TP-Link LS1005 User Manual
Installation Guide
LED Explanation
Power
On: Power on
O: Power o
Link/Act
© 2020 TP-Link
7106508806 REV1.0.1
5/8-Port 10/100Mbps Desktop Switch
LS1005/LS1008
Note: For simplicity, we will take LS1008 for example throughout this Guide.
Running at 10/100Mbps
On:
No device is linked to the corresponding port
O:
Flashing: Transmitting/receiving data
Connection
Power LEDLink/Act LED
Ethernet Ports (1-8)
Power Adapter
PC
LS1008
PC
Internet
Router
LAN Port WAN Port
Frequently Asked Questions (FAQ)
Q1. The Power LED is not lit.
The Power LED should be lit when the power system is
working normally. If the Power LED is not lit, check as
follows:
Make sure the power adapter is connected to the
A1:
switch with power source properly.
A2:
Make sure the voltage of the power supply meets the
requirements of the input voltage of the switch.
A3:
Make sure the power source is ON.
Specications
General Specications
Standard
Protocol
Data Transfer Rate
Network Media (Cable)
Interface
LED Indicators
Transfer Method
MAC Address Learning
Frame Forward Rate
IEEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3x
CSMA/CD
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
Ω
EIA/TIA-568 100
STP (maximum 100m)
100Base-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100
Ω
STP (maximum 100m)
5/8 10/100Mbps Auto-Negotiation RJ45 Ports
Power, Link/Act LED
Store-and-Forward
Automatically learning, automatically aging
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
Q2. The Link/Act LED is not lit when a device
is connected to the corresponding port.
It is recommended that you check the following items:
Make sure that the cable connectors are rmly
A1:
plugged into the switch and the device.
A2:
Make sure the connected device is turned on and
works normally.
A3:
The cable must be less than 100 meters long (328 feet).
Environmental and Physical Specications
Operating Temperature
Operating Humidity
Storage Humidity
To ask questions, nd answers, and communicate with
TP-Link users or engineers, please visit
https://community.tp-link.com to join TP-Link Community.
For technical support and other information,
please visit https://www.tp-link.com/support, or simply
scan the QR code.
If you have any suggestions or needs on the product guides,
welcome to email techwriter@tp-link.com.cn.
0˚C to 40˚C (32˚F to 104˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC,
2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Loading...