will not
provide sufficient voltage
for optimum transmitter
performance.

Caution: Discontinue running
your model at the first sign of
weak batteries (flashing red
light) to avoid losing control.

2, 3,4

SUMMIT • 11

TRAXXAS TQi RADIO SYSTEM

Battery iD

Your model’s included battery
pack is equipped with Traxxas
Battery iD. This exclusive
feature allows Traxxas battery
chargers (sold separately)
to automatically recognize
connected battery packs
and optimize the charge
settings for the battery.
This eliminates the need to
worry over charger settings
and menus for the easiest
and safest charging solution
possible. Visit Traxxas.com to
learn more about this feature
and available Traxxas iD
chargers and batteries.

The Traxxas
High-Current Connector

Your model is equipped
with the Traxxas High-
Current Connector. Standard
connectors restrict current
flow and are not capable of
delivering the power needed
to maximize the output
of the EVX-2. The Traxxas
connector’s gold-plated
terminals, with large contact
surfaces, ensure positive
current flow with the least
amount of resistance. Secure,
long-lasting, and easy to
grip, the Traxxas connector
is engineered to extract all
the power your battery has
to give.

INSTALLING BATTERY PACKS

The Summit requires two fully charged battery packs. These batteries
are included with the model.

Battery Installation

1. Open the battery compartment door by pressing on the release tabs.

2. Install the provided
battery pack with the
battery wires facing the
rear of the model.

3. Make sure the battery is
snug in the compartment.
If not, remove the battery
and make adjustment to
the battery retainer tab.

4. Route the battery wire
through the slot near
the vent.

5. Close the battery door, making sure not to pinch the battery wires.
Be sure both release tabs are fully engaged with the door. Do not
connect the battery packs to the EVX-2 at this time. Note: Always

unplug the batteries and remove from the model after use.

Using Different Battery Configurations

The battery compartments in the Summit are adjustable to
accommodate a large variety of battery packs. Depending on model,
the battery compartments are configured at the factory to accept either
7-cell NiMH stick packs or 2-Cell LiPo battery packs. The Summit battery
compartments have three key features for keeping your batteries secure:

1. A foam rubber cushion

2. A spring clip (This is removable for use with taller batteries.)

A battery retainer tab (This is adjustable to fit a variety of battery sizes.)

3.

We recommend using this combination for all batteries. Make sure to
adjust the battery retainer tab to keep your battery pack snug against
the foam rubber cushion. This does not need to be very tight. It only
needs to prevent the battery from moving excessively during use.

Foam

Cushion

Spring

Clip

Battery Wire Slot

7-cell Battery Orientation

Retainer

Tab

6-cell battery packs:

Swap the battery retainer
tabs from the left and right
battery compartments.
This will provide additional
adjustment needed to keep

6-cell Battery Orientation

the 6-cell battery packs snug against the foam rubber cushions.

Adjusting Battery Position

The best handling and

Retainer Tabs

performance is achieved
when the batteries are
positioned to the front of
the battery compartment
(against the foam rubber
cushion); however, you can

Alternate Rear Position

6-cell Battery Orientation

reposition the batteries to
change the weight distribution and handling if desired. The Summit
includes an extra set of battery retainer tabs that can be used in the
front of the battery compartment to move the batteries toward the rear
of the truck.

When using the battery retainer tabs in the front of the battery
compartment, use two 3x10 countersunk cap screws to retain each
battery retainer tab. Do not use the battery retainer tabs in the front of

the battery compartments when using LiPo batteries that are not in a
hard plastic case.

The battery compartments can be reconfigured to accept many sizes of
LiPo batteries. If you are using batteries that are very thick, the spring
clip may need to be removed from the battery compartment.

Spring Clip Removal

1. Pull down on the inside of
the clip.

2. Push the clip in toward
the center of the model to
release.

12 • SUMMIT

TRAXXAS TQi RADIO SYSTEM

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

Spring Clip Installation

1. Insert the two tabs on
the spring clip into the
rectangular tab slots in
the chassis.

2. Rotate the spring clip
upward.

3. Snap the tabs into place.

Many LiPo batteries do not use a hard plastic case. If using LiPo
batteries that do not have a hard case, always be sure to use the foam
rubber cushion in the front of the battery compartment. Do not use

the battery retainer tabs in the front of the battery compartments
when using LiPo batteries that are not in a hard plastic case. A hard

front impact or crash when driving can damage the LiPo batteries.

RADIO SYSTEM RULES

•

Always turn your TQi transmitter on first and off last. This procedure
will help to prevent your model from receiving stray signals from
another transmitter, or other source, and running out of control. Your
model has electronic fail-safes to prevent this type of malfunction, but
the first, best defense against a runaway model is to always turn the
transmitter on first and off last.

1

Always turn your

transmitter on first.

• In order for the transmitter and receiver to bind to one another,

the receiver in the model must be turned on within 20 seconds
of turning on the transmitter. The transmitter LED will flash fast
red, indicating a failure to link. If you miss it, simply turn off the
transmitter and start over.

• Always turn on the transmitter before plugging in the battery.

• Always use new batteries for the radio system. Weak batteries will

limit the radio signal between the receiver and the transmitter. Loss

of the radio signal can cause you to lose control of your model.

Plug in the battery.

2

3

Turn on the model.

RADIO SYSTEM CONTROLS

Unlock
Diffs

Lock
Front
Diffs

Lock
Both
Diffs

High Gear

T

U

R

N

R

I

G

H

T

T

U

R

N

L

E

F

T

Neutral

Brake/Reverse

Low Gear

Forward

RADIO SYSTEM BASIC ADJUSTMENTS

Throttle Neutral Adjustment

The throttle neutral adjustment is located on the
transmitter face and controls the forward/reverse
travel of the throttle trigger. Change the adjustment
by pressing the button and sliding it to the desired
position. There are two settings available:

50/50: Allows equal travel for both acceleration and reverse.

70/30: Allows more throttle travel (70%) and less reverse travel (30%).

Note: We strongly recommend to leave this control in its factory
location until you become familiar with all the adjustments and
capabilities of your model. To change the throttle neutral adjust position,
turn the transmitter off before adjusting the neutral position. You will
need to reprogram your electronic speed control to recognize the
70/30 setting. Turn to EVX-2 Setup Programming on page 16 for instructions.

Steering Trim

The electronic steering trim located on the
face of the transmitter adjusts the neutral
(center) point of the steering channel.

Remember, always turn the
TQi transmitter on first and
off last to avoid damage to
your model.

Stop immediately at the first
sign of weak batteries. Never
turn the transmitter off when
the battery pack is plugged
in. The model could run out
of control.

5

SUMMIT • 13

TRAXXAS TQi RADIO SYSTEM

Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.

Automatic Fail-Safe

The TQi transmitter and
receiver are equipped with
an automatic fail-safe system
that does not require user
programming. In the event of
signal loss or interference, the
throttle will return to neutral
and the steering will hold its
last commanded position. If
the fail-safe activates while
you are operating your model,
determine the reason for
signal loss and resolve the
problem before operating
your model again.

In order to re-acquire the
signal after the fail-safe has
activated, you will need
to walk a longer distance
closer to the model than the
distance the model travelled
out of range. Simply keep
walking towards the model
until you re-acquire the signal.

14 • SUMMIT

6,7

Multi-Function Knob

The Multi-Function knob can be programmed
to control a variety of functions. From the
factory, the Multi-Function knob controls
steering sensitivity, also known as exponential
or “expo.” When the knob is turned counterclockwise all the way to the
left (default position), expo is off and steering sensitivity will be linear
(the most commonly used setting). Turning the knob clockwise will
“add expo” and decrease the steering sensitivity in the initial range of
steering wheel travel left or right from center. For more detail on steering
exponential, refer to page 15.

USING THE RADIO SYSTEM

The TQi Radio System has been pre-adjusted at the factory. The
adjustment should be checked before running the model in case of
movement during shipping. Here’s how:

1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).

2. Elevate the model on a block or a stand so that all the tires are
off the ground. Make sure your hands are clear of the moving
parts of the model.

3. Plug the battery packs in the model into the speed control.

4. The on/off switch is integrated into the speed control. Press and
release the EZ-Set button on the speed control to turn the model
on. The LED will shine RED or GREEN (see note below). To turn the
EVX-2 off, press the EZ-Set button until the LED turns off. Note:

If the model is factory equipped with LiPo batteries, the LED will be
green, indicating that Low-Voltage Detection is activated. If the
model is factory equipped with NiMH batteries, the LED will be red,
indicating that Low-Voltage Detection is disabled. Never use LiPo
batteries while Low-Voltage Detection is disabled. See page 16 for
more on EVX-2 setup and operation.

5. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak batteries.

6. When looking down at the model, the front wheels should be
pointing straight ahead. If the
wheels are turned slightly to the left
or right, slowly adjust the steering
trim control on the transmitter until
they are pointing straight ahead.

7. Gently operate the throttle trigger to ensure that you have
forward and reverse operation, and that the motor stops when
the throttle trigger is at neutral. WARNING: Do not apply full

throttle in forward or reverse while the model is elevated.

8. Once adjustments are made, turn off the receiver on your model,
followed by the hand-held transmitter.

Range-Testing the Radio System

Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.

1.

Turn on the radio system and check its operation as described in

the previous section.

2.

Have a friend hold the model. Make sure hands and clothing are

clear of the wheels and other moving parts on the model.

3.

Walk away from the model with the transmitter until you reach

the farthest distance you plan to operate the model.

4.

Operate the controls on the transmitter once again to be sure that

the model responds correctly.

5.

Do not attempt to operate the model if there is any problem with

the radio system or any external interference with your radio
signal at your location.

Higher Speeds Require Greater Distance

The faster you drive your model, the more quickly it will near the limit
of radio range. Use caution to keep your model in range. If you want
to see your model achieve its maximum speed, it is best to position
yourself in the middle of the truck’s running area, not the far end,
so you drive the truck towards and past your position. In addition to
maximizing the radio’s range, this technique will keep your model
closer to you, making it easier to see and control.

Your model’s radio system is designed to operate reliably up to the
approximate distance that it is no longer easy or comfortable to see
and control the model. Most drivers will struggle to see and drive
their model at distances farther than a football field (300+ feet). At
greater distances, you could lose sight of your model and you may
also exceed the radio system’s operating range, which will cause
the failsafe system to activate. For best visibility and control of your
model, keep your model within 200 feet, regardless of the maximum
range available.

No matter how fast or far you drive your model, always leave adequate
space between you, the model, and others. Never drive directly toward
yourself or others.

TRAXXAS TQi RADIO SYSTEM

TQi Binding Instructions

For proper operation, the transmitter and receiver must be
electronically “bound.” This has been done for you at the factory.
Should you ever need to re-bind the system or bind to another
transmitter or receiver, follow these instructions. Note: The receiver

must be connected to a 4.8-6.0v (nominal) power source for binding, and
the transmitter and receiver must be within 5 feet of each other.

1. Press and hold the transmitter’s SET button as you switch the
transmitter on. The transmitter’s LED will flash red slowly. Release
the SET button.

2. Press and hold the receiver’s LINK button as you switch on
the speed control (by pressing the EZ-Set button). Release the
LINK button.

3. When the transmitter and receiver’s LEDs turn solid green, the
system is bound and ready for use. Confirm that the steering and
throttle operate properly before driving your model.

Steering Sensitivity (Exponential)

The Multi-Function knob on the TQi transmitter has been programmed
to control Steering Sensitivity (also known as exponential). The
standard setting for Steering Sensitivity is “normal (zero exponential),”
with the dial full left in its range of travel. This setting provides linear
servo response: the steering servo’s movement will correspond exactly
with the input from the transmitter’s steering wheel. Turning the
knob clockwise from the left will result in “negative exponential” and
decrease steering sensitivity by making the servo less responsive near
neutral, with increasing sensitivity as the servo nears the limits of its
travel range. The farther you turn the knob, the more pronounced the
change in steering servo movement will be. The term “exponential”
comes from this effect; the servo’s travel changes exponentially
relative to the input from the steering wheel. The exponential effect
is indicated as a percentage—the greater the percentage, the greater
the effect. The illustrations below show how this works.

Normal Steering Sensitivity (0% exponential)

In this illustration, the
steering servo’s travel
(and with it, the steering
motion of the model’s
front wheels) corresponds
precisely with the steering
wheel. The ranges are
exaggerated for illustrative purposes.

Decreased Steering Sensitivity (Negative Exponential)

By turning the Multi-
Function knob clockwise,

Turning Range

at Transmitter

Effective Turning

on Model

Range

the steering sensitivity
of the model will be
decreased. Note that a
relatively large amount
of steering wheel travel
results in a smaller amount
of servo travel. The farther
you turn the knob, the more pronounced the
effect becomes. Decreased steering sensitivity
may be helpful when driving on low-traction surfaces, when
driving at high speed, or on tracks that favor sweeping turns where
gentle steering inputs are required. The ranges are exaggerated for
illustrative purposes.

Experiment! Try varying degrees of exponential. It’s easy to go back
to “zero” if you don’t like the effect. There’s no wrong way to adjust
exponential. Any setting that makes you more comfortable with your
model’s handling is the “right setting.”

SETTING UP THE ANTENNA

The receiver antenna has been set up and
installed from the factory.

When reinstalling the antenna, first slide
the antenna wire into the bottom of the
antenna tube until the white tip of the
antenna is at the top of the tube under the
black cap. Insert the base of the tube into
the antenna post. Take care not to crimp
the antenna wire. Slide the crimp nut
over the antenna tube and screw it onto
the antenna post. Use the supplied tool
to tighten the crimp nut on the post just
until the antenna tube is securely in place.
Do not over tighten or crush the antenna
wire against the chassis. Do not bend or

kink the antenna wire! See the sidebar
for more information. Do not shorten the
antenna tube. The minimum height is
62mm.

Antenna

Tip

Antenna

Tube

Antenna

Wrench

Antenna

Crimp Nut

Antenna

Post

To prevent loss of radio range
do not kink or cut the black wire,
do not bend or cut the metal tip,
and do not bend or cut the white
wire at the end of the metal tip.

Correct

NoNo No

SUMMIT • 15

ADJUSTING THE ELECTRONIC SPEED CONTROL

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

16.8V ESC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

EVX-2 Wiring Diagram

EVX-2 Specifications

Input Voltage:*

NiMH - 12-14 cells
(14.4 - 16.8 volts)

LiPo - 4 cells (14.8 volts)

Motor limit: 12-turns (550)

Continuous current: 30A

Peak current : 180A

BEC voltage: 6.0V DC

Transistor type: MOSFET

Motor/Battery Wiring: 14-gauge

Protection: Thermal shutdown

* This model requires two battery packs. Input

voltage listed by cells refers to the total
number of cells that may be installed in
the model. You may install two 6-cell NiMH
packs, two 7-cell NiMH packs, or two 2-cell
LiPo packs. Do not mix NiMH and LiPo battery
packs. Damage to the model and batteries
will result.

16 • SUMMIT

The EVX-2 electronic speed control is factory set and should not require any
adjustments. These instructions are provided for your reference.

Battery Settings (Low-Voltage Detection Setting)

The Low-Voltage Detection circuitry constantly monitors the battery voltage.
When the battery voltage begins to reach the minimum recommended discharge
voltage threshold for LiPo battery packs, the EVX-2 will limit the power output
to 50% throttle. When the battery voltage attempts to fall below the minimum
threshold, the EVX-2 will shut down all motor output. The LED on the speed
control will slowly blink red, indicating a low voltage shutdown. The EVX-2 will stay
in this mode until a fully charged battery is connected.

Your model comes equipped with two Traxxas battery packs. The EVX-2 speed
control’s Low-Voltage Detection has been disabled for best performance with
these batteries. The speed control’s LED will glow red when it is turned on,
indicating Low-Voltage Detection is disabled. Be certain to activate Low-Voltage
Detection if you install LiPo batteries in your model. Never use LiPo batteries

while Low-Voltage Detection is disabled.

Verify that Low-Voltage Detection is DISABLED:

1. Turn on the transmitter (with the throttle at neutral).

2. Connect fully charged battery packs to the EVX-2.

3. Press and release the EZ-Set button to turn the EVX-2 on. If the LED is solid red,
then the Low-Voltage Detection is DISABLED (not safe to use LiPo batteries).
If the LED is solid green, then Low-Voltage Detection is ACTIVATED.

To activate Low-Voltage Detection (LiPo setting):

1. Make sure the LED on the EVX-2 is on and shines red.

2. Press and hold the EZ-Set button (the

A

B

LED will turn off) (A). After ten seconds,
the motor will beep twice and the LED
will shine green. Release the button (B).

3. Low-Voltage Detection is now ACTIVATED.

Red LED: Hold 10 seconds 2 Beeps: LED shines green

To disable Low-Voltage Detection (NiMH setting):

1. Make sure the LED on the EVX-2 is on and shines green.

2.

Press and hold the

EZ-Set

button (the LED

A

B

will turn off) (A). After ten seconds, the
motor will beep three times and the LED
will shine red. Release the button (B).

3. Low-Voltage Detection is now DISABLED.

Transmitter Adjustments for the EVX-2 ESC

Before attempting to program your EVX-2, it is important to make sure your TQi

Green LED: Hold 10 seconds 3 Beeps: LED shines red

transmitter is properly adjusted (set back to the factory defaults). Otherwise, you
may not get the best performance from your speed control.

The transmitter should be adjusted as follows:

1. Turn the transmitter off.

2. Hold both MENU and SET.

3. Turn the transmitter on.

4. Release MENU and SET. The transmitter LED will blink red.

5. Press MENU once. The transmitter LED will blink red twice repeatedly.

6. Press SET to clear settings. The LED will turn solid green and the transmitter is
restored to default.

Setup Programming (Calibrating your ESC and transmitter)
Read through all of the following programming steps before you begin. If you
get lost during programming or receive unexpected results, simply unplug the
batteries, wait a few seconds, plug the battery packs in, and start over.

1. Disconnect each of the motor wires between the EVX-2 and the

A

motors. This is a precaution to prevent runaway when the speed
control is turned on before it is programmed.

2. Connect two fully charged battery packs to the EVX-2.

3. Turn on the transmitter (with the throttle

at neutral).

B

Green then Red

4. Press and hold the EZ-Set button (A).

The LED will first turn green and then red.
Release the EZ-Set button.

5. When the LED blinks RED ONCE, pull the throttle

trigger to the full throttle position

Once Red

C

and hold it there (B).

6. When the LED blinks RED TWICE, push the

throttle trigger to the full reverse and hold it
there (C).

7. When the LED blinks GREEN ONCE, programming is complete.

Twice Red

D

The LED will then shine green or red (depending on Low-
Voltage Detection setting), indicating the EVX-2 is on and at
neutral (D).

Solid

EVX-2 Operation

To operate the speed control and test the programming, place the vehicle on a
stable block or stand so all of the drive wheels are off the ground. Reconnect the
motor wires. Always make sure that objects and fingers are clear of the wheels.

Note that in the steps below, Low-Voltage Detection is DISABLED (factory default with NiMH
batteries) and the LED shines red. If Low-Voltage Detection is ACTIVATED (factory default
with LiPo batteries), the LED will shine green instead of red in the steps below. Never use LiPo

batteries while Low-Voltage Detection is disabled.

1. With the transmitter on, press the EZ-Set button for ½ second, until the LED

shines red, then immediately release the button. This turns on the EVX-2. If you
press and release too quickly, you may hear the steering servos jump but the
LED may not stay on. (Note: If the throttle is not at neutral or if the throttle trim has

been altered, the LED will turn off after one second and the wheels may begin to
drive.)

2. Apply forward throttle. The LED will turn off until full throttle power is reached.

At full throttle, the LED will shine red.

3. Move the trigger forward to apply the brakes. Note that braking control is fully

proportional. The LED will turn off until full braking power is reached. At full
brakes, the LED will shine red.

ADJUSTING THE ELECTRONIC SPEED CONTROL

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

16.8V E SC

WATERPROOF

4. Return the throttle trigger to neutral. The LED will shine red.

5. Move the throttle trigger forward again to engage reverse (Profile #1). The LED
will turn off. Once full reverse power is reached, the LED will shine red.

6. To stop, return the throttle trigger to neutral. Note that there is no
programmed delay when changing from reverse to forward. Use caution to
avoid slamming the speed control from reverse to forward. On high-traction
surfaces, this could result in transmission or driveline damage.

7. To turn the EVX-2 off, press the EZ-Set button until the red LED turns off.

Thermal Shutdown Protection

The EVX-2 is equipped with thermal shutdown protection to guard against
overheating caused by excessive current flow. If the operating temperature exceeds
safe limits, the EVX-2 will automatically shut down and the EVX-2 LED will flash red.
The LED on the face of the EVX-2 will continuously flash red, even if the throttle
trigger is moved back and forth. After the speed control cools down to a safe level,
the LED will continuously shine red. The EVX-2 will once again function normally.

EVX-2 Profile Selection

The speed control is factory set to Profile #1. To change the profile, follow the
steps provided below. The speed control should be connected to the receiver
and battery, and the transmitter should be adjusted as described previously. The
profiles are selected by entering the programming mode.

EVX-2 Profile Description

Profile #1 (Sport Mode): 100% Forward, 100% Brakes, 100% Reverse
Profile #2 (Race Mode): 100% Forward, 100% Brakes, No Reverse
Profile #3 (Training Mode): 50% Forward, 100% Brakes, 50% Reverse

Selecting Sport Mode (Profile #1)

1. Connect two fully charged battery packs to

A

B

the EVX-2 and turn on your transmitter.

2. With the EVX-2 off, press and hold the EZ-Set

button until the light turns solid green,
then solid red, and then begins blinking red
(indicating the Profile numbers).

Green to Red to Off

C

One blink Red

D

3. When the light blinks red once, release the

EZ-Set button.

4. The LED will blink and then turn solid green

(Low-Voltage Detection ACTIVE) or red (Low-

Release

Solid

Voltage Detection DISABLED). The model is ready to drive.

Selecting Race Mode (Profile #2)

1. Connect two fully charged battery packs to

A

B

the EVX-2 and turn on your transmitter.

2. With the EVX-2 off, press and hold the EZ-Set

button until the light turns solid green,

Green to Red to Off

Two blinks Red

then solid red, and then begins blinking red
(indicating the Profile numbers).

3. When the light blinks red twice, release the

C

D

EZ-Set button.

4. The LED will blink and then turn solid green
(Low-Voltage Detection ACTIVE) or red (Low-
Voltage Detection DISABLED). The model is
ready to drive.

Release

A

Solid

B

Selecting Training Mode* (Profile #3)

1. Connect two fully charged battery packs to the
EVX-2 and turn on your transmitter.

2. With the EVX-2 off, press and hold the EZ-Set
button until the light turns solid green,

Green to Red to Off

C

Three blinks Red

D

then solid red, and then begins blinking red
(indicating the Profile numbers).

3. When the light blinks red three times, release
the EZ-Set button.

Release

Solid

4. The LED will blink and then turn solid green (Low-Voltage Detection ACTIVE)
or red (Low-Voltage Detection DISABLED). The model is ready to drive.

Note: If you missed the mode you wanted, keep the EZ-Set button pressed down and
the blink cycle will repeat until a Mode is selected.

LED Codes and Protection Modes

• Solid Green: EVX-2 power-on light. Low-Voltage Detection is ACTIVATED

(LiPo setting).

• Solid Red: EVX-2 power-on light. Low-Voltage Detection is DISABLED

(NiCad/NiMH setting). Never use LiPo batteries while Low-Voltage Detection

is disabled.

• Fast Blinking Red: The EVX-2 is equipped with thermal shutdown protection

to guard against overheating caused by excessive current flow. If the operating
temperature exceeds safe limits, the EVX-2 will automatically shut down. Let
the EVX-2 cool. Make sure your model is properly geared for the conditions (see
page 25).

• Slow Blinking Red (with Low-Voltage Detection on): The EVX-2 has entered

Low-Voltage Protection. When the battery voltage begins to reach the
minimum recommended discharge voltage threshold for LiPo battery packs,
the EVX-2 will limit the power output to 50% throttle. When the battery voltage
attempts to fall below the minimum threshold, the EVX-2 will shut down all
motor output. The LED on the speed control will slowly blink red, indicating a
low-voltage shutdown. The EVX-2 will stay in this mode until a fully charged
battery is connected.

• Fast Blinking Green: The EVX-2’s LED will blink fast green if Throttle Neutral

Protection is activated or if the speed control is not receiving a signal. Make
certain the speed control is properly plugged into the receiver and the
transmitter is switched on. If this does not restore normal operation, then the
EVX-2 is indicating the transmitter’s Throttle Trim (see page 28) is incorrectly
set. Reset the throttle trim to the “0” position.

Patented Training Mode (Profile
#3) reduces forward and reverse
throttle by 50%. Training Mode
is provided to reduce the power
output, allowing beginning
drivers to better control the
model. As driving skills improve,
simply change to Sport or Race
Mode for full-power operation.

Tip For Fast Mode Changes

The EVX-2 is set to Profile 1 (Sport
Mode) as the default. To quickly
change to Profile 3 (Training
Mode), with the transmitter on,
press and hold the SET button until
the light blinks red three times and
then release. For full power, quickly
change back to Profile 1 (Sport
Mode) by pressing and holding the
SET button until the light blinks red
one time and then releasing.

Throttle Neutral Protection
Your model’s EVX-2 speed control
also features Throttle Neutral
Protection. If the transmitter’s
throttle trim setting is changed
while the speed control is
switched off, Throttle Neutral
Protection prevents the speed
control from activating the motor
until the throttle trim is corrected.
Throttle Neutral Protection
also prevents the model from
suddenly accelerating if the
speed control is switched on
while the transmitter’s trigger
is being held. When the trigger
is returned to neutral, the EVX-2
will operate properly.

*Patented

SUMMIT • 17

DRIVING YOUR MODEL

18 • SUMMIT

Now it’s time to have some fun! This section contains instructions on
driving and making adjustments to your model. Before you go on, here
are some important precautions to keep in mind.

•

Allow the model to cool for a few minutes between runs. This is
particularly important when using high-capacity battery packs that
allow extended periods of running. Monitoring temperatures will
extend the lives of the batteries and motor.

•

Do not continue to operate the model with low batteries or you
could lose control of it. Indications of low battery power include
slow operation and sluggish servos (slow to return to center). Stop
immediately at the first sign of weak batteries. When the batteries in
the transmitter become weak, the red power light will begin to flash.
Stop immediately and install new batteries.

•

Do not drive the model at night, on public streets, or in large crowds
of people.

•

If the model becomes stuck against an object, do not continue to run
the motor. Remove the obstruction before continuing. Do not push or
pull objects with the model.

•

Because the model is controlled by radio, it is subject to radio interference
from many sources beyond your control. Since radio interference can
cause momentary losses of control, allow a safety margin of space in all
directions around the model in order to prevent collisions.

•

Use good, common sense whenever you are driving your model.
Intentionally driving in an abusive and rough manner will only result
in poor performance and broken parts. Take care of your model so
that you can enjoy it for a long time to come.

•

High-performance vehicles produce small vibrations that may loosen
hardware over time. Frequently check wheel nuts and other screws on
your vehicle to ensure that all hardware remains properly tightened.

Operating the High-Low Transmission

Summit’s High-Low transmission is operated via the red
rocker switch above the transmitter grip; depressing
the upper part of the switch engages Low, depressing
the lower part of the switch engages High. Summit
may be shifted from Low to High while the truck is
moving. However, it is recommended to slow to a
speed appropriate for Low gear (about 5mph) before

9

shifting from High to Low. This will reduce strain on the
transmission gears. Although Summit’s 775 motor has
ample torque for climbing and crawling in second gear,

using first gear in situations that require low speed will extend motor life.
Limit second-gear use to high-speed running.

Operating the T-Lock Differentials

For most driving, the Summit will perform best with
both differentials unlocked or “open” (T-Lock switch
back). This will give Summit maximum steering
performance and the tightest possible turning radius,
and will also reduce strain on the drive components.
If open differentials cause you to lose traction over
loose terrain or when traversing an obstacle, you can
use the T-lock switch to lock the front differential or
both differentials. To lock the front differential only, bring the truck
and all four wheels to a complete stop, then move the T-Lock switch to
the middle position. Apply throttle slowly until the T-Lock engages (it
will take just a moment), then use the throttle as needed. To lock both
differentials, come to a complete stop and move the T-Lock switch to
the forward-most position. As with a full-size 4WD vehicle, Summit’s
high-speed handling and steering precision are reduced when one or
both differentials are locked. Locked differentials should only be used for
difficult obstacles that require minimum speed and maximum traction.
High-speed driving with locked differentials is not recommended.

About Run Time

A large factor affecting run time is the type and condition of your
batteries. The milliamp hour (mAh) rating of the batteries determines
how large their “fuel tank” is. A 3000 mAh battery pack will theoretically
run twice as long as a 1500 mAh sport pack. Because of the wide variation
in the types of batteries that are available and the methods with which
they can be charged, it’s impossible to give exact run times for the model.
Another major factor that affects run time is how the model is driven.
Run times may decrease when the model is driven repetitively from a
stop to top speed and with repetitive hard acceleration.

Tips for Increasing Run Time

•

Use batteries with the highest mAh rating you can purchase.

•

Use a high-quality peak-detecting charger.

•

Read and follow all maintenance and care instructions provided by
the manufacturer of your batteries and charger.

• Keep the EVX-2 cool.

•

Lower your gear ratio. Installing a smaller pinion gear will lower your
gear ratio and cause less power draw from the motor and batteries,
and reduce overall operating temperatures.

Get plenty of airflow across the ESC heat sinks.

DRIVING YOUR MODEL

•

Maintain your model. Do not allow dirt or damaged parts to cause
binding in the drivetrain. Keep the motor clean.

mAh Ratings and Power Output

The mAh rating of the battery can affect your top-speed performance.
The higher capacity battery packs experience less voltage drop under
heavy load than low mAh rated packs. The higher voltage potential
allows increased speed until the battery begins to become discharged.

RUNNING IN WET CONDITIONS

Your new Traxxas Summit is designed with water-resistant features
to protect the electronics in the model (receiver, servos, electronic
speed control). This gives you the freedom to have fun driving your
Summit through puddles, wet grass, snow, and through other wet
conditions. Though highly water resistant, the Summit should not be
treated as though it is submersible or totally 100% waterproof. Water
resistance applies only to the installed electronic components. Running
in wet conditions requires additional care and maintenance for the
mechanical and electrical components to prevent corrosion of metal
parts and maintain their proper function.

Precautions

•

Without proper care, some parts of your model can be seriously
damaged due to contact with water. Know that additional
maintenance procedures will be required after running in wet
conditions in order to maintain the performance of your model.
Do not run your model in wet conditions if you are not willing to
accept the additional care and maintenance responsibilities.

•

Not all batteries can be used in wet environments. Consult your
battery manufacturer to see if their batteries can be used in wet
conditions. Do not use LiPo batteries in wet conditions.

•

The transmitter is not water resistant. Do not subject it to wet
conditions, such as rain.

•

Do not operate your model during a rain storm or other inclement
weather where lightning may be present.

•

Do not allow your model to come in contact with saltwater (ocean
water), brackish water (between fresh water and ocean water), or
other contaminated water. Saltwater is highly conductive and highly
corrosive. Use caution if you plan to run your model on or near a beach.

•

Even casual water contact can reduce the life of your motor. Special
care must be taken to modify your driving style in wet conditions to
extend the life of the motor (details below).

Before Running Your Vehicle in Wet Conditions

1.

Consult the section “After Running Your Vehicle in Wet Conditions”
before proceeding. Make sure you understand the additional
maintenance required with wet running.

2.

The wheels have small holes molded in to allow air to enter and exit
the tire during normal running. Water will enter these holes and get
trapped inside the tires if holes are not cut in the tires. Cut two small
holes (4mm or 3/16” diameter) in each tire. Each hole should be near
the tire centerline, 180 degrees apart.

3.

Confirm that the receiver box O-ring and cover are installed correctly
and secure. Make sure the screws are tight and the blue o-ring is not
visibly protruding from the edge of the cover.

4.

Confirm that your batteries can be used in wet conditions.

5.

Use Low gear when running in mud, deep puddles, snow, or similar
situations that will restrict the tires and put much higher loads on the
motor. Although the Summit’s 775 motor has ample torque in second
gear, using first gear in situations that require low speed will extend
motor life. Limit second-gear use to high-speed running on dry ground.

Motor Precautions

•

Titan motor life can be greatly reduced in mud and water. If the
motor gets excessively wet or submerged, use very light throttle
(run the motor slowly) until the excess water can run out. Applying
full throttle to a motor full of water can cause rapid motor failure.
Your driving habits will determine motor life with wet motor. Do not
submerge the motor under water.

•

Do not gear the motor by temperature when running in wet
conditions. The motor will be cooled by water contact and will not
give an accurate indication of appropriate gearing.

After Running Your Vehicle in Wet Conditions

1. Drain the tires by spinning the tires at full throttle to “sling” the water
out. An easy way to do this is to remove the body and set the truck
upside down on a flat surface. Apply full throttle so the tires spin and
throw the excess water out of the holes you cut into the tires.

2. Remove the batteries.

3. Rinse excess dirt and mud off the truck with low-pressure water, such
as from a garden hose. Do not use a pressure washer or other high­pressure water. Avoid directing water into the bearings, transmission,
differentials, etc.

SUMMIT • 19

DRIVING YOUR MODEL

4. Blow off the truck with compressed air (optional, but recommended).
Wear safety glasses when using compressed air.

5. Remove the wheels from the truck.

6. Spray all the bearings, drivetrain, and fasteners with WD-40® or
similar water-displacing light oil.

7. Let the truck stand or you may blow off with compressed air. Placing
the truck in a warm, sunny spot will aid drying. Trapped water and oil
will continue to drip from the truck for a few hours. Place it on a towel
or piece of cardboard to protect the surface underneath.

8. As a precautionary step, remove the sealed receiver box cover. While
unlikely, humidity or tiny amounts of moisture or condensation may
enter the receiver box during wet running. This can cause long-term
problems with the sensitive electronics in the receiver. Removing
the receiver box cover during storage allows the air inside to dry. This
step can improve the long-term reliability of the receiver. It is not
necessary to remove the receiver or unplug any of the wires.

9. Additional Maintenance: Increase your frequency of disassembly,
inspection, and lubrication of the following items. This is necessary
after extended wet use or if the vehicle will not be used for an
extended period of time (such as a week or longer). This additional
maintenance is needed to prevent any trapped moisture from
corroding internal steel components.

• Stub axle housing bearings: Remove, clean, and re-oil the bearings.

• Front and rear differential: Remove,
disassemble, clean, and re-grease
the differentials. Refer to your
exploded view diagrams for help with
disassembly and reassembly.

• Transmission: Remove, disassemble,
clean, and re-grease the transmission
components. Use a light coating of
wheel bearing grease (from an auto
parts store) on the metal gear teeth.
No grease is required for the nylon gears. Refer to your exploded
view diagrams for help with disassembly and reassembly.

• Titan motor: Remove the motor, clean with aerosol motor cleaner,
and re-oil the bushings with lightweight motor oil. Be sure to wear
eye protection when using spray aerosol cleaners.

RECEIVER BOX: MAINTAINING A WATERTIGHT SEAL

Removing and Installing Radio Gear

The unique design of the receiver box allows the removal and
installation of the receiver without losing the ability to maintain a
watertight seal in the box. The patent-pending wire clamp feature
gives you the ability to also install aftermarket radio systems and
maintain the watertight features of the receiver box.

Removing the Receiver

1. To remove the cover, remove the two 3x10mm button-head cap screws.

2. To remove the receiver from the box, simply lift it out and set to the side.
The antenna wire is still inside the clamp area and cannot be removed yet.

3. Remove the wire clamp by removing the two 2.8x8mm cap screws.

4. Unplug the servo cables from the receiver and remove the receiver.

Receiver Installation

1. Always install the wires into the box before installing the receiver.

2. Install the antenna wire and the

servo cables into the receiver box.

3. Arrange the wires neatly using the

wire guides in the receiver box. The
excess wire will be bundled inside
the receiver box. Label which wire is
for which channel.

4. Apply a small bead of silicone grease

(Traxxas part #1647) to the wire clamp.

Install the wire clamp and tighten the two

5.

2.5x8mm cap screws securely.

6. Install the receiver into the box and plug

the wires into receiver. Refer to page 10
for the wiring diagram.

7. Make sure the clear plastic light pipe in

the receiver box is aligned above the
LED on the receiver.

8. Make sure the o-ring is properly seated

into the groove in the receiver box so
that the cover will not pinch it or damage it in any way.

9. Install the cover and tighten the two 3x10mm button-head cap

screws securely.

10. Inspect the cover to make sure that the o-ring seal is not visible.

20 • SUMMIT

TUNING ADJUSTMENTS

Summit does not require any specialized knowledge or understanding
of its unique suspension and drivetrain to perform typical, everyday
setup and tuning adjustments. Adjustment procedures for alignment,
spring rate, damping, steering, and ride height are covered here.

SUSPENSION TUNING

Springs

Summit’s springs have
been carefully selected
to provide the best
combination of roll
stiffness and bump­absorbing ability. If you
wish to install softer or
stiffer springs, Traxxas
offers optional tuning
springs. Higher rate
springs are stiffer, and
can be used to reduce
sag, body lean, and brake
dive for a more responsive handling feel. Lower rate springs are softer,
and will increase traction and suspension articulation when traversing
difficult terrain. Refer to your parts list for a complete part number
listing. Springs are identified by dots of color on their ends.

Optional springs available from
Traxxas are listed to the right.
Refer to your parts list for a
complete part number listing.
Higher rate springs are stiffer.
Springs can be identified by
dots of color on one end.

Ride Height Adjustment

Summit’s ride height can be finely tuned by adjusting suspension sag
via the preload adjusters on the shock bodies. Thread the preload
adjuster down the shock body to raise Summit’s ride height, or thread
the adjuster up the shock body to lower ride height. If threading the
preload adjusters to the maximum ride height position still allows more
suspension sag than you prefer, stiffer springs should be installed.

120mm Travel

Dot Color Spring Rate

Double Yellow 28.0 lb/in (4.9 N/mm)

(Standard Rear)

Double Orange 30.8 lb/in (5.4 N/mm)

(Standard Front)

Blue 33.7 lb/in (5.9 N/mm)
Purple 36.5 lb/in (6.4 N/mm)

Adjusting the Pivot Ball Caps

The pivot ball caps should be adjusted so
that the pivot balls operate freely in the
axle carriers with no excess play. Use the
provided four-way suspension multi-tool to
tighten or loosen the pivot ball cap.

Rockers
(Progressive Rate/ Suspension Travel)

One of the most exciting aspects of Summit’s suspension is the inboard
shock (damper) arrangement that uses pivoting rockers to translate
vertical wheel travel into linear shock motion. The rockers can be
changed to increase or decrease the maximum wheel travel and also to
change the progressive rate of the suspension.

The progressive rate determines how much the force at the wheel
produced by the springs being compressed (wheel force) will vary with
suspension travel (or vertical travel of the wheel). On a progressive
suspension arrangement, the wheel force will increase at a faster and
faster rate as the suspension is compressed. It feels as though the shock
spring gets progressively stiffer the more you compress the suspension.
On a linear suspension arrangement, the wheel force increases linearly as
the suspension is compressed. The spring does not feel any stiffer, even
when the suspension is fully compressed. This provides a very “plush”
feeling suspension with seemingly bottomless suspension travel.

Rocker Arm Total Travel Progressive Rate

Progressive 1

Progressive 2

Progressive 3

Long Travel

(stock)

90mm

(60mm up / 30mm down)

90mm

(60mm up / 30mm down)

90mm

(60mm up / 30mm down)

120mm

(80mm up / 40mm down)

Low

Medium

High

Low

A total of three different rocker arm sets are available for Summit. All
will allow the wheel to travel a total of 90mm in the vertical direction.
From the ride height position, the wheel will be able to travel 60mm
in the upward direction (bump) and 30mm in the downward direction
(droop). Summit is equipped with the long-travel rocker arms for
120mm of total travel. The progressive rate can be increased or

Important: The shocks are
assembled at the factory
with a center-to-center
distance (between the rod
end balls) of 87mm. Any time
the shocks are removed and
disassembled, this distance
should be checked to ensure
proper operation of the
suspension.

87mm

SUMMIT • 21

TUNING ADJUSTMENTS

A camber gauge (available
at your local hobby shop)
can be a useful tool for
alignment setting.

All of the toe links are installed
on the truck so that the left­hand thread indicators point
to the same direction. This
makes it easier to remember
which way to turn the wrench
to increase or decrease toe
link length (the direction is the
same at all four corners). Note
that the groove in the hex
indicates the side of the toe
link with the left-hand threads.

22 • SUMMIT

decreased by installing different rocker arm sets. The rockers are labeled
Progressive 1 to Progressive 3. Progressive 1 rockers will provide a low
progressive rate that maintains consistent damping force across the
whole range of suspension travel. Progressive 2 rockers provide a larger
degree of rate change, and Progressive 3 rockers have the greatest rate
difference. Progressive 3 rockers will improve high-speed cornering on
smooth surfaces by providing a firmer feel. Remember that Progressive
1, 2, and 3 rockers all provide 90mm of travel, 30mm less than the
Summit’s stock 120mm long-travel rockers. This may improve road
handling, but will reduce suspension articulation in rough terrain. Body
roll, brake dive, and rear squat will also be reduced. Always change all
four rockers as a complete set. Do not mix rates and travel.

When using the Progressive 1, 2, or 3 rockers, Traxxas #5439 springs
(3.8 rate gold) provide a good starting point for suspension tuning.

The chart

below demonstrates the effect of the various rocker arms on
wheel force as the suspension is compressed. On the progressive rate,
wheel force is light at first and increases as the suspension is compressed.

20
18
16
14
12
10

8
6

Wheel Force

4
2

0

10 20 30 40 50 60 70 80 90

Wheel Travel

Progressive Rate Travel

Constant Rate Travel

SHOCK TUNING

Shock Oil

The 4 oil-filled aluminum shocks (dampers) effectively control the
suspension movement by preventing the wheels and tires from
continuing to “bounce” after rebounding from a bump. Changing the oil
in the shocks can vary the suspension damping effect. Changing the oil to
a higher viscosity oil will increase damping. Lowering the viscosity of the
oil will cause the suspension damping to be reduced. Damping should
be increased (with higher viscosity oil) if the model is bottoming easily
over jumps. Damping should be decreased (with thinner viscosity oil) if
the model is hopping over small bumps and feels unstable. The viscosity
of shock oil is affected by extremes in operating temperature; an oil of
certain viscosity will become less viscous at higher temperatures and more

viscous at lower temperatures. Operating

Multi-tool Shock Functions

in regions with cold temperatures may
require lower viscosity oil. From the
factory, the shocks are filled with SAE­50W silicone oil. Only use 100% silicone
oil in the shock.

Replacing Shock Oil

The shocks have to be removed
from the vehicle and disassembled

A. Tighten/Loosen Upper Cap

to change the oil.

1. Remove the

lower spring retainer

and shock spring.

2. Remove the

upper shock cap
using the shock wrench and the
suspension multi-tool.

3.

Empty the used shock oil

B. Tighten/Loosen Lower Cap

from the shock body.

4.

Fill the shock with new silicone shock

oil up to the top of the shock body.

5. Slowly move the piston up and down
(always keeping it submerged in oil)
to release the air bubbles. Let the
shock sit for a few minutes to allow

C. Remove/Install Rod End

any remaining air bubbles to surface.

6. Slowly thread the upper cap with the installed shock bladder onto
the shock body with the suspension multi-tool. The excess oil will
bleed out of the small hole in the shock cap.

7. Tighten the shock cap until snug. Use the included steel shock
wrench to hold onto the shock body while tightening.

Shock Pistons

shock pistons can be replaced with the available optional pistons to

The
vary the amount of damping. Optional pistons with bypass holes that
are larger or smaller (1, 2, or 3) than the factory-installed stock pistons
can be used to decrease or increase damping respectively. Change the
pistons if you only have one weight of shock oil available to you. From
the factory, Summit is equipped with #2 pistons in the front and #2
pistons in the rear.

TUNING ADJUSTMENTS

Shock disassembly

The shocks must be removed from the vehicle and disassembled to
change the pistons. Use the shock exploded views included with the
model to aid in the assembly process.

1. Remove the spring and lower spring retainer from the shock.

2. Remove the shock cap (A) and empty the shock body of shock oil.

3. Remove the lower cap (B) and the X-ring from the shock body.

4. Use side cutters to grip the shock shaft just above the rod end (C).
Remove the rod end from the shock shaft using the suspension
multi-tool (C).

5. Remove the shock shaft with piston from the shock body
out through the top of the shock body.

Shock assembly

Replace the stock piston with desired optional

1.

piston. Be careful not to lose the small washer
located below the piston.

2. Position the new piston onto the shock shaft

above the small washer. Grip the threads
of the shaft with side cutters or needlenose
pliers and tighten the nut with the 4-way
wrench to secure the assembly.

Piston Installation/Removal

3. Insert the shock shaft assembly through the shock body until the

piston bottoms out.

4. Lubricate the shaft and X-ring with silicone oil.

5 Install the X-ring over the shaft and into the bore of the shock body.

6. Install the lower cap using the suspension multi-tool (B).

7. Slide the bump stop onto the shaft.

8. Grip the shaft close to the threads with needlenose pliers or side

cutters and thread the rod end onto the shock shaft until the rod
end bottoms out (C).

9. Fill the shock with new silicone shock oil up to the top of the

shock body. Slowly move the piston up and down (always keeping
it submerged

in oil) to release the air bubbles. Let the shock sit for a

few minutes to allow any remaining air bubbles to surface.

10. Slowly thread the upper cap with the installed shock bladder onto

the shock body with the suspension multi-tool (A). The excess oil
will bleed out of the small hole in the shock cap. Tighten the shock
cap until snug. Use the included steel shock wrench to hold onto
the shock body while tightening.

11. Reinstall the spring and lower retainer.

ALIGNMENT SETTINGS

The alignment settings are critical for
optimizing the performance of Summit.
Adjust your alignment as carefully and
precisely as you possibly can.

Toe Adjustment

The wheels can be adjusted to point
straight ahead or have a toe-in or toe­out setting. To help you remember,
look down at your feet. For toe-in, your
feet point towards each other. For
toe-out, your feet point away from
each other. The
front wheels can be adjusted by
varying the length of the toe links
that connect the steering linkage to
the front axle carriers. The toe angle
of the rear wheels can be adjusted
by varying the length of the metal
toe links that connect the rear
bulkheads to the rear axle carriers.
The front toe links and rear toe
links are equipped with turnbuckles. The lengths of the toe links can be
adjusted by turning them with the included 5mm Traxxas wrench.

Toe Base Factory Settings
Front: 0-degrees
Rear: 1-degree toe-in each side

Static Camber Adjustment

The wheels can be set to have either
positive or negative camber (see illustration
below). The camber angle changes as the
wheel moves up and down through its
range of travel. Static camber is the camber
angle at the wheel when the vehicle is set
at its normal, stationary ride height.

The suspension pivot balls located in the axle carriers adjust the static
camber. The pivot balls are protected by blue dust plugs. To adjust your
static camber, insert the supplied 2.5 mm hex wrench through the slit
in the dust plug and engage the end of the pivot ball (compressing the
suspension until the arms are parallel to the ground will allow for easier

toe angle of the

Left-Hand

Threads

Right-Hand

(Normal) Threads

Decrease

Length

Increase

Length

Shock Piston Hole Sizes

1

1

1

Piston 1: 1.10 mm

2

2

2

Piston 2: 1.00 mm

3

3

3

Piston 3: 0.95 mm

Never slide the threads on
the shock rod past the X-ring
seal when it is installed and
compressed by the bottom
cap of the shock. Doing so will
damage the seal and cause
shock oil to leak.

SUMMIT • 23

TUNING ADJUSTMENTS

To achieve a good starting
point for the slipper clutch,
tighten the slipper clutch
adjusting nut clockwise until
the slipper clutch adjusting
spring fully collapses (do
not over tighten), and then
turn the slipper clutch nut
counterclockwise ¼ to ½ turn.

Use higher viscosity
(thicker) diff oil for:

More power to the wheels

•
with the most traction

Racing on low-traction

•
smooth surfaces

Better performance for

•
climbing on uneven terrain

Using lower viscosity
(thinner) diff oil for:

• More power to the wheels
with least traction

• Racing on low-traction
rough surfaces

24 • SUMMIT

hex wrench engagement). The upper pivot ball is normally screwed
all the way in. Negative camber is achieved by screwing the pivot ball
of the lower control arm out. Note: When camber is changed, the toe
angle of the wheel has to be reset.

Static Camber Base Factory Settings
Front: 1-degree negative camber each side
Rear: 1-degree negative camber each side

Positive camber

Negative camber

Transmission Tuning

Adjusting the Slipper Clutch

The Summit is equipped with
an adjustable Torque Control
slipper clutch, which is built
into the large spur gear. The
purpose of the slipper clutch
is to regulate the amount of

Loosen

power sent to the rear wheels
to prevent tire spin. When it
slips, the slipper clutch makes a
high-pitch, whining noise.

The slipper clutch is integrated into the main spur gear on the
transmission. The

slipper clutch is adjusted using the spring-loaded
locknut on the slipper shaft and the supplied universal wrench.
To tighten or loosen the slipper nut, insert the 2.0mm hex wrench
into the hole in the end of the slipper shaft. This locks the shaft for
adjustments. Turn the adjustment nut clockwise to tighten (less
slippage) and counterclockwise to loosen (more slippage).

Tighten

Tuning The Sealed Gear Differentials

When T-Lock is activated, the Summit’s differentials are locked for
maximum traction when climbing or traversing loose terrain. When
T-Lock is deactivated, the Summit’s differentials are “open,” allowing
the left and right wheels to spin at different speeds while turning so the
tires do not scuff or skid. This decreases the truck’s turning radius and
increases steering performance.

The performance of the differentials can be tuned for different driving
conditions and performance requirements. The differentials are filled
with silicone differential fluid, and are sealed to maintain consistent
long-term performance. Changing the oil in the differential with either
lower or higher viscosity oil will vary the performance characteristics of
the differentials. Changing to a higher viscosity oil in the differential will
reduce the tendency for engine power to be transferred to the wheel
with the least traction. You may notice this when making sharp turns
on slick surfaces. The unloaded wheels on the inside of the turn have
the least traction and tend to spin up to extremely high rpms. Higher
viscosity (thicker) oil causes the differential to act like a limited-slip
differential, distributing more equal power to the left and right wheels.
Summit will generally benefit from higher viscosity oil when climbing,
rock crawling, or racing on low-traction surfaces. Note: Heavier oil will

allow power to be transferred even with one or more tires off the ground.
This can make the vehicle more likely to overturn.

From the factory, both of Summit’s differentials are filled with SAE
100,000W viscosity silicone oil. Only use silicone oil in the differentials.
Traxxas offers SAE 10,000W, 30,000W and 50,000W viscosity oil to tune
the action of the differentials. Lower-viscosity oil allows the differential
to operate more freely. If most of your driving is done at high speed or
on high-traction surfaces, filling the differentials with lower-viscosity
fluid may improve handling. The differentials must be removed from
the vehicle and disassembled to change/replace oil.

WHEELS AND TIRES

Many types of aftermarket tires and wheels can be adapted for
use on your model. Most will affect the overall width and the
suspension geometry of the model. The offsets and dimensions
designed into the model’s wheels are intentional; therefore,
Traxxas cannot recommend the use of other non-Traxxas wheels
with different specifications. The diameter of the wheels is an
innovative design, and there is a variety of different tires available
for you to experiment with in addition to the tires included on the

TUNING ADJUSTMENTS

model (listed in your parts list). Experimentation with different
types of tires is recommended to see which ones work the best on
the terrain where the model is run. When selecting tires, consider
the overall diameter and the rubber compound (hard or soft). If
the overall diameter of the tire is significantly increased, you will
need to use a smaller pinion gear to compensate for the larger tire.
Soft compound tires with many short spikes generally work better
on hard, dry surfaces. In loose dirt, a tire with large spikes should
perform better. See your parts list for accessory wheels and tires.

MOTORS AND GEARING

The Summit’s Titan™ 775 Motor has been carefully designed to
match the needs of the Summit. The Titan is made to run efficiently
at high voltage to provide more torque and longer run times. We
do not recommend converting the Summit to a typical low-voltage
setup using traditional 540 size motors. While these components
will physically fit into the Summit, the system will not run as
efficiently, losing power in the form of motor and battery heating.
The result will be shorter run times, high current draw, and extreme
battery and motor temperatures.

The Summit is equipped from the factory with a 68-tooth spur gear
and 14-tooth pinion gear. Summit has a large range of gearing,
making it suitable for many different types of applications and
environments. If you want more acceleration and less top speed,
use a smaller pinion gear (fewer teeth, higher numerical ratio). The
overall reduction is the number of turns the motor makes for one
revolution of the tire. Higher numerical ratios provide more torque,
lower numerical ratios provide more top speed. With the Titan 775

motor, do not use a pinion gear larger than 14-tooth with the
stock 68-tooth spur gear. Use the following formula to calculate

the overall ratio for combinations not listed on the gear chart:

To find High Gear :

# Spur Gear Teeth

# Pinion Gear Teeth

To find Low Gear :

# Spur Gear Teeth

# Pinion Gear Teeth

x 5.22 =

x 14.45 =

Final

Gear Ratio

Final

Gear Ratio

Adjusting Gear Mesh

Incorrect gear mesh is the most common
cause of stripped spur gears. Gear mesh
should be checked and adjusted anytime
a gear is replaced. Access the gears by
removing the single screw on the top
gear cover.

To set the gear mesh, cut a narrow strip of
notebook paper and run it into the gear
mesh of the motor. The motor is mounted
to an aluminum motor mount. Loosen
the single motor mount screw with the
provided 3mm wrench to slide the motor
mount. Slide the motor and pinion gear
into the spur gear. Retighten the motor
mount screw and then remove the strip of

Motor Mount

Screw

paper. You should be able to run a fresh
strip of paper through the gears without

Do Not Loosen

binding them.

Motor Installation

To access the motor, remove the gear
cover by removing the single screw on
the top of the gear cover. The motor
uses an aluminum mount for quick, easy
motor access and gearing adjustment.
To remove the motor, remove the single
large hex screw using the supplied 3mm
wrench. Then, rotate the motor and
mount to the side of the model and slide backward off the post.

In addition to the 4mm holes used to mount the Summit’s Titan
775 motor, the motor plate has additional holes that accept
standard 540 motors (or other motors that use 3mm screws
and 25mm mounting hole spacing). There are two sets of holes
provided for 540 motors. They are:

1. Low CG (center of gravity) installation (mounts the motor low to
the chassis for best handling performance)

2. High CG installation (mounts motor higher for more clearance
for larger motors or aftermarket heat sinks)

Gearing Compatibility Chart:

The chart below shows a full range
of gear combinations. This does NOT
imply that these gear combinations
should be used. Over-gearing
(bigger pinions, smaller spurs) can
overheat and damage the motor
and/or speed control.

High Gear

Spur Gear

62 65 68

12

26.96 28.26 29.57

13

24.89 26.09 27.29

14

23.11 24.23 25.34

15

Pinion Gear

21.57 22.61 23.65

16

20.22 21.20 22.18

17

19.03 19.95 20.87

18

17.97 18.84 19.71

Low Gear

Spur Gear

62 65 68

12

74.66 78.27 81.88

13

68.91 72.25 75.58

14

63.99 67.09 70.18

15

Pinion Gear

59.73 62.62 65.51

16

55.99 58.70 61.41

17

52.70 55.25 57.80

18

49.77 52.18 54.59

Stock factory gearing

For two 6- or 7-cell NiMH
batteries and 4S LiPo batteries

Not recommended

SUMMIT • 25

TUNING ADJUSTMENTS

26 • SUMMIT

DUAL SERVO STEERING SYSTEM

Summit uses dual-servo steering and a single heavy-duty servo saver for
powerful, responsive steering. To prevent unnecessary receiver battery
drain, it is important to make sure that the servos are “at rest” when the
steering is at neutral. If one servo is out of adjustment, then both servos
will work against each other, fighting to find center.

Adjusting The Steering System

1. Remove the servo horns and steering links from the servos.
Disconnect the steering links from the servo saver.

Adjust both steering links to

2.
be the exact same length
(31.7mm - use “Steering Link
Length Template” to
set length).

Switch on the power to the

3.
receiver and the transmitter.

Steering Link Length Template

4. Adjust the steering trim on the transmitter to the neutral “0” position.

5. Connect one end of a steering link to the steering
servo saver arm and the other end to the servo horn.

6. Position the steering servo saver arm
perpendicular to the centerline of the vehicle.

While holding the steering servo saver

7.
arm in the position mentioned in step
6, install the servo horn onto the servo
such that the steering link is parallel
with the centerline of the vehicle. This
will automatically set the servo horn at
the 7-degree offset shown in
the illustration.

the second servo horn on the other

8. Install
side following the same procedure.

If necessary, fine-tune the length of the second steering link to
eliminate any load on the steering system in the neutral position. If you
are using aftermarket servos, it is important to use servo horns designed
for Summit. Optional steering servo horns are sold separately for use
with non-Traxxas servos.

31.7mm

T-LOCK SERVO INSTALLATION

The Summit’s T-Lock differential control servos are installed and pre­set at the factory. If you need to remove the servos or the servo horns
for maintenance or cleaning, carefully note their orientation when you
reinstall them to make certain the T-Lock system operates properly.

Before reinstalling the spring-loaded servo horns, reset the servos’
output shafts to the “diffs open” position.

1. Switch the transmitter and receiver on and plug the T-Lock servos
into their correct positions on the receiver unit (see page 10).

2. Operate the transmitter’s T-Lock switch to make certain both servos
operate properly, then place the switch in the full-up position for
unlocked front and rear diffs (see page 18).

3. Install the servo horns as shown below. Switch the transmitter and
on-board electronics off before completing the installation.

Front Differential T-Lock Servo
Differential Open: Install the spring-loaded

servo horn so the spring slot is parallel to the
linkage and the bellcrank is pushed away from
the servo, as viewed in the photo.

Open

Differential Locked: Switch the transmitter

and receiver on. Move the T-Lock switch to the
middle position to lock the front differential.
Confirm that the servo’s output shaft turns
counterclockwise to rotate the servo horn to the
position shown, with the spring slot perpendicular

Locked

to the linkage and the bellcrank pulled toward the servo.

Rear Differential T-Lock Servo
Differential Open: Install the spring-loaded servo

horn so the spring slot is parallel to the linkage
and the bellcrank is pulled toward the servo, as
viewed in the photo.

Differential Locked: Switch the transmitter and

Open

receiver on. Move the T-Lock switch to the bottom
position to lock the rear differential. Confirm that
the servo’s output shaft turns counterclockwise to
rotate the servo horn to the position shown, with
the spring slot perpendicular to the linkage and

Locked

the bellcrank pushed away from the servo.

Front of

Front of

Front of

Front of

Truck

Truck

Truck

Truck

MAINTAINING YOUR MODEL

Your model requires timely maintenance in order to stay in top
running condition. The following procedures should be taken

very seriously.

Inspect the vehicle for obvious damage or wear. Look for:

1. Cracked, bent, or damaged parts

2. Check the wheels and steering for binding.

3. Check the operation of the shock absorbers.

4. Check the wiring for any frayed wires or loose connections.

5. Check the mounting of the receiver and servo(s) and
speed control.

6. Check the tightness of the wheel nuts with a wrench.

7. Check the operation of the radio system, especially the
condition of the batteries.

8. Check for any loose screws in the chassis structure
or suspension.

9. Inspect the gears for wear, broken teeth, or debris lodged
between the teeth.

10. Check the tightness of the slipper clutch.

11. Check the tightness of the front pivot balls.

Other periodic maintenance:

• Slipper clutch pads (friction material):

Under normal use, the friction material in the slipper clutch
should wear very
slowly. If the thickness
of any one of the
slipper clutch pads
is 1.8mm or less, the
friction disc should
be replaced. Measure the
pad thickness using calipers
or measuring against the diameter
of the 1.5 and 2.0mm hex wrenches
provided with the model.

• Chassis: Keep the chassis clean of accumulated dirt and grime.

Periodically inspect the chassis for damage.

• Motor: Every 10-15 runs, remove, clean, and lubricate the motor.
Use a product such as electric motor cleaning spray to flush dirt
out of the motor. After cleaning, lubricate the bushings at each
end of the motor with a drop of light-weight electric motor oil.

• Shocks: Keep the oil level in the shocks full. Use only 100%
pure silicone shock oil to prolong the life of the seals. If you are
experiencing leakage around the top of the shock, inspect the
bladder in the top cap for signs of damage or distortion from
overtightening. If the bottom of the shock is leaking, then it
is time for a rebuild. The Traxxas rebuild kit for two shocks is
part #5462.

• Suspension: Periodically inspect the model for signs of damage,
such as bent or dirty suspension pins, bent turnbuckles, loose
screws, and any signs of stress or bending. Replace components
as needed.

• Driveline: Inspect the driveline for signs of wear such as worn
drive yokes, dirty axle half shafts, and any unusual noise or
binding. Remove the gear cover. Inspect the spur gear for wear
and check the tightness of the set screw in the pinion gear.
Tighten, clean, or replace components as needed.

Storage

When you are through running the model for the day, blow it off
with compressed air or use a soft bristled paint brush to dust-off
the vehicle. Always disconnect and remove the batteries from the
model whenever the model is stored. If the model will be stored for
a long time, then also remove the batteries from the transmitter.

If you have questions or need technical assistance, call Traxxas at

1-888-TRAXXAS

(1-888-872-9927) (U.S. residents only)

Always wear eye protection
when using compressed
air or spray cleaners and
lubricants.

10

SUMMIT • 27

TQi ADVANCED TUNING GUIDE

Starting Over:

Restoring Factory Defaults

When programming your
TQi transmitter, you may feel
the need to start over with
a clean slate. Follow these
simple steps to restore the
factory settings:

1. Turn the transmitter off.

2. Hold both MENU and SET.

3. Turn the transmitter on.

4. Release MENU and SET.
The transmitter LED will
blink red.

5. Press SET to clear settings.
The LED will turn solid
green and the transmitter
is restored to default.

Throttle Trim Seek Mode

When the Multi-Function knob is
set to throttle trim, the transmitter
remembers the throttle trim
setting. If the throttle trim knob
(Multi-Function knob) is moved
from the original setting while
the transmitter is off, or while the
transmitter was used to control
another model, the transmitter
ignores the actual position of
the trim knob. This prevents the
model from accidentally running
away. The LED on the face of the
transmitter will rapidly blink green
and the throttle trim knob (Multi­Function knob) will not adjust the
trim until it is moved back to its
original position saved in memory.
To restore throttle trim control,
simply turn the Multi-Function
knob either direction until the LED
stops blinking.

28 • SUMMIT

Your Traxxas transmitter has a programmable

Multi-Function knob
that can be set to control various advanced transmitter functions (set to
Steering Sensitivity by default, see page 15). Accessing the programming
menu is done by using the menu and set buttons on the transmitter and
observing signals from the LED. An explanation of the menu structure
follows on page 30. Experiment with the settings and features to see if
they can improve your driving experience.

Throttle Sensitivity (Throttle Exponential)

The Multi-Function knob can be set to control Throttle Sensitivity.
Throttle Sensitivity works the same way as Steering Sensitivity, as
described on page 15, but applies the effect to the throttle channel.
Only forward throttle is affected; brake/reverse travel remains linear
regardless of the Throttle Sensitivity setting.

Steering Percentage (Dual-Rate)

The Multi-Function knob can be set to control the amount (percentage)
of servo travel applied to steering. Turning the Multi-Function knob
fully clockwise will deliver maximum steering throw; turning the
knob counterclockwise reduces steering throw (Note: turning the dial
counterclockwise to its stop will eliminate all servo travel). Be aware that
the steering End Point settings define the servo’s maximum steering
throw. If you set Steering Percentage to 100% (by turning the Multi­Function knob fully clockwise), the servo will travel all the way to its
selected end point, but not past it. Many racers set Dual-Rate so they
have only as much steering throw as they need for the track’s tightest
turn, thus making the model easier to drive throughout the rest of the
course. Reducing steering throw can also be useful in making a model
easier to control on high-traction surfaces, and limiting steering output
for oval racing where large amounts of steering travel are not required.

Braking Percentage

The Multi-Function knob may also be set to control the amount of brake
travel applied by the servo in a nitro-powered model. Electric models do
not have a servo-operated brake, but the Braking Percentage function
still operates the same way in electric models. Turning the Multi-Function
knob full clockwise will deliver maximum brake throw; turning the
knob counterclockwise reduces brake throw (Note: Turning the dial
counterclockwise to its stop will eliminate all brake action).

Throttle Trim

Setting the Multi-Function knob to serve as throttle trim will allow you
to adjust the throttle’s neutral position to prevent unwanted brake drag
or throttle application when the transmitter trigger is at neutral. Note:
Your transmitter is equipped with a Throttle Trim Seek mode to prevent
accidental runaways. See the sidebar for more information.

Steering and Throttle End Points

The TQi transmitter allows you to choose the limit of the servo’s travel
range (or its “end point”) independently for left and right travel (on the
steering channel) and throttle/brake travel (on the throttle channel).
This allows you to fine-tune the servo settings to prevent binding
caused by the servo moving steering or throttle linkages (in the case
of a nitro model) farther than their mechanical limits. The end point
adjustment settings you select will represent what you wish to be the
servo’s maximum travel; the Steering Percentage or Braking Percentage
functions will not override the End Point settings.

Steering and Throttle Sub-Trim

The Sub-Trim function is used to precisely set the neutral point of the
steering or throttle servo in the event that simply setting the trim knob
to “zero” does not completely center the servo. When selected, Sub-Trim
allows finer adjustment to the servo output shaft’s position for precise
setting of the neutral point. Always set the Steering Trim knob to zero
before making final adjustment (if required) using Sub-Trim. If Throttle
Trim has been previously adjusted, the Throttle Trim will need to be
reprogrammed to “zero” before making final adjustment using Sub-Trim.

Setting Lock

Once you’ve adjusted all of these settings the way you like them, you
may want to disable the Multi-Function knob so none of your settings
can be changed. This is especially handy if you operate multiple vehicles
with a single transmitter via Traxxas Link

™

Model Memory.

Multiple Settings and the Multi-Function Knob

It is important to note that settings made with the Multi-Function
knob are “overlaid” on top of each other. For example, if you assign the
Multi-Function to adjust Steering Percentage and set it for 50%, then
reassign the knob to control Steering Sensitivity, the transmitter will
“remember” the Steering Percentage setting. Adjustments you make
to Steering Sensitivity will be applied to the 50% steering throw setting
you selected previously. Likewise, setting the Multi-Function knob to
“disabled” will prevent the knob from making further adjustments, but
the last setting of the Multi-Function knob will still apply.

TRAXXAS LINK MODEL MEMORY

Traxxas Link Model Memory is an exclusive, patent-pending feature
of the TQi transmitter. Each time the transmitter is bound to a new
receiver, it saves that receiver in its memory, along with all the settings
assigned to that receiver. When the transmitter and any bound receiver
are switched on, the transmitter automatically recalls the settings for
that receiver. There is no need to manually select your vehicle from a list
of model memory entries.

TQi ADVANCED TUNING GUIDE

Model Lock

The Traxxas Link Model Memory feature can store up to thirty models
(receivers) in its memory. If you bind a thirty-first receiver, Traxxas Link
Model Memory will delete the “oldest” receiver from its memory (in
other words, the model you used the longest time ago will be deleted).
Activating Model Lock will lock the receiver in memory so it cannot be
deleted.

You may also bind multiple TQi transmitters to the same model, making
it possible to pick up any transmitter and any previously bound model
in your collection and simply turn them on and drive. With Traxxas Link
Model Memory, there is no need to remember which transmitter goes
with which model, and there is never a need to have to select any model
from a list of model memory entries. The transmitter and receiver do it
all for you automatically.

To activate Model Lock:

1. Switch on the transmitter and receiver you wish to lock.

2. Press and hold MENU. Release when the status LED blinks green.

3. Press MENU three times. The status LED will blink green four
times repeatedly.

4. Press SET. The status LED will blink green in single-flash intervals.

5. Press SET once. The status LED will blink red once repeatedly.

6. Press MENU once. The status LED will blink red twice repeatedly.

7. Press SET. The LED will blink rapidly green. The memory is now locked.
Press and hold MENU to return to driving mode.

Note: To unlock a memory, press SET twice at step 5. The LED will

blink rapidly green to indicate the model is unlocked. To unlock all
models, press MENU twice at step 6 and then press SET.

To delete a model:

At some point, you may wish to delete a model you no-longer drive
from the memory.

1. Switch on the transmitter and receiver you wish to delete.

2. Press and hold MENU. Release when the status LED blinks green.

3. Press MENU three times. The status LED will blink green four
times repeatedly.

4. Press SET once. The status LED will blink green once repeatedly.

5. Press MENU once. The status LED will blink green twice repeatedly.

6. Press SET. The memory is now selected to be deleted. Press SET to
delete the model. Press and hold MENU to return to driving mode.

TRANSMITTER LED CODES

LED Color / Pattern Name Notes

Solid green Normal Driving Mode See page 13 for information on how to use your transmitter controls.

Slow red (0.5 sec on / 0.5 sec off) Binding See page 15 for more information on binding.

Flashing fast green (0.1 sec on / 0.15 sec off) Throttle Trim Seek Mode

Flashing medium red (0.25 sec on / 0.25 sec off) Low Battery Alarm Put new batteries in the transmitter. See page 11 for more information.

Flashing fast red (0.125 sec on / 0.125 sec off) Link Failure / Error

Programming Patterns

or

Counts out number (green or red), then pauses Current menu position See Menu Tree for more information.

x

Fast green 8 times Menu setting accepted (on SET)

8

Fast red 8 times Menu SET invalid User error, such as trying to delete a locked model.

x

8

RECEIVER LED CODES

LED Color / Pattern Name Notes

Solid green Normal Driving Mode See page 13 for information on how to use your transmitter controls.

Slow red (0.5 sec on / 0.5 sec off) Binding See page 15 for more information on binding.

Flashing fast red (0.125 sec on / 0.125 sec off) Fail-Safe / Low Voltage Detect

Turn the Multi-Function knob right or left until the LED stops flashing.
See page 28 for more information.

Transmitter and receiver are no longer bound. Turn the system off and then
back on to resume normal operation. Find source of the link failure (i.e., out of
range, low batteries, damaged antenna).

Consistent low voltage in the receiver triggers Fail-Safe so there is enough
power to center the throttle servo before it completely loses power.

Failsafe

Your Traxxas radio system is
equipped with a built-in failsafe
function that returns the throttle
to its last saved neutral position
in the event of a signal loss. The
LED on the transmitter and on the
receiver will rapidly flash red.

In order to re-acquire the signal
after the failsafe has activated,
you will need to walk a longer
distance closer to the model than
the distance the model travelled
out of range. Simply keep walking
towards the model until you re­acquire the signal.

SUMMIT • 29

TQi ADVANCED TUNING GUIDE

MENU TREE

The Menu Tree below shows how to navigate through
the TQi transmitter’s various settings and functions.
Press and hold MENU to enter the Menu Tree, and use
the following commands to navigate through the menu
and select options.

MENU: When you enter a menu, you always start at the

top. Press MENU to move down the Menu Tree.
When you reach the bottom of the tree, pressing
MENU again will return you to the top.

SET: Press SET to move across the Menu Tree and select

options. When an option is committed to the
transmitter’s memory, the status LED will rapidly
blink green.

BACK: Press both MENU and SET to go back one level in

the Menu Tree.

EXIT: Press and hold MENU to exit programming.

Your selected options will be saved.

ECHO: Press and hold SET to activate the “echo” function.

Echo will “play back” your current position on the
Menu Tree should you lose your place. For example:
If your current position is Steering Channel End
Points, holding SET will cause the LED to blink green
twice, green once, and then red three times. Echo
will not alter your adjustments or change your
position in the programming sequence.

Below is an example of how to access a function in the Menu
Tree. In the example, the user is setting the Multi-Function knob
to be a steering dual-rate control.

To set the Multi-Function knob to control STEERING DUAL-RATE (%):

1. Switch the transmitter on.

2. Press and hold MENU until the green LED lights. It will blink in single
intervals.

3. Press SET. The red LED will blink in single intervals to indicate Steering
Dual-Rate has been selected.

4. Press MENU twice. The red LED will blink three times repeatedly to
indicate Steering Percentage has been selected.

5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.

6. Press and hold MENU to return to driving mode.

Restoring Factory Defaults:

Transmitter

OFF

Hold both

MENU and SET

Transmitter ONRelease MENU and SET

red LED blinks

solid green. Transmitter is restored to default

30 • SUMMIT

Enter Programming

Press and hold
MENU for 3 seconds

Multi-Function Knob

1

One Blink Green

Press

MENU

Channel Setup

2

Two Blinks Green

Press

MENU

Mode Selection

3

Three Blinks Green

Press

MENU

Traxxas-Link

4

Four Blinks Green

Press SET to clear settings. LED will turn

Press

SET

Press

SET

Press

SET

Press

SET

Press MENU to move through options.
Press SET to select an option.

Steering Sensitivity (Expo)

1

One Blink Red

Throttle Sensitivity (Expo)

2

Two Blinks Red

Steering % (Dual-Rate)

3

Three Blinks Red

Braking %

4

Four Blinks Red

Throttle Trim

5

Five Blinks Red

Knob Disabled

6

Six Blinks Red

Steering (Channel 1)

1

One Blink Green

Press

MENU

Throttle (Channel 2)

2

Two Blinks Green

Press SET to select an option.

Electric

1

One Blink Red

Press

MENU

Nitro

2

Two Blinks Red

Model Locking

1

One Blink Green

Press

MENU

Delete Model

2

Two Blinks Green

Press

SET

Press

SET

Press

SET

Press

SET

Note: The transmitter is “live” during programming so
you can test the settings real time without having to
exit the Menu Tree.

Press MENU to move through options.
Press SET to select an option.

Servo Reversing

1

One Blink Red

Sub-Trim

2

Two Blinks Red

End Points

3

Three Blinks Red

Turn left to desired end point and press set to save.
To reset max throw: Let go of controls and press SET.

Reset End Points

4

Four Blinks Red

Servo Reversing

1

One Blink Red

Sub-Trim

2

Two Blinks Red

End Points

3

Three Blinks Red

forward to desired end point and press set to save.
To reset max throw: Let go of controls and press SET.

Reset End Points

4

Four Blinks Red

Unlock

1

One Blink Red

Lock

2

Two Blinks Red

Unlock All

3

Three Blinks Red

Confirm Deletion

1

One Blink Red

Press SET to reverse
servo direction.

Use knob to adjust
sub-trim. Press SET to save.

Use steering wheel to
adjust. Turn right to desired
end point, press set to save.

Press SET to restore factory
default end points.

Press SET to reverse
servo direction.

Use knob to adjust sub­trim. Press SET to save.

Use trigger to adjust. Pull
back to desired end point,
press set to save. Push

Press SET to restore factory
default end points.

Set Multi-Function
knob for STEERING
SENSITIVITY (Expo)

Set Multi-Function
knob for THROTTLE
SENSITIVITY (Expo)

Set Multi-Function
knob for STEERING
DUAL-RATE (%)

Set Multi-Function
knob for BRAKING
PERCENTAGE (%)

Set Multi-Function
knob for
THROTTLE TRIM

To LOCK the
Multi-Function knob

To REVERSE
the direction of
STEERING servo

To set the SUB TRIM
of the STEERING
servo

To set the END
POINTS of the
STEERING servo

To reset the END
POINTS of STEERING
servo to defaults

To REVERSE
the direction of
THROTTLE servo

To set the SUB TRIM
of the THROTTLE
servo

To set the END
POINTS of the
THROTTLE servo

To reset the END
POINTS of THROTTLE
servo to defaults

To REVERSE the
direction of SHIFT
servo

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

x

Press MENU

green LED blinks (x2)

Press SET to confirm

green LED blinks (x8)

Press MENU to confirm

red LED blinks (x2)

Press MENU twice

red LED blinks (x3)

Press MENU 3 times

red LED blinks (x4)

Press MENU 4 times

red LED blinks (x5)

Press MENU 5 times

red LED blinks (x6)

2

2

2

2

2

2

2

2

2

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

Press SET

green LED blinks

x

8

returns to driving mode

x

2

x

3

x

4

x

5

x

6

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press MENU

Press MENU

Press MENU

Press MENU

x

x

x

x

x

x

x

x

x

x

Press/hold MENU

Press SET to select

green LED blinks (x8)

Press SET to select

green LED blinks (x8)

Press SET to select

green LED blinks (x8)

Press SET to select

green LED blinks (x8)

Press SET to lock

green LED blinks (x8)

green LED blinks (x2)

green LED blinks (x2)

green LED blinks (x2)

green LED blinks (x2)

Press MENU twice

green LED blinks (x3)

8

Press/hold MENU

returns to driving mode

8

Press/hold MENU

returns to driving mode

8

Press/hold MENU

returns to driving mode

8

Press/hold MENU

returns to driving mode

8

Press/hold MENU

returns to driving mode

Press SET to reverse

red LED blinks (x2)

Press MENU twice

red LED blinks (x3)

Press MENU 3 times

red LED blinks (x4)

2

2

2

2

3

servo direction

Press MENU

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

Press SET

red LED blinks

x

8

x

2

x

3

x

4

Adjust the Multi-

Function knob until the

LED turns solid green.

Press/hold MENU

returns to driving mode

Use Multi-Function
knob to set neutral

Turn steering

wheel to desired max

left and right travel

x

Press SET

to reset end points

x

Press SET to reverse

servo direction

x

Press MENU

red LED blinks (x2)

x

Press MENU twice

red LED blinks (x3)

x

Press MENU 3 times

red LED blinks (x4)

x

Press SET to reverse

servo direction

to save each position

8

returns to driving mode

8

returns to driving mode

2

3

trigger to set desired
max throttle or brake

4

green LED blinks (x8)

8

returns to driving mode

MENU TREE FORMULAS

To select functions and make adjustments to the TQi transmitter without
referencing the Menu Tree, turn your transmitter on, find the function in the
left column you wish to adjust, and simply follow the corresponding steps

1

Always turn your

transmitter on first.

x

8

Press SET

to save position

x

Press SET

Press/hold MENU

Press/hold MENU

Use Multi-Function
knob to set neutral

Use throttle

x

Press SET

Press/hold MENU

Press/hold MENU

returns to driving mode

8

Turn steering wheel

Press SET to save

Use trigger to test

8

Press/hold MENU

returns to driving mode

to test settings

Press SET

to save position

returns to driving mode

x

8

returns to driving mode

returns to driving mode

IF END POINTS

ARE OK:

Press/hold MENU

Press/hold MENU

IF END POINTS

ARE OK:

Press/hold MENU

IF END POINTS

NEED TO BE

CHANGED:

and repeat steps 6-8

IF END POINTS

NEED TO BE

CHANGED:

and repeat steps 7-9

SUMMIT • 31

Press SET

Press SET

.

TQi ADVANCED TUNING GUIDE

The Traxxas Link
Wireless Module is sold
separately (part #6511). The
Traxxas Link application is
available from the Apple
App store for iPhone,
iPad, or iPod touch mobile
devices. iPhone, iPad, or
iPod touch are not included
with the Traxxas Link
Wireless Module.

For more information about
the Traxxas Link Wireless
Module and the Traxxas
Link application, visit
Traxxas.com.

32 • SUMMIT

PROGRAMMING YOUR TQi TRANSMITTER WITH

YOUR APPLE iPHONE, iPAD, OR iPOD TOUCH

The Traxxas Link Wireless Module
(part #6511, sold separately) for the
TQi transmitter installs in minutes to
transform your Apple® iPhone®, iPad®,
or iPod touch® into a powerful tuning
tool that allows you to replace the
transmitter’s button/LED programming
system with an intuitive, high-definition,
full-color graphical user interface.

Traxxas Link

The powerful Traxxas Link app (available in the Apple App Store) gives you
complete control over the operation and tuning of your Traxxas model
with stunning visuals and absolute precision. Install Traxxas Link telemetry
sensors on the model, and Traxxas Link displays real-time data such as
speed, RPM, temperature, and battery voltage.

Compatible with:
iPod touch (5th generation and later)
iPad (3rd generation and later)
iPad mini

iPhone 4S
iPhone 5
iPhone 5C
iPhone 5S

iPhone, iPad, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

Intuitive iPhone
and iPod touch interface

Traxxas Link makes it easy to
learn, understand, and access
powerful tuning options. Control
Drive Effects settings such as
steering and throttle sensitivity;
steering percentage; braking
strength; and throttle trim by
simply touching and dragging
the sliders on the screen.

Tap and slide to adjust Steering Sensitivity,

Throttle Trim, Braking Percent, and more!

Real-Time Telemetry

When you equip your model
with sensors, the Traxxas Link
dashboard comes to life showing
you speed, battery voltage, RPM,
and temperature. Set threshold
warnings and log maximums,
minimums, or averages. Use the
recording function to document
your dashboard view, with
sound, so that you can keep
your eyes on your driving and

The customizable Traxxas Link dashboard delivers

real-time rpm, speed, temperature, and voltage data.

not miss a single apex.

Manage up to 30 Models with Traxxas Link

The TQi radio system
automatically keeps track of
what vehicles it has bound to
and what settings were used
for each--up to 30 models total!
Traxxas Link provides a visual
interface to name the models,
customize their settings, attach
profiles, and lock them into
memory. Simply choose a model
and any previously bound

Traxxas Link Model Memory simplifies organizing

transmitter, power them up,
and start having fun.

your collection of vehicles.

SUMMIT • 33

141230 56076-1-OM-N-EN-R00

owner’s manual

MODEL 56076-1

6200 Traxxas Way McKinney, Texas 75070

1-888-TRAXXAS