TP Link TDW8951NDV6 User Manual
TD-W8951ND
150Mbps Wireless N ADSL2+ Modem Router
Rev: 5.0.0
1910010973
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1） This device may not cause harmful interference.
2） This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority to
operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”
Part 68 telecom statement
Customer Information
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the BOTTOM OF DEVICE is a label that contains,
among other information, a product identifier in the format US:
TPLDL01BTDW8951ND. If requested, this number must be provided to the
telephone company.
Applicable connector jack Universal Service Order Codes (“USOC”) for the
Equipment is RJ11C .
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
telephone company. For products approved after July 23, 2001, the REN for this
product is part of the product identifier that has the format US:
TPLDL01BTDW8951ND. The digits represented by 01B are the REN without a
decimal point (e.g., 03 is a REN of 0.3).
If this 150Mbps Wireless N ADSL2+ Modem Router causes harm to the
telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice isn't
practical, the telephone company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the telephone company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this 150Mbps Wireless N ADSL2+ Modem Router,
for repair or warranty information, please contact975 Overland Ct, San Dimas, CA
91773 at +1 626-333-0234. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect the equipment
until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission or corporation commission for
information.
If your home has specially wired alarm equipment connected to the telephone
line, ensure the installation of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak hours, such as early morning or late
evenings.
IC telecom statement
English version
''NOTICE: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration
number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating
that Industry Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment.”
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment
is 01B. The REN assigned to each terminal equipment provides an indication
of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed five.''
French version
« AVIS : Le présent matériel est conforme aux spécifications techniques
d’Industrie Canadaapplicables au matériel terminal. Cette conformité est
confirmée par le numérod'enregistrement. Le sigle IC, placé devant le numéro
d'enregistrement, signifie quel’enregistrement s’est effectué conformément à
une déclaration de conformité et indique queles spécifications techniques
d'Industrie Canada ont été respectées. Il n’implique pasqu’Industrie Canada a
approuvé le matériel. »
« AVIS : L'indice d'équivalence de la sonnerie (IES) du présent matériel est de
01B. L'IESassigné à chaque dispositif terminal indique le nombre maximal de
terminaux qui peuvent êtreraccordés à une interface téléphonique. La
terminaison d'une interface peut consister en unecombinaison quelconque de
dispositifs, à la seule condition que la somme d'indicesd'équivalence de la
sonnerie de tous les dispositifs n'excède pas 5. »
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射
頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
UkrSEPRO
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 150Mbps Wireless N ADSL2+ Modem Router
Model No.: TD-W8951ND
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.7.1: 2006
EN 301 489-1 V1.9.2:2011& EN 301 489-17 V2.2.1:2012
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN60950-1:2006+A11：2009+A1:2010+A12:2011
EN62311:2008
The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2014
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
CONTENTS
Package Contents .................................................................................................... 1
Chapter 1. Introduction ......................................................................................... 2
1.1 Product Overview ..................................................................................2
1.2 Main Features .......................................................................................2
1.3 Conventions ..........................................................................................3
Chapter 2. Hardware Installation .......................................................................... 4
2.1 The Front Panel..................................................................................... 4
2.2 The Back Panel .....................................................................................6
2.3 Installation Environment ........................................................................7
2.4 Connecting the Modem Router.............................................................. 8
Chapter 3. Quick Installation Guide ................................................................... 10
3.1 TCP/IP Configuration...........................................................................10
3.2 Login....................................................................................................11
Chapter 4. Software Configuration..................................................................... 17
4.1 Status ..................................................................................................17
4.1.1 Device Info............................................................................................... 17
4.1.2 System Log.............................................................................................. 18
4.1.3 Statistics .................................................................................................. 19
4.2 Quick Start...........................................................................................21
4.3 Interface Setup ....................................................................................22
4.3.1 Internet..................................................................................................... 22
4.3.2 LAN.......................................................................................................... 32
4.3.3 Wireless ...................................................................................................36
4.3.4 6RD.......................................................................................................... 48
4.4 Advanced Setup ..................................................................................49
4.4.1 Firewall .................................................................................................... 49
4.4.2 Routing .................................................................................................... 49
4.4.3 NAT.......................................................................................................... 50
4.4.4 QoS.......................................................................................................... 54
4.4.5 VLAN .......................................................................................................57
4.4.6 ADSL .......................................................................................................59
4.5 Access Management ...........................................................................60
4.5.1 ACL.......................................................................................................... 60
4.5.2 Filter......................................................................................................... 61
4.5.3 SNMP ......................................................................................................70
4.5.4 UPnP ....................................................................................................... 70
4.5.5 DDNS....................................................................................................... 71
4.5.6 CWMP ..................................................................................................... 72
4.6 Maintenance........................................................................................ 73
4.6.1 Administration ..........................................................................................73
4.6.2 Time Zone................................................................................................ 73
4.6.3 Firmware.................................................................................................. 75
4.6.4 SysRestart ...............................................................................................77
4.6.5 Diagnostics ..............................................................................................78
4.7 Help .....................................................................................................78
Appendix A: Specifications ................................................................................... 80
Appendix B: Troubleshooting ............................................................................... 81
Appendix C: Technical Support ............................................................................ 84
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Package Contents
The following contents should be found in your package:
One TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router
One Power Adapter for TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router
Quick Installation Guide
One RJ45 cable
Two RJ11 cables
One ADSL splitter
One Resource CD, which includes this User Guide
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
1
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 1. Introduction
Thank you for choosing the TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router.
1.1 Product Overview
The device is designed to provide a simple and cost-effective ADSL Internet connection for a
private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network.
The TD-W8951ND connects to an Ethernet LAN or computers via standard Ethernet ports. The
ADSL connection is made using ordinary telephone line with standard connectors. Multiple
workstations can be networked and connected to the Internet using a single Wide Area Network
(WAN) interface and single global IP address. The advanced security enhancements, IP/MAC
Filter, Application Filter and URL Filter can help to protect your network from potentially
devastating intrusions by malicious agents from the outside of your network.
Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the
configuration. Network and Router management is done through the Web-based Utility which can
be accessed through local Ethernet using any web browser.
ADSL
The TD-W8951ND supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI
specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports
dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer.
Wireless
In the most attentive wireless security, the modem router provides multiple protection measures. It
can be set to turn off the wireless network name (SSID) broadcast so that only stations that have
the SSID can be connected. The modem router provides wireless LAN 64/128-bit WEP encryption
security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security.
1.2 Main Features
Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.
Provides external splitter.
Adopts Advanced DMT modulation and demodulation technology.
Supports bridge mode and Router function.
Multi-user sharing a high-speed Internet connection.
2
Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps（With Annex M
enabled）.
Supports long transfers, the max line length can reach to 6.5Km.
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Supports remote configuration and management through SNMP
Supports PPPoE, it allows connecting the internet on demand and disconnecting from the
Internet when idle.
Provides reliable ESD and surge-protect function with quick response semi-conductive surge
protection circuit.
High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.
Supports All ADSL industrial standards.
Compatible with all mainstream DSLAM (CO).
Provides integrated access of internet and route function which face to SOHO user.
Real-time Configuration and device monitoring.
Supports Multiple PVC (Permanent Virtual Circuit).
Built-in DHCP server.
Built-in firewall, supporting IP/MAC filter, Application filter and URL filter.
and CWMP.
Supports Virtual Server, DMZ host and IP Address Mapping.
Supports Dynamic DNS, UPnP and Static Routing.
Supports system log and flow Statistics.
Supports firmware upgrade and Web management.
Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security.
Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).
1.3 Conventions
The modem router or device mentioned in this User Guide stands for TD-W8951ND without any
explanations.
Parameters provided in the pictures are just references for setting up the product, which may differ
from the actual situation.
3
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 2. Hardware Installation
2.1 The Front Panel
Figure 2-1
The LEDs locate on the front panel. They indicate the device’s working status. For details, please
LED Explanation:
Name Status Indication
On The modem router is powered on.
(Power)
Off
On ADSL line is synchronized and ready to use.
The modem router is off. Please ensure that the power adapter is
connected correctly.
(ADSL)
(Internet)
(WLAN)
(WPS)
Flash The ADSL negotiation is in progress.
Off
On The network is available with a successful Internet connection.
Flash There is data being transmitted or received via the Internet.
Off
On Wireless is enabled but no data is being transmitted.
Flash
Off Wireless function is disabled.
On
Flash
Off
ADSL synchronization fails. Please refer to Note 1
troubleshooting.
There is no successful Internet connection or the modem router is
operating in Bridge mode. Please refer to Note 2
The modem router is sending or receiving data over the wireless
network.
A wireless device has been successfully added to the network by
WPS function.
WPS handshaking is in process and will continue for about 2
minutes. Please press the WPS button on other wireless devices
that you want to add to the network while the LED is flashing.
The WPS function is disabled or the wireless device fails to be added
to the network in 2 minutes after WPS function is enabled. Please
refer to 4.3.3.1 WPS Settings
for more information.
for
for troubleshooting.
(LAN 1-4)
On There is a device connected to this LAN port.
Flash The modem router is sending or receiving data over this LAN port.
Off There is no device connected to this LAN port.
4
Note:
1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting
the Modem Router for more information about how to make Internet connection correctly. If
you have already made a right connection, please contact your ISP to make sure if your
Internet service is available now.
2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off,
please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet
configuration. You may need to check this part of information with your ISP and make sure
everything have been input correctly. Refer to 4.1.1 Device Info
information.
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
and 4.3.1 Internet for more
5
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
2.2 The Back Panel
Figure 2-2
POWER: The Power plug is where you will connect the power adapter.
ON/OFF: The switch for the power.
WPS: This button is for WPS settings. For details, please refer to 4.3.3.1 WPS Settings
RESET: There are two ways to reset the modem router's factory defaults.
Method one: With the modem router powered on, use a pin to press and hold the Reset
button for at least 5 seconds. And the modem router will reboot to its factory default settings.
Method two: Restore the default setting from “Maintenance-SysRestart” of the modem
router's Web-based Utility.
6
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
WiFi:
1, 2, 3, 4 (LAN): Through the port, you can connect the modem router to your PC or the other
ADSL: Through the port, you can connect the modem router with the telephone. Or you can
Antenna: Used for wireless operation and data transmit.
Press this button to enable or disable Wireless LAN interface.
Ethernet network devices.
connect them by an external separate splitter. For details, please refer to 2.4 Connecting the
Modem Router.
2.3 Installation Environment
The Product should not be located where it will be exposed to moisture or excessive heat.
Place the modem router in a location where it can be connected to the various devices as well
as to a power source.
Make sure the cables and power cord are safely placed out of the way so they do not create a
tripping hazard.
The modem router can be placed on a shelf or desktop.
Keep away from the strong electromagnetic radiation and the device of electromagnetic
sensitive.
Generally, TD-W8951ND is placed on a horizontal surface. The device also can be mounted on
the wall as shown in Figure 2-3 Wall-mount Install.
7
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 2-
Note:
The diameter of the screw, 3.5mm<D<7.8mm, and the distance of two screws is 107.5mm. The
screw that project from the wall need around 4mm based, and the length of the screw need to be
at least 20mm to withstand the weight of the product.
3 Wall-mount Install
2.4 Connecting the Modem Router
Before installing the device, please make sure your broadband service provided by your ISP is
available. If there is any problem, please contact your ISP. Before cable connection, cut off the
power supply and keep your hands dry. You can follow the steps below to install it.
Step 1: Connect the ADSL Line.
Method one: Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear
panel of TD-W8951ND, and insert the other end into the wall socket.
Method two：You can use a separate splitter. External splitter can divide the data and
voice, and then you can access the Internet and make calls at the same time. The
external splitter has three ports:
8
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
• LINE: Connect to
• PHONE: Connect to the phone sets
• MODEM: Connect to the ADSL port of TD-W8951ND
Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of
TD-W8951ND. Connect the other end to the MODEM port of the external splitter.
Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s
Ethernet port or a regular hub/switch port, and the other end to the LAN port on the
TD-W8951ND.
Step 3: Power on the computers and LAN devices.
Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear
of the device and plug in the adapter to a electrical outlet or power extension. The
electrical outlet shall be installed near the device and shall be easily accessible.
the wall jack
Figure 2-4
9
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 3. Quick Installation Guide
3.1 TCP/IP Configuration
The default IP address of the TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router is
192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you
desire. In this guide, we use all the default values for description.
Connect the local PC to the LAN port of the Modem Router. And then you can configure the IP
address for your PC by the following way:
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to T3 in Appendix B:
Troubleshooting
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select run tab, type cmd or command in the field
and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
modem router has been established.
.
Figure 3-1
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the modem router.
10
You can check it follow the steps below:
1) Is the connection between your PC and the modem router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should
be lit.
2) Is the TCP/IP configuration for your PC correct?
If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the
range of 192.168.1.2 ~ 192.168.1.254.
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-2
3.2 Login
Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:
Start your web browser and type the private IP address of the modem router in the URL field:
192.168.1.1.
After that, you will see the screen shown below, enter the default User Name admin and the
default Password admin, and then click OK to access to the Quick Start screen. You can follow
the steps below to complete the Quick Start.
11
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-3
Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen.
Click the NEXT button.
Figure 3-4
Step 2: Configure the time for the modem router, and then click the NEXT button.
12
Step 3: Select the Connection Type given by your ISP(Internet Service Provider), and then click
NEXT.
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-5
Figure 3-6
Step 4: There are four connection types: Dynamic IP Address, Static IP Address, PPPoE/PPPoA
and Bridge Mode. Please choose the connection type that your ISP provides. After that,
you should follow the configuration below to proceed.
1) Select Dynamic IP Address in Figure 3-6, the next screen will appear as shown in
Figure 3-7. Configure the following options provided by your ISP: VPI, VCI and
Connection T
ype. Then click NEXT.
13
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-7
2) Select Static IP Address in Figure 3-6, the next screen will appear as shown in
Figure 3-8.Configure the following options provided by your ISP: VP
I, VCI, IP
Address, Subnet Mask, ISP Gateway and Connection Type. Then click NEXT.
Figure 3-8
DNS Relay: If you want to disable this feature, you just need to set both Primary and
secondary DNS IP to 0.0.0.0. If you want to use DNS relay, you can setup DNS server
IP to 192.168.1.1 on their Computer. If not, the device will perform as no DNS relay.
Primary DNS Server: Type in your preferred DNS server.
Secondary DNS Server: Type in your preferred DNS server.
14
Note:
If Use Auto Discovered DNS Server Only is selected in DNS Relay, this modem router will
accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled
PVC(s) during the connection establishment. If Use User Discovered DNS Server Only is
selected in DNS Relay, it is necessary for you to enter the primary and optional secondary DNS
server IP addresses. After type in the address, click SAVE button to save it and invoke it.
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
3) Select PPPoE/PPPoA in Figure 3-6, the next screen will appear as shown
Configure the following options provided by your ISP: Username, Password, VPI, VCI
and Connection Type. Then click NEXT.
Figure 3-9
4) Select Bridge Mode in Figure 3-6, the next screen will appear as shown in Figure 3-10.
in Figure 3-9.
Configur
Then click NEXT.
Step 5: After finishing the Connection Type selection, configure the rules for the WLAN, and click
NEXT.
e the following options provided by your ISP: VPI, VCI and Connection Type.
Figure 3-10
15
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-11
Note:
If the Access Point is activated, the wireless function will be available even without the external
antenna because of an additional printed antenna. To adopt the wireless security protection
measures, please refer to 4.3.3 Wireless
Step 6: Click NEXT to finish the Quick Start.
.
Figure 3-12
16
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 4. Software Configuration
This User Guide recommends using the “Quick Installation Guide” for first-time installation. For
advanced users, if you want to know more about this device and make use of its functions
adequately, maybe you will get help from this chapter to configure the advanced settings through
the Web-based Utility.
After your successful login, you can configure and manage the device. There are main menus on
the top of the Web-based Utility; submenus will be available after you click one of the main menus.
On the center of the Web-based Utility, there are the detailed configurations or status information.
To apply any settings you have altered on the page, please click the SAVE button.
4.1 Status
Choose “Status”, you can see the next submenus: Device Info, System Log and Statistics.
Click any of them, and you will be able to configure the corresponding function.
Figure 4-1
Click any of them, and you will be able to view the corresponding information.
4.1.1 Device Info
Choose “Status→Device Info” menu, and you will be able to view the device information,
including LAN, WAN and ADSL. The information will vary depending on the settings of the modem
router configured on the Interface Setup screen.
17
TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-2
Note:
Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the
system log a
nd traffic statistics about the modem router.
4.1.2 System Log
Choose “Status→System Log” menu, and you will be able to query the logs of the modem router.
18
Loading...