TP-Link TL-PA411 Quick guide

AV600

WAN LAN

Same Electrical Circuit

Quick Installation Guide

* Images are for demonstration only.

Adapter

TL-PA411

Adapter

TL-PA411

Wait until the Powerline LED turns on.

Note: If the LED is not solid on, please refer to FAQ-Q2.

More: To add additional Powerline adapters and extenders with the default settings, simply plug them into the wall sockets on the same electrical circuit.

Router

Attention

Plug powerline devices into wall outlets instead of power strips.

Wall Outlet Power Strip

Set Up a Secure Powerline Network by Pairing (Recommended)

AV600

You can create or join a secure powerline network using the Pair button on two devices at a time.

Tip: We recommend that you plug in the powerline devices near each other when pairing.

To create a secure powerline network:

Press the Pair button on any of the powerline devices

for 1 second. The Power LED should start blinking.

Note: If the Power LED does not blink, press the Pair button again.

(Within 2 minutes) press the Pair button on another device

for 1 second. The Power LED should start blinking.

When the LED lights up, a powerline network has been

successfully created.

To join an existing secure powerline network:

Press the Pair button on any of the existing powerline devices

for 1 second. The Power LED should start blinking.

Note: If the Power LED does not blink, press the Pair button again.

(Within 2 minutes) press the Pair button on the new

powerline adapter for 1 second. The Power LED should start blinking.

When the LED lights up, a powerline network has

been successfully created.

Existing

Powerline Device

Blinking

Within 2 minutes

New

Powerline Device

Blinking

Physical Appearance

Power LED Powerline LED

AV600

Ethernet Port

DESCRIPTIONLED STATU S

Power

Powerline

Ethernet

* If the device connected to the adapter is turned o or inactive for more than 5

minutes, the powerline adapter will automatically switch to Power-Saving Mode.

Blinking

O

Blinking

O

On/O

The powerline adapter is on. Once every second: Pairing is in process. Once every 15 seconds: Power-Saving Mode is on.*

The powerline adapter is o.

The powerline adapter is successfully connected to a powerline network and is in a suitable location. The powerline adapter is in a location with a poor signal strength. We recommend trying another wall socket. The powerline adapter is not connected to any powerline network.

The Ethernet port is connected or not connected.

DESCRIPTIONITEM

Pair Button

Press for 1 second to set up or join a secure powerline network. Press and hold for more than 6 seconds to reset the powerline adapter.

Ethernet LED Pair Button

Frequently Asked Questions

Q1. How do I reset my powerline adapter?

A. With the powerline adapter plugged into an electrical outlet, press and hold

the Pair button for more than 6 seconds until the Power LED goes o

momentarily and then comes back on.

Q2. What should I do if the Powerline LED is not solid on?

If the LED is blinking:

A. The powerline adapter is in a location with a poor signal strength. Try another

wall socket.

If the LED is o:

A1. Try another wall socket and make sure all powerline devices are on the same

electrical circuit.

A2. Try to set up a powerline network by pairing. Refer to the section above for

instructions.

A3. If the problem persists, contact our Technical Support.

Q3. What should I do if there is no internet connection in my

powerline network?

A1. Make sure all powerline devices are on the same electrical circuit. A2. Make sure the Powerline LEDs are lit on all of your powerline devices. If they are

not, pair all devices again. A3. Make sure all devices are correctly and securely connected. A4. Check if you have an internet connection by connecting the computer directly to

the modem or router.

Q4. What should I do if a successfully-paired powerline device does

not reconnect after it is relocated?

A1. Try another socket and make sure it is on the same electrical circuit. A2. Try to pair the device again, and make sure the Powerline LED is on. A3. Check for possible interference due to a washing machine, air conditioner or other

household appliance that may be too close to one of the powerline devices. Plug

the appliance into the integrated electrical socket to remove the electrical noise if

your powerline device has an integrated electrical socket.

Easy Management

Using tpPLC utility for advanced conguration:

1. Visit https://www.tp-link.com, and search for your product.

2. Find and download the compatible version of utility on its Support page.

3. Install the utility and start your conguration.

Safety Information

Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. Plug the powerline devices directly into the wall outlets but not the power strips. The socket-outlet shall be installed near the equipment and shall be easily accessible.

For technical support, user manuals and more information, please visit https://www.tp-link.com/support, or simply scan the QR code.

TP-Link hereby declares that this device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.