TP Link TDW8901NV3 User Manual
TD-W8901N
REV: 3.0.0
1910011
150Mbps Wireless N ADSL2+ Modem Router
395
COPYRIGHT & TRADEMARKS
Specifications are subject to change w ith out not ice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademar ks o f their r espective holders.
No part of the specificat io ns may be repr oduc ed in any for m or by any mean s or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or t elevision reception, which can be determined by turning the equipment o ff
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation bet w een the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an exper i enced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1） This device may not cause harmful interference.
2） This device must accept any inter ference rece ived, includi ng interfere nce that may cau se
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s auth or ity to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification s to this equipment. Such modificati ons could void t he user’s author ity to
operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmit t er .
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other ant enna or t r ansmitter.”
CE Mark Warning
This is a class B product. In a do mestic env iron ment , this product may cause r adio inter feren ce, in
which case the user may be required to take adequate measures.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two condit i ons:
(1) This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est sou mis aux deux conditions suivantes:
(1) cet appareil ne doit pa s pr ovoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souh ait é de l’appareil.
Industry Canada Statement
Complies with the Canad i an I CE S-003 Class B specifications.
Cet appareil numérique de la cl asse B est conforme à la norme NM B-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射
頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
UkrSEPRO
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Informati on
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the pro duct, or make repa irs yourself. You r un the risk of electr ic shock and
voiding the limited warrant y. If you need service, please cont act us .
Avoid water and wet locations.
This product can be used in the f ol low i ng countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US
TP-LINK TECHNOLOGIES CO., L TD
DECLRATION OF CONFORMITY
For the following equipme nt:
Product Description: 150 Mbp s Wireless N ADSL2 + Modem Router
Model No.: TD-W8901N
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
applicable to the product w it hin the scope of Council Directiv es:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following st andards or other normative docu m ents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013
EN 50385: 2002
The product carries the CE Mark:
Person responsible for m aking this declaration:
Yang Hongliang
Product Manage r of International B us i ness
Date of issue: 2015-08-20
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
CONTENTS
Package Contents .................................................................................................... 1
Chapter 1. Introduction ......................................................................................... 2
1.1 Product Overview .................................................................................. 2
1.2 Main Features ....................................................................................... 2
1.3 Conventions .......................................................................................... 3
Chapter 2. Hardware Installati on .......................................................................... 4
2.1 The Front Panel ..................................................................................... 4
2.2 The Back Panel ..................................................................................... 5
2.3 Installation Environment ........................................................................ 6
2.4 Connecting the Modem Router .............................................................. 7
Chapter 3. Quick Installation Guide ..................................................................... 9
3.1 TCP/IP Configuration ............................................................................. 9
3.2 Login .................................................................................................... 10
Chapter 4. Software Configuration ..................................................................... 14
4.1 Status .................................................................................................. 14
4.1.1 Device Info ................................................................................................. 14
4.1.2 System Log ................................................................................................ 15
4.1.3 Statistics ..................................................................................................... 16
4.2 Quick Start ........................................................................................... 18
4.3 Interface Setup .................................................................................... 19
4.3.1 Internet ....................................................................................................... 19
4.3.2 LAN ............................................................................................................ 29
4.3.3 Wireless ...................................................................................................... 33
4.3.4 6RD ............................................................................................................ 44
4.4 Advanced Setup .................................................................................. 45
4.4.1 Firewall ....................................................................................................... 45
4.4.2 Routing ....................................................................................................... 45
4.4.3 NAT ............................................................................................................ 47
.4 QoS ............................................................................................................ 50
4.4
4.4.5 VLAN .......................................................................................................... 53
4.4.6 ADSL .......................................................................................................... 55
4.5 Access Management ........................................................................... 56
4.5.1 ACL ............................................................................................................ 56
4.5.2 Filter ........................................................................................................... 58
4.5.3 SNMP ......................................................................................................... 67
4.5.4 UPnP .......................................................................................................... 67
4.5.5 DDNS ......................................................................................................... 68
4.5.6 CWMP ........................................................................................................ 69
4.6 Maintenance ........................................................................................ 70
4.6.1 Administration ............................................................................................ 70
4.6.2 Time Zone .................................................................................................. 70
4.6.3 Firmware .................................................................................................... 72
4.6.4 SysRestart .................................................................................................. 74
4.6.5 Diagnostics ................................................................................................. 74
4.7 Help ..................................................................................................... 75
Appendix A: Specifications ................................................................................... 77
Appendix B: Troubleshooting ............................................................................... 78
Appendix C: Technical Support ............................................................................ 81
TD-W8151N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Package Contents
The following contents should be found in your package:
One TD-W8901N 150Mb ps Wireless N ADSL2+ Mode m Router
One Pow er Adapt er for TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router
Quick Installation Gui de
One RJ 45 c able
Two RJ11 cabl es
One ADSL splitter
One Resour ce CD, which includes this Us er G uide
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact y our distr i butor.
1
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 1. Introduction
Thank you for choosing the TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router.
1.1 Product O verview
The device is designed to provide a simple and cost-effective ADSL Internet connection for a
private Ethernet or IEEE 802. 11n/ IEEE 802.11g/ IEEE 802.11b wireless networ k.
The TD-W8901N connects to an Ethernet LAN or computers via standard Ethernet ports. The
ADSL connection is made using ordinary telephone line with standard connectors. Multiple
workstations can be networked and connected to the Internet using a single Wide Area Network
(WAN) interface and single global IP address. The advanced security enhancements, IP/MAC
Filter, Application Filter and URL Filter can help to protect your network from potentially
devastating intrusions by malicious agents from the outside of your network.
Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the
configuration. Network and Router management is done through the Web-based Utility w hich can
be accessed through local Et hernet using any web browser.
ADSL
The TD-W8901N supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI
specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports
dual latency ADSL2+ fra m ing (f as t and interleaved) and the I.432 A TM Physical Layer.
Wireless
In the most attentive wireless secur it y, the mode m router provides multiple protect ion me asure s. I t
can be set to turn off the wireless network name (SSID) broadcast so that only stations that have
the SSID can be connected. The m odem rout er provides wireless LAN 64/12 8-bit WEP encryption
security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security.
1.2 Main Fea t ures
Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/ M DI X), one RJ11 port.
Provides external splitter.
Adopt s Advanced DMT m odulatio n and demodu lati on technol ogy.
Support s br i dge mode and Router function.
Multi-user sharin g a high-speed Internet connecti on.
2
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Downstream data rates up to 24Mbps, upstream data rates up to 2.5Mbps（With Annex M
enabled）.
Support s lo ng t r ansfers, the max line length can re ach t o 6.5Km.
Support s r emote configuration and management through SNMP
Supports PPPoE, it allows connecting the Internet on demand and disconnecting from the
Internet when idle.
Provides reliable ESD and surge-protect function with quick response semi-cond uc ti ve su rge
protection circuit.
High sp eed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.
Support s All ADSL industrial standards.
Compatible with all mainstream DSLAM (CO).
Provides integrated access to Internet and route function which face to SOHO user.
Real-time Configuration and device monitoring.
Support s M ultiple PVC (Permanent Virtual Circuit).
Built-in DHCP server.
Built-in firewall, supporting IP/MAC filter, Application filter and URL filter.
and CWMP.
Support s V irtual Server, DMZ host and I P Ad dr ess Mapping.
Support s Dy namic DNS, UPnP and Static Rout ing.
Supports system log and flow Statistics.
Support s f irmware upgrade and Web management.
Provides WPA-PSK/WPA2-PSK data s ecurity, TKIP/AES encrypt ion security.
Provides 64/128-bit WEP encrypt ion security and wireless LAN ACL (Access Control List).
Support s I Pv6.
1.3 Conventions
The modem router or device mentioned in this User Guide stands for TD-W8901N without any
explanations.
Parameters provided in the pictur es are just referen ces for setting up the pr oduct, w hich may differ
from the actual situation.
3
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 2. Hardware Install at ion
2.1 The Front P ane l
Figure 2-1
The LEDs locate on the front panel. They indicate the device’s working status. For details, please
refer to LEDs Explanation.
LEDs Explanation:
Name Status Indication
On The modem router is powered on.
(Power)
Off
The modem router is off. Please ensure that the power adapt er is
connected correctly.
(ADSL)
(Internet)
(WLAN)
(WPS)
On ADSL line is synchronized and ready t o use.
Flash The ADSL negotiation is in progress.
Off
On The network is available with a succes sful Internet connection.
Flash There is data being transm itt ed or r eceived via the Internet.
Off
On Wireless is enabled.
Off Wireless function is disabled.
On Wireless is enabled but no data is being t ransmitted.
Flash
Off
On There is a device connected to this LAN p or t.
ADSL synchronization fai ls. Please refer to Note 1
troubleshooting.
There is no successful Int er net connection or the modem router is
operating in Bridge mode. Please refer to Note 2 for troubleshooting.
WPS handshaking is in process and will continue for about 2
minutes. Please press the WPS button on other wireless devices
that you want to add to the network while the LED is flashing.
The WPS funct ion is disa bled or the wireles s devic e fails to be add ed
to the network in 2 minutes after WPS function is enabled. Please
refer to WPS Settings
for more information.
for
(LAN 1-4)
Note:
1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting
the Modem Router for more information about how to make Internet connection correctly. If
Flash The modem router is send ing or r eceiving data over this LAN por t .
Off There is no device connected to this LA N port .
4
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
you have already made a right connection, please contact your ISP to make sure if your
Internet service is available now.
2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off,
please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet
configuration. You may need to check this part of information with your ISP and make sure
everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet
information.
f or m ore
5
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
POWER ON/OFF
WPS/
RESET
WiFi
LAN4
LAN3
LAN2
LAN1
ADSL
2.2 The Back Panel
Figure 2-2
POWER: The Power plug is wher e you will connect the power ad apt er .
ON/OFF: The switch for t he power.
WiFi: Press this but t on to enable or disable Wireless LAN interface.
WPS/RESET: The switch for the WPS function. If your client devices, such as wireless
adapters, support Wi-Fi Protected Setup, then you can press this button for about two
seconds to quickly establish a connection between the router and client devices and
automatically configure w ir eless sec urity for y our w ireless net wor k. For det ails, plea se re fer t o
WPS Settings.
If you press this button for more than 8 seconds, you will enable the RESET
function. There are tw o w ays to reset the modem router's factory defaults.
6
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Method one: With the modem router powered on, press and hold down the WPS/RESET
button on the rear panel for at least 8 seconds until some LEDs go off, then release the
button.
Method two: Restore the default setting from “Maintenance-SysRestart” of the modem
router's Web-based Utility.
4, 3, 2, 1 (LAN): Through the port, you can connect t he m odem router to your PC or t he ot her
Ethernet network devices.
ADSL: Through the port, you can connect the modem router with the telephone. Or you can
connect them by an external separate splitter. For details, please refer to
Modem Router.
Antenna: Used for wireless operation and data transmit.
2.4 Connecting the
2.3 Installation Environment
The Product should not be located where it will be exposed to moisture or ex ces sive heat.
Place the m odem router in a location where it can be connected t o the various devices as w ell
as to a power source.
Ma ke sure the cab les a nd pow er cor d ar e safely placed out of the way so th ey do not cr eat e a
tripping hazard.
The modem router can be placed on a shelf or desktop.
Keep away from the strong electromagnetic radiation and the device of electromagnetic
sensitive.
Generally, TD-W8901N is placed on a horizontal surface. The device also can be mounted on the
wall as shown in Figure 2-3.
Figure 2-3 Wall-mount Ins tall
7
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
：
Note:
The diameter of the screw, 3.5m m<D<8 mm, an d the distance o f tw o screw s is 118mm. The scre w
that project from the wall need arou nd 4 mm bas ed, a nd the len gth of the s crew need t o be at least
20mm to withstand the weight of the product.
2.4 Connecti ng t he Modem Router
Before installing the device, please make sure your broadband service provided by your ISP is
available. If there is any problem, please contact your ISP. Before cable connection, cut off the
power supply and keep your hands dr y. You can follow the steps be low t o install it.
Step 1: Connect the ADSL Line.
Method one: P lu g one en d of the t wi sted-pa ir A DSL cable into th e ADSL port on the rea r
panel of TD-W8901N, and insert the other end into the wall socket.
Method two
voice, and then you can access the Internet and make calls at the same time. The
external splitter has three por t s:
• LINE: Connect to the wall jack
• PHONE: Connect to the phone sets
• MODEM: Connect to the ADSL port of TD-W8901N
Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of
TD-W8901N. Connect the other end to the MODEM port of t he ext er nal splitter.
Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s
Ethernet port or a regular hub/switch port, and the other end to the LAN port on the
TD-W8901N.
Step 3: Power on the computers and LAN devi c es.
Step 4: Attach the power adapter. Connect the p ower adapt e r to t he power connector on the rear
of the device and plug in the adapter to an electrical outlet or power extension. The
You can use a separate splitter. External splitter can divide the data and
electrical outlet shall be in stalled near the device and shall be easily accessible.
8
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Ethernet Cabl e
Computer
Phone Cable
LINE
Splitter
Phone Cable
Wall Socket
POWER ON/OFF
WPS/
RESET
WiFi
LAN4
LAN3
LAN2
LAN1
ADSL
Fig
PHONE MODEM
ure 2-4
9
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 3. Quick Installation Guide
3.1 TCP/IP Configuration
The default IP address of the TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router is
192.168.1.1. And the default Sub net Mas k is 255.255.255. 0. These v alues can be chang ed as you
desire. In this guide, we use al l t he default values for description.
Connect the local PC to the LAN port of the Modem Router. And then you can configure your PC
to an obtain IP address in the following way:
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to T3 in
Troubleshooting.
2) Then the built-in D H CP s erver will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please c lick the Start menu on your desktop, select run tab, type cmd or command in the field
and press Enter. Type ping 192.168.1.1 on the next screen, and t hen press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
modem router has been e stablished.
Appendix B:
Figure 3-1
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the modem rout er .
10
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-2
You can check it follow the st eps below:
1) Is the conne ction between your PC and the modem router correct?
The LEDs of LAN port whi ch y ou lin k to the d ev ice and t he LE Ds on y our PC's adapter s hou ld
be lit.
2) Is the TCP/IP configurat i on for your PC correct?
If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the
range of 192.168.1.2 ~ 19 2. 168. 1. 254.
3.2 Login
Once your host PC is prop erly configured, please proceed as fo llows t o us e the Web-based Utility:
Launch your web browser and ent er http://tplinkmodem.net or 192.168.1.1 in the address bar.
After that, you will see the screen shown below, enter the default User Name admin and the
default Password admin, and then click Login to access to the Web-Management page. You can
follow the steps below to c om pl et e the Quick Start.
11
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-3
Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen.
Click the NEXT button.
Figure 3-4
Step 2: Configure the time for the modem router, and then click the NEXT button.
Figure 3-5
12
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Step 3: Select your country and ISP, and select your ISP Connection type (Here we take
PPPoE/PPPoA mode for example), and complete the corresponding settings with the
information provided by your ISP, then click the NEXT button.
Figure 3-6
Note:
Per FCC regulation s, all Wi-Fi products marketed in t he U.S. must be fixed to the U.S. region on ly.
Step 4: After finishing the Internet Settings, configure the rules for the WLAN, and cli ck NEXT.
13
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-7
Note:
If the Access Point is activated, the wireless function will be available even without the external
antenna because of an additional printed antenna. To adopt the wireless security protection
measures, please refer to 4.3.3 Wireless.
Step 5: Click SAVE to finish the Quick St ar t .
Figure 3-8
14
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 4. Software Configuration
This User Guide recommends using the “Quick Installation Guide” for first-time installation. For
advanced users, if you want to know more about this device and make use of its functions
adequately, maybe you will get help from this chapter to configure the advanced settings through
the Web-based Utility.
After your successful login, you can configure and manage the device. There are main menus on
the top of the Web-based Utility; subm enus will be av ailable after y ou click one of t he main menus.
On the center of the Web-based Utility, there are the detailed configurations or status information.
To apply any settings you hav e alter ed on the page, please click the SAVE button.
4.1 Status
Choose “Status”, you can see the next submenus: Device Info, System Log and Statistics.
Click any of them, and you w il l be able to configure the corresponding function.
Figure 4-1
Click any of them, and you w il l be able to view the corresponding information.
4.1.1 Device Info
Choose “Status→Device Info” menu, and you will be able to view the device information,
including LAN, WAN and ADSL. The inf ormatio n wil l var y dependin g on t he set tings o f the modem
router configured on the I nt er fac e Set up screen.
15
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-2
Note:
Click the other submenus System Log or Statistics in Figure 4-2, and you wil l be abl e to v iew t he
system log and traffic statistics about the modem router.
4.1.2 System Log
Choose “Status→System Log” menu, and you will be able to query the logs of the modem router.
16
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-3
The modem router can keep logs of all traf fic. Y ou c an qu ery the log s to f ind w hat hap pen ed to th e
Router.
Click the CLEAR LOG button to clear the logs.
Click the SAVE LO G button to save the logs.
4.1.3 Statistics
Choose “Status→Statistics” menu, and you will be able to view the net work traffic over Ethernet,
ADSL and WLAN.
17
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
over the Ethernet
over the Ethernet
Figure 4-4
Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network
traffic over different ports.
Select Ethernet, and you will see the stat i stics table as below.
Statistics Table:
Transmit
Statistics
Receive
Statistics
Transmit Frames
Transmit Multicast Frames
Transmit total Bytes
Transmit Collision
Transmit Error Frames
Receive Frames
Receive Multicast Frames
Receive total Bytes
Receive CRC Errors
Receive Under-size Frames
The frames transmitted over the Ethernet port.
The multicast frames transmitted
port.
The total bytes transmitted over the Ethernet port.
The collision occurred over the Ethernet port when
data is being transmitted.
The error frames over the Ethernet port when data is
being transmitted.
The frames received over the Ethernet port.
The multicast frames received over the Ethernet port.
The total bytes received over the Ethernet port.
The CRC errors occurred over the Ethernet port when
data is being received.
The Under-size frames received
18
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
when wireless data is
Select ADSL, and you will see the s t at ist i cs table as below.
Statistics Table:
Transmit
Statistics
Transmit total PDUs The total PDUs transmitted over the ADSL port.
Transmit total Error Counts
The total errors occurred over the ADS L port when data
is being tra nsmitted.
Receive
Statistics
Receive total PDUs The total PDUs transmitted over the ADSL port.
Receive total Error Counts
The total errors oc curred over the ADSL port when data
is being received.
Select WLAN, and you will see the statistics t able as below.
Statistics Table:
The frames transmitted over the WLAN
being transmitted.
The errors occurred over the WLAN when wireless dat a is be ing
transmitted.
The drops occurred over the WLAN when wireless data is being
transmitted.
Transmit
Statistics
Tx Frames Count
Tx Errors Count
Tx Drops Count
The frames received over the W LAN when wireless data is being
transmitted.
The errors occurred over the WLAN when wireless data is being
received.
The drops occurred over the WLAN when wireless data is being
received.
Receive
Statistics
Rx Frames Count
Rx Errors Count
Rx Drops Count
Click the REFRESH button to refresh immediately.
4.2 Quick Start
Please refer to 3.2 Login.
19
TD-W8901N
150Mbps Wireless N ADSL2+ Modem Router User Guide
4.3 Interface Setup
Choose “Interface Setup”, you can see the next submenus:.
Figure 4-5
Click any of them, and you w il l be able to configure the corresponding function.
4.3.1 Internet
Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in
the next screen (shown in Figure 4-6).
20
Loading...