TP-Link LS1005G, LS1008G Installation Guide

LED Explanation

Power

© 2020 TP-Link

7106509072 REV2.0.0

Installation Guide

5/8-Port Gigabit Desktop Switch

LS1005G/LS1008G

Note: For simplicity, we will take LS1008G for example throughout this Guide.

Connection

Link/Act

On: Power on

O: Power o

Link/Act (Green)

Running at 10/100/1000Mbps

On:

No device is linked to the

O:

corresponding port

Flashing: Transmitting/receiving data

Internet

Power Adapter

Router

LAN PortWAN Port

LS1008G

PC

Ethernet Ports (1-8)Power LED

PC

Frequently Asked Questions (FAQ)

Q1. The Power LED is not lit.

The Power LED should be lit when the power system is
working normally. If the Power LED is not lit, check as
follows:

Make sure the power adapter is connected to the

A1:

switch with power source properly.

Make sure the voltage of the power supply meets the

A2:

requirements of the input voltage of the switch.

A3:

Make sure the power source is ON.

Specications

General Specications

Standard

Protocol

Data Transfer Rate

Network Media (Cable)

Interface

LED Indicators

Transfer Method

MAC Address Learning

Frame Forward Rate

Wall Mountable

Distance Between
Mounting Holes

IEEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x

CSMA/CD

Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
10Base-T: UTP category 3, 4, 5 cable (maximum 100m)

EIA/TIA-568 100
100Base-TX: UTP category 5, 5e cable (maximum 100m)

EIA/TIA-568 100
1000Base-T: UTP category 5e cable (maximum 100m)

EIA/TIA-568 100Ω STP (maximum 100m)

5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports

Power, Link/Act LED

Store-and-Forward

Automatically learning, automatically aging

10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port

Ye s

LS1005G: 38mm
LS1008G: 48mm

Ω

STP (maximum 100m)

Ω

STP (maximum 100m)

Q2. The Link/Act LED is not lit when a device
is connected to the corresponding port.

It is recommended that you check the following items:

Make sure that the cable connectors are rmly plugged

A1:

into the switch and the device.

A2:

Make sure the connected device is turned on and
works normally.

A3:

The cable must be less than 100 meters long (328 feet).

Environmental and Physical Specications

Operating Temperature

Operating Humidity

Storage Humidity

To ask questions, nd answers, and communicate with

TP-Link users or engineers, please visit
https://community.tp-link.com to join TP-Link Community.

For technical support and other information,
please visit https://www.tp-link.com/support, or simply
scan the QR code.

If you have any suggestions or needs on the product guides,
welcome to email [e-mail].

0˚C to 40˚C (32˚F to 104˚F)

10% to 90%RH non-condensing

5% to 90%RH non-condensing

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.

Do not use damaged charger or USB cable to charge the device.

Do not use any other chargers than those recommended.

Adapter shall be installed near the equipment and shall be easily accessible.

TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC,
2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.