DC/DC Converter
|
|
|
|
|
TES 2 Series |
2 Watt |
|
|
|
|
|
||
|
|
|
|
|||
|
|
|
|
|
||
|
|
|
|
|
|
|
Features
Surface Mount DIL-Package
16 Standard Models
Regulated Output Voltage
I/O-isolation 1’000 VDC
Very low Output Noise
Indefinite Short-Circuit Protection
High Accuracy of Pin Co-Planarity
High Reliability, MTBF >800’000 h
Reflow Soldering to
CECC 00 802, Issue 2
2 Year Product Warranty
The TES 2 converter series is intended for all applications where PCB’s are assembled on an automated SMD production line.The small size DIL-package and the light weight allows easy handling by pick-and-place machines.
They offer a 1000 VDC I/O-isolation and internal filters to reduce reflected input ripple current and to guarantee low output noise.This product series provides an economical solution for many cost critical applications in industrial and consumer electronics.
Models
Ordercode |
Input voltage |
Output voltage |
Output current max. |
Efficiency typ. |
|
||
|
|
|
|
|
|
|
|
TES 2-0511 |
|
5 |
VDC |
400 |
mA |
60 % |
|
TES 2-0512 |
5 VDC ±10% |
12 |
VDC |
165 |
mA |
60 % |
|
TES 2-0522 |
± 12 |
VDC |
± 85 mA |
60 % |
|
||
|
|
||||||
TES 2-0523 |
|
± 15 |
VDC |
± 65 mA |
60 % |
|
|
|
|
|
|
|
|
|
|
TES 2-1211 |
|
5 |
VDC |
400 |
mA |
60 % |
|
TES 2-1212 |
12 VDC ±10% |
12 |
VDC |
165 |
mA |
60 % |
|
TES 2-1222 |
± 12 |
VDC |
± 85 mA |
60 % |
|
||
|
|
||||||
TES 2-1223 |
|
± 15 |
VDC |
± 65 mA |
60 % |
|
|
|
|
|
|
|
|
|
|
TES 2-2411 |
|
5 |
VDC |
400 |
mA |
60 % |
|
TES 2-2412 |
24 VDC ±10% |
12 |
VDC |
165 |
mA |
60 % |
|
TES 2-2422 |
± 12 |
VDC |
± 85 mA |
60 % |
|
||
|
|
||||||
TES 2-2423 |
|
± 15 |
VDC |
± 65 mA |
60 % |
|
|
|
|
|
|
|
|
|
|
TES 2-4811 |
|
5 |
VDC |
400 |
mA |
60 % |
|
TES 2-4812 |
48 VDC ±10% |
12 |
VDC |
165 |
mA |
60 % |
|
TES 2-4822 |
± 12 |
VDC |
± 85 mA |
60 % |
|
||
|
|
||||||
TES 2-4823 |
|
± 15 |
VDC |
± 65 mA |
60 % |
|
|
|
|
|
|
|
|
|
|
www.tracopower.com |
Page 1 |
DC/DC Converter
TES 2 Series 2 Watt
Input Specifications
Input current no load /full load |
5 Vin models |
80 |
mA / 665 mA typ. |
||
|
|
|
12 Vin models |
35 |
mA / 280 mA typ. |
|
|
|
24 Vin models |
17 |
mA / 140 mA typ. |
|
|
|
48 Vin models |
10 |
mA / 70 mA typ. |
|
|
|
|
||
Surge voltage (1 sec. max.) |
5 Vin models |
7.5 |
VDC max. |
||
|
|
|
12 Vin models |
15 |
VDC max. |
|
|
|
24 Vin models |
30 |
VDC max. |
|
|
|
48 Vin models |
55 |
VDC max. |
|
|
|
|||
Reverse voltage protection |
|
500 mA max. |
|||
|
|
|
|
|
|
Input Filter |
|
|
|
Pi-Filter |
|
|
|
|
|
||
Output Specifications |
|
|
|
||
Voltage set accuracy |
|
|
± 3 % |
||
|
|
|
|
||
Regulation |
– Input variation |
Vin min. to Vin max. |
± 0.3 % max. |
||
|
– Load variation 10 – 100 % |
± 0.5 % max. |
|||
|
|
– single output models |
|||
|
|
– dual output models balanced load |
± 3 % max. |
||
|
|
|
|||
Ripple and noise |
(20 MHz Bandwidth) |
50 mVpk-pk max. |
|||
|
|
|
|||
Temperature coefficient |
|
± 0.02 % / °C |
|||
|
|
|
|||
Output current limitation |
|
>120 % of Iout max., constant current |
|||
|
|
|
|||
Short circuit protection |
|
indefinite (automatic recovery) |
|||
|
|
||||
Capacitive load – single output models |
470 µF max. |
||||
|
– dual output models |
220 µF max. |
|||
|
|
|
|
||
General Specifications |
|
|
|
||
Temperature ranges |
– Operating |
|
– 40 °C ... + 60 °C (no derating) |
||
|
|
– Case temperature |
+ 95 °C max. |
||
|
|
– Storage |
|
– 40 °C ... + 125 °C |
|
|
|
|
|
|
|
Derating |
|
|
|
2.9% / °C above 60 °C |
|
|
|
|
|||
Humidity (non condensing) |
|
95 % rel H max. |
|||
|
|
||||
Reliability, calculated MTBF (MIL-HDBK-217 E) |
>800’000h @ + 25 °C |
||||
|
|
|
|
|
|
Isolation voltage |
|
Input/Output |
|
1’000VDC |
|
|
|
|
|
|
|
Isolation capacity |
|
Input/Output |
|
100 pF typ. |
|
|
|
|
|||
Isolation resistance |
Input/Output (500 VDC) |
> 1‘000 M Ohm |
|||
|
|
|
|
||
Switching frequency |
|
|
80 KHz typ. (depending on load) |
||
|
|
|
|
|
|
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
www.tracopower.com |
Page 2 |