TP-Link TL-PA7010P KIT Quick Installation Guide

Quick Installation Guide

Pair

* TL-PA7010P KIT (European version) is used for demonstration in this guide.

1000Mbps

Adapter

TL-PA7010P

Same Electrical Circuit

Adapter

TL-PA7010P

Same Electrical Circuit

More: To add additional Powerline adapters and extenders with the default

Wait until the Powerline LED turns on.

Note: If the LED is red or o, please refer to FAQ-Q2.

1000Mbps

settings, simply plug them into the wall sockets on the same electrical circuit.

1000Mbps

Router

WAN LAN

Attention

Plug powerline devices into wall outlets instead of power strips.

Wall Outlet Power Strip

Set Up a Secure Powerline Network by Pairing (Recommended)

You can create or join a secure powerline network using the Pair button on two devices at a time.

Tip: We recommend that you plug in the powerline devices near each other when pairing.

To create a secure powerline network:

Physical Appearance

Pair

Power LED Powerline LED Ethernet LED Pair Button

Press the Pair button on one of the powerline devices

for 1 second. Its Power LED starts blinking.

Note: If the Power LED does not blink, press the Pair button again.

Within 2 minutes, press the Pair button on another

device for 1 second. Its Power LED starts blinking.

When the Powerline LED turns on, it's done.

1000Mbps

To join an existing secure powerline network:

Press the Pair button on any of the existing powerline

devices for 1 second. Its Power LED starts blinking.

Note: If the Power LED does not blink, press the Pair button again.

Within 2 minutes, press the Pair button on the new

powerline adapter for 1 second. Its Power LED starts blinking.

When the Powerline LED turns on, it's done.

Existing

Powerline Device

1000Mbps

Pair

Blinking

Pair

Blinking

within 2 minutes

New

Powerline Device

Integrated

Blinking

Pair

1000Mbps

Electrical Socket

DESCRIPTIONLED STATU S

1000Mbps

Blinking

Pair

Power

Powerline

Ethernet

* Five minutes after the device connected to the powerline adapter is turned o or

inactive, the powerline adapter will automatically switch to Power-Saving Mode.

ITEM

1000Mbps

Pair Button

Integrated Electrical Socket

On/O

Blinking

Yellow-green

Red

O

On/O

DESCRIPTION

Press and hold for 1 second to set up or join a secure powerline network. Press and hold for more than 6 seconds to reset the powerline adapter.

Used as an electrical outlet expansion for power strip or household

appliances. It can remove some electrical noise that might aect powerline

performance.

The powerline adapter is on or o.

Once every second: Pairing is in process. Once every 3 seconds: Power-Saving Mode is on.*

The powerline adapter is in a location with a good signal strength. The powerline adapter is in a location with a poor signal strength. We recommend trying another wall socket. The powerline adapter is not connected to any powerline network.

The Ethernet port is connected or disconnected.

Frequently Asked Questions

Q1. How do I reset my powerline adapter?

A. With the powerline adapter plugged into an electrical outlet, press and hold

the Pair button for more than 6 seconds until the Power LED goes o

momentarily and then comes back on.

Q2. What should I do if the Powerline LED is red or o?

If the LED is red:

A. The powerline adapter is in a location with a poor signal strength. Try

another wall socket.

If the LED is o:

A1. Try another wall socket and make sure all powerline devices are on the same

electrical circuit.

A2. Try to set up a powerline network by pairing. Refer to the section above for

instructions.

A3. If the problem persists, contact our Technical Support.

Q3. What should I do if there is no internet connection in my

powerline network?

A1. Make sure all powerline devices are on the same electrical circuit. A2. Make sure the Powerline LEDs are lit on all of your powerline devices. If they are

not, pair all devices again.

A3. Make sure all devices are correctly and securely connected.

A4. Check if you have an internet connection by connecting the computer directly to

the modem or router.

Q4. What should I do if a successfully-paired powerline device does

not reconnect after it is relocated?

A1. Try another socket and make sure it is on the same electrical circuit.

A2. Try to pair the device again, and make sure the Powerline LED is on.

A3. Check for possible interference due to a washing machine, air conditioner or other

household appliance that may be too close to one of the powerline devices. Plug the appliance into the integrated electrical socket to remove the electrical noise if your powerline device has an integrated electrical socket.

Easy Management

Using tpPLC utility for advanced conguration:

1. Visit http://www.tp-link.com, and search for your product.

2. Find and download the compatible version of utility on its Support page.

3. Install the utility and start your conguration.

For technical support, the user guide and other information, please

visit http://www.tp-link.com/support, or simply scan the QR code.

TP-Link hereby declares that this device is in compliance with the essential requirements and other relevant

provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU. The original EU declaration

of conformity may be found at http://www.tp-link.com/en/ce.