Trane 4TVE0007B100NB, 4TVE0009B100NB, 4TVE0012B100NB Installation and Maintenance Manual

Installation, Operation, and Maintenance

Variable Refrigerant Flow System

1-Way Cassette Indoor Unit Series

Models: 4TVE0007B100NB, 4TVE0009B100NB, 4TVE0012B100NB

SAFETY WARNING

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment.

February 2013 VRF-SVX27A-EN

DB68-03799A(1)

Introduction

Read this manual thoroughly before operating or servicing this unit.

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as required. Your personal safety and the proper operation of this machine depend upon the strict observance of these precautions.

The three types of advisories are defined as follows:

WARNING

CAUTIONs

NOTICE

Important Environmental Concerns

Scientific research has shown that certain man-made chemicals can affect the earth’s naturally occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all refrigerants containing these compounds have the same potential impact to the environment. Trane advocates the responsible handling of all refrigerantsincluding industry replacements for CFCs such as HCFCs and HFCs.

Important Responsible Refrigerant Practices

Trane believes that responsible refrigerant practices are important to the environment, our customers, and the air conditioning industry. All technicians who handle refrigerants must be certified. The Federal Clean Air Act (Section 608) sets forth the requirements for handling, reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in these service procedures. In addition, some states or municipalities may have additional requirements that must also be adhered to for responsible management of refrigerants. Know the applicable laws and follow them.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It could also be used to alert against unsafe practices.

Indicates a situation that could result in equipment or property-damage only.

WARNING

Proper Field Wiring and Grounding Required!

Failure to follow code could result in death or serious injury. All field wiring MUST be performed by qualified personnel. Improperly installed and grounded field wiring poses FIRE and ELECTROCUTION hazards. To avoid these hazards, you MUST follow requirements for field wiring installation and grounding as described in NEC and your local/state electrical codes.

WARNING

Personal Protective Equipment (PPE) Required!

Failure to wear proper PPE for the job being undertaken could result in death or serious injury. Technicians, in order to protect themselves from potential electrical, mechanical, and chemical hazards, MUST follow precautions in this manual and on the tags, stickers, and labels, as well as the instructions below:

• Before installing/servicing this unit, technicians MUST put on all PPE recommended for the work being undertaken. ALWAYS refer to appropriate MSDS sheets and OSHA guidelines for proper PPE.

• When working with or around hazardous chemicals, ALWAYS refer to the appropriate MSDS sheets and OSHA guidelines for information on allowable personal exposure levels, proper respiratory protection, and handling recommendations.

• If there is a risk of arc or flash, technicians MUST put on all PPE in accordance with NFPA 70E or other country-specific requirements for arc flash protection, PRIOR to servicing the unit.

This document and the information in it are the property of Trane and may not be used or reproduced in whole or in part, without the written permission of Trane. Trane reserves the right to revise this publication at any time and to make changes to its content without obligation to notify any person of such revision or change.

Trademarks

All trademarks referenced in this document are the trademarks of their respective owners.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings, Cautions, and Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Model Number Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Location Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Service Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mounting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Purging the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installing Refrigerant Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Leak Testing Pipe Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installing the Drain System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Important Environmental Concerns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Responsible Refrigerant Practices . . . . . . . . . . . . . . . . . . . . . . . 2

Centralized Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Testing the Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Refrigerant Pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Drainage Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Wiring the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Electronic Expansion Valve (EEV) Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Electrical Conduit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Using the VRF Wireless Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

The 2-Digit Segments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Configuration Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Mode 2: Option Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Mode 5: Option Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Mode A: Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Mode d: Specific Digit Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Internal Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

VRF-SVX27A-EN 3

Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Operating Mode for Heat Pump Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning the Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning the Grill and Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Periodic Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Warranty For Trane Advantage™ VRF Systems and Related Accessories . . . 39

Basic Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Exclusions and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4 VRF-SVX27A-EN

Model Number Description

4 T V D 0 0 1 8 A 1 0 0 N A 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Digit 1: Refrigerant

4 = R410A

Digit 2: Brand name

T = Trane

Digit 3: System type

V = Variable Refrigerant Flow

Digit 4: Configuration Type (also see separate tab)

B = mini 4-way cassette L = Slim duct type (low pressure) C = 4-way cassette A = HSP duct type high pressure) D = MSP duct type (mid-pressure) X = Ceiling E = 1-way cassette W = High-wall

Digit 5: Reserved for future use

0 = Not currently used

Digit 6, 7, 8: Nominal capacity (Btu/h x 1,000)

006 = 6,00 0 Btu/h

007 = 7,000 Btu/h 024 = 24,000 Btu/h 068 = 68,000 Btu/h

009 = 9,00 0 Btu/h 030 = 30,000 Btu/h

012 = 12,000 Btu/h 036 = 36,000 Btu/h 096 = 96,000 Btu/h 018 = 18,000 Btu/h

020 = 20,000 Btu/h

048 = 48,000 Btu/h

060 = 60,000 Btu/h

076 = 76,000 Btu/h

Digit 9: Major development sequence

B = Second development sequence

Digit 10: Electric power supply characteristics

1 = 220/60/1 B = 220–240/50/1

Digit 11: Reserved for future use

0 = Not currently used

Digit 12: Controller

0 = None

R = Remote control standard

W = Wired control standard

Digit 13: Region of sale

N = North America (UL or ETL)

Digit 14: Minor design sequence

A = First design sequence B = Second design sequence

VRF-SVX27A-EN 5

Preparing for Installation

Accessories

In addition to product literature, the following accessories are supplied with this unit. The type and quantity may differ, depending on the model.

Template Flexible hose Drain hose insulation

Location Considerations

When deciding on a location for the indoor unit, the following factors must be considered:

• The air inlet and outlet must be unobstructed.

• The wall or ceiling must support the weight of the unit.

• The wall or ceiling must not be subject to vibration.

• Pre-plan for easy and short routing of the refrigerant tubing and wiring to the outdoor unit.

• The air must circulate freely in the area to be cooled/heated.

• Sufficient clearance must be maintained around the unit.

• Condensate must be managed correctly and safety away from the unit.

• The unit should be installed in a way that prevents unauthorized access.

• The unit must not be installed in an area that is damp or could come into contact with water (such as a laundry room).

• The unit must not be exposed to direct sunshine or to other direct heat sources.

• The filter must be able to be removed and cleaned easily.

• The unit should be placed as far as possible from fluorescent lights so the remote control is not subject to interference.

• Care should be taken to prevent harmonics generated by loose or unsupported material in close proximity to a running unit.

• The unit must not be installed in an area that is exposed to salt, machine oil, sulfide gas, or corrosive environmental conditions.

Drain hose insulation

wrap

Conduit bracket Grommet

6 VRF-SVX27A-EN

Unit Dimensions

Unit: inch (mm)

40-3/16 (970)

45-1/4 (1150): Ceiling opening

Drain hole

16-1/8 (410)

19-11/16 (500)

1-9/16 (40)

2-1/16 (52)

40-3/4 (1036): suspension position

9-13/16 (249)

Suspension pos

17-5/16 (440)

Ceiling opening

47-3/16 (1198)

5-5/16

(135)

Ceiling

5-7/8 (150)

1 (25)

3-3/8 (85)

13/16 (21)

3-1/16 (77)

1-15/16 (50)

Preparing for Installation

VRF-SVX27A-EN 7

1 2 3 4 5 6

Gas pipe connection 1/2 (12.70

Liquid pipe connection 1/4 (6.35)

Drain pipe connection OD 1.14 (29), ID 0.98 (25)

Power supply connection —

Air discharge grille —

Air return grille —

Preparing for Installation

(

)

(

)

(

)

(

)

Service Clearances

8 VRF-SVX27A-EN

Installation

Ceiling support

Concrete

Pre-poured anchor

Drill hole for anchor

Field-supplied suspension bolts (M10 or 3/8 in.)

Isolator

Bracket

Review “Installation Considerations” before proceeding with installation.

Follow the procedures in these sections in the order given.

Note: Install the Y-joint before installing the indoor unit.

Mounting the Unit

If the ceiling is already constructed, piping must be laid into position before placing the unit inside the ceiling.

Avoid equipment damage and personal injury!

Ensure that the ceiling is strong enough to support the weight of the indoor unit. Before hanging the unit, test the strength of each of the attached suspension bolts.

To mount the unit:

1. Place the template on the spot where the unit is to be installed and mark the holes.

Note: The template may shrink or stretch slightly due to heat or humidity. Before drilling holes,

2. Determine the appropriate type of suspension bolts and anchors according to the ceiling type. Insert bolt anchors into existing ceiling supports (A) or construct a suitable support (B).

Installation

CAUTION

verify proper dimensions between the marks. Refer to “Installing the Front Panel” for final finishing clearances.

3. Install suspension bolts at all four locations.

4. Screw two nuts to each suspension bolt, leaving space between the nuts for hanging the unit.

Note: If the suspension bolts are longer than 59 in. [1.5 m]) or vibrations are a concern, place

isolators on the brackets to absorb vibrations.

5. Hang the unit by its support brackets between the two nuts.

6. If pad stoppers or isolators are used to absorb vibrations, place them on the brackets.

VRF-SVX27A-EN 9

Installation

Washers, isolators, or spacers

Threaded rod should not protrude more than

1.2 in (30 mm) below the top of the bracket

Gas refrigerant port

Liquid refrigerant port

7. Tighten the nuts to suspend the unit following the guidelines in the figure below.

8. Maintain proper spacing between the unit and the ceiling; refer to the following figure.

9. Adjust the level of the unit with a leveler.

Purging the Unit

The unit is shipped from the factory with a holding charge of nitrogen. All of this gas must be purged from the unit.

To purge the unit, open the cover and unscrew the pinch pipes from the ends of both gas and liquid refrigerant pipes. Make sure all gas has escaped before connecting the piping.

Note: To prevent dirt or foreign objects from getting into the pipes during installation, do not

remove the pinch pipes completely until you are ready to connect the piping.

10 VRF-SVX27A-EN

Installing Refrigerant Piping

Correct: 90º

Oblique

Rough

Burr

Connect field-supplied piping using flared connections (not supplied) or by brazing. The large unit port is for gas refrigerant; the small one is for liquid refrigerant.

Cut or extend field-supplied piping as needed. Use the following procedures.

System Failure!

If brazing is used for pipe connections, a nitrogen purge is required to prevent the formation of copper oxides inside the piping. Failure to follow this procedure could damage the system.

• Before connecting the pipes, make sure they are free of dirt and debris.

• Use insulated, unwelded, degreased, and deoxidized copper pipe (Cu-DHP type according to ISO 1337 or UNI EN 12735-1) suitable for an operating pressure of at least 609.15 psi (4200 kPa) and a burst pressure of at least 3002.28 psi (20,700 applications is unsuitable.

• For sizing and limits (height difference, line length, maximum bends, refrigerant charge, and so on) see the outdoor unit installation manual.

• All refrigerant connections must be accessible for servicing and maintenance.

Installation

NOTICE

kPa). Copper pipe for hydro-sanitary

Pipe Cutting

Required tools:

•Pipe cutter

•Reamer

• Pipe holder

1. Using a pipe cutter, cut the pipe so that the cut edge is at 90° to the side of the pipe.

2. Use a reamer to remove all burrs at the cut edge.

See examples of correctly and incorrectly cut pipes.

Flared Pipe Connections

VRF-SVX27A-EN 11

Clutch type and wing nut type flare tools are available for flared pipe connections.

Installation

Length of pipe extending above flare bar

Pipe

Flaring

bar

Yoke

Flaring bar

Copper pipe

Flare nut

Inclined

Damaged

surface

Uneven

thickness

Correct

Cracked

1. Slide the flare nut over the pipe to be flared.

2. Slide the end of the pipe into the hole on the flaring bar that fits the pipe, leaving a length of pipe, determined by tool type (see table), extending above the flaring bar. Clamp it down.

R-410A clutch type

Clutch type Wing nut type

Conventional flare tool

0–0.020 in. 0.04–0.06 in. 0.06–0.08 in.

3. Attach the yoke to the flaring bar, centering the conical part over the end of the pipe that is extending above the flaring bar.

4. Tighten the yoke securely to flare the end of the pipe.

5. Remove the pipe. The end of the pipe that you flared should look like the end of a trumpet. See examples of correctly and incorrectly flared pipes.

12 VRF-SVX27A-EN

+ 28 hidden pages